* [PATCH v4] mmc: implement Driver Stage Register handling
@ 2014-08-15 8:38 Uwe Kleine-König
2014-08-15 9:05 ` Ulf Hansson
0 siblings, 1 reply; 3+ messages in thread
From: Uwe Kleine-König @ 2014-08-15 8:38 UTC (permalink / raw)
To: Chris Ball, Ulf Hansson
Cc: linux-mmc, kernel, Markus Niebel, linux-arm-kernel, devicetree,
Sascha Hauer
From: Sascha Hauer <s.hauer@pengutronix.de>
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
Changes since v3:
- fix a compiler warning about err not being used.
- clearified valid range. I didn't write "16-bit value" because the
value is still expected to be written as 32-bit value in the device
tree.
- make host->dsr an u32, which simplified parsing the device tree and
also makes casting in mmc_set_dsr unnecessary.
---
Documentation/devicetree/bindings/mmc/mmc.txt | 2 ++
drivers/mmc/core/host.c | 8 ++++++++
drivers/mmc/core/mmc.c | 8 ++++++++
drivers/mmc/core/mmc_ops.c | 20 ++++++++++++++++++++
drivers/mmc/core/mmc_ops.h | 1 +
drivers/mmc/core/sd.c | 8 ++++++++
include/linux/mmc/card.h | 3 ++-
include/linux/mmc/host.h | 3 +++
8 files changed, 52 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index 3c18001dfd5d..a3fe21f2b709 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -40,6 +40,8 @@ Optional properties:
- mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported
- mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported
- mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported
+- dsr: Value the card's (optional) Driver Stage Register (DSR) should be
+ programmed with. Valid range: [0 .. 0xffff].
*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
polarity properties, we have to fix the meaning of the "normal" and "inverted"
diff --git a/drivers/mmc/core/host.c b/drivers/mmc/core/host.c
index 95cceae96944..6442eecb672e 100644
--- a/drivers/mmc/core/host.c
+++ b/drivers/mmc/core/host.c
@@ -452,6 +452,14 @@ int mmc_of_parse(struct mmc_host *host)
if (of_find_property(np, "mmc-hs400-1_2v", &len))
host->caps2 |= MMC_CAP2_HS400_1_2V | MMC_CAP2_HS200_1_2V_SDR;
+ host->dsr_req = of_property_read_u32(np, "dsr", &host->dsr);
+ if (host->dsr_req && (host->dsr & ~0xffff)) {
+ dev_err(host->parent,
+ "device tree specified broken value for DSR: 0x%x, ignoring\n",
+ host->dsr);
+ host->dsr_req = 0;
+ }
+
return 0;
out:
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index 793c6f7ddb04..fdc1ac1360c4 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -162,6 +162,7 @@ static int mmc_decode_csd(struct mmc_card *card)
csd->read_partial = UNSTUFF_BITS(resp, 79, 1);
csd->write_misalign = UNSTUFF_BITS(resp, 78, 1);
csd->read_misalign = UNSTUFF_BITS(resp, 77, 1);
+ csd->dsr_imp = UNSTUFF_BITS(resp, 76, 1);
csd->r2w_factor = UNSTUFF_BITS(resp, 26, 3);
csd->write_blkbits = UNSTUFF_BITS(resp, 22, 4);
csd->write_partial = UNSTUFF_BITS(resp, 21, 1);
@@ -1273,6 +1274,13 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
}
/*
+ * handling only for cards supporting DSR and hosts requesting
+ * DSR configuration
+ */
+ if (card->csd.dsr_imp && host->dsr_req)
+ mmc_set_dsr(host);
+
+ /*
* Select card, as all following commands rely on that.
*/
if (!mmc_host_is_spi(host)) {
diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
index f51b5ba3bbea..ba0275e90617 100644
--- a/drivers/mmc/core/mmc_ops.c
+++ b/drivers/mmc/core/mmc_ops.c
@@ -93,6 +93,26 @@ int mmc_deselect_cards(struct mmc_host *host)
return _mmc_select_card(host, NULL);
}
+/*
+ * Write the value specified in the device tree or board code into the optional
+ * 16 bit Driver Stage Register. This can be used to tune raise/fall times and
+ * drive strength of the DAT and CMD outputs. The actual meaning of a given
+ * value is hardware dependant.
+ * The presence of the DSR register can be determined from the CSD register,
+ * bit 76.
