* [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers
@ 2014-08-14 14:23 Vivek Gautam
2014-08-14 14:23 ` [PATCH 1/7] usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver Vivek Gautam
` (7 more replies)
0 siblings, 8 replies; 15+ messages in thread
From: Vivek Gautam @ 2014-08-14 14:23 UTC (permalink / raw)
To: linux-usb, balbi
Cc: linux-kernel, devicetree, grant.likely, gregkh, stern, jg1.han,
s.nawrocki, k.debski, Vivek Gautam
- This series is based on 'usb-next' branch.
Now that we have support for USB PHY controllers for Exynos SoC series,
we are free to remove the older usb-phy support.
In the process, we are removing the entire phy-samsung-usb3 driver, and
besides that all support for Exynos4x and Exynos5 from phy-samsung-usb2
driver.
We have also removed the older USB-PHY support from ehci-exynos and ohci-exynos
since those drivers now can use newer GENERIC-PHYs, and don't need the older
USB-PHYs and related code anymore. These patches for ohci-exynos and ehci-exynos
now replaces the older sent patch for phy sequence cleanup for them.[1]
I have build-tested this series for exynos_defconfig and s3c64xx_defconfig,
and have tested the EHCI and OHCI operations on smdk5250 board, but
have not tested the actual working due to unavailability of S3C64XX
board. So can someone please help me testing this series.
[1] https://lkml.org/lkml/2014/8/5/142
Vivek Gautam (7):
usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver
usb-phy: samsung-usb2: Remove support for Exynos5250
usb-phy: samsung-usb2: Remove support for Exynos4X12
usb-phy: samsung-usb2: Remove support for Exynos4210
usb-phy: samsung-usb2: Clean up to leave only S3C64XX support
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: host: ohci-exynos: Remove unnecessary usb-phy support
drivers/usb/host/ehci-exynos.c | 53 +-----
drivers/usb/host/ohci-exynos.c | 64 +------
drivers/usb/phy/Kconfig | 16 --
drivers/usb/phy/Makefile | 2 -
drivers/usb/phy/phy-samsung-usb.c | 241 -----------------------
drivers/usb/phy/phy-samsung-usb.h | 349 ---------------------------------
drivers/usb/phy/phy-samsung-usb2.c | 371 ++++++++----------------------------
drivers/usb/phy/phy-samsung-usb2.h | 121 ++++++++++++
drivers/usb/phy/phy-samsung-usb3.c | 350 ----------------------------------
9 files changed, 213 insertions(+), 1354 deletions(-)
delete mode 100644 drivers/usb/phy/phy-samsung-usb.c
delete mode 100644 drivers/usb/phy/phy-samsung-usb.h
create mode 100644 drivers/usb/phy/phy-samsung-usb2.h
delete mode 100644 drivers/usb/phy/phy-samsung-usb3.c
--
1.7.10.4
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 1/7] usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver
2014-08-14 14:23 [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Vivek Gautam
@ 2014-08-14 14:23 ` Vivek Gautam
2014-08-18 1:34 ` Jingoo Han
2014-08-14 14:23 ` [PATCH RFC 2/7] usb-phy: samsung-usb2: Remove support for Exynos5250 Vivek Gautam
` (6 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Vivek Gautam @ 2014-08-14 14:23 UTC (permalink / raw)
To: linux-usb, balbi
Cc: linux-kernel, devicetree, grant.likely, gregkh, stern, jg1.han,
s.nawrocki, k.debski, Vivek Gautam
Removing this older USB 3.0 DRD controller PHY driver, since
a new driver based on generic phy framework is now available.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
---
drivers/usb/phy/Kconfig | 8 -
drivers/usb/phy/Makefile | 1 -
drivers/usb/phy/phy-samsung-usb.h | 80 ---------
drivers/usb/phy/phy-samsung-usb3.c | 350 ------------------------------------
4 files changed, 439 deletions(-)
delete mode 100644 drivers/usb/phy/phy-samsung-usb3.c
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index e253fa0..751b594 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -86,14 +86,6 @@ config SAMSUNG_USB2PHY
Enable this to support Samsung USB 2.0 (High Speed) PHY controller
driver for Samsung SoCs.
-config SAMSUNG_USB3PHY
- tristate "Samsung USB 3.0 PHY controller Driver"
- select SAMSUNG_USBPHY
- select USB_PHY
- help
- Enable this to support Samsung USB 3.0 (Super Speed) phy controller
- for samsung SoCs.
-
config TWL6030_USB
tristate "TWL6030 USB Transceiver Driver"
depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index 24a9133..9c984dd 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -16,7 +16,6 @@ obj-$(CONFIG_AM335X_PHY_USB) += phy-am335x.o
obj-$(CONFIG_OMAP_OTG) += phy-omap-otg.o
obj-$(CONFIG_SAMSUNG_USBPHY) += phy-samsung-usb.o
obj-$(CONFIG_SAMSUNG_USB2PHY) += phy-samsung-usb2.o
-obj-$(CONFIG_SAMSUNG_USB3PHY) += phy-samsung-usb3.o
obj-$(CONFIG_TWL6030_USB) += phy-twl6030-usb.o
obj-$(CONFIG_USB_EHCI_TEGRA) += phy-tegra-usb.o
obj-$(CONFIG_USB_GPIO_VBUS) += phy-gpio-vbus-usb.o
diff --git a/drivers/usb/phy/phy-samsung-usb.h b/drivers/usb/phy/phy-samsung-usb.h
index 68771bf..dd2a0b5 100644
--- a/drivers/usb/phy/phy-samsung-usb.h
+++ b/drivers/usb/phy/phy-samsung-usb.h
@@ -155,86 +155,6 @@
#define EXYNOS5_PHY_OTG_TUNE (0x40)
-/* EXYNOS5: USB 3.0 DRD */
-#define EXYNOS5_DRD_LINKSYSTEM (0x04)
-
-#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
-#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
-#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
-
-#define EXYNOS5_DRD_PHYUTMI (0x08)
-
-#define PHYUTMI_OTGDISABLE (0x1 << 6)
-#define PHYUTMI_FORCESUSPEND (0x1 << 1)
-#define PHYUTMI_FORCESLEEP (0x1 << 0)
-
-#define EXYNOS5_DRD_PHYPIPE (0x0c)
-
-#define EXYNOS5_DRD_PHYCLKRST (0x10)
-
-#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
-#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
-
-#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
-#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
-
-#define PHYCLKRST_SSC_EN (0x1 << 20)
-#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
-#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
-
-#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x02 << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
-
-#define PHYCLKRST_FSEL_MASK (0x3f << 5)
-#define PHYCLKRST_FSEL(_x) ((_x) << 5)
-#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
-#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
-#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
-#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
-
-#define PHYCLKRST_RETENABLEN (0x1 << 4)
-
-#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
-#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
-#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
-
-#define PHYCLKRST_PORTRESET (0x1 << 1)
-#define PHYCLKRST_COMMONONN (0x1 << 0)
-
-#define EXYNOS5_DRD_PHYREG0 (0x14)
-#define EXYNOS5_DRD_PHYREG1 (0x18)
-
-#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
-
-#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
-#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
-#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
-
-#define EXYNOS5_DRD_PHYPARAM1 (0x20)
-
-#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
-#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
-
-#define EXYNOS5_DRD_PHYTERM (0x24)
-
-#define EXYNOS5_DRD_PHYTEST (0x28)
-
-#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
-#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
-
-#define EXYNOS5_DRD_PHYADP (0x2c)
-
-#define EXYNOS5_DRD_PHYBATCHG (0x30)
-
-#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
-
-#define EXYNOS5_DRD_PHYRESUME (0x34)
-#define EXYNOS5_DRD_LINKPORT (0x44)
-
#ifndef MHZ
#define MHZ (1000*1000)
#endif
diff --git a/drivers/usb/phy/phy-samsung-usb3.c b/drivers/usb/phy/phy-samsung-usb3.c
deleted file mode 100644
index cc08192..0000000
--- a/drivers/usb/phy/phy-samsung-usb3.c
+++ /dev/null
@@ -1,350 +0,0 @@
-/* linux/drivers/usb/phy/phy-samsung-usb3.c
- *
- * Copyright (c) 2013 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * Author: Vivek Gautam <gautam.vivek@samsung.com>
- *
- * Samsung USB 3.0 PHY transceiver; talks to DWC3 controller.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/usb/samsung_usb_phy.h>
-#include <linux/platform_data/samsung-usbphy.h>
-
-#include "phy-samsung-usb.h"
-
-/*
- * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
- */
-static u32 samsung_usb3phy_set_refclk(struct samsung_usbphy *sphy)
-{
- u32 reg;
- u32 refclk;
-
- refclk = sphy->ref_clk_freq;
-
- reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
- PHYCLKRST_FSEL(refclk);
-
- switch (refclk) {
- case FSEL_CLKSEL_50M:
- reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
- PHYCLKRST_SSC_REFCLKSEL(0x00));
- break;
- case FSEL_CLKSEL_20M:
- reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
- PHYCLKRST_SSC_REFCLKSEL(0x00));
- break;
- case FSEL_CLKSEL_19200K:
- reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
- PHYCLKRST_SSC_REFCLKSEL(0x88));
- break;
- case FSEL_CLKSEL_24M:
- default:
- reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
- PHYCLKRST_SSC_REFCLKSEL(0x88));
- break;
- }
-
- return reg;
-}
-
-static void samsung_exynos5_usb3phy_enable(struct samsung_usbphy *sphy)
-{
- void __iomem *regs = sphy->regs;
- u32 phyparam0;
- u32 phyparam1;
- u32 linksystem;
- u32 phybatchg;
- u32 phytest;
- u32 phyclkrst;
-
- /* Reset USB 3.0 PHY */
- writel(0x0, regs + EXYNOS5_DRD_PHYREG0);
-
- phyparam0 = readl(regs + EXYNOS5_DRD_PHYPARAM0);
- /* Select PHY CLK source */
- phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
- /* Set Loss-of-Signal Detector sensitivity */
- phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
- phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
- writel(phyparam0, regs + EXYNOS5_DRD_PHYPARAM0);
-
- writel(0x0, regs + EXYNOS5_DRD_PHYRESUME);
-
- /*
- * Setting the Frame length Adj value[6:1] to default 0x20
- * See xHCI 1.0 spec, 5.2.4
- */
- linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
- LINKSYSTEM_FLADJ(0x20);
- writel(linksystem, regs + EXYNOS5_DRD_LINKSYSTEM);
-
- phyparam1 = readl(regs + EXYNOS5_DRD_PHYPARAM1);
- /* Set Tx De-Emphasis level */
- phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
- phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
- writel(phyparam1, regs + EXYNOS5_DRD_PHYPARAM1);
-
- phybatchg = readl(regs + EXYNOS5_DRD_PHYBATCHG);
- phybatchg |= PHYBATCHG_UTMI_CLKSEL;
- writel(phybatchg, regs + EXYNOS5_DRD_PHYBATCHG);
-
- /* PHYTEST POWERDOWN Control */
- phytest = readl(regs + EXYNOS5_DRD_PHYTEST);
- phytest &= ~(PHYTEST_POWERDOWN_SSP |
- PHYTEST_POWERDOWN_HSP);
- writel(phytest, regs + EXYNOS5_DRD_PHYTEST);
-
- /* UTMI Power Control */
- writel(PHYUTMI_OTGDISABLE, regs + EXYNOS5_DRD_PHYUTMI);
-
- phyclkrst = samsung_usb3phy_set_refclk(sphy);
-
- phyclkrst |= PHYCLKRST_PORTRESET |
- /* Digital power supply in normal operating mode */
- PHYCLKRST_RETENABLEN |
- /* Enable ref clock for SS function */
- PHYCLKRST_REF_SSP_EN |
- /* Enable spread spectrum */
- PHYCLKRST_SSC_EN |
- /* Power down HS Bias and PLL blocks in suspend mode */
- PHYCLKRST_COMMONONN;
-
- writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
-
- udelay(10);
-
- phyclkrst &= ~(PHYCLKRST_PORTRESET);
- writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
-}
-
-static void samsung_exynos5_usb3phy_disable(struct samsung_usbphy *sphy)
-{
- u32 phyutmi;
- u32 phyclkrst;
- u32 phytest;
- void __iomem *regs = sphy->regs;
-
- phyutmi = PHYUTMI_OTGDISABLE |
- PHYUTMI_FORCESUSPEND |
- PHYUTMI_FORCESLEEP;
- writel(phyutmi, regs + EXYNOS5_DRD_PHYUTMI);
-
- /* Resetting the PHYCLKRST enable bits to reduce leakage current */
- phyclkrst = readl(regs + EXYNOS5_DRD_PHYCLKRST);
- phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
- PHYCLKRST_SSC_EN |
- PHYCLKRST_COMMONONN);
- writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
-
- /* Control PHYTEST to remove leakage current */
- phytest = readl(regs + EXYNOS5_DRD_PHYTEST);
- phytest |= (PHYTEST_POWERDOWN_SSP |
- PHYTEST_POWERDOWN_HSP);
- writel(phytest, regs + EXYNOS5_DRD_PHYTEST);
-}
-
-static int samsung_usb3phy_init(struct usb_phy *phy)
-{
- struct samsung_usbphy *sphy;
- unsigned long flags;
- int ret = 0;
-
- sphy = phy_to_sphy(phy);
-
- /* Enable the phy clock */
- ret = clk_prepare_enable(sphy->clk);
- if (ret) {
- dev_err(sphy->dev, "%s: clk_prepare_enable failed\n", __func__);
- return ret;
- }
-
- spin_lock_irqsave(&sphy->lock, flags);
-
- /* setting default phy-type for USB 3.0 */
- samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_DEVICE);
-
- /* Disable phy isolation */
- if (sphy->drv_data->set_isolation)
- sphy->drv_data->set_isolation(sphy, false);
-
- /* Initialize usb phy registers */
- sphy->drv_data->phy_enable(sphy);
-
- spin_unlock_irqrestore(&sphy->lock, flags);
-
- /* Disable the phy clock */
- clk_disable_unprepare(sphy->clk);
-
- return ret;
-}
-
-/*
- * The function passed to the usb driver for phy shutdown
- */
-static void samsung_usb3phy_shutdown(struct usb_phy *phy)
-{
- struct samsung_usbphy *sphy;
- unsigned long flags;
-
- sphy = phy_to_sphy(phy);
-
- if (clk_prepare_enable(sphy->clk)) {
- dev_err(sphy->dev, "%s: clk_prepare_enable failed\n", __func__);
- return;
- }
-
- spin_lock_irqsave(&sphy->lock, flags);
-
- /* setting default phy-type for USB 3.0 */
- samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_DEVICE);
-
- /* De-initialize usb phy registers */
- sphy->drv_data->phy_disable(sphy);
-
- /* Enable phy isolation */
- if (sphy->drv_data->set_isolation)
- sphy->drv_data->set_isolation(sphy, true);
-
- spin_unlock_irqrestore(&sphy->lock, flags);
-
- clk_disable_unprepare(sphy->clk);
-}
-
-static int samsung_usb3phy_probe(struct platform_device *pdev)
-{
- struct samsung_usbphy *sphy;
- struct samsung_usbphy_data *pdata = dev_get_platdata(&pdev->dev);
- struct device *dev = &pdev->dev;
- struct resource *phy_mem;
- void __iomem *phy_base;
- struct clk *clk;
- int ret;
-
- phy_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- phy_base = devm_ioremap_resource(dev, phy_mem);
- if (IS_ERR(phy_base))
- return PTR_ERR(phy_base);
-
- sphy = devm_kzalloc(dev, sizeof(*sphy), GFP_KERNEL);
- if (!sphy)
- return -ENOMEM;
-
- clk = devm_clk_get(dev, "usbdrd30");
- if (IS_ERR(clk)) {
- dev_err(dev, "Failed to get device clock\n");
- return PTR_ERR(clk);
- }
-
- sphy->dev = dev;
-
- if (dev->of_node) {
- ret = samsung_usbphy_parse_dt(sphy);
- if (ret < 0)
- return ret;
- } else {
- if (!pdata) {
- dev_err(dev, "no platform data specified\n");
- return -EINVAL;
- }
- }
-
- sphy->plat = pdata;
- sphy->regs = phy_base;
- sphy->clk = clk;
- sphy->phy.dev = sphy->dev;
- sphy->phy.label = "samsung-usb3phy";
- sphy->phy.type = USB_PHY_TYPE_USB3;
- sphy->phy.init = samsung_usb3phy_init;
- sphy->phy.shutdown = samsung_usb3phy_shutdown;
- sphy->drv_data = samsung_usbphy_get_driver_data(pdev);
-
- sphy->ref_clk_freq = samsung_usbphy_get_refclk_freq(sphy);
- if (sphy->ref_clk_freq < 0)
- return -EINVAL;
-
- spin_lock_init(&sphy->lock);
-
- platform_set_drvdata(pdev, sphy);
-
- return usb_add_phy_dev(&sphy->phy);
-}
-
-static int samsung_usb3phy_remove(struct platform_device *pdev)
-{
- struct samsung_usbphy *sphy = platform_get_drvdata(pdev);
-
- usb_remove_phy(&sphy->phy);
-
- if (sphy->pmuregs)
- iounmap(sphy->pmuregs);
- if (sphy->sysreg)
- iounmap(sphy->sysreg);
-
- return 0;
-}
-
-static struct samsung_usbphy_drvdata usb3phy_exynos5 = {
- .cpu_type = TYPE_EXYNOS5250,
- .devphy_en_mask = EXYNOS_USBPHY_ENABLE,
- .rate_to_clksel = samsung_usbphy_rate_to_clksel_4x12,
- .set_isolation = samsung_usbphy_set_isolation_4210,
- .phy_enable = samsung_exynos5_usb3phy_enable,
- .phy_disable = samsung_exynos5_usb3phy_disable,
-};
-
-#ifdef CONFIG_OF
-static const struct of_device_id samsung_usbphy_dt_match[] = {
- {
- .compatible = "samsung,exynos5250-usb3phy",
- .data = &usb3phy_exynos5
- },
- {},
-};
-MODULE_DEVICE_TABLE(of, samsung_usbphy_dt_match);
-#endif
-
-static struct platform_device_id samsung_usbphy_driver_ids[] = {
- {
- .name = "exynos5250-usb3phy",
- .driver_data = (unsigned long)&usb3phy_exynos5,
- },
- {},
-};
-
-MODULE_DEVICE_TABLE(platform, samsung_usbphy_driver_ids);
-
-static struct platform_driver samsung_usb3phy_driver = {
- .probe = samsung_usb3phy_probe,
- .remove = samsung_usb3phy_remove,
- .id_table = samsung_usbphy_driver_ids,
- .driver = {
- .name = "samsung-usb3phy",
- .owner = THIS_MODULE,
- .of_match_table = of_match_ptr(samsung_usbphy_dt_match),
- },
-};
-
-module_platform_driver(samsung_usb3phy_driver);
-
-MODULE_DESCRIPTION("Samsung USB 3.0 phy controller");
-MODULE_AUTHOR("Vivek Gautam <gautam.vivek@samsung.com>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:samsung-usb3phy");
--
1.7.10.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH RFC 2/7] usb-phy: samsung-usb2: Remove support for Exynos5250
2014-08-14 14:23 [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Vivek Gautam
2014-08-14 14:23 ` [PATCH 1/7] usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver Vivek Gautam
@ 2014-08-14 14:23 ` Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 3/7] usb-phy: samsung-usb2: Remove support for Exynos4X12 Vivek Gautam
` (5 subsequent siblings)
7 siblings, 0 replies; 15+ messages in thread
From: Vivek Gautam @ 2014-08-14 14:23 UTC (permalink / raw)
To: linux-usb, balbi
Cc: linux-kernel, devicetree, grant.likely, gregkh, stern, jg1.han,
s.nawrocki, k.debski, Vivek Gautam
Now that we have moved to new PHY driver for Exynos5250's USB 2.0
controller, which is based on generic phy framework; we no longer
need to keep support of the same in older usb-phy based driver.
So removing this entire code for Exyno5250.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
---
drivers/usb/phy/phy-samsung-usb.c | 9 +-
drivers/usb/phy/phy-samsung-usb.h | 92 -------------------
drivers/usb/phy/phy-samsung-usb2.c | 171 +-----------------------------------
3 files changed, 2 insertions(+), 270 deletions(-)
diff --git a/drivers/usb/phy/phy-samsung-usb.c b/drivers/usb/phy/phy-samsung-usb.c
index ac025ca..a07671d 100644
--- a/drivers/usb/phy/phy-samsung-usb.c
+++ b/drivers/usb/phy/phy-samsung-usb.c
@@ -218,14 +218,7 @@ int samsung_usbphy_get_refclk_freq(struct samsung_usbphy *sphy)
unsigned long rate;
int refclk_freq;
- /*
- * In exynos5250 USB host and device PHY use
- * external crystal clock XXTI
- */
- if (sphy->drv_data->cpu_type == TYPE_EXYNOS5250)
- ref_clk = clk_get(sphy->dev, "ext_xtal");
- else
- ref_clk = clk_get(sphy->dev, "xusbxti");
+ ref_clk = clk_get(sphy->dev, "xusbxti");
if (IS_ERR(ref_clk)) {
dev_err(sphy->dev, "Failed to get reference clock\n");
return PTR_ERR(ref_clk);
diff --git a/drivers/usb/phy/phy-samsung-usb.h b/drivers/usb/phy/phy-samsung-usb.h
index dd2a0b5..7083cb6 100644
--- a/drivers/usb/phy/phy-samsung-usb.h
+++ b/drivers/usb/phy/phy-samsung-usb.h
@@ -57,19 +57,6 @@
#define RSTCON_HOSTPHY_SWRST (0xf << 3)
-/* EXYNOS5 */
-#define EXYNOS5_PHY_HOST_CTRL0 (0x00)
-
-#define HOST_CTRL0_PHYSWRSTALL (0x1 << 31)
-
-#define HOST_CTRL0_REFCLKSEL_MASK (0x3 << 19)
-#define HOST_CTRL0_REFCLKSEL_XTAL (0x0 << 19)
-#define HOST_CTRL0_REFCLKSEL_EXTL (0x1 << 19)
-#define HOST_CTRL0_REFCLKSEL_CLKCORE (0x2 << 19)
-
-#define HOST_CTRL0_FSEL_MASK (0x7 << 16)
-#define HOST_CTRL0_FSEL(_x) ((_x) << 16)
-
#define FSEL_CLKSEL_50M (0x7)
#define FSEL_CLKSEL_24M (0x5)
#define FSEL_CLKSEL_20M (0x4)
@@ -78,83 +65,6 @@
#define FSEL_CLKSEL_10M (0x1)
#define FSEL_CLKSEL_9600K (0x0)
-#define HOST_CTRL0_TESTBURNIN (0x1 << 11)
-#define HOST_CTRL0_RETENABLE (0x1 << 10)
-#define HOST_CTRL0_COMMONON_N (0x1 << 9)
-#define HOST_CTRL0_SIDDQ (0x1 << 6)
-#define HOST_CTRL0_FORCESLEEP (0x1 << 5)
-#define HOST_CTRL0_FORCESUSPEND (0x1 << 4)
-#define HOST_CTRL0_WORDINTERFACE (0x1 << 3)
-#define HOST_CTRL0_UTMISWRST (0x1 << 2)
-#define HOST_CTRL0_LINKSWRST (0x1 << 1)
-#define HOST_CTRL0_PHYSWRST (0x1 << 0)
-
-#define EXYNOS5_PHY_HOST_TUNE0 (0x04)
-
-#define EXYNOS5_PHY_HSIC_CTRL1 (0x10)
-
-#define EXYNOS5_PHY_HSIC_TUNE1 (0x14)
-
-#define EXYNOS5_PHY_HSIC_CTRL2 (0x20)
-
-#define EXYNOS5_PHY_HSIC_TUNE2 (0x24)
-
-#define HSIC_CTRL_REFCLKSEL_MASK (0x3 << 23)
-#define HSIC_CTRL_REFCLKSEL (0x2 << 23)
-
-#define HSIC_CTRL_REFCLKDIV_MASK (0x7f << 16)
-#define HSIC_CTRL_REFCLKDIV(_x) ((_x) << 16)
-#define HSIC_CTRL_REFCLKDIV_12 (0x24 << 16)
-#define HSIC_CTRL_REFCLKDIV_15 (0x1c << 16)
-#define HSIC_CTRL_REFCLKDIV_16 (0x1a << 16)
-#define HSIC_CTRL_REFCLKDIV_19_2 (0x15 << 16)
-#define HSIC_CTRL_REFCLKDIV_20 (0x14 << 16)
-
-#define HSIC_CTRL_SIDDQ (0x1 << 6)
-#define HSIC_CTRL_FORCESLEEP (0x1 << 5)
-#define HSIC_CTRL_FORCESUSPEND (0x1 << 4)
-#define HSIC_CTRL_WORDINTERFACE (0x1 << 3)
-#define HSIC_CTRL_UTMISWRST (0x1 << 2)
-#define HSIC_CTRL_PHYSWRST (0x1 << 0)
-
-#define EXYNOS5_PHY_HOST_EHCICTRL (0x30)
-
-#define HOST_EHCICTRL_ENAINCRXALIGN (0x1 << 29)
-#define HOST_EHCICTRL_ENAINCR4 (0x1 << 28)
-#define HOST_EHCICTRL_ENAINCR8 (0x1 << 27)
-#define HOST_EHCICTRL_ENAINCR16 (0x1 << 26)
-
-#define EXYNOS5_PHY_HOST_OHCICTRL (0x34)
-
-#define HOST_OHCICTRL_SUSPLGCY (0x1 << 3)
-#define HOST_OHCICTRL_APPSTARTCLK (0x1 << 2)
-#define HOST_OHCICTRL_CNTSEL (0x1 << 1)
-#define HOST_OHCICTRL_CLKCKTRST (0x1 << 0)
-
-#define EXYNOS5_PHY_OTG_SYS (0x38)
-
-#define OTG_SYS_PHYLINK_SWRESET (0x1 << 14)
-#define OTG_SYS_LINKSWRST_UOTG (0x1 << 13)
-#define OTG_SYS_PHY0_SWRST (0x1 << 12)
-
-#define OTG_SYS_REFCLKSEL_MASK (0x3 << 9)
-#define OTG_SYS_REFCLKSEL_XTAL (0x0 << 9)
-#define OTG_SYS_REFCLKSEL_EXTL (0x1 << 9)
-#define OTG_SYS_REFCLKSEL_CLKCORE (0x2 << 9)
-
-#define OTG_SYS_IDPULLUP_UOTG (0x1 << 8)
-#define OTG_SYS_COMMON_ON (0x1 << 7)
-
-#define OTG_SYS_FSEL_MASK (0x7 << 4)
-#define OTG_SYS_FSEL(_x) ((_x) << 4)
-
-#define OTG_SYS_FORCESLEEP (0x1 << 3)
-#define OTG_SYS_OTGDISABLE (0x1 << 2)
-#define OTG_SYS_SIDDQ_UOTG (0x1 << 1)
-#define OTG_SYS_FORCESUSPEND (0x1 << 0)
-
-#define EXYNOS5_PHY_OTG_TUNE (0x40)
-
#ifndef MHZ
#define MHZ (1000*1000)
#endif
@@ -163,7 +73,6 @@
#define KHZ (1000)
#endif
-#define EXYNOS_USBHOST_PHY_CTRL_OFFSET (0x4)
#define S3C64XX_USBPHY_ENABLE (0x1 << 16)
#define EXYNOS_USBPHY_ENABLE (0x1 << 0)
#define EXYNOS_USB20PHY_CFG_HOST_LINK (0x1 << 0)
@@ -172,7 +81,6 @@ enum samsung_cpu_type {
TYPE_S3C64XX,
TYPE_EXYNOS4210,
TYPE_EXYNOS4X12,
- TYPE_EXYNOS5250,
};
struct samsung_usbphy;
diff --git a/drivers/usb/phy/phy-samsung-usb2.c b/drivers/usb/phy/phy-samsung-usb2.c
index b3ba866..9bfa436 100644
--- a/drivers/usb/phy/phy-samsung-usb2.c
+++ b/drivers/usb/phy/phy-samsung-usb2.c
@@ -43,121 +43,6 @@ static int samsung_usbphy_set_host(struct usb_otg *otg, struct usb_bus *host)
return 0;
}
-static bool exynos5_phyhost_is_on(void __iomem *regs)
-{
- u32 reg;
-
- reg = readl(regs + EXYNOS5_PHY_HOST_CTRL0);
-
- return !(reg & HOST_CTRL0_SIDDQ);
-}
-
-static void samsung_exynos5_usb2phy_enable(struct samsung_usbphy *sphy)
-{
- void __iomem *regs = sphy->regs;
- u32 phyclk = sphy->ref_clk_freq;
- u32 phyhost;
- u32 phyotg;
- u32 phyhsic;
- u32 ehcictrl;
- u32 ohcictrl;
-
- /*
- * phy_usage helps in keeping usage count for phy
- * so that the first consumer enabling the phy is also
- * the last consumer to disable it.
