* Re: [PATCH 2/4] DT: Vendor prefixes: Add ricoh, ssi and synology
[not found] ` <1391634309-3123-3-git-send-email-andrew-g2DYL2Zd6BY@public.gmane.org>
@ 2014-02-06 15:19 ` Jason Cooper
0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-02-06 15:19 UTC (permalink / raw)
To: Andrew Lunn
Cc: linux ARM, devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
pawel.moll-5wv7dgnIgG8, Mark Rutland, Ian Campbell, Kumar Gala
+ devicetree ML, DT maintainers.
On Wed, Feb 05, 2014 at 10:05:07PM +0100, Andrew Lunn wrote:
> The following patches make use of vendor names ricoh, ssi and
> synology. Add them to the vendor prefix list.
>
> Signed-off-by: Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.txt | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 3f900cd51bf0..1629e8f33578 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -69,6 +69,7 @@ ralink Mediatek/Ralink Technology Corp.
> ramtron Ramtron International
> realtek Realtek Semiconductor Corp.
> renesas Renesas Electronics Corporation
> +ricoh Richoh Co. Ltd.
s/Richoh/Ricoh/
other than that,
Acked-by: Jason Cooper <jason-NLaQJdtUoK4Be96aLqz0jA@public.gmane.org>
thx,
Jason.
> rockchip Fuzhou Rockchip Electronics Co., Ltd
> samsung Samsung Semiconductor
> sbs Smart Battery System
> @@ -76,11 +77,13 @@ schindler Schindler
> sil Silicon Image
> silabs Silicon Laboratories
> simtek
> +sii Seiko Instruments, Inc.
> sirf SiRF Technology, Inc.
> snps Synopsys, Inc.
> st STMicroelectronics
> ste ST-Ericsson
> stericsson ST-Ericsson
> +synology Synology, Inc.
> ti Texas Instruments
> tlm Trusted Logic Mobility
> toshiba Toshiba Corporation
> --
> 1.7.10.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 3/4] DT: i2c: Trivial: Add sii,s35390a
[not found] ` <1391634309-3123-4-git-send-email-andrew-g2DYL2Zd6BY@public.gmane.org>
@ 2014-02-06 15:21 ` Jason Cooper
0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-02-06 15:21 UTC (permalink / raw)
To: Andrew Lunn
Cc: linux ARM, devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
pawel.moll-5wv7dgnIgG8, Mark Rutland, Ian Campbell, Kumar Gala
+ devicetree ML, DT maintainers
On Wed, Feb 05, 2014 at 10:05:08PM +0100, Andrew Lunn wrote:
> Add the Seiko Instruments Inc S35390a to the list of trivial i2c
> devices.
>
> Signed-off-by: Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>
> ---
> Documentation/devicetree/bindings/i2c/trivial-devices.txt | 1 +
> 1 file changed, 1 insertion(+)
Acked-by: Jason Cooper <jason-NLaQJdtUoK4Be96aLqz0jA@public.gmane.org>
thx,
Jason.
> diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
> index 1a1ac2e560e9..e11ed0fe770c 100644
> --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
> +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
> @@ -58,6 +58,7 @@ plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch
> ramtron,24c64 i2c serial eeprom (24cxx)
> ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
> samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power)
> +sii,s35390a 2-wire CMOS real-time clock
> st-micro,24c256 i2c serial eeprom (24cxx)
> stm,m41t00 Serial Access TIMEKEEPER
> stm,m41t62 Serial real-time clock (RTC) with alarm
> --
> 1.7.10.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
[not found] ` <1391634309-3123-5-git-send-email-andrew@lunn.ch>
@ 2014-02-06 15:39 ` Jason Cooper
2014-02-06 16:01 ` Andrew Lunn
2014-02-06 16:39 ` Ian Campbell
0 siblings, 2 replies; 12+ messages in thread
From: Jason Cooper @ 2014-02-06 15:39 UTC (permalink / raw)
To: Andrew Lunn
Cc: Mark Rutland, devicetree, Ben Peddell, pawel.moll, Kumar Gala,
Ian Campbell, linux ARM
+ devicetree ML, DT maintainers
On Wed, Feb 05, 2014 at 10:05:09PM +0100, Andrew Lunn wrote:
> Add device tree fragments and files to support many of the kirkwood
> based Synology NAS devices. This is a translation of the board setup
> file maintained by Ben Peddell <klightspeed@killerwolves.net>
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Tested by Ben Peddell <klightspeed@killerwolves.net>
> cc: Ben Peddell <klightspeed@killerwolves.net>
> ---
>
> v2:
> Fix gpio's which should be gpo.
> Rebase onto v3-14-rc1
> Update RTC nodes with vendor name.
> Update SPI flash node with vendor name.
> ---
> arch/arm/boot/dts/Makefile | 15 ++++
> arch/arm/boot/dts/kirkwood-ds109.dts | 33 +++++++
> arch/arm/boot/dts/kirkwood-ds110jv10.dts | 33 +++++++
> arch/arm/boot/dts/kirkwood-ds111.dts | 33 +++++++
> arch/arm/boot/dts/kirkwood-ds112.dts | 34 +++++++
> arch/arm/boot/dts/kirkwood-ds209.dts | 33 +++++++
> arch/arm/boot/dts/kirkwood-ds210.dts | 35 ++++++++
> arch/arm/boot/dts/kirkwood-ds212.dts | 37 ++++++++
> arch/arm/boot/dts/kirkwood-ds212j.dts | 34 +++++++
> arch/arm/boot/dts/kirkwood-ds409.dts | 34 +++++++
> arch/arm/boot/dts/kirkwood-ds409slim.dts | 32 +++++++
> arch/arm/boot/dts/kirkwood-ds411.dts | 35 ++++++++
> arch/arm/boot/dts/kirkwood-ds411j.dts | 34 +++++++
> arch/arm/boot/dts/kirkwood-ds411slim.dts | 34 +++++++
> arch/arm/boot/dts/kirkwood-rs212.dts | 34 +++++++
> arch/arm/boot/dts/kirkwood-rs409.dts | 33 +++++++
> arch/arm/boot/dts/kirkwood-rs411.dts | 34 +++++++
> arch/arm/boot/dts/synology/alarm-led-12.dtsi | 28 ++++++
> arch/arm/boot/dts/synology/common.dtsi | 112 ++++++++++++++++++++++++
> arch/arm/boot/dts/synology/ethernet-1.dtsi | 15 ++++
> arch/arm/boot/dts/synology/fan-alarm-18.dtsi | 22 +++++
> arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi | 22 +++++
> arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi | 32 +++++++
> arch/arm/boot/dts/synology/fan-gpios-15.dtsi | 34 +++++++
> arch/arm/boot/dts/synology/fan-gpios-32.dtsi | 34 +++++++
> arch/arm/boot/dts/synology/fan-speed-100.dtsi | 20 +++++
> arch/arm/boot/dts/synology/fan-speed-120.dtsi | 20 +++++
> arch/arm/boot/dts/synology/fan-speed-150.dtsi | 20 +++++
> arch/arm/boot/dts/synology/hdd-leds-20.dtsi | 90 +++++++++++++++++++
> arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi | 36 ++++++++
> arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi | 52 +++++++++++
> arch/arm/boot/dts/synology/hdd-leds-36.dtsi | 103 ++++++++++++++++++++++
> arch/arm/boot/dts/synology/hdd-leds-38.dtsi | 52 +++++++++++
> arch/arm/boot/dts/synology/hdd-power-29.dtsi | 56 ++++++++++++
> arch/arm/boot/dts/synology/hdd-power-30-1.dtsi | 40 +++++++++
> arch/arm/boot/dts/synology/hdd-power-30-2.dtsi | 56 ++++++++++++
> arch/arm/boot/dts/synology/hdd-power-30-4.dtsi | 89 +++++++++++++++++++
> arch/arm/boot/dts/synology/hdd-power-31.dtsi | 40 +++++++++
> arch/arm/boot/dts/synology/hdd-power-34.dtsi | 73 +++++++++++++++
> arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi | 18 ++++
> arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi | 18 ++++
> arch/arm/boot/dts/synology/pcie-2.dtsi | 19 ++++
> 42 files changed, 1658 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts
> create mode 100644 arch/arm/boot/dts/synology/alarm-led-12.dtsi
> create mode 100644 arch/arm/boot/dts/synology/common.dtsi
> create mode 100644 arch/arm/boot/dts/synology/ethernet-1.dtsi
> create mode 100644 arch/arm/boot/dts/synology/fan-alarm-18.dtsi
> create mode 100644 arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi
> create mode 100644 arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi
> create mode 100644 arch/arm/boot/dts/synology/fan-gpios-15.dtsi
> create mode 100644 arch/arm/boot/dts/synology/fan-gpios-32.dtsi
> create mode 100644 arch/arm/boot/dts/synology/fan-speed-100.dtsi
> create mode 100644 arch/arm/boot/dts/synology/fan-speed-120.dtsi
> create mode 100644 arch/arm/boot/dts/synology/fan-speed-150.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-20.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-36.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-38.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-power-29.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-1.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-2.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-4.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-power-31.dtsi
> create mode 100644 arch/arm/boot/dts/synology/hdd-power-34.dtsi
> create mode 100644 arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi
> create mode 100644 arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi
> create mode 100644 arch/arm/boot/dts/synology/pcie-2.dtsi
Holy sh*t! I know we're adding 15 boards, but this is, imho,
over-fragmenting. I'm sure there's a reason you chose this path, but
you haven't explained why in your commit log. So I'm left guessing...