+ */
+int mmc_set_dsr(struct mmc_host *host)
+{
+ struct mmc_command cmd = {0};
+
+ cmd.opcode = MMC_SET_DSR;
+
+ cmd.arg = (host->dsr << 16) | 0xffff;
+ cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
+
+ return mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
+}
+
int mmc_go_idle(struct mmc_host *host)
{
int err;
diff --git a/drivers/mmc/core/mmc_ops.h b/drivers/mmc/core/mmc_ops.h
index 80ae9f4e0293..390dac665b2a 100644
--- a/drivers/mmc/core/mmc_ops.h
+++ b/drivers/mmc/core/mmc_ops.h
@@ -14,6 +14,7 @@
int mmc_select_card(struct mmc_card *card);
int mmc_deselect_cards(struct mmc_host *host);
+int mmc_set_dsr(struct mmc_host *host);
int mmc_go_idle(struct mmc_host *host);
int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr);
int mmc_all_send_cid(struct mmc_host *host, u32 *cid);
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 0c44510bf717..25913889cbaa 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -127,6 +127,7 @@ static int mmc_decode_csd(struct mmc_card *card)
csd->read_partial = UNSTUFF_BITS(resp, 79, 1);
csd->write_misalign = UNSTUFF_BITS(resp, 78, 1);
csd->read_misalign = UNSTUFF_BITS(resp, 77, 1);
+ csd->dsr_imp = UNSTUFF_BITS(resp, 76, 1);
csd->r2w_factor = UNSTUFF_BITS(resp, 26, 3);
csd->write_blkbits = UNSTUFF_BITS(resp, 22, 4);
csd->write_partial = UNSTUFF_BITS(resp, 21, 1);
@@ -954,6 +955,13 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
}
/*
+ * handling only for cards supporting DSR and hosts requesting
+ * DSR configuration
+ */
+ if (card->csd.dsr_imp && host->dsr_req)
+ mmc_set_dsr(host);
+
+ /*
* Select card, as all following commands rely on that.
*/
if (!mmc_host_is_spi(host)) {
diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index d424b9de3aff..680a7f0188bb 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -42,7 +42,8 @@ struct mmc_csd {
unsigned int read_partial:1,
read_misalign:1,
write_partial:1,
- write_misalign:1;
+ write_misalign:1,
+ dsr_imp:1;
};
struct mmc_ext_csd {
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 7960424d0bc0..8acaebd866a7 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -319,6 +319,7 @@ struct mmc_host {
#ifdef CONFIG_MMC_DEBUG
unsigned int removed:1; /* host is being removed */
#endif
+ unsigned int dsr_req:1; /* DSR is requested for Host */
int rescan_disable; /* disable card detection */
int rescan_entered; /* used with nonremovable devices */
@@ -365,6 +366,8 @@ struct mmc_host {
unsigned int slotno; /* used for sdio acpi binding */
+ u32 dsr; /* optional driver stage (DSR) value */
+
unsigned long private[0] ____cacheline_aligned;
};
--
2.0.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v4] mmc: implement Driver Stage Register handling
2014-08-15 8:38 [PATCH v4] mmc: implement Driver Stage Register handling Uwe Kleine-König
@ 2014-08-15 9:05 ` Ulf Hansson
2014-08-15 18:42 ` Uwe Kleine-König
0 siblings, 1 reply; 3+ messages in thread
From: Ulf Hansson @ 2014-08-15 9:05 UTC (permalink / raw)
To: Uwe Kleine-König
Cc: Chris Ball, linux-mmc, Sascha Hauer, Markus Niebel,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
Sascha Hauer
On 15 August 2014 10:38, Uwe Kleine-König
<u.kleine-koenig@pengutronix.de> wrote:
> From: Sascha Hauer <s.hauer@pengutronix.de>
>
> Some eMMC and SD cards implement a DSR register that allows to tune
> raise/fall times and drive strength of the CMD and DATA outputs.
> The values to use depend on the card in use and the host.
> It might be needed to reduce the drive strength to prevent voltage peaks
> above the host's specification.
>
> Implement a 'dsr' devicetree property that allows to specify the value
> to set the DSR to. For non-dt setups the new members of mmc_host can be
> set by board code.
>
> This patch was initially authored by Sascha Hauer. It contains
> improvements authored by Markus Niebel and Uwe Kleine-König.
>
> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> ---
> Changes since v3:
>
> - fix a compiler warning about err not being used.
> - clearified valid range. I didn't write "16-bit value" because the
> value is still expected to be written as 32-bit value in the device
> tree.
> - make host->dsr an u32, which simplified parsing the device tree and
> also makes casting in mmc_set_dsr unnecessary.