- */
-
- atomic_inc(&sphy->phy_usage);
-
- if (exynos5_phyhost_is_on(regs)) {
- dev_info(sphy->dev, "Already power on PHY\n");
- return;
- }
-
- /* Host configuration */
- phyhost = readl(regs + EXYNOS5_PHY_HOST_CTRL0);
-
- /* phy reference clock configuration */
- phyhost &= ~HOST_CTRL0_FSEL_MASK;
- phyhost |= HOST_CTRL0_FSEL(phyclk);
-
- /* host phy reset */
- phyhost &= ~(HOST_CTRL0_PHYSWRST |
- HOST_CTRL0_PHYSWRSTALL |
- HOST_CTRL0_SIDDQ |
- /* Enable normal mode of operation */
- HOST_CTRL0_FORCESUSPEND |
- HOST_CTRL0_FORCESLEEP);
-
- /* Link reset */
- phyhost |= (HOST_CTRL0_LINKSWRST |
- HOST_CTRL0_UTMISWRST |
- /* COMMON Block configuration during suspend */
- HOST_CTRL0_COMMONON_N);
- writel(phyhost, regs + EXYNOS5_PHY_HOST_CTRL0);
- udelay(10);
- phyhost &= ~(HOST_CTRL0_LINKSWRST |
- HOST_CTRL0_UTMISWRST);
- writel(phyhost, regs + EXYNOS5_PHY_HOST_CTRL0);
-
- /* OTG configuration */
- phyotg = readl(regs + EXYNOS5_PHY_OTG_SYS);
-
- /* phy reference clock configuration */
- phyotg &= ~OTG_SYS_FSEL_MASK;
- phyotg |= OTG_SYS_FSEL(phyclk);
-
- /* Enable normal mode of operation */
- phyotg &= ~(OTG_SYS_FORCESUSPEND |
- OTG_SYS_SIDDQ_UOTG |
- OTG_SYS_FORCESLEEP |
- OTG_SYS_REFCLKSEL_MASK |
- /* COMMON Block configuration during suspend */
- OTG_SYS_COMMON_ON);
-
- /* OTG phy & link reset */
- phyotg |= (OTG_SYS_PHY0_SWRST |
- OTG_SYS_LINKSWRST_UOTG |
- OTG_SYS_PHYLINK_SWRESET |
- OTG_SYS_OTGDISABLE |
- /* Set phy refclk */
- OTG_SYS_REFCLKSEL_CLKCORE);
-
- writel(phyotg, regs + EXYNOS5_PHY_OTG_SYS);
- udelay(10);
- phyotg &= ~(OTG_SYS_PHY0_SWRST |
- OTG_SYS_LINKSWRST_UOTG |
- OTG_SYS_PHYLINK_SWRESET);
- writel(phyotg, regs + EXYNOS5_PHY_OTG_SYS);
-
- /* HSIC phy configuration */
- phyhsic = (HSIC_CTRL_REFCLKDIV_12 |
- HSIC_CTRL_REFCLKSEL |
- HSIC_CTRL_PHYSWRST);
- writel(phyhsic, regs + EXYNOS5_PHY_HSIC_CTRL1);
- writel(phyhsic, regs + EXYNOS5_PHY_HSIC_CTRL2);
- udelay(10);
- phyhsic &= ~HSIC_CTRL_PHYSWRST;
- writel(phyhsic, regs + EXYNOS5_PHY_HSIC_CTRL1);
- writel(phyhsic, regs + EXYNOS5_PHY_HSIC_CTRL2);
-
- udelay(80);
-
- /* enable EHCI DMA burst */
- ehcictrl = readl(regs + EXYNOS5_PHY_HOST_EHCICTRL);
- ehcictrl |= (HOST_EHCICTRL_ENAINCRXALIGN |
- HOST_EHCICTRL_ENAINCR4 |
- HOST_EHCICTRL_ENAINCR8 |
- HOST_EHCICTRL_ENAINCR16);
- writel(ehcictrl, regs + EXYNOS5_PHY_HOST_EHCICTRL);
-
- /* set ohci_suspend_on_n */
- ohcictrl = readl(regs + EXYNOS5_PHY_HOST_OHCICTRL);
- ohcictrl |= HOST_OHCICTRL_SUSPLGCY;
- writel(ohcictrl, regs + EXYNOS5_PHY_HOST_OHCICTRL);
-}
-
static void samsung_usb2phy_enable(struct samsung_usbphy *sphy)
{
void __iomem *regs = sphy->regs;
@@ -200,41 +85,6 @@ static void samsung_usb2phy_enable(struct samsung_usbphy *sphy)
writel(rstcon, regs + SAMSUNG_RSTCON);
}
-static void samsung_exynos5_usb2phy_disable(struct samsung_usbphy *sphy)
-{
- void __iomem *regs = sphy->regs;
- u32 phyhost;
- u32 phyotg;
- u32 phyhsic;
-
- if (atomic_dec_return(&sphy->phy_usage) > 0) {
- dev_info(sphy->dev, "still being used\n");
- return;
- }
-
- phyhsic = (HSIC_CTRL_REFCLKDIV_12 |
- HSIC_CTRL_REFCLKSEL |
- HSIC_CTRL_SIDDQ |
- HSIC_CTRL_FORCESLEEP |
- HSIC_CTRL_FORCESUSPEND);
- writel(phyhsic, regs + EXYNOS5_PHY_HSIC_CTRL1);
- writel(phyhsic, regs + EXYNOS5_PHY_HSIC_CTRL2);
-
- phyhost = readl(regs + EXYNOS5_PHY_HOST_CTRL0);
- phyhost |= (HOST_CTRL0_SIDDQ |
- HOST_CTRL0_FORCESUSPEND |
- HOST_CTRL0_FORCESLEEP |
- HOST_CTRL0_PHYSWRST |
- HOST_CTRL0_PHYSWRSTALL);
- writel(phyhost, regs + EXYNOS5_PHY_HOST_CTRL0);
-
- phyotg = readl(regs + EXYNOS5_PHY_OTG_SYS);
- phyotg |= (OTG_SYS_FORCESUSPEND |
- OTG_SYS_SIDDQ_UOTG |
- OTG_SYS_FORCESLEEP);
- writel(phyotg, regs + EXYNOS5_PHY_OTG_SYS);
-}
-
static void samsung_usb2phy_disable(struct samsung_usbphy *sphy)
{
void __iomem *regs = sphy->regs;
@@ -382,10 +232,7 @@ static int samsung_usb2phy_probe(struct platform_device *pdev)
drv_data = samsung_usbphy_get_driver_data(pdev);
- if (drv_data->cpu_type == TYPE_EXYNOS5250)
- clk = devm_clk_get(dev, "usbhost");
- else
- clk = devm_clk_get(dev, "otg");
+ clk = devm_clk_get(dev, "otg");
if (IS_ERR(clk)) {
dev_err(dev, "Failed to get usbhost/otg clock\n");
@@ -473,16 +320,6 @@ static const struct samsung_usbphy_drvdata usb2phy_exynos4x12 = {
.phy_disable = samsung_usb2phy_disable,
};
-static struct samsung_usbphy_drvdata usb2phy_exynos5 = {
- .cpu_type = TYPE_EXYNOS5250,
- .hostphy_en_mask = EXYNOS_USBPHY_ENABLE,
- .hostphy_reg_offset = EXYNOS_USBHOST_PHY_CTRL_OFFSET,
- .rate_to_clksel = samsung_usbphy_rate_to_clksel_4x12,
- .set_isolation = samsung_usbphy_set_isolation_4210,
- .phy_enable = samsung_exynos5_usb2phy_enable,
- .phy_disable = samsung_exynos5_usb2phy_disable,
-};
-
#ifdef CONFIG_OF
static const struct of_device_id samsung_usbphy_dt_match[] = {
{
@@ -494,9 +331,6 @@ static const struct of_device_id samsung_usbphy_dt_match[] = {
}, {
.compatible = "samsung,exynos4x12-usb2phy",
.data = &usb2phy_exynos4x12,
- }, {
- .compatible = "samsung,exynos5250-usb2phy",
- .data = &usb2phy_exynos5
},
{},
};
@@ -513,9 +347,6 @@ static struct platform_device_id samsung_usbphy_driver_ids[] = {
}, {
.name = "exynos4x12-usb2phy",
.driver_data = (unsigned long)&usb2phy_exynos4x12,
- }, {
- .name = "exynos5250-usb2phy",
- .driver_data = (unsigned long)&usb2phy_exynos5,
},
{},
};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH RFC 3/7] usb-phy: samsung-usb2: Remove support for Exynos4X12
2014-08-14 14:23 [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Vivek Gautam
2014-08-14 14:23 ` [PATCH 1/7] usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 2/7] usb-phy: samsung-usb2: Remove support for Exynos5250 Vivek Gautam
@ 2014-08-14 14:23 ` Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 4/7] usb-phy: samsung-usb2: Remove support for Exynos4210 Vivek Gautam
` (4 subsequent siblings)
7 siblings, 0 replies; 15+ messages in thread
From: Vivek Gautam @ 2014-08-14 14:23 UTC (permalink / raw)
To: linux-usb, balbi
Cc: linux-kernel, devicetree, grant.likely, gregkh, stern, jg1.han,
s.nawrocki, k.debski, Vivek Gautam
Now that we have moved to new PHY driver for Exynos4X12's USB 2.0
controller, which is based on generic phy framework; so removing
this entire code for Exyno4X12.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
---
drivers/usb/phy/phy-samsung-usb.c | 42 ------------------------------------
drivers/usb/phy/phy-samsung-usb.h | 25 ---------------------
drivers/usb/phy/phy-samsung-usb2.c | 27 -----------------------
3 files changed, 94 deletions(-)
diff --git a/drivers/usb/phy/phy-samsung-usb.c b/drivers/usb/phy/phy-samsung-usb.c
index a07671d..0e40db1 100644
--- a/drivers/usb/phy/phy-samsung-usb.c
+++ b/drivers/usb/phy/phy-samsung-usb.c
@@ -100,11 +100,6 @@ void samsung_usbphy_set_isolation_4210(struct samsung_usbphy *sphy, bool on)
reg_val |= en_mask;
writel(reg_val, reg);
-
- if (sphy->drv_data->cpu_type == TYPE_EXYNOS4X12) {
- writel(reg_val, sphy->pmuregs + EXYNOS4X12_PHY_HSIC_CTRL0);
- writel(reg_val, sphy->pmuregs + EXYNOS4X12_PHY_HSIC_CTRL1);
- }
}
EXPORT_SYMBOL_GPL(samsung_usbphy_set_isolation_4210);
@@ -172,43 +167,6 @@ int samsung_usbphy_rate_to_clksel_64xx(struct samsung_usbphy *sphy,
}
EXPORT_SYMBOL_GPL(samsung_usbphy_rate_to_clksel_64xx);
-int samsung_usbphy_rate_to_clksel_4x12(struct samsung_usbphy *sphy,
- unsigned long rate)
-{
- unsigned int clksel;
-
- switch (rate) {
- case 9600 * KHZ:
- clksel = FSEL_CLKSEL_9600K;
- break;
- case 10 * MHZ:
- clksel = FSEL_CLKSEL_10M;
- break;
- case 12 * MHZ:
- clksel = FSEL_CLKSEL_12M;
- break;
- case 19200 * KHZ:
- clksel = FSEL_CLKSEL_19200K;
- break;
- case 20 * MHZ:
- clksel = FSEL_CLKSEL_20M;
- break;
- case 24 * MHZ:
- clksel = FSEL_CLKSEL_24M;
- break;
- case 50 * MHZ:
- clksel = FSEL_CLKSEL_50M;
- break;
- default:
- dev_err(sphy->dev,
- "Invalid reference clock frequency: %lu\n", rate);
- return -EINVAL;
- }
-
- return clksel;
-}
-EXPORT_SYMBOL_GPL(samsung_usbphy_rate_to_clksel_4x12);
-
/*
* Returns reference clock frequency selection value
*/
diff --git a/drivers/usb/phy/phy-samsung-usb.h b/drivers/usb/phy/phy-samsung-usb.h
index 7083cb6..9d03e3b 100644
--- a/drivers/usb/phy/phy-samsung-usb.h
+++ b/drivers/usb/phy/phy-samsung-usb.h
@@ -47,32 +47,10 @@
#define RSTCON_HLINK_SWRST (0x1 << 1)
#define RSTCON_SWRST (0x1 << 0)
-/* EXYNOS4X12 */
-#define EXYNOS4X12_PHY_HSIC_CTRL0 (0x04)
-#define EXYNOS4X12_PHY_HSIC_CTRL1 (0x08)
-
-#define PHYPWR_NORMAL_MASK_HSIC1 (0x7 << 12)
-#define PHYPWR_NORMAL_MASK_HSIC0 (0x7 << 9)
-#define PHYPWR_NORMAL_MASK_PHY1 (0x7 << 6)
-
-#define RSTCON_HOSTPHY_SWRST (0xf << 3)
-
-#define FSEL_CLKSEL_50M (0x7)
-#define FSEL_CLKSEL_24M (0x5)
-#define FSEL_CLKSEL_20M (0x4)
-#define FSEL_CLKSEL_19200K (0x3)
-#define FSEL_CLKSEL_12M (0x2)
-#define FSEL_CLKSEL_10M (0x1)
-#define FSEL_CLKSEL_9600K (0x0)
-
#ifndef MHZ
#define MHZ (1000*1000)
#endif
-#ifndef KHZ
-#define KHZ (1000)
-#endif
-
#define S3C64XX_USBPHY_ENABLE (0x1 << 16)
#define EXYNOS_USBPHY_ENABLE (0x1 << 0)
#define EXYNOS_USB20PHY_CFG_HOST_LINK (0x1 << 0)
@@ -80,7 +58,6 @@
enum samsung_cpu_type {
TYPE_S3C64XX,
TYPE_EXYNOS4210,
- TYPE_EXYNOS4X12,
};
struct samsung_usbphy;
@@ -173,5 +150,3 @@ extern int samsung_usbphy_set_type(struct usb_phy *phy,
extern int samsung_usbphy_get_refclk_freq(struct samsung_usbphy *sphy);
extern int samsung_usbphy_rate_to_clksel_64xx(struct samsung_usbphy *sphy,
unsigned long rate);
-extern int samsung_usbphy_rate_to_clksel_4x12(struct samsung_usbphy *sphy,
- unsigned long rate);
diff --git a/drivers/usb/phy/phy-samsung-usb2.c b/drivers/usb/phy/phy-samsung-usb2.c
index 9bfa436..6b5ce21 100644
--- a/drivers/usb/phy/phy-samsung-usb2.c
+++ b/drivers/usb/phy/phy-samsung-usb2.c
@@ -61,11 +61,6 @@ static void samsung_usb2phy_enable(struct samsung_usbphy *sphy)
phypwr &= ~PHYPWR_NORMAL_MASK;
rstcon |= RSTCON_SWRST;
break;
- case TYPE_EXYNOS4X12:
- phypwr &= ~(PHYPWR_NORMAL_MASK_HSIC0 |
- PHYPWR_NORMAL_MASK_HSIC1 |
- PHYPWR_NORMAL_MASK_PHY1);
- rstcon |= RSTCON_HOSTPHY_SWRST;
case TYPE_EXYNOS4210:
phypwr &= ~PHYPWR_NORMAL_MASK_PHY0;
rstcon |= RSTCON_SWRST;
@@ -79,8 +74,6 @@ static void samsung_usb2phy_enable(struct samsung_usbphy *sphy)
/* reset all ports of PHY and Link */
writel(rstcon, regs + SAMSUNG_RSTCON);
udelay(10);
- if (sphy->drv_data->cpu_type == TYPE_EXYNOS4X12)
- rstcon &= ~RSTCON_HOSTPHY_SWRST;
rstcon &= ~RSTCON_SWRST;
writel(rstcon, regs + SAMSUNG_RSTCON);
}
@@ -96,10 +89,6 @@ static void samsung_usb2phy_disable(struct samsung_usbphy *sphy)
case TYPE_S3C64XX:
phypwr |= PHYPWR_NORMAL_MASK;
break;
- case TYPE_EXYNOS4X12:
- phypwr |= (PHYPWR_NORMAL_MASK_HSIC0 |
- PHYPWR_NORMAL_MASK_HSIC1 |
- PHYPWR_NORMAL_MASK_PHY1);
case TYPE_EXYNOS4210:
phypwr |= PHYPWR_NORMAL_MASK_PHY0;
default:
@@ -310,16 +299,6 @@ static const struct samsung_usbphy_drvdata usb2phy_exynos4 = {
.phy_disable = samsung_usb2phy_disable,
};
-static const struct samsung_usbphy_drvdata usb2phy_exynos4x12 = {
- .cpu_type = TYPE_EXYNOS4X12,
- .devphy_en_mask = EXYNOS_USBPHY_ENABLE,
- .hostphy_en_mask = EXYNOS_USBPHY_ENABLE,
- .rate_to_clksel = samsung_usbphy_rate_to_clksel_4x12,
- .set_isolation = samsung_usbphy_set_isolation_4210,
- .phy_enable = samsung_usb2phy_enable,
- .phy_disable = samsung_usb2phy_disable,
-};
-
#ifdef CONFIG_OF
static const struct of_device_id samsung_usbphy_dt_match[] = {
{
@@ -328,9 +307,6 @@ static const struct of_device_id samsung_usbphy_dt_match[] = {
}, {
.compatible = "samsung,exynos4210-usb2phy",
.data = &usb2phy_exynos4,
- }, {
- .compatible = "samsung,exynos4x12-usb2phy",
- .data = &usb2phy_exynos4x12,
},
{},
};
@@ -344,9 +320,6 @@ static struct platform_device_id samsung_usbphy_driver_ids[] = {
}, {
.name = "exynos4210-usb2phy",
.driver_data = (unsigned long)&usb2phy_exynos4,
- }, {
- .name = "exynos4x12-usb2phy",
- .driver_data = (unsigned long)&usb2phy_exynos4x12,
},
{},
};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH RFC 4/7] usb-phy: samsung-usb2: Remove support for Exynos4210
2014-08-14 14:23 [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Vivek Gautam
` (2 preceding siblings ...)