thx,
Jason.
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b9d6a8b485e0..6cf3a54ef7f1 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -89,6 +89,18 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
> kirkwood-dns325.dtb \
> kirkwood-dockstar.dtb \
> kirkwood-dreamplug.dtb \
> + kirkwood-ds109.dtb \
> + kirkwood-ds110jv10.dtb \
> + kirkwood-ds111.dtb \
> + kirkwood-ds209.dtb \
> + kirkwood-ds210.dtb \
> + kirkwood-ds212.dtb \
> + kirkwood-ds212j.dtb \
> + kirkwood-ds409.dtb \
> + kirkwood-ds409slim.dtb \
> + kirkwood-ds411.dtb \
> + kirkwood-ds411j.dtb \
> + kirkwood-ds411slim.dtb \
> kirkwood-goflexnet.dtb \
> kirkwood-guruplug-server-plus.dtb \
> kirkwood-ib62x0.dtb \
> @@ -111,6 +123,9 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
> kirkwood-nsa310a.dtb \
> kirkwood-openblocks_a6.dtb \
> kirkwood-openblocks_a7.dtb \
> + kirkwood-rs212.dtb \
> + kirkwood-rs409.dtb \
> + kirkwood-rs411.dtb \
> kirkwood-sheevaplug.dtb \
> kirkwood-sheevaplug-esata.dtb \
> kirkwood-topkick.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/kirkwood-ds109.dts
> new file mode 100644
> index 000000000000..bea085ad540a
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds109.dts
> @@ -0,0 +1,33 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-ricoh.dtsi"
> +#include "synology/fan-speed-150.dtsi"
> +#include "synology/fan-gpios-32.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-21-1.dtsi"
> +
> +/ {
> + model = "Synology DS109, DS110, DS110jv20";
> + compatible = "synology,ds109", "synology,ds110jv20",
> + "synology,ds110", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/kirkwood-ds110jv10.dts
> new file mode 100644
> index 000000000000..d6b746952947
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds110jv10.dts
> @@ -0,0 +1,33 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/fan-speed-150.dtsi"
> +#include "synology/fan-gpios-32.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-21-1.dtsi"
> +
> +/ {
> + model = "Synology DS110j v10 and v30";
> + compatible = "synology,ds110jv10", "synology,ds110jv30",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/kirkwood-ds111.dts
> new file mode 100644
> index 000000000000..5f51e088903f
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds111.dts
> @@ -0,0 +1,33 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "synology/pcie-2.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/fan-speed-100.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-21-1.dtsi"
> +
> +/ {
> + model = "Synology DS111";
> + compatible = "synology,ds111", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/kirkwood-ds112.dts
> new file mode 100644
> index 000000000000..cda3203a0824
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds112.dts
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "synology/pcie-2.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/fan-speed-100.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-35.dtsi"
> +#include "synology/hdd-leds-21-2.dtsi"
> +#include "synology/hdd-power-30.dtsi"
> +
> +/ {
> + model = "Synology DS111";
> + compatible = "synology,ds111", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/kirkwood-ds209.dts
> new file mode 100644
> index 000000000000..b2ebb423e129
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds209.dts
> @@ -0,0 +1,33 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-ricoh.dtsi"
> +#include "synology/fan-speed-150.dtsi"
> +#include "synology/fan-gpios-32.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-21-2.dtsi"
> +#include "synology/hdd-power-31.dtsi"
> +
> +/ {
> + model = "Synology DS209";
> + compatible = "synology,ds209", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/kirkwood-ds210.dts
> new file mode 100644
> index 000000000000..8623dd63f44d
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds210.dts
> @@ -0,0 +1,35 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/fan-speed-150.dtsi"
> +#include "synology/fan-gpios-32.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-21-2.dtsi"
> +#include "synology/hdd-power-31.dtsi"
> +
> +/ {
> + model = "Synology DS210 v10, v20, v30, DS211j";
> + compatible = "synology,ds210jv10", "synology,ds210jv20",
> + "synology,ds210jv30", "synology,ds211j",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/kirkwood-ds212.dts
> new file mode 100644
> index 000000000000..89e091ce2174
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds212.dts
> @@ -0,0 +1,37 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "synology/pcie-2.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/fan-speed-100.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-21-2.dtsi"
> +#include "synology/hdd-power-30-2.dtsi"
> +
> +/ {
> + model = "Synology DS212, DS212p v10, v20, DS213air v10, DS213 v10";
> + compatible = "synology,ds212", "synology,ds212pv10",
> + "synology,ds212pv10", "synology,ds212pv20",
> + "synology,ds213airv10", "synology,ds213v10",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/kirkwood-ds212j.dts
> new file mode 100644
> index 000000000000..ed14b7bb695e
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds212j.dts
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/fan-speed-100.dtsi"
> +#include "synology/fan-gpios-32.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-21-2.dtsi"
> +#include "synology/hdd-power-29.dtsi"
> +
> +/ {
> + model = "Synology DS212j v10, v20";
> + compatible = "synology,ds212jv10", "synology,ds212jv20",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/kirkwood-ds409.dts
> new file mode 100644
> index 000000000000..7000de1add08
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds409.dts
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-ricoh.dtsi"
> +#include "synology/ethernet-1.dtsi"
> +#include "synology/fan-speed-120.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-18.dtsi"
> +#include "synology/hdd-leds-36.dtsi"
> +#include "synology/alarm-led-12.dtsi"
> +
> +/ {
> + model = "Synology DS409, DS410j";
> + compatible = "synology,ds409", "synology,ds410j", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/kirkwood-ds409slim.dts
> new file mode 100644
> index 000000000000..0ba525a594f7
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds409slim.dts
> @@ -0,0 +1,32 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-ricoh.dtsi"
> +#include "synology/fan-speed-120.dtsi"
> +#include "synology/fan-gpios-32.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-20.dtsi"
> +
> +/ {
> + model = "Synology 409slim";
> + compatible = "synology,ds409slim", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/kirkwood-ds411.dts
> new file mode 100644
> index 000000000000..4c1ca8e85559
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds411.dts
> @@ -0,0 +1,35 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "synology/pcie-2.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/ethernet-1.dtsi"
> +#include "synology/fan-speed-100.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-36.dtsi"
> +#include "synology/hdd-power-34.dtsi"
> +
> +/ {
> + model = "Synology DS411, DS413jv10";
> + compatible = "synology,ds411", "synology,ds413jv10", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/kirkwood-ds411j.dts
> new file mode 100644
> index 000000000000..7f08a46ddabb
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds411j.dts
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/ethernet-1.dtsi"
> +#include "synology/fan-speed-120.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-18.dtsi"
> +#include "synology/hdd-leds-36.dtsi"
> +#include "synology/alarm-led-12.dtsi"
> +
> +/ {
> + model = "Synology DS411j";
> + compatible = "synology,ds411j", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/kirkwood-ds411slim.dts
> new file mode 100644
> index 000000000000..2e6d66f37002
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ds411slim.dts
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "synology/pcie-2.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/ethernet-1.dtsi"
> +#include "synology/fan-speed-100.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-35-1.dtsi"
> +#include "synology/hdd-leds-36.dtsi"