> ---
> Documentation/devicetree/bindings/mmc/mmc.txt | 2 ++
> drivers/mmc/core/host.c | 8 ++++++++
> drivers/mmc/core/mmc.c | 8 ++++++++
> drivers/mmc/core/mmc_ops.c | 20 ++++++++++++++++++++
> drivers/mmc/core/mmc_ops.h | 1 +
> drivers/mmc/core/sd.c | 8 ++++++++
> include/linux/mmc/card.h | 3 ++-
> include/linux/mmc/host.h | 3 +++
> 8 files changed, 52 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
> index 3c18001dfd5d..a3fe21f2b709 100644
> --- a/Documentation/devicetree/bindings/mmc/mmc.txt
> +++ b/Documentation/devicetree/bindings/mmc/mmc.txt
> @@ -40,6 +40,8 @@ Optional properties:
> - mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported
> - mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported
> - mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported
> +- dsr: Value the card's (optional) Driver Stage Register (DSR) should be
> + programmed with. Valid range: [0 .. 0xffff].
>
> *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
> polarity properties, we have to fix the meaning of the "normal" and "inverted"
> diff --git a/drivers/mmc/core/host.c b/drivers/mmc/core/host.c
> index 95cceae96944..6442eecb672e 100644
> --- a/drivers/mmc/core/host.c
> +++ b/drivers/mmc/core/host.c
> @@ -452,6 +452,14 @@ int mmc_of_parse(struct mmc_host *host)
> if (of_find_property(np, "mmc-hs400-1_2v", &len))
> host->caps2 |= MMC_CAP2_HS400_1_2V | MMC_CAP2_HS200_1_2V_SDR;
>
> + host->dsr_req = of_property_read_u32(np, "dsr", &host->dsr);
> + if (host->dsr_req && (host->dsr & ~0xffff)) {
This doesn't look correct.
I guess what you want is: if (!host->dsr_req && (host->dsr & ~0xffff))
> + dev_err(host->parent,
> + "device tree specified broken value for DSR: 0x%x, ignoring\n",
> + host->dsr);
> + host->dsr_req = 0;
> + }
> +
> return 0;
>
> out:
> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
> index 793c6f7ddb04..fdc1ac1360c4 100644
> --- a/drivers/mmc/core/mmc.c
> +++ b/drivers/mmc/core/mmc.c
> @@ -162,6 +162,7 @@ static int mmc_decode_csd(struct mmc_card *card)
> csd->read_partial = UNSTUFF_BITS(resp, 79, 1);
> csd->write_misalign = UNSTUFF_BITS(resp, 78, 1);
> csd->read_misalign = UNSTUFF_BITS(resp, 77, 1);
> + csd->dsr_imp = UNSTUFF_BITS(resp, 76, 1);
> csd->r2w_factor = UNSTUFF_BITS(resp, 26, 3);
> csd->write_blkbits = UNSTUFF_BITS(resp, 22, 4);
> csd->write_partial = UNSTUFF_BITS(resp, 21, 1);
> @@ -1273,6 +1274,13 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> }
>
> /*
> + * handling only for cards supporting DSR and hosts requesting
> + * DSR configuration
> + */
> + if (card->csd.dsr_imp && host->dsr_req)
if (card->csd.dsr_imp && !host->dsr_req)
> + mmc_set_dsr(host);
> +
> + /*
> * Select card, as all following commands rely on that.
> */
> if (!mmc_host_is_spi(host)) {
> diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
> index f51b5ba3bbea..ba0275e90617 100644
> --- a/drivers/mmc/core/mmc_ops.c
> +++ b/drivers/mmc/core/mmc_ops.c
> @@ -93,6 +93,26 @@ int mmc_deselect_cards(struct mmc_host *host)
> return _mmc_select_card(host, NULL);
> }
>
> +/*
> + * Write the value specified in the device tree or board code into the optional
> + * 16 bit Driver Stage Register. This can be used to tune raise/fall times and
> + * drive strength of the DAT and CMD outputs. The actual meaning of a given
> + * value is hardware dependant.
> + * The presence of the DSR register can be determined from the CSD register,
> + * bit 76.