2014-08-14 14:23 ` [PATCH RFC 3/7] usb-phy: samsung-usb2: Remove support for Exynos4X12 Vivek Gautam
@ 2014-08-14 14:23 ` Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 5/7] usb-phy: samsung-usb2: Clean up to leave only S3C64XX support Vivek Gautam
` (3 subsequent siblings)
7 siblings, 0 replies; 15+ messages in thread
From: Vivek Gautam @ 2014-08-14 14:23 UTC (permalink / raw)
To: linux-usb, balbi
Cc: linux-kernel, devicetree, grant.likely, gregkh, stern, jg1.han,
s.nawrocki, k.debski, Vivek Gautam
Now that we have moved to new PHY driver for Exynos4210's USB 2.0
controller, which is based on generic phy framework; so removing
the code for Exyno4210.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
---
drivers/usb/phy/phy-samsung-usb.c | 35 -----------------------------------
drivers/usb/phy/phy-samsung-usb.h | 4 ----
drivers/usb/phy/phy-samsung-usb2.c | 23 -----------------------
3 files changed, 62 deletions(-)
diff --git a/drivers/usb/phy/phy-samsung-usb.c b/drivers/usb/phy/phy-samsung-usb.c
index 0e40db1..51c4102 100644
--- a/drivers/usb/phy/phy-samsung-usb.c
+++ b/drivers/usb/phy/phy-samsung-usb.c
@@ -69,41 +69,6 @@ err0:
EXPORT_SYMBOL_GPL(samsung_usbphy_parse_dt);
/*
- * Set isolation here for phy.
- * Here 'on = true' would mean USB PHY block is isolated, hence
- * de-activated and vice-versa.
- */
-void samsung_usbphy_set_isolation_4210(struct samsung_usbphy *sphy, bool on)
-{
- void __iomem *reg = NULL;
- u32 reg_val;
- u32 en_mask = 0;
-
- if (!sphy->pmuregs) {
- dev_warn(sphy->dev, "Can't set pmu isolation\n");
- return;
- }
-
- if (sphy->phy_type == USB_PHY_TYPE_DEVICE) {
- reg = sphy->pmuregs + sphy->drv_data->devphy_reg_offset;
- en_mask = sphy->drv_data->devphy_en_mask;
- } else if (sphy->phy_type == USB_PHY_TYPE_HOST) {
- reg = sphy->pmuregs + sphy->drv_data->hostphy_reg_offset;
- en_mask = sphy->drv_data->hostphy_en_mask;
- }
-
- reg_val = readl(reg);
-
- if (on)
- reg_val &= ~en_mask;
- else
- reg_val |= en_mask;
-
- writel(reg_val, reg);
-}
-EXPORT_SYMBOL_GPL(samsung_usbphy_set_isolation_4210);
-
-/*
* Configure the mode of working of usb-phy here: HOST/DEVICE.
*/
void samsung_usbphy_cfg_sel(struct samsung_usbphy *sphy)
diff --git a/drivers/usb/phy/phy-samsung-usb.h b/drivers/usb/phy/phy-samsung-usb.h
index 9d03e3b..b36fd88 100644
--- a/drivers/usb/phy/phy-samsung-usb.h
+++ b/drivers/usb/phy/phy-samsung-usb.h
@@ -52,12 +52,10 @@
#endif
#define S3C64XX_USBPHY_ENABLE (0x1 << 16)
-#define EXYNOS_USBPHY_ENABLE (0x1 << 0)
#define EXYNOS_USB20PHY_CFG_HOST_LINK (0x1 << 0)
enum samsung_cpu_type {
TYPE_S3C64XX,
- TYPE_EXYNOS4210,
};
struct samsung_usbphy;
@@ -142,8 +140,6 @@ static inline const struct samsung_usbphy_drvdata
}
extern int samsung_usbphy_parse_dt(struct samsung_usbphy *sphy);
-extern void samsung_usbphy_set_isolation_4210(struct samsung_usbphy *sphy,
- bool on);
extern void samsung_usbphy_cfg_sel(struct samsung_usbphy *sphy);
extern int samsung_usbphy_set_type(struct usb_phy *phy,
enum samsung_usb_phy_type phy_type);
diff --git a/drivers/usb/phy/phy-samsung-usb2.c b/drivers/usb/phy/phy-samsung-usb2.c
index 6b5ce21..2bcc948 100644
--- a/drivers/usb/phy/phy-samsung-usb2.c
+++ b/drivers/usb/phy/phy-samsung-usb2.c
@@ -60,10 +60,6 @@ static void samsung_usb2phy_enable(struct samsung_usbphy *sphy)
phyclk &= ~PHYCLK_COMMON_ON_N;
phypwr &= ~PHYPWR_NORMAL_MASK;
rstcon |= RSTCON_SWRST;
- break;
- case TYPE_EXYNOS4210:
- phypwr &= ~PHYPWR_NORMAL_MASK_PHY0;
- rstcon |= RSTCON_SWRST;
default:
break;
}
@@ -88,9 +84,6 @@ static void samsung_usb2phy_disable(struct samsung_usbphy *sphy)
switch (sphy->drv_data->cpu_type) {
case TYPE_S3C64XX:
phypwr |= PHYPWR_NORMAL_MASK;
- break;
- case TYPE_EXYNOS4210:
- phypwr |= PHYPWR_NORMAL_MASK_PHY0;
default:
break;
}
@@ -289,24 +282,11 @@ static const struct samsung_usbphy_drvdata usb2phy_s3c64xx = {
.phy_disable = samsung_usb2phy_disable,
};
-static const struct samsung_usbphy_drvdata usb2phy_exynos4 = {
- .cpu_type = TYPE_EXYNOS4210,
- .devphy_en_mask = EXYNOS_USBPHY_ENABLE,
- .hostphy_en_mask = EXYNOS_USBPHY_ENABLE,
- .rate_to_clksel = samsung_usbphy_rate_to_clksel_64xx,
- .set_isolation = samsung_usbphy_set_isolation_4210,
- .phy_enable = samsung_usb2phy_enable,
- .phy_disable = samsung_usb2phy_disable,
-};
-
#ifdef CONFIG_OF
static const struct of_device_id samsung_usbphy_dt_match[] = {
{
.compatible = "samsung,s3c64xx-usb2phy",
.data = &usb2phy_s3c64xx,
- }, {
- .compatible = "samsung,exynos4210-usb2phy",
- .data = &usb2phy_exynos4,
},
{},
};
@@ -317,9 +297,6 @@ static struct platform_device_id samsung_usbphy_driver_ids[] = {
{
.name = "s3c64xx-usb2phy",
.driver_data = (unsigned long)&usb2phy_s3c64xx,
- }, {
- .name = "exynos4210-usb2phy",
- .driver_data = (unsigned long)&usb2phy_exynos4,
},
{},
};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH RFC 5/7] usb-phy: samsung-usb2: Clean up to leave only S3C64XX support
2014-08-14 14:23 [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Vivek Gautam
` (3 preceding siblings ...)
2014-08-14 14:23 ` [PATCH RFC 4/7] usb-phy: samsung-usb2: Remove support for Exynos4210 Vivek Gautam
@ 2014-08-14 14:23 ` Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 6/7] usb: host: ehci-exynos: Remove unnecessary usb-phy support Vivek Gautam
` (2 subsequent siblings)
7 siblings, 0 replies; 15+ messages in thread
From: Vivek Gautam @ 2014-08-14 14:23 UTC (permalink / raw)
To: linux-usb, balbi
Cc: linux-kernel, devicetree, grant.likely, gregkh, stern, jg1.han,
s.nawrocki, k.debski, Vivek Gautam
Cleaning up the driver further to enable only S3C64XX phy support,
while the support for rest all SoCs is removed in previous patches.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
---
- In the changes that have been left for S3C64XX, we have added DT based
pmu-isolation support for S3C64XX boards too, wherein they get system-controller
register offset and update the PHY control bit using regmap.
drivers/usb/phy/Kconfig | 8 --
drivers/usb/phy/Makefile | 1 -
drivers/usb/phy/phy-samsung-usb.c | 157 ---------------------------------
drivers/usb/phy/phy-samsung-usb.h | 148 -------------------------------
drivers/usb/phy/phy-samsung-usb2.c | 170 ++++++++++++++++++------------------
drivers/usb/phy/phy-samsung-usb2.h | 121 +++++++++++++++++++++++++
6 files changed, 205 insertions(+), 400 deletions(-)
delete mode 100644 drivers/usb/phy/phy-samsung-usb.c
delete mode 100644 drivers/usb/phy/phy-samsung-usb.h
create mode 100644 drivers/usb/phy/phy-samsung-usb2.h
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 751b594..415d0fb 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -71,16 +71,8 @@ config AM335X_PHY_USB
This driver provides PHY support for that phy which part for the
AM335x SoC.
-config SAMSUNG_USBPHY
- tristate
- help
- Enable this to support Samsung USB phy helper driver for Samsung SoCs.
- This driver provides common interface to interact, for Samsung USB 2.0 PHY
- driver and later for Samsung USB 3.0 PHY driver.
-
config SAMSUNG_USB2PHY
tristate "Samsung USB 2.0 PHY controller Driver"
- select SAMSUNG_USBPHY
select USB_PHY
help
Enable this to support Samsung USB 2.0 (High Speed) PHY controller
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index 9c984dd..0b9c734 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -14,7 +14,6 @@ obj-$(CONFIG_TAHVO_USB) += phy-tahvo.o
obj-$(CONFIG_AM335X_CONTROL_USB) += phy-am335x-control.o
obj-$(CONFIG_AM335X_PHY_USB) += phy-am335x.o
obj-$(CONFIG_OMAP_OTG) += phy-omap-otg.o
-obj-$(CONFIG_SAMSUNG_USBPHY) += phy-samsung-usb.o
obj-$(CONFIG_SAMSUNG_USB2PHY) += phy-samsung-usb2.o
obj-$(CONFIG_TWL6030_USB) += phy-twl6030-usb.o
obj-$(CONFIG_USB_EHCI_TEGRA) += phy-tegra-usb.o
diff --git a/drivers/usb/phy/phy-samsung-usb.c b/drivers/usb/phy/phy-samsung-usb.c
deleted file mode 100644
index 51c4102..0000000
--- a/drivers/usb/phy/phy-samsung-usb.c
+++ /dev/null
@@ -1,157 +0,0 @@
-/* linux/drivers/usb/phy/phy-samsung-usb.c
- *
- * Copyright (c) 2012 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * Author: Praveen Paneri <p.paneri@samsung.com>
- *
- * Samsung USB-PHY helper driver with common function calls;
- * interacts with Samsung USB 2.0 PHY controller driver and later
- * with Samsung USB 3.0 PHY driver.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/device.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/usb/samsung_usb_phy.h>
-
-#include "phy-samsung-usb.h"
-
-int samsung_usbphy_parse_dt(struct samsung_usbphy *sphy)
-{
- struct device_node *usbphy_sys;
-
- /* Getting node for system controller interface for usb-phy */
- usbphy_sys = of_get_child_by_name(sphy->dev->of_node, "usbphy-sys");
- if (!usbphy_sys) {
- dev_err(sphy->dev, "No sys-controller interface for usb-phy\n");
- return -ENODEV;
- }
-
- sphy->pmuregs = of_iomap(usbphy_sys, 0);
-
- if (sphy->pmuregs == NULL) {
- dev_err(sphy->dev, "Can't get usb-phy pmu control register\n");
- goto err0;
- }
-
- sphy->sysreg = of_iomap(usbphy_sys, 1);
-
- /*
- * Not returning error code here, since this situation is not fatal.
- * Few SoCs may not have this switch available
- */
- if (sphy->sysreg == NULL)
- dev_warn(sphy->dev, "Can't get usb-phy sysreg cfg register\n");
-
- of_node_put(usbphy_sys);
-
- return 0;
-
-err0:
- of_node_put(usbphy_sys);
- return -ENXIO;
-}
-EXPORT_SYMBOL_GPL(samsung_usbphy_parse_dt);
-
-/*
- * Configure the mode of working of usb-phy here: HOST/DEVICE.
- */
-void samsung_usbphy_cfg_sel(struct samsung_usbphy *sphy)
-{
- u32 reg;
-
- if (!sphy->sysreg) {
- dev_warn(sphy->dev, "Can't configure specified phy mode\n");
- return;
- }
-
- reg = readl(sphy->sysreg);
-
- if (sphy->phy_type == USB_PHY_TYPE_DEVICE)
- reg &= ~EXYNOS_USB20PHY_CFG_HOST_LINK;
- else if (sphy->phy_type == USB_PHY_TYPE_HOST)
- reg |= EXYNOS_USB20PHY_CFG_HOST_LINK;
-
- writel(reg, sphy->sysreg);
-}
-EXPORT_SYMBOL_GPL(samsung_usbphy_cfg_sel);
-
-/*
- * PHYs are different for USB Device and USB Host.
- * This make sure that correct PHY type is selected before
- * any operation on PHY.