> +
> +/ {
> + model = "Synology DS411slim";
> + compatible = "synology,ds411slim", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/kirkwood-rs212.dts
> new file mode 100644
> index 000000000000..edc797464983
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-rs212.dts
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "synology/pcie-2.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/fan-speed-100.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-35-3.dtsi"
> +#include "synology/hdd-leds-38.dtsi"
> +#include "synology/hdd-power-30-2.dtsi"
> +
> +/ {
> + model = "Synology RS212";
> + compatible = "synology,rs212", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/kirkwood-rs409.dts
> new file mode 100644
> index 000000000000..906664a99602
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-rs409.dts
> @@ -0,0 +1,33 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-ricoh.dtsi"
> +#include "synology/ethernet-1.dtsi"
> +#include "synology/fan-speed-120.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-18.dtsi"
> +#include "synology/hdd-leds-36.dtsi"
> +
> +/ {
> + model = "Synology RS409";
> + compatible = "synology,rs409", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/kirkwood-rs411.dts
> new file mode 100644
> index 000000000000..75c806ea0dc9
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-rs411.dts
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6282.dtsi"
> +#include "synology/pcie-2.dtsi"
> +#include "synology/common.dtsi"
> +#include "synology/i2c-rtc-seiko.dtsi"
> +#include "synology/ethernet-1.dtsi"
> +#include "synology/fan-speed-100.dtsi"
> +#include "synology/fan-gpios-15.dtsi"
> +#include "synology/fan-alarm-35-3.dtsi"
> +#include "synology/hdd-leds-36.dtsi"
> +
> +/ {
> + model = "Synology RS411 RS812";
> + compatible = "synology,rs411", "synology,rs812", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/alarm-led-12.dtsi b/arch/arm/boot/dts/synology/alarm-led-12.dtsi
> new file mode 100644
> index 000000000000..e6ea8f07d1a5
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/alarm-led-12.dtsi
> @@ -0,0 +1,28 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_led_12: pmx-led-12 {
> + marvell,pins = "mpp12";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_led_12>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:alarm";
> + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/common.dtsi b/arch/arm/boot/dts/synology/common.dtsi
> new file mode 100644
> index 000000000000..fb078c4f9a62
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/common.dtsi
> @@ -0,0 +1,112 @@
> +/*
> + * Nodes which are common to all Synology devices
> + *
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + mbus {
> + pcie-controller {
> + status = "okay";
> +
> + pcie@1,0 {
> + status = "okay";
> + };
> + };
> + };
> + ocp@f1000000 {
> + i2c@11000 {
> + status = "okay";
> + clock-frequency = <400000>;
> + pinctrl-0 = <&pmx_twsi0>;
> + pinctrl-names = "default";
> + };
> + serial@12000 {
> + status = "okay";
> + pinctrl-0 = <&pmx_uart0>;
> + pinctrl-names = "default";
> + };
> + serial@12100 {
> + status = "okay";
> + pinctrl-0 = <&pmx_uart1>;
> + pinctrl-names = "default";
> + };
> + poweroff@12100 {
> + compatible = "synology,power-off";
> + reg = <0x12000 0x100>;
> + clocks = <&gate_clk 7>;
> + };
> + spi@10600 {
> + status = "okay";
> + pinctrl-0 = <&pmx_spi>;
> + pinctrl-names = "default";
> +
> + m25p80@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "st,m25p80";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + mode = <0>;
> +
> + partition@00000000 {
> + reg = <0x00000000 0x00080000>;
> + label = "RedBoot";
> + };
> +
> + partition@00080000 {
> + reg = <0x00080000 0x00200000>;
> + label = "zImage";
> + };
> +
> + partition@00280000 {
> + reg = <0x00280000 0x00140000>;
> + label = "rd.gz";
> + };
> + partition@003c0000 {
> + reg = <0x003c0000 0x00010000>;
> + label = "vendor";
> + };
> + partition@003d0000 {
> + reg = <0x003d0000 0x00020000>;
> + label = "RedBoot config";
> + };
> + partition@003f0000 {
> + reg = <0x003f0000 0x00010000>;
> + label = "FIS directory";
> + };
> + };
> + };
> + sata@80000 {
> + pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
> + pinctrl-names = "default";
> + status = "okay";
> + nr-ports = <2>;
> + };
> + };
> + gpio_fan {
> + compatible = "gpio-fan";
> + };
> +};
> +
> +&mdio {
> + status = "okay";
> +
> + ethphy0: ethernet-phy {
> + device_type = "ethernet-phy";
> + reg = <8>;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet0-port@0 {
> + phy-handle = <ðphy0>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/synology/ethernet-1.dtsi b/arch/arm/boot/dts/synology/ethernet-1.dtsi
> new file mode 100644
> index 000000000000..bf00eff53bbc
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/ethernet-1.dtsi
> @@ -0,0 +1,15 @@
> +&mdio {
> + status = "okay";
> +
> + ethphy1: ethernet-phy {
> + device_type = "ethernet-phy";
> + reg = <9>;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet1-port@0 {
> + phy-handle = <ðphy1>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/synology/fan-alarm-18.dtsi b/arch/arm/boot/dts/synology/fan-alarm-18.dtsi
> new file mode 100644
> index 000000000000..d323eb0d2109
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/fan-alarm-18.dtsi
> @@ -0,0 +1,22 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_fan_18: pmx-fan-18 {
> + marvell,pins = "mpp18";
> + marvell,function = "gpo";
> + };
> + };
> + };
> + gpio_fan {
> + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi b/arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi
> new file mode 100644
> index 000000000000..12e52fdae870
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi
> @@ -0,0 +1,22 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_fan_35: pmx-fan-35 {
> + marvell,pins = "mpp35";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio_fan {
> + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi b/arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi
> new file mode 100644
> index 000000000000..e2a44f402bf0
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi
> @@ -0,0 +1,32 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_fan_35: pmx-fan-35 {
> + marvell,pins = "mpp35";
> + marvell,function = "gpio";
> + };
> + pmx_fan_44: pmx-fan-44 {
> + marvell,pins = "mpp44";
> + marvell,function = "gpio";
> + };
> + pmx_fan_45: pmx-fan-45 {
> + marvell,pins = "mpp45";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio_fan {
> + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH
> + &gpio1 12 GPIO_ACTIVE_HIGH
> + &gpio1 13 GPIO_ACTIVE_HIGH>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/synology/fan-gpios-15.dtsi b/arch/arm/boot/dts/synology/fan-gpios-15.dtsi
> new file mode 100644
> index 000000000000..e27cba942eed
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/fan-gpios-15.dtsi
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_fan_15: pmx-fan-15 {
> + marvell,pins = "mpp15";
> + marvell,function = "gpio";
> + };
> + pmx_fan_16: pmx-fan-16 {
> + marvell,pins = "mpp16";
> + marvell,function = "gpio";
> + };
> + pmx_fan_17: pmx-fan-17 {
> + marvell,pins = "mpp17";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio_fan {
> + pinctrl-0 = <&pmx_fan_15 &pmx_fan_16 &pmx_fan_17>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH
> + &gpio0 16 GPIO_ACTIVE_HIGH
> + &gpio0 17 GPIO_ACTIVE_HIGH>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/synology/fan-gpios-32.dtsi b/arch/arm/boot/dts/synology/fan-gpios-32.dtsi
> new file mode 100644
> index 000000000000..d4fd393e71a8
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/fan-gpios-32.dtsi
> @@ -0,0 +1,34 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_fan_32: pmx-fan-32 {
> + marvell,pins = "mpp32";
> + marvell,function = "gpio";
> + };
> + pmx_fan_33: pmx-fan-33 {
> + marvell,pins = "mpp33";
> + marvell,function = "gpo";
> + };
> + pmx_fan_34: pmx-fan-34 {
> + marvell,pins = "mpp34";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio_fan {
> + pinctrl-0 = <&pmx_fan_32 &pmx_fan_33 &pmx_fan_34>;
> + pinctrl-names = "default";
> + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH
> + &gpio1 1 GPIO_ACTIVE_HIGH
> + &gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/synology/fan-speed-100.dtsi b/arch/arm/boot/dts/synology/fan-speed-100.dtsi
> new file mode 100644
> index 000000000000..5188ba59a9b2
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/fan-speed-100.dtsi
> @@ -0,0 +1,20 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + gpio_fan {
> + gpio-fan,speed-map = < 0 0
> + 2500 1
> + 3100 2
> + 3800 3
> + 4600 4
> + 4800 5
> + 4900 6
> + 5000 7 >;
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/fan-speed-120.dtsi b/arch/arm/boot/dts/synology/fan-speed-120.dtsi
> new file mode 100644
> index 000000000000..90157070492c
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/fan-speed-120.dtsi
> @@ -0,0 +1,20 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + gpio_fan {
> + gpio-fan,speed-map = < 0 0
> + 2500 1
> + 2700 2
> + 3000 4
> + 3600 3
> + 3800 5
> + 3900 6
> + 4300 7 >;
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/fan-speed-150.dtsi b/arch/arm/boot/dts/synology/fan-speed-150.dtsi
> new file mode 100644
> index 000000000000..6abc36915886
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/fan-speed-150.dtsi
> @@ -0,0 +1,20 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + gpio_fan {
> + gpio-fan,speed-map = < 0 0
> + 2200 1
> + 2500 2
> + 3000 4
> + 3300 3
> + 3700 5
> + 3800 6
> + 4200 7 >;
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-leds-20.dtsi b/arch/arm/boot/dts/synology/hdd-leds-20.dtsi
> new file mode 100644
> index 000000000000..e6663ea7014c
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-leds-20.dtsi
> @@ -0,0 +1,90 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_led_20: pmx-led-20 {
> + marvell,pins = "mpp20";
> + marvell,function = "gpio";
> + };
> + pmx_led_21: pmx-led-21 {
> + marvell,pins = "mpp21";
> + marvell,function = "gpio";
> + };
> + pmx_led_22: pmx-led-22 {
> + marvell,pins = "mpp22";
> + marvell,function = "gpio";
> + };
> + pmx_led_23: pmx-led-23 {
> + marvell,pins = "mpp23";
> + marvell,function = "gpio";
> + };
> + pmx_led_24: pmx-led-24 {
> + marvell,pins = "mpp24";
> + marvell,function = "gpio";
> + };
> + pmx_led_25: pmx-led-25 {
> + marvell,pins = "mpp25";
> + marvell,function = "gpio";
> + };
> + pmx_led_26: pmx-led-26 {
> + marvell,pins = "mpp26";
> + marvell,function = "gpio";
> + };
> + pmx_led_27: pmx-led-27 {
> + marvell,pins = "mpp27";
> + marvell,function = "gpio";
> + };
> + pmx_led_28: pmx-led-28 {
> + marvell,pins = "mpp28";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_led_20 &pmx_led_21 &pmx_led_22
> + &pmx_led_23 &pmx_led_24 &pmx_led_25
> + &pmx_led_26 &pmx_led_27>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-green {
> + label = "synology:green:hdd2";
> + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-amber {
> + label = "synology:amber:hdd2";
> + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
> + };
> + hdd3-green {
> + label = "synology:green:hdd3";
> + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
> + };
> + hdd3-amber {
> + label = "synology:amber:hdd3";
> + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
> + };
> + hdd4-green {
> + label = "synology:green:hdd4";
> + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
> + };
> + hdd4-amber {
> + label = "synology:amber:hdd4";
> + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi b/arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi
> new file mode 100644
> index 000000000000..034323f9ffb0
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi
> @@ -0,0 +1,36 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_led_21: pmx-led-21 {
> + marvell,pins = "mpp21";
> + marvell,function = "gpio";
> + };
> + pmx_led_23: pmx-led-23 {
> + marvell,pins = "mpp23";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_led_21 &pmx_led_23>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi b/arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi
> new file mode 100644
> index 000000000000..446a28f2200b
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi
> @@ -0,0 +1,52 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_led_20: pmx-led-20 {
> + marvell,pins = "mpp20";
> + marvell,function = "gpio";
> + };
> + pmx_led_21: pmx-led-21 {
> + marvell,pins = "mpp21";
> + marvell,function = "gpio";
> + };
> + pmx_led_22: pmx-led-22 {
> + marvell,pins = "mpp22";
> + marvell,function = "gpio";
> + };
> + pmx_led_23: pmx-led-23 {
> + marvell,pins = "mpp23";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_led_21 &pmx_led_23 &pmx_led_20 &pmx_led_22>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-green {
> + label = "synology:green:hdd2";
> + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-amber {
> + label = "synology:amber:hdd2";
> + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-leds-36.dtsi b/arch/arm/boot/dts/synology/hdd-leds-36.dtsi
> new file mode 100644
> index 000000000000..9541c0c943e6
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-leds-36.dtsi
> @@ -0,0 +1,103 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_led_36: pmx-led-36 {
> + marvell,pins = "mpp36";
> + marvell,function = "gpio";
> + };
> + pmx_led_37: pmx-led-37 {
> + marvell,pins = "mpp37";
> + marvell,function = "gpio";
> + };
> + pmx_led_38: pmx-led-38 {
> + marvell,pins = "mpp38";
> + marvell,function = "gpio";
> + };
> + pmx_led_39: pmx-led-39 {
> + marvell,pins = "mpp39";
> + marvell,function = "gpio";
> + };
> + pmx_led_40: pmx-led-40 {
> + marvell,pins = "mpp40";
> + marvell,function = "gpio";
> + };
> + pmx_led_41: pmx-led-41 {
> + marvell,pins = "mpp41";
> + marvell,function = "gpio";
> + };
> + pmx_led_42: pmx-led-42 {
> + marvell,pins = "mpp42";
> + marvell,function = "gpio";
> + };
> + pmx_led_43: pmx-led-43 {
> + marvell,pins = "mpp43";
> + marvell,function = "gpio";
> + };
> + pmx_led_44: pmx-led-44 {
> + marvell,pins = "mpp44";
> + marvell,function = "gpio";
> + };
> + pmx_led_45: pmx-led-45 {
> + marvell,pins = "mpp45";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_led_36 &pmx_led_37 &pmx_led_38
> + &pmx_led_39 &pmx_led_40 &pmx_led_41
> + &pmx_led_42 &pmx_led_43 &pmx_led_44
> + &pmx_led_45>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-green {
> + label = "synology:green:hdd2";
> + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-amber {
> + label = "synology:amber:hdd2";
> + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> + };
> + hdd3-green {
> + label = "synology:green:hdd3";
> + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
> + };
> + hdd3-amber {
> + label = "synology:amber:hdd3";
> + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
> + };
> + hdd4-green {
> + label = "synology:green:hdd4";
> + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
> + };
> + hdd4-amber {
> + label = "synology:amber:hdd4";
> + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
> + };
> + hdd5-green {
> + label = "synology:green:hdd5";
> + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
> + };
> + hdd5-amber {
> + label = "synology:amber:hdd5";
> + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-leds-38.dtsi b/arch/arm/boot/dts/synology/hdd-leds-38.dtsi
> new file mode 100644
> index 000000000000..d2fe351a0808
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-leds-38.dtsi
> @@ -0,0 +1,52 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_led_38: pmx-led-38 {
> + marvell,pins = "mpp38";
> + marvell,function = "gpio";
> + };
> + pmx_led_39: pmx-led-39 {
> + marvell,pins = "mpp39";
> + marvell,function = "gpio";
> + };
> + pmx_led_36: pmx-led-36 {
> + marvell,pins = "mpp36";
> + marvell,function = "gpio";
> + };
> + pmx_led_37: pmx-led-37 {
> + marvell,pins = "mpp37";
> + marvell,function = "gpio";
> + };
> + };
> + };
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_led_38 &pmx_led_39 &pmx_led_36 &pmx_led_37>;
> + pinctrl-names = "default";
> + hdd1-green {
> + label = "synology:green:hdd1";
> + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + };
> + hdd1-amber {
> + label = "synology:amber:hdd1";
> + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-green {
> + label = "synology:green:hdd2";
> + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + };
> + hdd2-amber {
> + label = "synology:amber:hdd2";
> + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-power-29.dtsi b/arch/arm/boot/dts/synology/hdd-power-29.dtsi
> new file mode 100644
> index 000000000000..8b08c86ab942
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-power-29.dtsi
> @@ -0,0 +1,56 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_hdd1_pwr_29: pmx-hdd1-pwr-29 {
> + marvell,pins = "mpp29";
> + marvell,function = "gpio";
> + };
> + pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 {
> + marvell,pins = "mpp31";
> + marvell,function = "gpio";
> + };
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd1_pwr_29 &pmx_hdd2_pwr_31>;
> + pinctrl-names = "default";
> +
> + hdd1_power: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd1power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
> + };
> + hdd2_power: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-power-30-1.dtsi b/arch/arm/boot/dts/synology/hdd-power-30-1.dtsi
> new file mode 100644
> index 000000000000..b0998d4e231f
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-power-30-1.dtsi
> @@ -0,0 +1,40 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 {
> + marvell,pins = "mpp30";
> + marvell,function = "gpio";
> + };
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd1_pwr_30>;
> + pinctrl-names = "default";
> +
> + hdd1_power: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd1power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-power-30-2.dtsi b/arch/arm/boot/dts/synology/hdd-power-30-2.dtsi
> new file mode 100644
> index 000000000000..766e6352d5af
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-power-30-2.dtsi
> @@ -0,0 +1,56 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 {
> + marvell,pins = "mpp30";
> + marvell,function = "gpio";
> + };
> + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 {
> + marvell,pins = "mpp34";
> + marvell,function = "gpio";
> + };
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34>;
> + pinctrl-names = "default";
> +
> + hdd1_power: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd1power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>;
> + };
> + hdd2_power: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-power-30-4.dtsi b/arch/arm/boot/dts/synology/hdd-power-30-4.dtsi
> new file mode 100644
> index 000000000000..5bbced207965
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-power-30-4.dtsi
> @@ -0,0 +1,89 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 {
> + marvell,pins = "mpp30";
> + marvell,function = "gpio";
> + };
> + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 {
> + marvell,pins = "mpp34";
> + marvell,function = "gpio";
> + };
> + pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 {
> + marvell,pins = "mpp44";
> + marvell,function = "gpio";
> + };
> + pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 {
> + marvell,pins = "mpp45";
> + marvell,function = "gpio";
> + };
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34
> + &pmx_hdd3_pwr_44 &pmx_hdd4_pwr_45>;
> + pinctrl-names = "default";
> +
> + hdd1_power: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd1power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>;
> + };
> + hdd2_power: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> + hdd3_power: regulator@3 {
> + compatible = "regulator-fixed";
> + reg = <3>;
> + regulator-name = "hdd3power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> + };
> + hdd4_power: regulator@4 {
> + compatible = "regulator-fixed";
> + reg = <4>;
> + regulator-name = "hdd3power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 32 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-power-31.dtsi b/arch/arm/boot/dts/synology/hdd-power-31.dtsi
> new file mode 100644
> index 000000000000..0774ecdcaf64
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-power-31.dtsi
> @@ -0,0 +1,40 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 {
> + marvell,pins = "mpp31";
> + marvell,function = "gpio";
> + };
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd2_pwr_31>;
> + pinctrl-names = "default";
> +
> + hdd2_power: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/hdd-power-34.dtsi b/arch/arm/boot/dts/synology/hdd-power-34.dtsi
> new file mode 100644
> index 000000000000..d90becf582f1
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/hdd-power-34.dtsi
> @@ -0,0 +1,73 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + pinctrl: pinctrl@10000 {
> +
> + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 {
> + marvell,pins = "mpp34";
> + marvell,function = "gpio";
> + };
> + pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 {
> + marvell,pins = "mpp44";
> + marvell,function = "gpio";
> + };
> + pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 {
> + marvell,pins = "mpp45";
> + marvell,function = "gpio";
> + };
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd2_pwr_34 &pmx_hdd3_pwr_44
> + &pmx_hdd4_pwr_45>;
> + pinctrl-names = "default";
> +
> + hdd2_power: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "hdd2power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> + hdd3_power: regulator@3 {
> + compatible = "regulator-fixed";
> + reg = <3>;
> + regulator-name = "hdd3power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> + };
> + hdd4_power: regulator@4 {
> + compatible = "regulator-fixed";
> + reg = <4>;
> + regulator-name = "hdd3power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + startup-delay-us = <5000000>;
> + gpio = <&gpio1 32 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi b/arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi
> new file mode 100644
> index 000000000000..920ad215462d
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi
> @@ -0,0 +1,18 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + i2c@11000 {
> + rs5c372: rs5c372@32 {
> + compatible = "ricoh,rs5c372a";
> + reg = <0x32>;
> + };
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi b/arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi
> new file mode 100644
> index 000000000000..4b5054bb4a87
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi
> @@ -0,0 +1,18 @@
> +/*
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + ocp@f1000000 {
> + i2c@11000 {
> + s35390a: s35390a@30 {
> + compatible = "sii,s35390a";
> + reg = <0x30>;
> + };
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/synology/pcie-2.dtsi b/arch/arm/boot/dts/synology/pcie-2.dtsi
> new file mode 100644
> index 000000000000..e34ebb5515c2
> --- /dev/null
> +++ b/arch/arm/boot/dts/synology/pcie-2.dtsi
> @@ -0,0 +1,19 @@
> +/*
> + * Nodes which are common to all Synology devices
> + *
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/ {
> + mbus {
> + pcie-controller {
> + pcie@2,0 {
> + status = "okay";
> + };
> + };
> + };
> +};
> \ No newline at end of file
> --
> 1.7.10.4
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
2014-02-06 15:39 ` [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices Jason Cooper
@ 2014-02-06 16:01 ` Andrew Lunn
2014-02-06 16:38 ` Arnd Bergmann
[not found] ` <20140206160126.GH29860-g2DYL2Zd6BY@public.gmane.org>
2014-02-06 16:39 ` Ian Campbell
1 sibling, 2 replies; 12+ messages in thread
From: Andrew Lunn @ 2014-02-06 16:01 UTC (permalink / raw)
To: Jason Cooper
Cc: Mark Rutland, Andrew Lunn, Ben Peddell, pawel.moll, devicetree,
Kumar Gala, Ian Campbell, linux ARM
On Thu, Feb 06, 2014 at 10:39:39AM -0500, Jason Cooper wrote:
>
> + devicetree ML, DT maintainers
>
> On Wed, Feb 05, 2014 at 10:05:09PM +0100, Andrew Lunn wrote:
> > Add device tree fragments and files to support many of the kirkwood
> > based Synology NAS devices. This is a translation of the board setup
> > file maintained by Ben Peddell <klightspeed@killerwolves.net>
> >
> > Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> > Tested by Ben Peddell <klightspeed@killerwolves.net>
> > cc: Ben Peddell <klightspeed@killerwolves.net>
> > ---
> >
> > v2:
> > Fix gpio's which should be gpo.
> > Rebase onto v3-14-rc1
> > Update RTC nodes with vendor name.
> > Update SPI flash node with vendor name.