> + */
> +int mmc_set_dsr(struct mmc_host *host)
> +{
> + struct mmc_command cmd = {0};
> +
> + cmd.opcode = MMC_SET_DSR;
> +
> + cmd.arg = (host->dsr << 16) | 0xffff;
> + cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
> +
> + return mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
> +}
> +
> int mmc_go_idle(struct mmc_host *host)
> {
> int err;
> diff --git a/drivers/mmc/core/mmc_ops.h b/drivers/mmc/core/mmc_ops.h
> index 80ae9f4e0293..390dac665b2a 100644
> --- a/drivers/mmc/core/mmc_ops.h
> +++ b/drivers/mmc/core/mmc_ops.h
> @@ -14,6 +14,7 @@
>
> int mmc_select_card(struct mmc_card *card);
> int mmc_deselect_cards(struct mmc_host *host);
> +int mmc_set_dsr(struct mmc_host *host);
> int mmc_go_idle(struct mmc_host *host);
> int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr);
> int mmc_all_send_cid(struct mmc_host *host, u32 *cid);
> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
> index 0c44510bf717..25913889cbaa 100644
> --- a/drivers/mmc/core/sd.c
> +++ b/drivers/mmc/core/sd.c
> @@ -127,6 +127,7 @@ static int mmc_decode_csd(struct mmc_card *card)
> csd->read_partial = UNSTUFF_BITS(resp, 79, 1);
> csd->write_misalign = UNSTUFF_BITS(resp, 78, 1);
> csd->read_misalign = UNSTUFF_BITS(resp, 77, 1);
> + csd->dsr_imp = UNSTUFF_BITS(resp, 76, 1);
> csd->r2w_factor = UNSTUFF_BITS(resp, 26, 3);
> csd->write_blkbits = UNSTUFF_BITS(resp, 22, 4);
> csd->write_partial = UNSTUFF_BITS(resp, 21, 1);
> @@ -954,6 +955,13 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
> }
>
> /*
> + * handling only for cards supporting DSR and hosts requesting
> + * DSR configuration
> + */
> + if (card->csd.dsr_imp && host->dsr_req)
if (card->csd.dsr_imp && !host->dsr_req)
> + mmc_set_dsr(host);
> +
> + /*
> * Select card, as all following commands rely on that.
> */
> if (!mmc_host_is_spi(host)) {
> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> index d424b9de3aff..680a7f0188bb 100644
> --- a/include/linux/mmc/card.h
> +++ b/include/linux/mmc/card.h
> @@ -42,7 +42,8 @@ struct mmc_csd {
> unsigned int read_partial:1,
> read_misalign:1,
> write_partial:1,
> - write_misalign:1;
> + write_misalign:1,
> + dsr_imp:1;
> };
>
> struct mmc_ext_csd {
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index 7960424d0bc0..8acaebd866a7 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -319,6 +319,7 @@ struct mmc_host {
> #ifdef CONFIG_MMC_DEBUG
> unsigned int removed:1; /* host is being removed */
> #endif
> + unsigned int dsr_req:1; /* DSR is requested for Host */
Should be an int instead.
>
> int rescan_disable; /* disable card detection */
> int rescan_entered; /* used with nonremovable devices */
> @@ -365,6 +366,8 @@ struct mmc_host {
>
> unsigned int slotno; /* used for sdio acpi binding */
>
> + u32 dsr; /* optional driver stage (DSR) value */
> +
> unsigned long private[0] ____cacheline_aligned;
> };
>
> --
> 2.0.1
>
Kind regards
Uffe
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v4] mmc: implement Driver Stage Register handling
2014-08-15 9:05 ` Ulf Hansson
@ 2014-08-15 18:42 ` Uwe Kleine-König
0 siblings, 0 replies; 3+ messages in thread
From: Uwe Kleine-König @ 2014-08-15 18:42 UTC (permalink / raw)
To: Ulf Hansson
Cc: Chris Ball, linux-mmc, Sascha Hauer, Markus Niebel,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
Sascha Hauer
Hello Ulf,
On Fri, Aug 15, 2014 at 11:05:39AM +0200, Ulf Hansson wrote:
> On 15 August 2014 10:38, Uwe Kleine-König
> <u.kleine-koenig@pengutronix.de> wrote:
> > From: Sascha Hauer <s.hauer@pengutronix.de>
> >
> > Some eMMC and SD cards implement a DSR register that allows to tune
> > raise/fall times and drive strength of the CMD and DATA outputs.
> > The values to use depend on the card in use and the host.
> > It might be needed to reduce the drive strength to prevent voltage peaks
> > above the host's specification.
> >
> > Implement a 'dsr' devicetree property that allows to specify the value
> > to set the DSR to. For non-dt setups the new members of mmc_host can be
> > set by board code.
> >
> > This patch was initially authored by Sascha Hauer. It contains
> > improvements authored by Markus Niebel and Uwe Kleine-König.
> >
> > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> > Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
> > Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> > ---
> > Changes since v3:
> >
> > - fix a compiler warning about err not being used.
> > - clearified valid range. I didn't write "16-bit value" because the
> > value is still expected to be written as 32-bit value in the device
> > tree.
> > - make host->dsr an u32, which simplified parsing the device tree and
> > also makes casting in mmc_set_dsr unnecessary.