- */
-int samsung_usbphy_set_type(struct usb_phy *phy,
- enum samsung_usb_phy_type phy_type)
-{
- struct samsung_usbphy *sphy = phy_to_sphy(phy);
-
- sphy->phy_type = phy_type;
-
- return 0;
-}
-EXPORT_SYMBOL_GPL(samsung_usbphy_set_type);
-
-int samsung_usbphy_rate_to_clksel_64xx(struct samsung_usbphy *sphy,
- unsigned long rate)
-{
- unsigned int clksel;
-
- switch (rate) {
- case 12 * MHZ:
- clksel = PHYCLK_CLKSEL_12M;
- break;
- case 24 * MHZ:
- clksel = PHYCLK_CLKSEL_24M;
- break;
- case 48 * MHZ:
- clksel = PHYCLK_CLKSEL_48M;
- break;
- default:
- dev_err(sphy->dev,
- "Invalid reference clock frequency: %lu\n", rate);
- return -EINVAL;
- }
-
- return clksel;
-}
-EXPORT_SYMBOL_GPL(samsung_usbphy_rate_to_clksel_64xx);
-
-/*
- * Returns reference clock frequency selection value
- */
-int samsung_usbphy_get_refclk_freq(struct samsung_usbphy *sphy)
-{
- struct clk *ref_clk;
- unsigned long rate;
- int refclk_freq;
-
- ref_clk = clk_get(sphy->dev, "xusbxti");
- if (IS_ERR(ref_clk)) {
- dev_err(sphy->dev, "Failed to get reference clock\n");
- return PTR_ERR(ref_clk);
- }
-
- rate = clk_get_rate(ref_clk);
- refclk_freq = sphy->drv_data->rate_to_clksel(sphy, rate);
-
- clk_put(ref_clk);
-
- return refclk_freq;
-}
-EXPORT_SYMBOL_GPL(samsung_usbphy_get_refclk_freq);
diff --git a/drivers/usb/phy/phy-samsung-usb.h b/drivers/usb/phy/phy-samsung-usb.h
deleted file mode 100644
index b36fd88..0000000
--- a/drivers/usb/phy/phy-samsung-usb.h
+++ /dev/null
@@ -1,148 +0,0 @@
-/* linux/drivers/usb/phy/phy-samsung-usb.h
- *
- * Copyright (c) 2012 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * Samsung USB-PHY transceiver; talks to S3C HS OTG controller, EHCI-S5P and
- * OHCI-EXYNOS controllers.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/usb/phy.h>
-
-/* Register definitions */
-
-#define SAMSUNG_PHYPWR (0x00)
-
-#define PHYPWR_NORMAL_MASK (0x19 << 0)
-#define PHYPWR_OTG_DISABLE (0x1 << 4)
-#define PHYPWR_ANALOG_POWERDOWN (0x1 << 3)
-#define PHYPWR_FORCE_SUSPEND (0x1 << 1)
-/* For Exynos4 */
-#define PHYPWR_NORMAL_MASK_PHY0 (0x39 << 0)
-#define PHYPWR_SLEEP_PHY0 (0x1 << 5)
-
-#define SAMSUNG_PHYCLK (0x04)
-
-#define PHYCLK_MODE_USB11 (0x1 << 6)
-#define PHYCLK_EXT_OSC (0x1 << 5)
-#define PHYCLK_COMMON_ON_N (0x1 << 4)
-#define PHYCLK_ID_PULL (0x1 << 2)
-#define PHYCLK_CLKSEL_MASK (0x3 << 0)
-#define PHYCLK_CLKSEL_48M (0x0 << 0)
-#define PHYCLK_CLKSEL_12M (0x2 << 0)
-#define PHYCLK_CLKSEL_24M (0x3 << 0)
-
-#define SAMSUNG_RSTCON (0x08)
-
-#define RSTCON_PHYLINK_SWRST (0x1 << 2)
-#define RSTCON_HLINK_SWRST (0x1 << 1)
-#define RSTCON_SWRST (0x1 << 0)
-
-#ifndef MHZ
-#define MHZ (1000*1000)
-#endif
-
-#define S3C64XX_USBPHY_ENABLE (0x1 << 16)
-#define EXYNOS_USB20PHY_CFG_HOST_LINK (0x1 << 0)
-
-enum samsung_cpu_type {
- TYPE_S3C64XX,
-};
-
-struct samsung_usbphy;
-
-/*
- * struct samsung_usbphy_drvdata - driver data for various SoC variants
- * @cpu_type: machine identifier
- * @devphy_en_mask: device phy enable mask for PHY CONTROL register
- * @hostphy_en_mask: host phy enable mask for PHY CONTROL register
- * @devphy_reg_offset: offset to DEVICE PHY CONTROL register from
- * mapped address of system controller.
- * @hostphy_reg_offset: offset to HOST PHY CONTROL register from
- * mapped address of system controller.
- *
- * Here we have a separate mask for device type phy.
- * Having different masks for host and device type phy helps
- * in setting independent masks in case of SoCs like S5PV210,
- * in which PHY0 and PHY1 enable bits belong to same register
- * placed at position 0 and 1 respectively.
- * Although for newer SoCs like exynos these bits belong to
- * different registers altogether placed at position 0.
- */
-struct samsung_usbphy_drvdata {
- int cpu_type;
- int devphy_en_mask;
- int hostphy_en_mask;
- u32 devphy_reg_offset;
- u32 hostphy_reg_offset;
- int (*rate_to_clksel)(struct samsung_usbphy *, unsigned long);
- void (*set_isolation)(struct samsung_usbphy *, bool);
- void (*phy_enable)(struct samsung_usbphy *);
- void (*phy_disable)(struct samsung_usbphy *);
-};
-
-/*
- * struct samsung_usbphy - transceiver driver state
- * @phy: transceiver structure
- * @plat: platform data
- * @dev: The parent device supplied to the probe function
- * @clk: usb phy clock
- * @regs: usb phy controller registers memory base
- * @pmuregs: USB device PHY_CONTROL register memory base
- * @sysreg: USB2.0 PHY_CFG register memory base
- * @ref_clk_freq: reference clock frequency selection
- * @drv_data: driver data available for different SoCs
- * @phy_type: Samsung SoCs specific phy types: #HOST
- * #DEVICE
- * @phy_usage: usage count for phy
- * @lock: lock for phy operations
- */
-struct samsung_usbphy {
- struct usb_phy phy;
- struct samsung_usbphy_data *plat;
- struct device *dev;
- struct clk *clk;
- void __iomem *regs;
- void __iomem *pmuregs;
- void __iomem *sysreg;
- int ref_clk_freq;
- const struct samsung_usbphy_drvdata *drv_data;
- enum samsung_usb_phy_type phy_type;
- atomic_t phy_usage;
- spinlock_t lock;
-};
-
-#define phy_to_sphy(x) container_of((x), struct samsung_usbphy, phy)
-
-static const struct of_device_id samsung_usbphy_dt_match[];
-
-static inline const struct samsung_usbphy_drvdata
-*samsung_usbphy_get_driver_data(struct platform_device *pdev)
-{
- if (pdev->dev.of_node) {
- const struct of_device_id *match;
- match = of_match_node(samsung_usbphy_dt_match,
- pdev->dev.of_node);
- return match->data;
- }
-
- return (struct samsung_usbphy_drvdata *)
- platform_get_device_id(pdev)->driver_data;
-}
-
-extern int samsung_usbphy_parse_dt(struct samsung_usbphy *sphy);
-extern void samsung_usbphy_cfg_sel(struct samsung_usbphy *sphy);
-extern int samsung_usbphy_set_type(struct usb_phy *phy,
- enum samsung_usb_phy_type phy_type);
-extern int samsung_usbphy_get_refclk_freq(struct samsung_usbphy *sphy);
-extern int samsung_usbphy_rate_to_clksel_64xx(struct samsung_usbphy *sphy,
- unsigned long rate);
diff --git a/drivers/usb/phy/phy-samsung-usb2.c b/drivers/usb/phy/phy-samsung-usb2.c
index 2bcc948..2395b92 100644
--- a/drivers/usb/phy/phy-samsung-usb2.c
+++ b/drivers/usb/phy/phy-samsung-usb2.c
@@ -25,71 +25,108 @@
#include <linux/device.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/mfd/syscon.h>
#include <linux/of.h>
+#include <linux/of_address.h>
#include <linux/usb/otg.h>
#include <linux/usb/samsung_usb_phy.h>
#include <linux/platform_data/samsung-usbphy.h>
-#include "phy-samsung-usb.h"
+#include "phy-samsung-usb2.h"
-static int samsung_usbphy_set_host(struct usb_otg *otg, struct usb_bus *host)
+static void samsung_usbphy_set_isolation(struct samsung_usbphy *sphy, bool on)
{
- if (!otg)
- return -ENODEV;
+ unsigned int val;
- if (!otg->host)
- otg->host = host;
+ if (!sphy->syscon_reg)
+ return;
- return 0;
+ val = on ? 0 : MISC_CTRL_USB_SIG_MASK;
+
+ regmap_update_bits(sphy->syscon_reg, sphy->drv_data->devphy_reg_offset,
+ MISC_CTRL_USB_SIG_MASK, val);
+}
+
+static int samsung_usbphy_rate_to_clksel_64xx(struct samsung_usbphy *sphy,
+ unsigned long rate)
+{
+ unsigned int clksel;
+
+ switch (rate) {
+ case 12 * MHZ:
+ clksel = PHYCLK_CLKSEL_12M;
+ break;
+ case 24 * MHZ:
+ clksel = PHYCLK_CLKSEL_24M;
+ break;
+ case 48 * MHZ:
+ clksel = PHYCLK_CLKSEL_48M;
+ break;
+ default:
+ dev_err(sphy->dev,
+ "Invalid reference clock frequency: %lu\n", rate);
+ return -EINVAL;
+ }
+
+ return clksel;
+}
+
+/*
+ * Returns reference clock frequency selection value
+ */
+static int samsung_usbphy_get_refclk_freq(struct samsung_usbphy *sphy)
+{
+ struct clk *ref_clk;
+ unsigned long rate;
+ int refclk_freq;
+
+ ref_clk = clk_get(sphy->dev, "xusbxti");
+ if (IS_ERR(ref_clk)) {
+ dev_err(sphy->dev, "Failed to get reference clock\n");
+ return PTR_ERR(ref_clk);
+ }
+
+ rate = clk_get_rate(ref_clk);
+ refclk_freq = sphy->drv_data->rate_to_clksel(sphy, rate);
+
+ clk_put(ref_clk);
+
+ return refclk_freq;
}
static void samsung_usb2phy_enable(struct samsung_usbphy *sphy)
{
void __iomem *regs = sphy->regs;
- u32 phypwr;
- u32 phyclk;
- u32 rstcon;
+ u32 reg_val;
+ reg_val = sphy->ref_clk_freq;
/* set clock frequency for PLL */
- phyclk = sphy->ref_clk_freq;
- phypwr = readl(regs + SAMSUNG_PHYPWR);
- rstcon = readl(regs + SAMSUNG_RSTCON);
-
- switch (sphy->drv_data->cpu_type) {
- case TYPE_S3C64XX:
- phyclk &= ~PHYCLK_COMMON_ON_N;
- phypwr &= ~PHYPWR_NORMAL_MASK;
- rstcon |= RSTCON_SWRST;
- default:
- break;
- }
+ reg_val &= ~PHYCLK_COMMON_ON_N;
+ writel(reg_val, regs + SAMSUNG_PHYCLK);
- writel(phyclk, regs + SAMSUNG_PHYCLK);
+ reg_val = readl(regs + SAMSUNG_PHYPWR);
/* Configure PHY0 for normal operation*/
- writel(phypwr, regs + SAMSUNG_PHYPWR);
+ reg_val &= ~PHYPWR_NORMAL_MASK;
+ writel(reg_val, regs + SAMSUNG_PHYPWR);
+
+ reg_val = readl(regs + SAMSUNG_RSTCON);
/* reset all ports of PHY and Link */
- writel(rstcon, regs + SAMSUNG_RSTCON);
+ reg_val |= RSTCON_SWRST;
+ writel(reg_val, regs + SAMSUNG_RSTCON);
udelay(10);
- rstcon &= ~RSTCON_SWRST;
- writel(rstcon, regs + SAMSUNG_RSTCON);
+ reg_val &= ~RSTCON_SWRST;
+ writel(reg_val, regs + SAMSUNG_RSTCON);
}
static void samsung_usb2phy_disable(struct samsung_usbphy *sphy)
{
void __iomem *regs = sphy->regs;
- u32 phypwr;
-
- phypwr = readl(regs + SAMSUNG_PHYPWR);
-
- switch (sphy->drv_data->cpu_type) {
- case TYPE_S3C64XX:
- phypwr |= PHYPWR_NORMAL_MASK;
- default:
- break;
- }
+ u32 reg_val;
+ reg_val = readl(regs + SAMSUNG_PHYPWR);
/* Disable analog and otg block power */
- writel(phypwr, regs + SAMSUNG_PHYPWR);
+ reg_val |= PHYPWR_NORMAL_MASK;
+ writel(reg_val, regs + SAMSUNG_PHYPWR);
}
/*
@@ -98,14 +135,11 @@ static void samsung_usb2phy_disable(struct samsung_usbphy *sphy)
static int samsung_usb2phy_init(struct usb_phy *phy)
{
struct samsung_usbphy *sphy;
- struct usb_bus *host = NULL;
unsigned long flags;
int ret = 0;
sphy = phy_to_sphy(phy);
- host = phy->otg->host;
-
/* Enable the phy clock */
ret = clk_prepare_enable(sphy->clk);
if (ret) {
@@ -115,24 +149,12 @@ static int samsung_usb2phy_init(struct usb_phy *phy)
spin_lock_irqsave(&sphy->lock, flags);
- if (host) {
- /* setting default phy-type for USB 2.0 */
- if (!strstr(dev_name(host->controller), "ehci") ||
- !strstr(dev_name(host->controller), "ohci"))
- samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_HOST);
- } else {
- samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_DEVICE);
- }
-
/* Disable phy isolation */
if (sphy->plat && sphy->plat->pmu_isolation)
sphy->plat->pmu_isolation(false);
else if (sphy->drv_data->set_isolation)
sphy->drv_data->set_isolation(sphy, false);
- /* Selecting Host/OTG mode; After reset USB2.0PHY_CFG: HOST */
- samsung_usbphy_cfg_sel(sphy);
-
/* Initialize usb phy registers */
sphy->drv_data->phy_enable(sphy);
@@ -150,13 +172,10 @@ static int samsung_usb2phy_init(struct usb_phy *phy)
static void samsung_usb2phy_shutdown(struct usb_phy *phy)
{
struct samsung_usbphy *sphy;
- struct usb_bus *host = NULL;
unsigned long flags;
sphy = phy_to_sphy(phy);
- host = phy->otg->host;
-
if (clk_prepare_enable(sphy->clk)) {
dev_err(sphy->dev, "%s: clk_prepare_enable failed\n", __func__);
return;
@@ -164,15 +183,6 @@ static void samsung_usb2phy_shutdown(struct usb_phy *phy)
spin_lock_irqsave(&sphy->lock, flags);
- if (host) {
- /* setting default phy-type for USB 2.0 */
- if (!strstr(dev_name(host->controller), "ehci") ||
- !strstr(dev_name(host->controller), "ohci"))
- samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_HOST);
- } else {
- samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_DEVICE);
- }
-
/* De-initialize usb phy registers */
sphy->drv_data->phy_disable(sphy);
@@ -190,14 +200,12 @@ static void samsung_usb2phy_shutdown(struct usb_phy *phy)
static int samsung_usb2phy_probe(struct platform_device *pdev)
{
struct samsung_usbphy *sphy;
- struct usb_otg *otg;
struct samsung_usbphy_data *pdata = dev_get_platdata(&pdev->dev);