> > ---
> > arch/arm/boot/dts/Makefile | 15 ++++
> > arch/arm/boot/dts/kirkwood-ds109.dts | 33 +++++++
> > arch/arm/boot/dts/kirkwood-ds110jv10.dts | 33 +++++++
> > arch/arm/boot/dts/kirkwood-ds111.dts | 33 +++++++
> > arch/arm/boot/dts/kirkwood-ds112.dts | 34 +++++++
> > arch/arm/boot/dts/kirkwood-ds209.dts | 33 +++++++
> > arch/arm/boot/dts/kirkwood-ds210.dts | 35 ++++++++
> > arch/arm/boot/dts/kirkwood-ds212.dts | 37 ++++++++
> > arch/arm/boot/dts/kirkwood-ds212j.dts | 34 +++++++
> > arch/arm/boot/dts/kirkwood-ds409.dts | 34 +++++++
> > arch/arm/boot/dts/kirkwood-ds409slim.dts | 32 +++++++
> > arch/arm/boot/dts/kirkwood-ds411.dts | 35 ++++++++
> > arch/arm/boot/dts/kirkwood-ds411j.dts | 34 +++++++
> > arch/arm/boot/dts/kirkwood-ds411slim.dts | 34 +++++++
> > arch/arm/boot/dts/kirkwood-rs212.dts | 34 +++++++
> > arch/arm/boot/dts/kirkwood-rs409.dts | 33 +++++++
> > arch/arm/boot/dts/kirkwood-rs411.dts | 34 +++++++
> > arch/arm/boot/dts/synology/alarm-led-12.dtsi | 28 ++++++
> > arch/arm/boot/dts/synology/common.dtsi | 112 ++++++++++++++++++++++++
> > arch/arm/boot/dts/synology/ethernet-1.dtsi | 15 ++++
> > arch/arm/boot/dts/synology/fan-alarm-18.dtsi | 22 +++++
> > arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi | 22 +++++
> > arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi | 32 +++++++
> > arch/arm/boot/dts/synology/fan-gpios-15.dtsi | 34 +++++++
> > arch/arm/boot/dts/synology/fan-gpios-32.dtsi | 34 +++++++
> > arch/arm/boot/dts/synology/fan-speed-100.dtsi | 20 +++++
> > arch/arm/boot/dts/synology/fan-speed-120.dtsi | 20 +++++
> > arch/arm/boot/dts/synology/fan-speed-150.dtsi | 20 +++++
> > arch/arm/boot/dts/synology/hdd-leds-20.dtsi | 90 +++++++++++++++++++
> > arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi | 36 ++++++++
> > arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi | 52 +++++++++++
> > arch/arm/boot/dts/synology/hdd-leds-36.dtsi | 103 ++++++++++++++++++++++
> > arch/arm/boot/dts/synology/hdd-leds-38.dtsi | 52 +++++++++++
> > arch/arm/boot/dts/synology/hdd-power-29.dtsi | 56 ++++++++++++
> > arch/arm/boot/dts/synology/hdd-power-30-1.dtsi | 40 +++++++++
> > arch/arm/boot/dts/synology/hdd-power-30-2.dtsi | 56 ++++++++++++
> > arch/arm/boot/dts/synology/hdd-power-30-4.dtsi | 89 +++++++++++++++++++
> > arch/arm/boot/dts/synology/hdd-power-31.dtsi | 40 +++++++++
> > arch/arm/boot/dts/synology/hdd-power-34.dtsi | 73 +++++++++++++++
> > arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi | 18 ++++
> > arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi | 18 ++++
> > arch/arm/boot/dts/synology/pcie-2.dtsi | 19 ++++
> > 42 files changed, 1658 insertions(+)
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts
> > create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts
> > create mode 100644 arch/arm/boot/dts/synology/alarm-led-12.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/common.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/ethernet-1.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/fan-alarm-18.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/fan-gpios-15.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/fan-gpios-32.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/fan-speed-100.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/fan-speed-120.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/fan-speed-150.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-leds-20.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-leds-36.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-leds-38.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-power-29.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-1.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-2.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-4.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-power-31.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/hdd-power-34.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi
> > create mode 100644 arch/arm/boot/dts/synology/pcie-2.dtsi
>
> Holy sh*t! I know we're adding 15 boards
More than 15 actually. Most .dts files support multiple devices. So
there should be about 30 devices supported by these .dts files.
, but this is, imho,
> over-fragmenting. I'm sure there's a reason you chose this path, but
> you haven't explained why in your commit log. So I'm left guessing...
Synology seem to build there devices like lego. They have two
different RTC blocks. They have three different fan alarm blocks, four
different led blocks, etc. And to build a product, the just select a
group of blocks and put them together.
The board setup code which Ben Peddell wrote has a somewhat similar
structure:
http://klightspeed.killerwolves.net/synology/linux-3.4-synology-0.1.patch
It has a set of functions which add platform devices. And a table
driven piece of code which based on the product name calls these
functions to add the needed platform devices. Take a look at the table
to get a better idea of the re-use factor of the blocks.
In this DT version, i have a dtsi file for each function, and a dti
file for each table entry.
I will add to the changelog in the next version.
Andrew
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
2014-02-06 16:01 ` Andrew Lunn
@ 2014-02-06 16:38 ` Arnd Bergmann
2014-02-06 17:03 ` Andrew Lunn
[not found] ` <20140206160126.GH29860-g2DYL2Zd6BY@public.gmane.org>
1 sibling, 1 reply; 12+ messages in thread
From: Arnd Bergmann @ 2014-02-06 16:38 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Mark Rutland, Andrew Lunn, Ben Peddell, Jason Cooper, pawel.moll,
devicetree, Ian Campbell, Kumar Gala
On Thursday 06 February 2014 17:01:26 Andrew Lunn wrote:
> , but this is, imho,
> > over-fragmenting. I'm sure there's a reason you chose this path, but
> > you haven't explained why in your commit log. So I'm left guessing...
>
> Synology seem to build there devices like lego. They have two
> different RTC blocks. They have three different fan alarm blocks, four
> different led blocks, etc. And to build a product, the just select a
> group of blocks and put them together.
I guess the Armada-370 and newer based ds213j and dsx14 will also be
able to reuse some of the blocks, right?
Arnd
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
2014-02-06 15:39 ` [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices Jason Cooper
2014-02-06 16:01 ` Andrew Lunn
@ 2014-02-06 16:39 ` Ian Campbell
[not found] ` <1391704765.2162.7.camel-ommiHX4a84BXesXXhkcM7miJhflN2719@public.gmane.org>
1 sibling, 1 reply; 12+ messages in thread
From: Ian Campbell @ 2014-02-06 16:39 UTC (permalink / raw)
To: Jason Cooper
Cc: Mark Rutland, Andrew Lunn, Ben Peddell, pawel.moll, devicetree,
Kumar Gala, linux ARM
On Thu, 2014-02-06 at 10:39 -0500, Jason Cooper wrote:
>
> > + pmx_fan_33: pmx-fan-33 {
> > + marvell,pins = "mpp33";
> > + marvell,function = "gpo";
> > + };
Typo I think.
Ian.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
[not found] ` <1391704765.2162.7.camel-ommiHX4a84BXesXXhkcM7miJhflN2719@public.gmane.org>
@ 2014-02-06 16:50 ` Andrew Lunn
2014-02-06 16:52 ` Ian Campbell
0 siblings, 1 reply; 12+ messages in thread
From: Andrew Lunn @ 2014-02-06 16:50 UTC (permalink / raw)
To: Ian Campbell
Cc: Jason Cooper, Andrew Lunn, linux ARM, Ben Peddell,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
pawel.moll-5wv7dgnIgG8, Mark Rutland, Kumar Gala
On Thu, Feb 06, 2014 at 04:39:25PM +0000, Ian Campbell wrote:
> On Thu, 2014-02-06 at 10:39 -0500, Jason Cooper wrote:
> >
> > > + pmx_fan_33: pmx-fan-33 {
> > > + marvell,pins = "mpp33";
> > > + marvell,function = "gpo";
> > > + };
>
> Typo I think.
Hi Ian
drivers/pinctrl/mvebu/pinctrl-kirkwood.c:
MPP_MODE(33,
MPP_VAR_FUNCTION(0x0, "gpo", NULL, V(0, 1, 1, 1, 1, 0)),
MPP_VAR_FUNCTION(0x2, "tdm", "dtx", V(0, 0, 1, 1, 1, 0)),
MPP_VAR_FUNCTION(0x3, "ge1", "txctl", V(0, 1, 1, 1, 1, 0)),
MPP_VAR_FUNCTION(0xb, "lcd", "d13", V(0, 0, 0, 0, 1, 0))),
MPP_MODE(34,
It is output only.
I actually had the opposite bug in v1, setup two gpo's as gpio's.
Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
2014-02-06 16:50 ` Andrew Lunn
@ 2014-02-06 16:52 ` Ian Campbell
0 siblings, 0 replies; 12+ messages in thread
From: Ian Campbell @ 2014-02-06 16:52 UTC (permalink / raw)
To: Andrew Lunn
Cc: Mark Rutland, devicetree, Ben Peddell, Jason Cooper, pawel.moll,
Kumar Gala, linux ARM
On Thu, 2014-02-06 at 17:50 +0100, Andrew Lunn wrote:
> On Thu, Feb 06, 2014 at 04:39:25PM +0000, Ian Campbell wrote:
> > On Thu, 2014-02-06 at 10:39 -0500, Jason Cooper wrote:
> > >
> > > > + pmx_fan_33: pmx-fan-33 {
> > > > + marvell,pins = "mpp33";
> > > > + marvell,function = "gpo";
> > > > + };
> >
> > Typo I think.
>
> Hi Ian
>
> drivers/pinctrl/mvebu/pinctrl-kirkwood.c:
>
> MPP_MODE(33,
> MPP_VAR_FUNCTION(0x0, "gpo", NULL, V(0, 1, 1, 1, 1, 0)),
> MPP_VAR_FUNCTION(0x2, "tdm", "dtx", V(0, 0, 1, 1, 1, 0)),
> MPP_VAR_FUNCTION(0x3, "ge1", "txctl", V(0, 1, 1, 1, 1, 0)),
> MPP_VAR_FUNCTION(0xb, "lcd", "d13", V(0, 0, 0, 0, 1, 0))),
> MPP_MODE(34,
>
> It is output only.
Oops, Sorry for the noise!
>
> I actually had the opposite bug in v1, setup two gpo's as gpio's.
>
> Andrew
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
2014-02-06 16:38 ` Arnd Bergmann
@ 2014-02-06 17:03 ` Andrew Lunn
[not found] ` <20140206170333.GK29860-g2DYL2Zd6BY@public.gmane.org>
0 siblings, 1 reply; 12+ messages in thread
From: Andrew Lunn @ 2014-02-06 17:03 UTC (permalink / raw)
To: Arnd Bergmann
Cc: Mark Rutland, Andrew Lunn, Ben Peddell, Jason Cooper, pawel.moll,
devicetree, Ian Campbell, Kumar Gala, linux-arm-kernel
On Thu, Feb 06, 2014 at 05:38:28PM +0100, Arnd Bergmann wrote:
> On Thursday 06 February 2014 17:01:26 Andrew Lunn wrote:
>
> > , but this is, imho,
> > > over-fragmenting. I'm sure there's a reason you chose this path, but
> > > you haven't explained why in your commit log. So I'm left guessing...
> >
> > Synology seem to build there devices like lego. They have two
> > different RTC blocks. They have three different fan alarm blocks, four
> > different led blocks, etc. And to build a product, the just select a
> > group of blocks and put them together.
>
> I guess the Armada-370 and newer based ds213j and dsx14 will also be
> able to reuse some of the blocks, right?
Hi Arnd
I've not looked at any sources for those yet. I guess the RTC .dtsi
files should be reusable. The ethernet driver on 370 is different so
no re-use there. Maybe the fan controller, but the rest will depend on
what GPIO lines they have used, if they are compatible.
Andrew
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
[not found] ` <20140206170333.GK29860-g2DYL2Zd6BY@public.gmane.org>
@ 2014-02-06 17:26 ` Jason Cooper
0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-02-06 17:26 UTC (permalink / raw)
To: Andrew Lunn
Cc: Arnd Bergmann, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Mark Rutland, Ben Peddell, pawel.moll-5wv7dgnIgG8,
devicetree-u79uwXL29TY76Z2rM5mHXA, Kumar Gala, Ian Campbell
On Thu, Feb 06, 2014 at 06:03:33PM +0100, Andrew Lunn wrote:
> On Thu, Feb 06, 2014 at 05:38:28PM +0100, Arnd Bergmann wrote:
> > On Thursday 06 February 2014 17:01:26 Andrew Lunn wrote:
> >
> > > , but this is, imho,
> > > > over-fragmenting. I'm sure there's a reason you chose this path, but
> > > > you haven't explained why in your commit log. So I'm left guessing...
> > >
> > > Synology seem to build there devices like lego. They have two
> > > different RTC blocks. They have three different fan alarm blocks, four
> > > different led blocks, etc. And to build a product, the just select a
> > > group of blocks and put them together.
> >
> > I guess the Armada-370 and newer based ds213j and dsx14 will also be
> > able to reuse some of the blocks, right?
>
> Hi Arnd
>
> I've not looked at any sources for those yet. I guess the RTC .dtsi
> files should be reusable. The ethernet driver on 370 is different so
> no re-use there. Maybe the fan controller, but the rest will depend on
> what GPIO lines they have used, if they are compatible.
perhaps all of the pinctrl nodes should be moved into synology-6281,
synology-6282, and synology-370 ?
thx,
Jason.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
[not found] ` <20140206160126.GH29860-g2DYL2Zd6BY@public.gmane.org>
@ 2014-02-07 7:44 ` Ben Peddell
2014-02-10 11:41 ` Ian Campbell
1 sibling, 0 replies; 12+ messages in thread
From: Ben Peddell @ 2014-02-07 7:44 UTC (permalink / raw)
To: Andrew Lunn, Jason Cooper
Cc: linux ARM, devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
pawel.moll-5wv7dgnIgG8, Mark Rutland, Ian Campbell, Kumar Gala
On 7/02/2014 2:01 AM, Andrew Lunn wrote:
> On Thu, Feb 06, 2014 at 10:39:39AM -0500, Jason Cooper wrote:
>>
>> + devicetree ML, DT maintainers
>>
>> On Wed, Feb 05, 2014 at 10:05:09PM +0100, Andrew Lunn wrote:
>>> Add device tree fragments and files to support many of the kirkwood
>>> based Synology NAS devices. This is a translation of the board setup
>>> file maintained by Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
>>>
>>> Signed-off-by: Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>
>>> Tested by Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
>>> cc: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
>>> ---
>>>
>>> v2:
>>> Fix gpio's which should be gpo.
>>> Rebase onto v3-14-rc1
>>> Update RTC nodes with vendor name.
>>> Update SPI flash node with vendor name.
