Re: [PATCH 2/5] usb: gadget: s3c-hsotg: support configurable UTMI PHY width

[Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>]

[-- Attachment #1: Type: text/plain, Size: 4037 bytes --]

Hi,

On Thu, Oct 10, 2013 at 11:21:30PM -0400, Matt Porter wrote:
> On 10/10/2013 03:07 PM, Matt Porter wrote:
> >On 10/10/2013 01:57 PM, Paul Zimmerman wrote:
> >>>From: Felipe Balbi [mailto:balbi-l0cyMroinI0@public.gmane.org]
> >>>Sent: Thursday, October 10, 2013 10:46 AM
> >>>
> >>>On Thu, Oct 10, 2013 at 12:54:40PM -0400, Matt Porter wrote:
> >>>>On 10/10/2013 11:29 AM, Felipe Balbi wrote:
> >>>>>On Mon, Oct 07, 2013 at 06:12:29AM -0400, Matt Porter wrote:
> >>>>>>Extend dwc2 binding with an optional utmi phy width property.
> >>>>>>Enable the s3c-hsotg.c driver to use standard dwc2 binding
> >>>>>>and enable configuration of the UTMI phy width based on the
> >>>>>>property.
> >>>>>>
> >>>>>>Signed-off-by: Matt Porter <matt.porter-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> >>>>>>Reviewed-by: Markus Mayer <markus.mayer-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> >>>>>>Reviewed-by: Tim Kryger <tim.kryger-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> >>>>>>---
> >>>>>>  Documentation/devicetree/bindings/staging/dwc2.txt |  4 ++++
> >>>>>>  drivers/usb/gadget/s3c-hsotg.c                     | 18
> >>>>>>+++++++++++++++++-
> >>>>>>  drivers/usb/gadget/s3c-hsotg.h                     |  1 +
> >>>>>>  3 files changed, 22 insertions(+), 1 deletion(-)
> >>>>>>
> >>>>>>diff --git a/Documentation/devicetree/bindings/staging/dwc2.txt
> >>>b/Documentation/devicetree/bindings/staging/dwc2.txt
> >>>>>>index 1a1b7cf..fb6b8ee 100644
> >>>>>>--- a/Documentation/devicetree/bindings/staging/dwc2.txt
> >>>>>>+++ b/Documentation/devicetree/bindings/staging/dwc2.txt
> >>>>>>@@ -6,10 +6,14 @@ Required properties:
> >>>>>>  - reg : Should contain 1 register range (address and length)
> >>>>>>  - interrupts : Should contain 1 interrupt
> >>>>>>
> >>>>>>+Optional properties:
> >>>>>>+- snps,phy-utmi-width: Must contain the UTMI data width (either 8
> >>>>>>or 16)
> >>>>>
> >>>>>isn't this available in any of the configuration registers ?
> >>>>
> >>>>Yes and no. HWCFG4 has a UTMI data width field. However, it has 3
> >>>>valid states, "8", "16", or "8 or 16". The BCM281xx implementation is
> >>>>set to the latter and the attached phy is 8-bit.
> >>>>
> >>>>Looking at dwc2 prior to Matthijs Kooijman's patch [1] which starts
> >>>>validating the value of phy_utmi_width in that driver, the pci.c
> >>>>dwc2_module_params .phy_utmi_width field there even had the comment,
> >>>>"/* 16 bits - NOT DETECTABLE */". The autodetect code in
> >>>>dwc2_set_param_phy_utmi_width() will fail if HWCFG4 has the "8 or 16"
> >>>>option as it just decides to default to a phy width of 16 if nothing
> >>>>is configured by the platform glue. This property would also allow
> >>>>this issue to be addressed in that driver.
> >>>
> >>>fair enough, but I'd really like to hear from DT folks if your suggested
> >>>binding is acceptable. It seems like we can equally argue that it's a SW
> >>>configuration or HW description.
> >>
> >>It's definitely a HW description - the width of the UTMI data connection.
> >>
> >>But, which PHY is this? Does it have a register that could tell what
> >>the data width is? The dwc2 core has an (optional) PHY Vendor Control
> >>Register that allows reading the PHY registers.
> >
> >This is the integrated PHY on the bcm28155 part (the entire
> >bcm281xx/11351 family shares it). My register doc doesn't show the
> >optional PHY vendor control register as being present in this dwc2
> >implementation. I'll track down with the design team if this is
> >accurate...but it appears we can't go that route.
> 
> The design team confirmed that we do not have any registers that can
> be accessed via the PHY Vendor Control Register. All PHY control
> registers are implemented in the MMIO control block which is
> supported in the PHY control driver later in this series.They also
> confirmed there's no other way to detect that it's an 8-bit data
> path.

then we need the DT binding, let's see what DT maintainers say.

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]