const struct samsung_usbphy_drvdata *drv_data;
struct device *dev = &pdev->dev;
struct resource *phy_mem;
void __iomem *phy_base;
struct clk *clk;
- int ret;
phy_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
phy_base = devm_ioremap_resource(dev, phy_mem);
@@ -208,25 +216,24 @@ static int samsung_usb2phy_probe(struct platform_device *pdev)
if (!sphy)
return -ENOMEM;
- otg = devm_kzalloc(dev, sizeof(*otg), GFP_KERNEL);
- if (!otg)
- return -ENOMEM;
-
drv_data = samsung_usbphy_get_driver_data(pdev);
clk = devm_clk_get(dev, "otg");
if (IS_ERR(clk)) {
- dev_err(dev, "Failed to get usbhost/otg clock\n");
+ dev_err(dev, "Failed to get otg clock\n");
return PTR_ERR(clk);
}
sphy->dev = dev;
if (dev->of_node) {
- ret = samsung_usbphy_parse_dt(sphy);
- if (ret < 0)
- return ret;
+ sphy->syscon_reg = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "samsung,syscon-phandle");
+ if (IS_ERR(sphy->syscon_reg)) {
+ dev_err(dev, "Failed to lookup Control regmap\n");
+ return PTR_ERR(sphy->syscon_reg);
+ }
} else {
if (!pdata) {
dev_err(dev, "no platform data specified\n");
@@ -248,10 +255,6 @@ static int samsung_usb2phy_probe(struct platform_device *pdev)
if (sphy->ref_clk_freq < 0)
return -EINVAL;
- sphy->phy.otg = otg;
- sphy->phy.otg->phy = &sphy->phy;
- sphy->phy.otg->set_host = samsung_usbphy_set_host;
-
spin_lock_init(&sphy->lock);
platform_set_drvdata(pdev, sphy);
@@ -265,19 +268,14 @@ static int samsung_usb2phy_remove(struct platform_device *pdev)
usb_remove_phy(&sphy->phy);
- if (sphy->pmuregs)
- iounmap(sphy->pmuregs);
- if (sphy->sysreg)
- iounmap(sphy->sysreg);
-
return 0;
}
static const struct samsung_usbphy_drvdata usb2phy_s3c64xx = {
.cpu_type = TYPE_S3C64XX,
- .devphy_en_mask = S3C64XX_USBPHY_ENABLE,
+ .devphy_reg_offset = S3C64XX_MISC_CTRL,
.rate_to_clksel = samsung_usbphy_rate_to_clksel_64xx,
- .set_isolation = NULL, /* TODO */
+ .set_isolation = samsung_usbphy_set_isolation,
.phy_enable = samsung_usb2phy_enable,
.phy_disable = samsung_usb2phy_disable,
};
diff --git a/drivers/usb/phy/phy-samsung-usb2.h b/drivers/usb/phy/phy-samsung-usb2.h
new file mode 100644
index 0000000..5543a99
--- /dev/null
+++ b/drivers/usb/phy/phy-samsung-usb2.h
@@ -0,0 +1,121 @@
+/* linux/drivers/usb/phy/phy-samsung-usb.h
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * Samsung USB-PHY transceiver; talks to S3C HS OTG controller, EHCI-S5P and
+ * OHCI-EXYNOS controllers.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/usb/phy.h>
+#include <linux/regmap.h>
+
+/* Register definitions */
+
+#define SAMSUNG_PHYPWR (0x00)
+#define PHYPWR_NORMAL_MASK (0x19 << 0)
+#define PHYPWR_OTG_DISABLE BIT(4)
+#define PHYPWR_ANALOG_POWERDOWN BIT(3)
+#define PHYPWR_FORCE_SUSPEND BIT(1)
+/* For Exynos4 */
+#define PHYPWR_NORMAL_MASK_PHY0 (0x39 << 0)
+#define PHYPWR_SLEEP_PHY0 BIT(5)
+
+#define SAMSUNG_PHYCLK (0x04)
+#define PHYCLK_MODE_USB11 BIT(6)
+#define PHYCLK_EXT_OSC BIT(5)
+#define PHYCLK_COMMON_ON_N BIT(4)
+#define PHYCLK_ID_PULL BIT(2)
+#define PHYCLK_CLKSEL_MASK (0x3 << 0)
+#define PHYCLK_CLKSEL_48M (0x0 << 0)
+#define PHYCLK_CLKSEL_12M (0x2 << 0)
+#define PHYCLK_CLKSEL_24M (0x3 << 0)
+
+#define SAMSUNG_RSTCON (0x08)
+#define RSTCON_PHYLINK_SWRST BIT(2)
+#define RSTCON_HLINK_SWRST BIT(1)
+#define RSTCON_SWRST BIT(0)
+
+#ifndef MHZ
+#define MHZ (1000*1000)
+#endif
+
+#define S3C64XX_MISC_CTRL (0x800) /* Aka: OTHERS */
+#define MISC_CTRL_USB_SIG_MASK BIT(16)
+
+enum samsung_cpu_type {
+ TYPE_S3C64XX,
+};
+
+struct samsung_usbphy;
+
+/*
+ * struct samsung_usbphy_drvdata - driver data for various SoC variants
+ * @cpu_type: machine identifier
+ * @devphy_reg_offset: offset to DEVICE PHY CONTROL register from
+ * mapped address of system controller.
+ */
+struct samsung_usbphy_drvdata {
+ int cpu_type;
+ u32 devphy_reg_offset;
+ int (*rate_to_clksel)(struct samsung_usbphy *, unsigned long);
+ void (*set_isolation)(struct samsung_usbphy *, bool);
+ void (*phy_enable)(struct samsung_usbphy *);
+ void (*phy_disable)(struct samsung_usbphy *);
+};
+
+/*
+ * struct samsung_usbphy - transceiver driver state
+ * @phy: transceiver structure
+ * @plat: platform data
+ * @dev: The parent device supplied to the probe function
+ * @clk: usb phy clock
+ * @regs: usb phy controller registers memory base
+ * @syscon_reg: register map for controlling 'OTHER SFRs' @ 0xE0100100,
+ * present as a part of clock controller, but instead
+ * they serve purpose of system controlling.
+ * @ref_clk_freq: reference clock frequency selection
+ * @drv_data: driver data available for different SoCs
+ * @phy_usage: usage count for phy
+ * @lock: lock for phy operations
+ */
+struct samsung_usbphy {
+ struct usb_phy phy;
+ struct samsung_usbphy_data *plat;
+ struct device *dev;
+ struct clk *clk;
+ void __iomem *regs;
+ struct regmap *syscon_reg;
+ int ref_clk_freq;
+ const struct samsung_usbphy_drvdata *drv_data;
+ atomic_t phy_usage;
+ spinlock_t lock;
+};
+
+#define phy_to_sphy(x) container_of((x), struct samsung_usbphy, phy)
+
+static const struct of_device_id samsung_usbphy_dt_match[];
+
+static inline const struct samsung_usbphy_drvdata
+*samsung_usbphy_get_driver_data(struct platform_device *pdev)
+{
+ if (pdev->dev.of_node) {
+ const struct of_device_id *match;
+
+ match = of_match_node(samsung_usbphy_dt_match,
+ pdev->dev.of_node);
+ return match->data;
+ }
+
+ return (struct samsung_usbphy_drvdata *)
+ platform_get_device_id(pdev)->driver_data;
+}
--
1.7.10.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH RFC 6/7] usb: host: ehci-exynos: Remove unnecessary usb-phy support
2014-08-14 14:23 [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Vivek Gautam
` (4 preceding siblings ...)
2014-08-14 14:23 ` [PATCH RFC 5/7] usb-phy: samsung-usb2: Clean up to leave only S3C64XX support Vivek Gautam
@ 2014-08-14 14:23 ` Vivek Gautam
[not found] ` <1408026240-28365-7-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
[not found] ` <1408026240-28365-1-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2014-08-20 18:14 ` [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Felipe Balbi
7 siblings, 1 reply; 15+ messages in thread
From: Vivek Gautam @ 2014-08-14 14:23 UTC (permalink / raw)
To: linux-usb, balbi
Cc: linux-kernel, devicetree, grant.likely, gregkh, stern, jg1.han,
s.nawrocki, k.debski, Vivek Gautam
Now that we have completely moved from older USB-PHY drivers
to newer GENERIC-PHY drivers for PHYs available with USB controllers
on Exynos series of SoCs, we can remove the support for the same
in our host drivers too.
This should fix the issue on ehci-exynos, wherein in the absence of
SAMSUNG_USB2PHY config symbol, we ended up getting the NOP_USB_XCEIV phy
when the same is enabled. And thus the PHYs are not configured properly.
Reported-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
---
drivers/usb/host/ehci-exynos.c | 53 ++++++----------------------------------
1 file changed, 8 insertions(+), 45 deletions(-)
diff --git a/drivers/usb/host/ehci-exynos.c b/drivers/usb/host/ehci-exynos.c
index cda0a2f..54944cc 100644
--- a/drivers/usb/host/ehci-exynos.c
+++ b/drivers/usb/host/ehci-exynos.c
@@ -21,11 +21,8 @@
#include <linux/of_gpio.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
-#include <linux/usb/phy.h>
-#include <linux/usb/samsung_usb_phy.h>
#include <linux/usb.h>
#include <linux/usb/hcd.h>
-#include <linux/usb/otg.h>
#include "ehci.h"
@@ -47,9 +44,7 @@ static struct hc_driver __read_mostly exynos_ehci_hc_driver;
struct exynos_ehci_hcd {
struct clk *clk;
- struct usb_phy *phy;
- struct usb_otg *otg;
- struct phy *phy_g[PHY_NUMBER];
+ struct phy *phy[PHY_NUMBER];
};
#define to_exynos_ehci(hcd) (struct exynos_ehci_hcd *)(hcd_to_ehci(hcd)->priv)
@@ -62,18 +57,6 @@ static int exynos_ehci_get_phy(struct device *dev,
int phy_number;
int ret = 0;
- exynos_ehci->phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
- if (IS_ERR(exynos_ehci->phy)) {
- ret = PTR_ERR(exynos_ehci->phy);
- if (ret != -ENXIO && ret != -ENODEV) {
- dev_err(dev, "no usb2 phy configured\n");
- return ret;
- }
- dev_dbg(dev, "Failed to get usb2 phy\n");
- } else {
- exynos_ehci->otg = exynos_ehci->phy->otg;
- }
-
for_each_available_child_of_node(dev->of_node, child) {
ret = of_property_read_u32(child, "reg", &phy_number);
if (ret) {
@@ -98,7 +81,7 @@ static int exynos_ehci_get_phy(struct device *dev,
}
dev_dbg(dev, "Failed to get usb2 phy\n");
}
- exynos_ehci->phy_g[phy_number] = phy;
+ exynos_ehci->phy[phy_number] = phy;
}
return ret;
@@ -111,16 +94,13 @@ static int exynos_ehci_phy_enable(struct device *dev)
int i;
int ret = 0;
- if (!IS_ERR(exynos_ehci->phy))
- return usb_phy_init(exynos_ehci->phy);
-
for (i = 0; ret == 0 && i < PHY_NUMBER; i++)
- if (!IS_ERR(exynos_ehci->phy_g[i]))
- ret = phy_power_on(exynos_ehci->phy_g[i]);
+ if (!IS_ERR(exynos_ehci->phy[i]))
+ ret = phy_power_on(exynos_ehci->phy[i]);
if (ret)
for (i--; i >= 0; i--)
- if (!IS_ERR(exynos_ehci->phy_g[i]))
- phy_power_off(exynos_ehci->phy_g[i]);
+ if (!IS_ERR(exynos_ehci->phy[i]))
+ phy_power_off(exynos_ehci->phy[i]);
return ret;
}
@@ -131,14 +111,9 @@ static void exynos_ehci_phy_disable(struct device *dev)
struct exynos_ehci_hcd *exynos_ehci = to_exynos_ehci(hcd);
int i;
- if (!IS_ERR(exynos_ehci->phy)) {
- usb_phy_shutdown(exynos_ehci->phy);
- return;
- }
-
for (i = 0; i < PHY_NUMBER; i++)
- if (!IS_ERR(exynos_ehci->phy_g[i]))
- phy_power_off(exynos_ehci->phy_g[i]);
+ if (!IS_ERR(exynos_ehci->phy[i]))
+ phy_power_off(exynos_ehci->phy[i]);
}
static void exynos_setup_vbus_gpio(struct device *dev)
@@ -231,9 +206,6 @@ skip_phy:
goto fail_io;
}
- if (exynos_ehci->otg)
- exynos_ehci->otg->set_host(exynos_ehci->otg, &hcd->self);
-
err = exynos_ehci_phy_enable(&pdev->dev);
if (err) {
dev_err(&pdev->dev, "Failed to enable USB phy\n");
@@ -273,9 +245,6 @@ static int exynos_ehci_remove(struct platform_device *pdev)
usb_remove_hcd(hcd);
- if (exynos_ehci->otg)
- exynos_ehci->otg->set_host(exynos_ehci->otg, &hcd->self);
-
exynos_ehci_phy_disable(&pdev->dev);
clk_disable_unprepare(exynos_ehci->clk);
@@ -298,9 +267,6 @@ static int exynos_ehci_suspend(struct device *dev)
if (rc)
return rc;
- if (exynos_ehci->otg)
- exynos_ehci->otg->set_host(exynos_ehci->otg, &hcd->self);
-
exynos_ehci_phy_disable(dev);
clk_disable_unprepare(exynos_ehci->clk);
@@ -316,9 +282,6 @@ static int exynos_ehci_resume(struct device *dev)
clk_prepare_enable(exynos_ehci->clk);
- if (exynos_ehci->otg)
- exynos_ehci->otg->set_host(exynos_ehci->otg, &hcd->self);
-
ret = exynos_ehci_phy_enable(dev);
if (ret) {
dev_err(dev, "Failed to enable USB phy\n");
--
1.7.10.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH RFC 7/7] usb: host: ohci-exynos: Remove unnecessary usb-phy support
[not found] ` <1408026240-28365-1-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
@ 2014-08-14 14:24 ` Vivek Gautam
2014-08-15 15:22 ` Alan Stern
[not found] ` <1408026240-28365-8-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
0 siblings, 2 replies; 15+ messages in thread
From: Vivek Gautam @ 2014-08-14 14:24 UTC (permalink / raw)
To: linux-usb-u79uwXL29TY76Z2rM5mHXA, balbi-l0cyMroinI0
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
grant.likely-QSEj5FYQhm4dnm+yROfE0A,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
stern-nwvwT67g6+6dFdvTe/nMLpVzexx5G7lz,
jg1.han-Sze3O3UU22JBDgjK7y7TUQ, s.nawrocki-Sze3O3UU22JBDgjK7y7TUQ,
k.debski-Sze3O3UU22JBDgjK7y7TUQ, Vivek Gautam
Now that we have completely moved from older USB-PHY drivers
to newer GENERIC-PHY drivers for PHYs available with USB controllers
on Exynos series of SoCs, we can remove the support for the same
in our host drivers too.
This should fix the issue on ohci-exynos, wherein in the absence of
SAMSUNG_USB2PHY config symbol, we ended up getting the NOP_USB_XCEIV phy
when the same is enabled. And thus the PHYs are not configured properly.
