From mboxrd@z Thu Jan 1 00:00:00 1970 From: Andre Heider Subject: Re: [PATCH] staging: dwc2: set up all module params Date: Tue, 26 Nov 2013 13:01:46 +0100 Message-ID: <20131126120146.GA31736@localhost> References: <1385442150-23561-1-git-send-email-swarren@wwwdotorg.org> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Return-path: Content-Disposition: inline In-Reply-To: <1385442150-23561-1-git-send-email-swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> Sender: devicetree-owner-u79uwXL29TY76Z2rM5mHXA@public.gmane.org To: Stephen Warren Cc: Greg Kroah-Hartman , Mark Rutland , devel-gWbeCf7V1WCQmaza687I9mD2FQJk+8+b@public.gmane.org, Pawel Moll , Ian Campbell , Rob Herring , devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, Paul Zimmerman List-Id: devicetree@vger.kernel.org On Mon, Nov 25, 2013 at 10:02:30PM -0700, Stephen Warren wrote: > The DWC2 USB controller in the BCM2835 (Raspberry Pi) needs some non- > default parameters. Select these based on the compatible value from the > DT node. For all other HW, fall back to the default parameters currently > in use. > > The values in params_bcm2835[] were posted to the mailing list by Paul > quite some time ago. I made a couple of minor modifications since then; > to set ahbcfg instead of ahb_single, and to set uframe_sched. > > Signed-off-by: Stephen Warren > --- > Documentation/devicetree/bindings/staging/dwc2.txt | 4 +- > drivers/staging/dwc2/platform.c | 56 ++++++++++++++++---- > 2 files changed, 50 insertions(+), 10 deletions(-) > > diff --git a/Documentation/devicetree/bindings/staging/dwc2.txt b/Documentation/devicetree/bindings/staging/dwc2.txt > index 1a1b7cf..8b60e90 100644 > --- a/Documentation/devicetree/bindings/staging/dwc2.txt > +++ b/Documentation/devicetree/bindings/staging/dwc2.txt > @@ -2,7 +2,9 @@ Platform DesignWare HS OTG USB 2.0 controller > ----------------------------------------------------- > > Required properties: > -- compatible : "snps,dwc2" > +- compatible : One of: > + - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC. > + - snps,dwc2: A generic DWC2 USB controller with default parameters. > - reg : Should contain 1 register range (address and length) > - interrupts : Should contain 1 interrupt > > diff --git a/drivers/staging/dwc2/platform.c b/drivers/staging/dwc2/platform.c > index 4d9fac0..20586dc 100644 > --- a/drivers/staging/dwc2/platform.c > +++ b/drivers/staging/dwc2/platform.c > @@ -39,6 +39,7 @@ > #include > #include > #include > +#include > #include > > #include "core.h" > @@ -46,6 +47,33 @@ > > static const char dwc2_driver_name[] = "dwc2"; > > +static const struct dwc2_core_params params_bcm2835 = { > + .otg_cap = 0, /* HNP/SRP capable */ > + .otg_ver = 0, /* 1.3 */ > + .dma_enable = 1, > + .dma_desc_enable = 0, > + .speed = 0, /* High Speed */ > + .enable_dynamic_fifo = 1, > + .en_multiple_tx_fifo = 1, > + .host_rx_fifo_size = 774, /* 774 DWORDs */ > + .host_nperio_tx_fifo_size = 256, /* 256 DWORDs */ > + .host_perio_tx_fifo_size = 512, /* 512 DWORDs */ > + .max_transfer_size = 65535, > + .max_packet_count = 511, > + .host_channels = 8, > + .phy_type = 1, /* UTMI */ > + .phy_utmi_width = 8, /* 8 bits */ > + .phy_ulpi_ddr = 0, /* Single */ > + .phy_ulpi_ext_vbus = 0, > + .i2c_enable = 0, > + .ulpi_fs_ls = 0, > + .host_support_fs_ls_low_power = 0, > + .host_ls_low_power_phy_clk = 0, /* 48 MHz */ > + .ts_dline = 0, > + .reload_ctl = 0, > + .ahbcfg = 0x10, > +}; > + > /** > * dwc2_driver_remove() - Called when the DWC_otg core is unregistered with the > * DWC_otg driver > @@ -66,6 +94,13 @@ static int dwc2_driver_remove(struct platform_device *dev) > return 0; > } > > +static const struct of_device_id dwc2_of_match_table[] = { > + { .compatible = "brcm,bcm2835-usb", .data = ¶ms_bcm2835 }, > + { .compatible = "snps,dwc2", .data = NULL }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, dwc2_of_match_table); > + > /** > * dwc2_driver_probe() - Called when the DWC_otg core is bound to the DWC_otg > * driver > @@ -80,14 +115,23 @@ static int dwc2_driver_remove(struct platform_device *dev) > */ > static int dwc2_driver_probe(struct platform_device *dev) > { > + const struct of_device_id *match; > + const struct dwc2_core_params *params; > + struct dwc2_core_params defparams; > struct dwc2_hsotg *hsotg; > struct resource *res; > int retval; > int irq; > - struct dwc2_core_params params; > + > + match = of_match_device(dwc2_of_match_table, &dev->dev); > + if (match) > + params = match->data; > + else { > + dwc2_set_all_params(&defparams, -1); > + params = &defparams; > + } If that matches "snps,dwc2", params will be NULL instead of the default set, which I guess was not your intention? > > /* Default all params to autodetect */ > - dwc2_set_all_params(¶ms, -1); The comment can be moved too. > > hsotg = devm_kzalloc(&dev->dev, sizeof(*hsotg), GFP_KERNEL); > if (!hsotg) > @@ -118,7 +162,7 @@ static int dwc2_driver_probe(struct platform_device *dev) > dev_dbg(&dev->dev, "mapped PA %08lx to VA %p\n", > (unsigned long)res->start, hsotg->regs); > > - retval = dwc2_hcd_init(hsotg, irq, ¶ms); > + retval = dwc2_hcd_init(hsotg, irq, params); > if (retval) > return retval; > > @@ -127,12 +171,6 @@ static int dwc2_driver_probe(struct platform_device *dev) > return retval; > } > > -static const struct of_device_id dwc2_of_match_table[] = { > - { .compatible = "snps,dwc2" }, > - {}, > -}; > -MODULE_DEVICE_TABLE(of, dwc2_of_match_table); > - > static struct platform_driver dwc2_platform_driver = { > .driver = { > .name = dwc2_driver_name, > -- > 1.7.10.4 > > _______________________________________________ > devel mailing list > devel-tBiZLqfeLfOHmIFyCCdPziST3g8Odh+X@public.gmane.org > http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html