[PATCH 0/6] ARM: sunxi: Add basic support for Allwinner A80 SoC

[PATCH 0/6] ARM: sunxi: Add basic support for Allwinner A80 SoC

[Chen-Yu Tsai]

Hi everyone,

This patch series adds very basic support for Allwinner's A80 SoC,
a big.LITTLE architecture with 4 Cortex-A7s and 4 Cortex-A15s.

Development is done on the A80 Optimus Board, the defacto development
board for the A80, with the accompanying SDK as a reference. 

So far I've been unable to get the board to boot from MMC, or
using Android fastboot. I'm using Allwinner's FEL mode to load
the bootloader and kernel+dtb image over USB. Notes on my attempts
can be found here: http://linux-sunxi.org/User:Wens#A80_Optimus


Patch 1 introduces the compatible string for the A80.

Patch 2 adds options to use UART0 on the A80 as the debug port for
earlyprintk.

Patch 3 adds a barebone dtsi with just the cpu, memory and uart nodes.

Patch 4 adds a barebone dts for the A80 Optimus Board.

Patch 5 documents the vendor prefix for Merrii Technology Co., Ltd,
the designer and vendor of the A80 Optimus Board.

Patch 6 documents all the Allwinner SoCs we currently support.


Cheers
ChenYu

Chen-Yu Tsai (6):
  ARM: sunxi: Introduce Allwinner A80 support
  ARM: sunxi: Add debug uart used by sun9i (Allwinner A80)
  ARM: dts: sunxi: Add Allwinner A80 dtsi
  ARM: dts: sun9i: Add A80 Optimus Board support
  devicetree: bindings: Add vendor prefix for Merrii Technology Co.,
    Ltd.
  devicetree: bindings: Document supported Allwinner sunxi SoCs

 Documentation/devicetree/bindings/arm/sunxi.txt    |  12 +
 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/Kconfig.debug                             |  10 +
 arch/arm/boot/dts/Makefile                         |   2 +
 arch/arm/boot/dts/sun9i-a80-optimus.dts            |  66 +++++
 arch/arm/boot/dts/sun9i-a80.dtsi                   | 280 +++++++++++++++++++++
 arch/arm/mach-sunxi/Kconfig                        |   5 +
 arch/arm/mach-sunxi/sunxi.c                        |   9 +
 8 files changed, 385 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/sunxi.txt
 create mode 100644 arch/arm/boot/dts/sun9i-a80-optimus.dts
 create mode 100644 arch/arm/boot/dts/sun9i-a80.dtsi

-- 
2.1.0

[PATCH 1/6] ARM: sunxi: Introduce Allwinner A80 support

[Chen-Yu Tsai]

The Allwinner A80 is a new Cortex octo-core A7/A15 big.LITTLE SoC.
While it's processor cores and interconnecting bus are new, it
re-uses many peripherals found in earlier Allwinner SoCs.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
 arch/arm/mach-sunxi/Kconfig | 5 +++++
 arch/arm/mach-sunxi/sunxi.c | 9 +++++++++
 2 files changed, 14 insertions(+)

diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index 1aaa1e1..72f222b 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -42,4 +42,9 @@ config MACH_SUN8I
 	select MFD_SUN6I_PRCM
 	select RESET_CONTROLLER
 
+config MACH_SUN9I
+	bool "Allwinner A80 (sun9i) SoCs support"
+	default ARCH_SUNXI
+	select ARM_GIC
+
 endif
diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
index 42d4753..4bd2117 100644
--- a/arch/arm/mach-sunxi/sunxi.c
+++ b/arch/arm/mach-sunxi/sunxi.c
@@ -139,3 +139,12 @@ static const char * const sun8i_board_dt_compat[] = {
 DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
 	.dt_compat	= sun8i_board_dt_compat,
 MACHINE_END
+
+static const char * const sun9i_board_dt_compat[] = {
+	"allwinner,sun9i-a80",
+	NULL,
+};
+
+DT_MACHINE_START(SUN9I_DT, "Allwinner sun9i (A80) Family")
+	.dt_compat	= sun9i_board_dt_compat,
+MACHINE_END
-- 
2.1.0

[PATCH 2/6] ARM: sunxi: Add debug uart used by sun9i (Allwinner A80)

[Chen-Yu Tsai]

The uarts on sun9i are still compatible with the dw_8250, but are
located at different addresses.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
 arch/arm/Kconfig.debug | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index b11ad54..58b5218 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -707,6 +707,14 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on SOCFPGA based platforms.
 