Reported-by: Sachin Kamat <sachin.kamat-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Vivek Gautam <gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
---
drivers/usb/host/ohci-exynos.c | 64 ++++++----------------------------------
1 file changed, 9 insertions(+), 55 deletions(-)
diff --git a/drivers/usb/host/ohci-exynos.c b/drivers/usb/host/ohci-exynos.c
index a72ab8f..0199a8b 100644
--- a/drivers/usb/host/ohci-exynos.c
+++ b/drivers/usb/host/ohci-exynos.c
@@ -19,11 +19,8 @@
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/phy/phy.h>
-#include <linux/usb/phy.h>
-#include <linux/usb/samsung_usb_phy.h>
#include <linux/usb.h>
#include <linux/usb/hcd.h>
-#include <linux/usb/otg.h>
#include "ohci.h"
@@ -38,9 +35,7 @@ static struct hc_driver __read_mostly exynos_ohci_hc_driver;
struct exynos_ohci_hcd {
struct clk *clk;
- struct usb_phy *phy;
- struct usb_otg *otg;
- struct phy *phy_g[PHY_NUMBER];
+ struct phy *phy[PHY_NUMBER];
};
static int exynos_ohci_get_phy(struct device *dev,
@@ -51,28 +46,7 @@ static int exynos_ohci_get_phy(struct device *dev,
int phy_number;
int ret = 0;
- exynos_ohci->phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
- if (IS_ERR(exynos_ohci->phy)) {
- ret = PTR_ERR(exynos_ohci->phy);
- if (ret != -ENXIO && ret != -ENODEV) {
- dev_err(dev, "no usb2 phy configured\n");
- return ret;
- }
- dev_dbg(dev, "Failed to get usb2 phy\n");
- } else {
- exynos_ohci->otg = exynos_ohci->phy->otg;
- }
-
- /*
- * Getting generic phy:
- * We are keeping both types of phys as a part of transiting OHCI
- * to generic phy framework, so as to maintain backward compatibilty
- * with old DTB.
- * If there are existing devices using DTB files built from them,
- * to remove the support for old bindings in this driver,
- * we need to make sure that such devices have their DTBs
- * updated to ones built from new DTS.
- */
+ /* Get the generic phys */
for_each_available_child_of_node(dev->of_node, child) {
ret = of_property_read_u32(child, "reg", &phy_number);
if (ret) {
@@ -97,7 +71,7 @@ static int exynos_ohci_get_phy(struct device *dev,
}
dev_dbg(dev, "Failed to get usb2 phy\n");
}
- exynos_ohci->phy_g[phy_number] = phy;
+ exynos_ohci->phy[phy_number] = phy;
}
return ret;
@@ -110,16 +84,13 @@ static int exynos_ohci_phy_enable(struct device *dev)
int i;
int ret = 0;
- if (!IS_ERR(exynos_ohci->phy))
- return usb_phy_init(exynos_ohci->phy);
-
for (i = 0; ret == 0 && i < PHY_NUMBER; i++)
- if (!IS_ERR(exynos_ohci->phy_g[i]))
- ret = phy_power_on(exynos_ohci->phy_g[i]);
+ if (!IS_ERR(exynos_ohci->phy[i]))
+ ret = phy_power_on(exynos_ohci->phy[i]);
if (ret)
for (i--; i >= 0; i--)
- if (!IS_ERR(exynos_ohci->phy_g[i]))
- phy_power_off(exynos_ohci->phy_g[i]);
+ if (!IS_ERR(exynos_ohci->phy[i]))
+ phy_power_off(exynos_ohci->phy[i]);
return ret;
}
@@ -130,14 +101,9 @@ static void exynos_ohci_phy_disable(struct device *dev)
struct exynos_ohci_hcd *exynos_ohci = to_exynos_ohci(hcd);
int i;
- if (!IS_ERR(exynos_ohci->phy)) {
- usb_phy_shutdown(exynos_ohci->phy);
- return;
- }
-
for (i = 0; i < PHY_NUMBER; i++)
- if (!IS_ERR(exynos_ohci->phy_g[i]))
- phy_power_off(exynos_ohci->phy_g[i]);
+ if (!IS_ERR(exynos_ohci->phy[i]))
+ phy_power_off(exynos_ohci->phy[i]);
}
static int exynos_ohci_probe(struct platform_device *pdev)
@@ -209,9 +175,6 @@ skip_phy:
goto fail_io;
}
- if (exynos_ohci->otg)
- exynos_ohci->otg->set_host(exynos_ohci->otg, &hcd->self);
-
platform_set_drvdata(pdev, hcd);
err = exynos_ohci_phy_enable(&pdev->dev);
@@ -244,9 +207,6 @@ static int exynos_ohci_remove(struct platform_device *pdev)
usb_remove_hcd(hcd);
- if (exynos_ohci->otg)
- exynos_ohci->otg->set_host(exynos_ohci->otg, &hcd->self);
-
exynos_ohci_phy_disable(&pdev->dev);
clk_disable_unprepare(exynos_ohci->clk);
@@ -275,9 +235,6 @@ static int exynos_ohci_suspend(struct device *dev)
if (rc)
return rc;
- if (exynos_ohci->otg)
- exynos_ohci->otg->set_host(exynos_ohci->otg, &hcd->self);
-
exynos_ohci_phy_disable(dev);
clk_disable_unprepare(exynos_ohci->clk);
@@ -293,9 +250,6 @@ static int exynos_ohci_resume(struct device *dev)
clk_prepare_enable(exynos_ohci->clk);
- if (exynos_ohci->otg)
- exynos_ohci->otg->set_host(exynos_ohci->otg, &hcd->self);
-
ret = exynos_ohci_phy_enable(dev);
if (ret) {
dev_err(dev, "Failed to enable USB phy\n");
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH RFC 6/7] usb: host: ehci-exynos: Remove unnecessary usb-phy support
[not found] ` <1408026240-28365-7-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
@ 2014-08-15 15:22 ` Alan Stern
2014-08-18 1:36 ` Jingoo Han
1 sibling, 0 replies; 15+ messages in thread
From: Alan Stern @ 2014-08-15 15:22 UTC (permalink / raw)
To: Vivek Gautam
Cc: linux-usb-u79uwXL29TY76Z2rM5mHXA, balbi-l0cyMroinI0,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
grant.likely-QSEj5FYQhm4dnm+yROfE0A,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
jg1.han-Sze3O3UU22JBDgjK7y7TUQ, s.nawrocki-Sze3O3UU22JBDgjK7y7TUQ,
k.debski-Sze3O3UU22JBDgjK7y7TUQ
On Thu, 14 Aug 2014, Vivek Gautam wrote:
> Now that we have completely moved from older USB-PHY drivers
> to newer GENERIC-PHY drivers for PHYs available with USB controllers
> on Exynos series of SoCs, we can remove the support for the same
> in our host drivers too.
> This should fix the issue on ehci-exynos, wherein in the absence of
> SAMSUNG_USB2PHY config symbol, we ended up getting the NOP_USB_XCEIV phy
> when the same is enabled. And thus the PHYs are not configured properly.
>
> Reported-by: Sachin Kamat <sachin.kamat-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> Signed-off-by: Vivek Gautam <gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Acked-by: Alan Stern <stern-nwvwT67g6+6dFdvTe/nMLpVzexx5G7lz@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH RFC 7/7] usb: host: ohci-exynos: Remove unnecessary usb-phy support
2014-08-14 14:24 ` [PATCH RFC 7/7] usb: host: ohci-exynos: " Vivek Gautam
@ 2014-08-15 15:22 ` Alan Stern
[not found] ` <1408026240-28365-8-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
1 sibling, 0 replies; 15+ messages in thread
From: Alan Stern @ 2014-08-15 15:22 UTC (permalink / raw)
To: Vivek Gautam
Cc: linux-usb, balbi, linux-kernel, devicetree, grant.likely, gregkh,
jg1.han, s.nawrocki, k.debski
On Thu, 14 Aug 2014, Vivek Gautam wrote:
> Now that we have completely moved from older USB-PHY drivers
> to newer GENERIC-PHY drivers for PHYs available with USB controllers
> on Exynos series of SoCs, we can remove the support for the same
> in our host drivers too.
> This should fix the issue on ohci-exynos, wherein in the absence of
> SAMSUNG_USB2PHY config symbol, we ended up getting the NOP_USB_XCEIV phy
> when the same is enabled. And thus the PHYs are not configured properly.
>
> Reported-by: Sachin Kamat <sachin.kamat@samsung.com>
> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH 1/7] usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver
2014-08-14 14:23 ` [PATCH 1/7] usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver Vivek Gautam
@ 2014-08-18 1:34 ` Jingoo Han
0 siblings, 0 replies; 15+ messages in thread
From: Jingoo Han @ 2014-08-18 1:34 UTC (permalink / raw)
To: 'Vivek Gautam', 'Felipe Balbi'
Cc: linux-usb, linux-kernel, devicetree, grant.likely, gregkh, stern,
s.nawrocki, k.debski, 'Jingoo Han'
On Thursday, August 14, 2014 11:24 PM, Vivek Gautam wrote:
>
> Removing this older USB 3.0 DRD controller PHY driver, since
> a new driver based on generic phy framework is now available.
>
> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Best regards,
Jingoo Han
> ---
> drivers/usb/phy/Kconfig | 8 -
> drivers/usb/phy/Makefile | 1 -
> drivers/usb/phy/phy-samsung-usb.h | 80 ---------
> drivers/usb/phy/phy-samsung-usb3.c | 350 ------------------------------------
> 4 files changed, 439 deletions(-)
> delete mode 100644 drivers/usb/phy/phy-samsung-usb3.c
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH RFC 6/7] usb: host: ehci-exynos: Remove unnecessary usb-phy support
[not found] ` <1408026240-28365-7-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2014-08-15 15:22 ` Alan Stern
@ 2014-08-18 1:36 ` Jingoo Han
1 sibling, 0 replies; 15+ messages in thread
From: Jingoo Han @ 2014-08-18 1:36 UTC (permalink / raw)
To: 'Vivek Gautam'
Cc: linux-usb-u79uwXL29TY76Z2rM5mHXA, balbi-l0cyMroinI0,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
grant.likely-QSEj5FYQhm4dnm+yROfE0A,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
stern-nwvwT67g6+6dFdvTe/nMLpVzexx5G7lz,
s.nawrocki-Sze3O3UU22JBDgjK7y7TUQ,
k.debski-Sze3O3UU22JBDgjK7y7TUQ, 'Jingoo Han'
On Thursday, August 14, 2014 11:24 PM, Vivek Gautam wrote:
>
> Now that we have completely moved from older USB-PHY drivers
> to newer GENERIC-PHY drivers for PHYs available with USB controllers
> on Exynos series of SoCs, we can remove the support for the same
> in our host drivers too.
> This should fix the issue on ehci-exynos, wherein in the absence of
> SAMSUNG_USB2PHY config symbol, we ended up getting the NOP_USB_XCEIV phy
> when the same is enabled. And thus the PHYs are not configured properly.
>
> Reported-by: Sachin Kamat <sachin.kamat-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> Signed-off-by: Vivek Gautam <gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Reviewed-by: Jingoo Han <jg1.han-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Best regards,
Jingoo Han
> ---
> drivers/usb/host/ehci-exynos.c | 53 ++++++----------------------------------
> 1 file changed, 8 insertions(+), 45 deletions(-)
>
> diff --git a/drivers/usb/host/ehci-exynos.c b/drivers/usb/host/ehci-exynos.c
> index cda0a2f..54944cc 100644
> --- a/drivers/usb/host/ehci-exynos.c
> +++ b/drivers/usb/host/ehci-exynos.c
> @@ -21,11 +21,8 @@
> #include <linux/of_gpio.h>
> #include <linux/phy/phy.h>
> #include <linux/platform_device.h>
> -#include <linux/usb/phy.h>
> -#include <linux/usb/samsung_usb_phy.h>
> #include <linux/usb.h>
> #include <linux/usb/hcd.h>
> -#include <linux/usb/otg.h>
>
> #include "ehci.h"
>
> @@ -47,9 +44,7 @@ static struct hc_driver __read_mostly exynos_ehci_hc_driver;
>
> struct exynos_ehci_hcd {
> struct clk *clk;
> - struct usb_phy *phy;
> - struct usb_otg *otg;
> - struct phy *phy_g[PHY_NUMBER];
> + struct phy *phy[PHY_NUMBER];
> };
>
> #define to_exynos_ehci(hcd) (struct exynos_ehci_hcd *)(hcd_to_ehci(hcd)->priv)
> @@ -62,18 +57,6 @@ static int exynos_ehci_get_phy(struct device *dev,
> int phy_number;
> int ret = 0;
>
> - exynos_ehci->phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
> - if (IS_ERR(exynos_ehci->phy)) {
> - ret = PTR_ERR(exynos_ehci->phy);
> - if (ret != -ENXIO && ret != -ENODEV) {
> - dev_err(dev, "no usb2 phy configured\n");
> - return ret;
> - }
> - dev_dbg(dev, "Failed to get usb2 phy\n");
> - } else {
> - exynos_ehci->otg = exynos_ehci->phy->otg;
> - }
> -
> for_each_available_child_of_node(dev->of_node, child) {
> ret = of_property_read_u32(child, "reg", &phy_number);
> if (ret) {
> @@ -98,7 +81,7 @@ static int exynos_ehci_get_phy(struct device *dev,
> }
> dev_dbg(dev, "Failed to get usb2 phy\n");
> }
> - exynos_ehci->phy_g[phy_number] = phy;
> + exynos_ehci->phy[phy_number] = phy;
> }
>
> return ret;
> @@ -111,16 +94,13 @@ static int exynos_ehci_phy_enable(struct device *dev)
> int i;
> int ret = 0;
>
> - if (!IS_ERR(exynos_ehci->phy))
> - return usb_phy_init(exynos_ehci->phy);
> -
> for (i = 0; ret == 0 && i < PHY_NUMBER; i++)
> - if (!IS_ERR(exynos_ehci->phy_g[i]))
> - ret = phy_power_on(exynos_ehci->phy_g[i]);
> + if (!IS_ERR(exynos_ehci->phy[i]))
> + ret = phy_power_on(exynos_ehci->phy[i]);
> if (ret)
> for (i--; i >= 0; i--)
> - if (!IS_ERR(exynos_ehci->phy_g[i]))
> - phy_power_off(exynos_ehci->phy_g[i]);
> + if (!IS_ERR(exynos_ehci->phy[i]))
> + phy_power_off(exynos_ehci->phy[i]);
>
> return ret;
> }
> @@ -131,14 +111,9 @@ static void exynos_ehci_phy_disable(struct device *dev)
> struct exynos_ehci_hcd *exynos_ehci = to_exynos_ehci(hcd);
> int i;
>
> - if (!IS_ERR(exynos_ehci->phy)) {
> - usb_phy_shutdown(exynos_ehci->phy);
> - return;
> - }
> -
> for (i = 0; i < PHY_NUMBER; i++)
> - if (!IS_ERR(exynos_ehci->phy_g[i]))
> - phy_power_off(exynos_ehci->phy_g[i]);
> + if (!IS_ERR(exynos_ehci->phy[i]))
> + phy_power_off(exynos_ehci->phy[i]);
> }
>
> static void exynos_setup_vbus_gpio(struct device *dev)
> @@ -231,9 +206,6 @@ skip_phy:
> goto fail_io;
> }
>
> - if (exynos_ehci->otg)
> - exynos_ehci->otg->set_host(exynos_ehci->otg, &hcd->self);
> -
> err = exynos_ehci_phy_enable(&pdev->dev);
> if (err) {
> dev_err(&pdev->dev, "Failed to enable USB phy\n");
> @@ -273,9 +245,6 @@ static int exynos_ehci_remove(struct platform_device *pdev)
>
> usb_remove_hcd(hcd);
>
> - if (exynos_ehci->otg)
> - exynos_ehci->otg->set_host(exynos_ehci->otg, &hcd->self);
> -
> exynos_ehci_phy_disable(&pdev->dev);
>
> clk_disable_unprepare(exynos_ehci->clk);
> @@ -298,9 +267,6 @@ static int exynos_ehci_suspend(struct device *dev)
> if (rc)
> return rc;
>
> - if (exynos_ehci->otg)
> - exynos_ehci->otg->set_host(exynos_ehci->otg, &hcd->self);
> -
> exynos_ehci_phy_disable(dev);
>
> clk_disable_unprepare(exynos_ehci->clk);
> @@ -316,9 +282,6 @@ static int exynos_ehci_resume(struct device *dev)
>
> clk_prepare_enable(exynos_ehci->clk);
>
> - if (exynos_ehci->otg)
> - exynos_ehci->otg->set_host(exynos_ehci->otg, &hcd->self);
> -
> ret = exynos_ehci_phy_enable(dev);
> if (ret) {
> dev_err(dev, "Failed to enable USB phy\n");
> --
> 1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH RFC 7/7] usb: host: ohci-exynos: Remove unnecessary usb-phy support
[not found] ` <1408026240-28365-8-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
@ 2014-08-18 1:36 ` Jingoo Han
0 siblings, 0 replies; 15+ messages in thread
From: Jingoo Han @ 2014-08-18 1:36 UTC (permalink / raw)
To: 'Vivek Gautam'
Cc: linux-usb-u79uwXL29TY76Z2rM5mHXA, balbi-l0cyMroinI0,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
grant.likely-QSEj5FYQhm4dnm+yROfE0A,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
stern-nwvwT67g6+6dFdvTe/nMLpVzexx5G7lz,
s.nawrocki-Sze3O3UU22JBDgjK7y7TUQ,
k.debski-Sze3O3UU22JBDgjK7y7TUQ, 'Jingoo Han'
On Thursday, August 14, 2014 11:24 PM, Vivek Gautam wrote:
>
> Now that we have completely moved from older USB-PHY drivers
> to newer GENERIC-PHY drivers for PHYs available with USB controllers
> on Exynos series of SoCs, we can remove the support for the same
> in our host drivers too.