>>> ---
>>> arch/arm/boot/dts/Makefile | 15 ++++
>>> arch/arm/boot/dts/kirkwood-ds109.dts | 33 +++++++
>>> arch/arm/boot/dts/kirkwood-ds110jv10.dts | 33 +++++++
>>> arch/arm/boot/dts/kirkwood-ds111.dts | 33 +++++++
>>> arch/arm/boot/dts/kirkwood-ds112.dts | 34 +++++++
>>> arch/arm/boot/dts/kirkwood-ds209.dts | 33 +++++++
>>> arch/arm/boot/dts/kirkwood-ds210.dts | 35 ++++++++
>>> arch/arm/boot/dts/kirkwood-ds212.dts | 37 ++++++++
>>> arch/arm/boot/dts/kirkwood-ds212j.dts | 34 +++++++
>>> arch/arm/boot/dts/kirkwood-ds409.dts | 34 +++++++
>>> arch/arm/boot/dts/kirkwood-ds409slim.dts | 32 +++++++
>>> arch/arm/boot/dts/kirkwood-ds411.dts | 35 ++++++++
>>> arch/arm/boot/dts/kirkwood-ds411j.dts | 34 +++++++
>>> arch/arm/boot/dts/kirkwood-ds411slim.dts | 34 +++++++
>>> arch/arm/boot/dts/kirkwood-rs212.dts | 34 +++++++
>>> arch/arm/boot/dts/kirkwood-rs409.dts | 33 +++++++
>>> arch/arm/boot/dts/kirkwood-rs411.dts | 34 +++++++
>>> arch/arm/boot/dts/synology/alarm-led-12.dtsi | 28 ++++++
>>> arch/arm/boot/dts/synology/common.dtsi | 112 ++++++++++++++++++++++++
>>> arch/arm/boot/dts/synology/ethernet-1.dtsi | 15 ++++
>>> arch/arm/boot/dts/synology/fan-alarm-18.dtsi | 22 +++++
>>> arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi | 22 +++++
>>> arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi | 32 +++++++
>>> arch/arm/boot/dts/synology/fan-gpios-15.dtsi | 34 +++++++
>>> arch/arm/boot/dts/synology/fan-gpios-32.dtsi | 34 +++++++
>>> arch/arm/boot/dts/synology/fan-speed-100.dtsi | 20 +++++
>>> arch/arm/boot/dts/synology/fan-speed-120.dtsi | 20 +++++
>>> arch/arm/boot/dts/synology/fan-speed-150.dtsi | 20 +++++
>>> arch/arm/boot/dts/synology/hdd-leds-20.dtsi | 90 +++++++++++++++++++
>>> arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi | 36 ++++++++
>>> arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi | 52 +++++++++++
>>> arch/arm/boot/dts/synology/hdd-leds-36.dtsi | 103 ++++++++++++++++++++++
>>> arch/arm/boot/dts/synology/hdd-leds-38.dtsi | 52 +++++++++++
>>> arch/arm/boot/dts/synology/hdd-power-29.dtsi | 56 ++++++++++++
>>> arch/arm/boot/dts/synology/hdd-power-30-1.dtsi | 40 +++++++++
>>> arch/arm/boot/dts/synology/hdd-power-30-2.dtsi | 56 ++++++++++++
>>> arch/arm/boot/dts/synology/hdd-power-30-4.dtsi | 89 +++++++++++++++++++
>>> arch/arm/boot/dts/synology/hdd-power-31.dtsi | 40 +++++++++
>>> arch/arm/boot/dts/synology/hdd-power-34.dtsi | 73 +++++++++++++++
>>> arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi | 18 ++++
>>> arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi | 18 ++++
>>> arch/arm/boot/dts/synology/pcie-2.dtsi | 19 ++++
>>> 42 files changed, 1658 insertions(+)
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts
>>> create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts
>>> create mode 100644 arch/arm/boot/dts/synology/alarm-led-12.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/common.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/ethernet-1.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/fan-alarm-18.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/fan-alarm-35-1.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/fan-alarm-35-3.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/fan-gpios-15.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/fan-gpios-32.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/fan-speed-100.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/fan-speed-120.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/fan-speed-150.dtsi
If we're not worried about the non-linearity of the 150R+120R+100R and
182R+150R+100R fan controllers (vs the 150R/100R/33R ones), these fan
speed blocks could be collapsed into common.dtsi.
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-20.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-21-1.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-21-2.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-36.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-leds-38.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-power-29.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-1.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-2.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-power-30-4.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-power-31.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/hdd-power-34.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/i2c-rtc-ricoh.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/i2c-rtc-seiko.dtsi
>>> create mode 100644 arch/arm/boot/dts/synology/pcie-2.dtsi
>>
>> Holy sh*t! I know we're adding 15 boards
>
> More than 15 actually. Most .dts files support multiple devices. So
> there should be about 30 devices supported by these .dts files.
>
>> , but this is, imho,
>> over-fragmenting. I'm sure there's a reason you chose this path, but
>> you haven't explained why in your commit log. So I'm left guessing...
>
> Synology seem to build there devices like lego. They have two
> different RTC blocks. They have three different fan alarm blocks, four
> different led blocks, etc. And to build a product, the just select a
> group of blocks and put them together.
The Ricoh RTC seems to be only used in the pre-2010 units. Everything
else uses the Seiko RTC.
Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed
with the built-in SATA interface activity/presence pins on mpp 20-23,
while the 4-bay units use ge01 and a PCIe SATA controller, and put the
software controlled HDD leds on mpp 36-43.
Most of the 6281 units with HDD power controls use mpp 29 and 31, while
most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45
and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and
4-bay units didn't have a separate power control for HDD1. These power
controls are presumably to limit startup current from the 12V brick
power supply.
From
http://forum.synology.com/wiki/index.php/What_kind_of_CPU_does_my_NAS_have,
it doesn't look like there are any new 6281 or 6282 models for 2014.
>
> The board setup code which Ben Peddell wrote has a somewhat similar
> structure:
>
> http://klightspeed.killerwolves.net/synology/linux-3.4-synology-0.1.patch
A more up-to-date version is at:
http://klightspeed.killerwolves.net/synology/linux-3.7-synology-0.2.patch
>
> It has a set of functions which add platform devices. And a table
> driven piece of code which based on the product name calls these
> functions to add the needed platform devices. Take a look at the table
> to get a better idea of the re-use factor of the blocks.
>
> In this DT version, i have a dtsi file for each function, and a dti
> file for each table entry.
>
> I will add to the changelog in the next version.
--
Ben Peddell
IT Support Bowen, Collinsville and Proserpine Catholic schools
http://klightspeed.killerwolves.net/
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices
[not found] ` <20140206160126.GH29860-g2DYL2Zd6BY@public.gmane.org>
2014-02-07 7:44 ` Ben Peddell
@ 2014-02-10 11:41 ` Ian Campbell
1 sibling, 0 replies; 12+ messages in thread
From: Ian Campbell @ 2014-02-10 11:41 UTC (permalink / raw)
To: Andrew Lunn
Cc: Jason Cooper, linux ARM, Ben Peddell,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
pawel.moll-5wv7dgnIgG8, Mark Rutland, Kumar Gala
On Thu, 2014-02-06 at 17:01 +0100, Andrew Lunn wrote:
> Synology seem to build there devices like lego. They have two
> different RTC blocks. They have three different fan alarm blocks, four
> different led blocks, etc. And to build a product, the just select a
> group of blocks and put them together.
>
> The board setup code which Ben Peddell wrote has a somewhat similar
> structure:
>
> http://klightspeed.killerwolves.net/synology/linux-3.4-synology-0.1.patch
>
> It has a set of functions which add platform devices. And a table
> driven piece of code which based on the product name calls these
> functions to add the needed platform devices. Take a look at the table
> to get a better idea of the re-use factor of the blocks.
>
> In this DT version, i have a dtsi file for each function, and a dti
> file for each table entry.
At least some other platforms deal with this by having a baseline dtsi
where most things have status="disabled" and then a per-board .dts file
which contains status="okay" and perhaps any specific pin bindings etc.
See arch/arm/boot/dts/sun?i* for an example of this approach.
Ian.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2014-02-10 11:41 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1391634309-3123-1-git-send-email-andrew@lunn.ch>
[not found] ` <1391634309-3123-3-git-send-email-andrew@lunn.ch>
[not found] ` <1391634309-3123-3-git-send-email-andrew-g2DYL2Zd6BY@public.gmane.org>
2014-02-06 15:19 ` [PATCH 2/4] DT: Vendor prefixes: Add ricoh, ssi and synology Jason Cooper
[not found] ` <1391634309-3123-4-git-send-email-andrew@lunn.ch>
[not found] ` <1391634309-3123-4-git-send-email-andrew-g2DYL2Zd6BY@public.gmane.org>
2014-02-06 15:21 ` [PATCH 3/4] DT: i2c: Trivial: Add sii,s35390a Jason Cooper
[not found] ` <1391634309-3123-5-git-send-email-andrew@lunn.ch>
2014-02-06 15:39 ` [PATCH 4/4] ARM: Kirkwood: Add support for many Synology NAS devices Jason Cooper
2014-02-06 16:01 ` Andrew Lunn
2014-02-06 16:38 ` Arnd Bergmann
2014-02-06 17:03 ` Andrew Lunn
[not found] ` <20140206170333.GK29860-g2DYL2Zd6BY@public.gmane.org>
2014-02-06 17:26 ` Jason Cooper
[not found] ` <20140206160126.GH29860-g2DYL2Zd6BY@public.gmane.org>
2014-02-07 7:44 ` Ben Peddell
2014-02-10 11:41 ` Ian Campbell
2014-02-06 16:39 ` Ian Campbell
[not found] ` <1391704765.2162.7.camel-ommiHX4a84BXesXXhkcM7miJhflN2719@public.gmane.org>
2014-02-06 16:50 ` Andrew Lunn
2014-02-06 16:52 ` Ian Campbell
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).