> > ---
> > Documentation/devicetree/bindings/mmc/mmc.txt | 2 ++
> > drivers/mmc/core/host.c | 8 ++++++++
> > drivers/mmc/core/mmc.c | 8 ++++++++
> > drivers/mmc/core/mmc_ops.c | 20 ++++++++++++++++++++
> > drivers/mmc/core/mmc_ops.h | 1 +
> > drivers/mmc/core/sd.c | 8 ++++++++
> > include/linux/mmc/card.h | 3 ++-
> > include/linux/mmc/host.h | 3 +++
> > 8 files changed, 52 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
> > index 3c18001dfd5d..a3fe21f2b709 100644
> > --- a/Documentation/devicetree/bindings/mmc/mmc.txt
> > +++ b/Documentation/devicetree/bindings/mmc/mmc.txt
> > @@ -40,6 +40,8 @@ Optional properties:
> > - mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported
> > - mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported
> > - mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported
> > +- dsr: Value the card's (optional) Driver Stage Register (DSR) should be
> > + programmed with. Valid range: [0 .. 0xffff].
> >
> > *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
> > polarity properties, we have to fix the meaning of the "normal" and "inverted"
> > diff --git a/drivers/mmc/core/host.c b/drivers/mmc/core/host.c
> > index 95cceae96944..6442eecb672e 100644
> > --- a/drivers/mmc/core/host.c
> > +++ b/drivers/mmc/core/host.c
> > @@ -452,6 +452,14 @@ int mmc_of_parse(struct mmc_host *host)
> > if (of_find_property(np, "mmc-hs400-1_2v", &len))
> > host->caps2 |= MMC_CAP2_HS400_1_2V | MMC_CAP2_HS200_1_2V_SDR;
> >
> > + host->dsr_req = of_property_read_u32(np, "dsr", &host->dsr);
> > + if (host->dsr_req && (host->dsr & ~0xffff)) {
>
> This doesn't look correct.
> I guess what you want is: if (!host->dsr_req && (host->dsr & ~0xffff))
Ah, you're right. I thought that of_property_read_u32 returned true if
it worked and false if not. But it returns 0 for success and -ESOMETHING
otherwise.
So I want host->dsr_req = !of_property_read_u32(np, "dsr", &host->dsr);
I now have some working hardware again, will test again and send an v5.
>
> > + dev_err(host->parent,
> > + "device tree specified broken value for DSR: 0x%x, ignoring\n",
> > + host->dsr);
> > + host->dsr_req = 0;
> > + }
> > +
> > return 0;
> >
> > out:
> > diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
> > index 793c6f7ddb04..fdc1ac1360c4 100644
> > --- a/drivers/mmc/core/mmc.c
> > +++ b/drivers/mmc/core/mmc.c
> > @@ -162,6 +162,7 @@ static int mmc_decode_csd(struct mmc_card *card)
> > csd->read_partial = UNSTUFF_BITS(resp, 79, 1);
> > csd->write_misalign = UNSTUFF_BITS(resp, 78, 1);
> > csd->read_misalign = UNSTUFF_BITS(resp, 77, 1);
> > + csd->dsr_imp = UNSTUFF_BITS(resp, 76, 1);
> > csd->r2w_factor = UNSTUFF_BITS(resp, 26, 3);
> > csd->write_blkbits = UNSTUFF_BITS(resp, 22, 4);
> > csd->write_partial = UNSTUFF_BITS(resp, 21, 1);
> > @@ -1273,6 +1274,13 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> > }
> >
> > /*
> > + * handling only for cards supporting DSR and hosts requesting
> > + * DSR configuration
> > + */
> > + if (card->csd.dsr_imp && host->dsr_req)
>
> if (card->csd.dsr_imp && !host->dsr_req)
With the above change my line is correct.
> > struct mmc_ext_csd {
> > diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> > index 7960424d0bc0..8acaebd866a7 100644
> > --- a/include/linux/mmc/host.h
> > +++ b/include/linux/mmc/host.h
> > @@ -319,6 +319,7 @@ struct mmc_host {
> > #ifdef CONFIG_MMC_DEBUG
> > unsigned int removed:1; /* host is being removed */
> > #endif
> > + unsigned int dsr_req:1; /* DSR is requested for Host */
>
> Should be an int instead.
I don't care much, can change to int.
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-08-15 18:42 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-08-15 8:38 [PATCH v4] mmc: implement Driver Stage Register handling Uwe Kleine-König
2014-08-15 9:05 ` Ulf Hansson
2014-08-15 18:42 ` Uwe Kleine-König
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).