> This should fix the issue on ohci-exynos, wherein in the absence of
> SAMSUNG_USB2PHY config symbol, we ended up getting the NOP_USB_XCEIV phy
> when the same is enabled. And thus the PHYs are not configured properly.
>
> Reported-by: Sachin Kamat <sachin.kamat-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> Signed-off-by: Vivek Gautam <gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Reviewed-by: Jingoo Han <jg1.han-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Best regards,
Jingoo Han
> ---
> drivers/usb/host/ohci-exynos.c | 64 ++++++----------------------------------
> 1 file changed, 9 insertions(+), 55 deletions(-)
>
> diff --git a/drivers/usb/host/ohci-exynos.c b/drivers/usb/host/ohci-exynos.c
> index a72ab8f..0199a8b 100644
> --- a/drivers/usb/host/ohci-exynos.c
> +++ b/drivers/usb/host/ohci-exynos.c
> @@ -19,11 +19,8 @@
> #include <linux/of.h>
> #include <linux/platform_device.h>
> #include <linux/phy/phy.h>
> -#include <linux/usb/phy.h>
> -#include <linux/usb/samsung_usb_phy.h>
> #include <linux/usb.h>
> #include <linux/usb/hcd.h>
> -#include <linux/usb/otg.h>
>
> #include "ohci.h"
>
> @@ -38,9 +35,7 @@ static struct hc_driver __read_mostly exynos_ohci_hc_driver;
>
> struct exynos_ohci_hcd {
> struct clk *clk;
> - struct usb_phy *phy;
> - struct usb_otg *otg;
> - struct phy *phy_g[PHY_NUMBER];
> + struct phy *phy[PHY_NUMBER];
> };
>
> static int exynos_ohci_get_phy(struct device *dev,
> @@ -51,28 +46,7 @@ static int exynos_ohci_get_phy(struct device *dev,
> int phy_number;
> int ret = 0;
>
> - exynos_ohci->phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
> - if (IS_ERR(exynos_ohci->phy)) {
> - ret = PTR_ERR(exynos_ohci->phy);
> - if (ret != -ENXIO && ret != -ENODEV) {
> - dev_err(dev, "no usb2 phy configured\n");
> - return ret;
> - }
> - dev_dbg(dev, "Failed to get usb2 phy\n");
> - } else {
> - exynos_ohci->otg = exynos_ohci->phy->otg;
> - }
> -
> - /*
> - * Getting generic phy:
> - * We are keeping both types of phys as a part of transiting OHCI
> - * to generic phy framework, so as to maintain backward compatibilty
> - * with old DTB.
> - * If there are existing devices using DTB files built from them,
> - * to remove the support for old bindings in this driver,
> - * we need to make sure that such devices have their DTBs
> - * updated to ones built from new DTS.
> - */
> + /* Get the generic phys */
> for_each_available_child_of_node(dev->of_node, child) {
> ret = of_property_read_u32(child, "reg", &phy_number);
> if (ret) {
> @@ -97,7 +71,7 @@ static int exynos_ohci_get_phy(struct device *dev,
> }
> dev_dbg(dev, "Failed to get usb2 phy\n");
> }
> - exynos_ohci->phy_g[phy_number] = phy;
> + exynos_ohci->phy[phy_number] = phy;
> }
>
> return ret;
> @@ -110,16 +84,13 @@ static int exynos_ohci_phy_enable(struct device *dev)
> int i;
> int ret = 0;
>
> - if (!IS_ERR(exynos_ohci->phy))
> - return usb_phy_init(exynos_ohci->phy);
> -
> for (i = 0; ret == 0 && i < PHY_NUMBER; i++)
> - if (!IS_ERR(exynos_ohci->phy_g[i]))
> - ret = phy_power_on(exynos_ohci->phy_g[i]);
> + if (!IS_ERR(exynos_ohci->phy[i]))
> + ret = phy_power_on(exynos_ohci->phy[i]);
> if (ret)
> for (i--; i >= 0; i--)
> - if (!IS_ERR(exynos_ohci->phy_g[i]))
> - phy_power_off(exynos_ohci->phy_g[i]);
> + if (!IS_ERR(exynos_ohci->phy[i]))
> + phy_power_off(exynos_ohci->phy[i]);
>
> return ret;
> }
> @@ -130,14 +101,9 @@ static void exynos_ohci_phy_disable(struct device *dev)
> struct exynos_ohci_hcd *exynos_ohci = to_exynos_ohci(hcd);
> int i;
>
> - if (!IS_ERR(exynos_ohci->phy)) {
> - usb_phy_shutdown(exynos_ohci->phy);
> - return;
> - }
> -
> for (i = 0; i < PHY_NUMBER; i++)
> - if (!IS_ERR(exynos_ohci->phy_g[i]))
> - phy_power_off(exynos_ohci->phy_g[i]);
> + if (!IS_ERR(exynos_ohci->phy[i]))
> + phy_power_off(exynos_ohci->phy[i]);
> }
>
> static int exynos_ohci_probe(struct platform_device *pdev)
> @@ -209,9 +175,6 @@ skip_phy:
> goto fail_io;
> }
>
> - if (exynos_ohci->otg)
> - exynos_ohci->otg->set_host(exynos_ohci->otg, &hcd->self);
> -
> platform_set_drvdata(pdev, hcd);
>
> err = exynos_ohci_phy_enable(&pdev->dev);
> @@ -244,9 +207,6 @@ static int exynos_ohci_remove(struct platform_device *pdev)
>
> usb_remove_hcd(hcd);
>
> - if (exynos_ohci->otg)
> - exynos_ohci->otg->set_host(exynos_ohci->otg, &hcd->self);
> -
> exynos_ohci_phy_disable(&pdev->dev);
>
> clk_disable_unprepare(exynos_ohci->clk);
> @@ -275,9 +235,6 @@ static int exynos_ohci_suspend(struct device *dev)
> if (rc)
> return rc;
>
> - if (exynos_ohci->otg)
> - exynos_ohci->otg->set_host(exynos_ohci->otg, &hcd->self);
> -
> exynos_ohci_phy_disable(dev);
>
> clk_disable_unprepare(exynos_ohci->clk);
> @@ -293,9 +250,6 @@ static int exynos_ohci_resume(struct device *dev)
>
> clk_prepare_enable(exynos_ohci->clk);
>
> - if (exynos_ohci->otg)
> - exynos_ohci->otg->set_host(exynos_ohci->otg, &hcd->self);
> -
> ret = exynos_ohci_phy_enable(dev);
> if (ret) {
> dev_err(dev, "Failed to enable USB phy\n");
> --
> 1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers
2014-08-14 14:23 [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Vivek Gautam
` (6 preceding siblings ...)
[not found] ` <1408026240-28365-1-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
@ 2014-08-20 18:14 ` Felipe Balbi
[not found] ` <20140820181406.GA6023-HgARHv6XitL9zxVx7UNMDg@public.gmane.org>
7 siblings, 1 reply; 15+ messages in thread
From: Felipe Balbi @ 2014-08-20 18:14 UTC (permalink / raw)
To: Vivek Gautam
Cc: linux-usb, balbi, linux-kernel, devicetree, grant.likely, gregkh,
stern, jg1.han, s.nawrocki, k.debski
[-- Attachment #1: Type: text/plain, Size: 1684 bytes --]
Hi,
On Thu, Aug 14, 2014 at 07:53:53PM +0530, Vivek Gautam wrote:
> - This series is based on 'usb-next' branch.
>
> Now that we have support for USB PHY controllers for Exynos SoC series,
> we are free to remove the older usb-phy support.
> In the process, we are removing the entire phy-samsung-usb3 driver, and
> besides that all support for Exynos4x and Exynos5 from phy-samsung-usb2
> driver.
>
> We have also removed the older USB-PHY support from ehci-exynos and ohci-exynos
> since those drivers now can use newer GENERIC-PHYs, and don't need the older
> USB-PHYs and related code anymore. These patches for ohci-exynos and ehci-exynos
> now replaces the older sent patch for phy sequence cleanup for them.[1]
>
> I have build-tested this series for exynos_defconfig and s3c64xx_defconfig,
> and have tested the EHCI and OHCI operations on smdk5250 board, but
> have not tested the actual working due to unavailability of S3C64XX
> board. So can someone please help me testing this series.
>
> [1] https://lkml.org/lkml/2014/8/5/142
>
> Vivek Gautam (7):
> usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver
> usb-phy: samsung-usb2: Remove support for Exynos5250
> usb-phy: samsung-usb2: Remove support for Exynos4X12
> usb-phy: samsung-usb2: Remove support for Exynos4210
> usb-phy: samsung-usb2: Clean up to leave only S3C64XX support
> usb: host: ehci-exynos: Remove unnecessary usb-phy support
> usb: host: ohci-exynos: Remove unnecessary usb-phy support
some of these patches are still RFC, can you resend without RFC and all
proper Acks in place ? Also rebased on top of v3.17-rc1.
thanks
--
balbi
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers
[not found] ` <20140820181406.GA6023-HgARHv6XitL9zxVx7UNMDg@public.gmane.org>
@ 2014-08-21 4:37 ` Vivek Gautam
0 siblings, 0 replies; 15+ messages in thread
From: Vivek Gautam @ 2014-08-21 4:37 UTC (permalink / raw)
To: Felipe Balbi
Cc: Linux USB Mailing List,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Grant Likely,
Greg KH, Alan Stern, Jingoo Han, Sylwester Nawrocki, Kamil Debski
Hi Felipe,
On Wed, Aug 20, 2014 at 11:44 PM, Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org> wrote:
> Hi,
>
> On Thu, Aug 14, 2014 at 07:53:53PM +0530, Vivek Gautam wrote:
>> - This series is based on 'usb-next' branch.
>>
>> Now that we have support for USB PHY controllers for Exynos SoC series,
>> we are free to remove the older usb-phy support.
>> In the process, we are removing the entire phy-samsung-usb3 driver, and
>> besides that all support for Exynos4x and Exynos5 from phy-samsung-usb2
>> driver.
>>
>> We have also removed the older USB-PHY support from ehci-exynos and ohci-exynos
>> since those drivers now can use newer GENERIC-PHYs, and don't need the older
>> USB-PHYs and related code anymore. These patches for ohci-exynos and ehci-exynos
>> now replaces the older sent patch for phy sequence cleanup for them.[1]
>>
>> I have build-tested this series for exynos_defconfig and s3c64xx_defconfig,
>> and have tested the EHCI and OHCI operations on smdk5250 board, but
>> have not tested the actual working due to unavailability of S3C64XX
>> board. So can someone please help me testing this series.
>>
>> [1] https://lkml.org/lkml/2014/8/5/142
>>
>> Vivek Gautam (7):
>> usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver
>> usb-phy: samsung-usb2: Remove support for Exynos5250
>> usb-phy: samsung-usb2: Remove support for Exynos4X12
>> usb-phy: samsung-usb2: Remove support for Exynos4210
>> usb-phy: samsung-usb2: Clean up to leave only S3C64XX support
>> usb: host: ehci-exynos: Remove unnecessary usb-phy support
>> usb: host: ohci-exynos: Remove unnecessary usb-phy support
>
> some of these patches are still RFC, can you resend without RFC and all
> proper Acks in place ? Also rebased on top of v3.17-rc1.
As per the discussion in thread [1], i am dropping the [Patch 1/7]
till [Patch 5/7] since
these are part of the cleanup series by Bart: [PATCH 0/5] usb: phy:
samsung: remove old USB PHY code;
and will send out the rebased remaining two patches with Alan's Ack.
[1] https://lkml.org/lkml/2014/8/21/11
--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2014-08-21 4:37 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-08-14 14:23 [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Vivek Gautam
2014-08-14 14:23 ` [PATCH 1/7] usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver Vivek Gautam
2014-08-18 1:34 ` Jingoo Han
2014-08-14 14:23 ` [PATCH RFC 2/7] usb-phy: samsung-usb2: Remove support for Exynos5250 Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 3/7] usb-phy: samsung-usb2: Remove support for Exynos4X12 Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 4/7] usb-phy: samsung-usb2: Remove support for Exynos4210 Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 5/7] usb-phy: samsung-usb2: Clean up to leave only S3C64XX support Vivek Gautam
2014-08-14 14:23 ` [PATCH RFC 6/7] usb: host: ehci-exynos: Remove unnecessary usb-phy support Vivek Gautam
[not found] ` <1408026240-28365-7-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2014-08-15 15:22 ` Alan Stern
2014-08-18 1:36 ` Jingoo Han
[not found] ` <1408026240-28365-1-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2014-08-14 14:24 ` [PATCH RFC 7/7] usb: host: ohci-exynos: " Vivek Gautam
2014-08-15 15:22 ` Alan Stern
[not found] ` <1408026240-28365-8-git-send-email-gautam.vivek-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2014-08-18 1:36 ` Jingoo Han
2014-08-20 18:14 ` [PATCH 0/7] usb-phy: samsung: Cleanup the unused drivers Felipe Balbi
[not found] ` <20140820181406.GA6023-HgARHv6XitL9zxVx7UNMDg@public.gmane.org>
2014-08-21 4:37 ` Vivek Gautam
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).