+	config DEBUG_SUN9I_UART0
+		bool "Kernel low-level debugging messages via sun9i UART0"
+		depends on ARCH_SUNXI && MACH_SUN9I
+		select DEBUG_UART_8250
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on Allwinner A80 based platforms on the UART0.
+
 	config DEBUG_SUNXI_UART0
 		bool "Kernel low-level debugging messages via sunXi UART0"
 		depends on ARCH_SUNXI
@@ -1068,6 +1076,7 @@ config DEBUG_UART_PHYS
 	default 0x02530c00 if DEBUG_KEYSTONE_UART0
 	default 0x02531000 if DEBUG_KEYSTONE_UART1
 	default 0x03010fe0 if ARCH_RPC
+	default 0x07000000 if DEBUG_SUN9I_UART0
 	default 0x10009000 if DEBUG_REALVIEW_STD_PORT || DEBUG_CNS3XXX || \
 				DEBUG_VEXPRESS_UART0_CA9
 	default 0x1010c000 if DEBUG_REALVIEW_PB1176_PORT
@@ -1145,6 +1154,7 @@ config DEBUG_UART_VIRT
 	default 0xf2100000 if DEBUG_PXA_UART1
 	default 0xf4090000 if ARCH_LPC32XX
 	default 0xf4200000 if ARCH_GEMINI
+	default 0xf7000000 if DEBUG_SUN9I_UART0
 	default 0xf7000000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART0 || \
 				DEBUG_S3C2410_UART0)
 	default 0xf7004000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART1 || \
-- 
2.1.0

Re: [PATCH 2/6] ARM: sunxi: Add debug uart used by sun9i (Allwinner A80)

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 957 bytes --]

On Sun, Sep 21, 2014 at 10:58:09PM +0800, Chen-Yu Tsai wrote:
> The uarts on sun9i are still compatible with the dw_8250, but are
> located at different addresses.
> 
> Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> ---
>  arch/arm/Kconfig.debug | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
> index b11ad54..58b5218 100644
> --- a/arch/arm/Kconfig.debug
> +++ b/arch/arm/Kconfig.debug
> @@ -707,6 +707,14 @@ choice
>  		  Say Y here if you want kernel low-level debugging support
>  		  on SOCFPGA based platforms.
>  
> +	config DEBUG_SUN9I_UART0
> +		bool "Kernel low-level debugging messages via sun9i UART0"
> +		depends on ARCH_SUNXI && MACH_SUN9I

Depending on MACH_SUN9I should be enough. It already depends on ARCH_SUNXI.

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 3/6] ARM: dts: sunxi: Add Allwinner A80 dtsi

[Chen-Yu Tsai]

The Allwinner A80 is a new multi-purpose SoC with 4 Cortex-A7 and
4 Cortex-A15 cores in a big.LITTLE architecture, and a 64-core
PowerVR G6230 GPU.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
 arch/arm/boot/dts/sun9i-a80.dtsi | 280 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 280 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun9i-a80.dtsi

diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi
new file mode 100644
index 0000000..f23ea59
--- /dev/null
+++ b/arch/arm/boot/dts/sun9i-a80.dtsi
@@ -0,0 +1,280 @@
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this library; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&gic>;
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+		serial5 = &uart5;
+		serial6 = &r_uart;
+	};
+
+	cpu-map {
+		cluster0 {
+			core0 {
+				cpu = <&cpu0>;
+			};
+			core1 {
+				cpu = <&cpu1>;
+			};
+			core2 {
+				cpu = <&cpu2>;
+			};
+			core3 {
+				cpu = <&cpu3>;
+			};
+		};
+
+		cluster1 {
+			core0 {
+				cpu = <&cpu4>;
+			};
+			core1 {
+				cpu = <&cpu5>;
+			};
+			core2 {
+				cpu = <&cpu6>;
+			};
+			core3 {
+				cpu = <&cpu7>;
+			};
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0x0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0x1>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0x2>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0x3>;
+		};
+
+		cpu4: cpu@100 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <0x100>;
+		};
+
+		cpu5: cpu@101 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <0x101>;
+		};
+
+		cpu6: cpu@102 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <0x102>;
+		};
+
+		cpu7: cpu@103 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <0x103>;
+		};
+	};
+
+	memory {
+		reg = <0x20000000 0x40000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: osc32k_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gic: interrupt-controller@01c41000 {
+			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			reg = <0x01c41000 0x1000>,
+			      <0x01c42000 0x1000>,
+			      <0x01c44000 0x2000>,
+			      <0x01c46000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <1 9 0xf04>;
+		};
+
+		timer@06000c00 {
+			compatible = "allwinner,sun4i-a10-timer";
+			reg = <0x06000c00 0xa0>;
+			interrupts = <0 18 4>,
+				     <0 19 4>,
+				     <0 20 4>,
+				     <0 21 4>,
+				     <0 22 4>,
+				     <0 23 4>;
+
+			clocks = <&osc24M>;
+		};
+
+		uart0: serial@07000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x07000000 0x400>;
+			interrupts = <0 0 4>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart1: serial@07000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x07000400 0x400>;
+			interrupts = <0 1 4>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart2: serial@07000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x07000800 0x400>;
+			interrupts = <0 2 4>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart3: serial@07000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x07000c00 0x400>;
+			interrupts = <0 3 4>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart4: serial@07001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x07001000 0x400>;
+			interrupts = <0 4 4>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart5: serial@07001400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x07001400 0x400>;
+			interrupts = <0 5 4>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		r_wdt: watchdog@08001000 {
+			compatible = "allwinner,sun6i-a31-wdt";
+			reg = <0x08001000 0x20>;
+			interrupts = <0 36 4>;
+		};
+
+		r_uart: serial@08002800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x08002800 0x400>;
+			interrupts = <0 38 4>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+	};
+};
-- 
2.1.0

Re: [PATCH 3/6] ARM: dts: sunxi: Add Allwinner A80 dtsi

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 5391 bytes --]

Hi,

Thanks, a lot for your patches :)

On Sun, Sep 21, 2014 at 10:58:10PM +0800, Chen-Yu Tsai wrote:
> The Allwinner A80 is a new multi-purpose SoC with 4 Cortex-A7 and
> 4 Cortex-A15 cores in a big.LITTLE architecture, and a 64-core
> PowerVR G6230 GPU.
> 
> Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun9i-a80.dtsi | 280 +++++++++++++++++++++++++++++++++++++++
>  1 file changed, 280 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun9i-a80.dtsi
> 
> diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi
> new file mode 100644
> index 0000000..f23ea59
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun9i-a80.dtsi
> @@ -0,0 +1,280 @@
> +/*
> + * Copyright 2014 Chen-Yu Tsai
> + *
> + * Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This library is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This library is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + *     You should have received a copy of the GNU General Public
> + *     License along with this library; if not, write to the Free
> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
> + *     MA 02110-1301 USA
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/include/ "skeleton.dtsi"
> +
> +/ {
> +	interrupt-parent = <&gic>;
> +
> +	aliases {
> +		serial0 = &uart0;
> +		serial1 = &uart1;
> +		serial2 = &uart2;
> +		serial3 = &uart3;
> +		serial4 = &uart4;
> +		serial5 = &uart5;
> +		serial6 = &r_uart;
> +	};
> +
> +	cpu-map {
> +		cluster0 {
> +			core0 {
> +				cpu = <&cpu0>;
> +			};
> +			core1 {
> +				cpu = <&cpu1>;
> +			};
> +			core2 {
> +				cpu = <&cpu2>;
> +			};
> +			core3 {
> +				cpu = <&cpu3>;
> +			};

Having separation lines between the cores here would be nice.

> +		};
> +
> +		cluster1 {
> +			core0 {
> +				cpu = <&cpu4>;
> +			};
> +			core1 {
> +				cpu = <&cpu5>;
> +			};
> +			core2 {
> +				cpu = <&cpu6>;
> +			};
> +			core3 {
> +				cpu = <&cpu7>;
> +			};
> +		};
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu0: cpu@0 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0x0>;
> +		};
> +
> +		cpu1: cpu@1 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0x1>;
> +		};
> +
> +		cpu2: cpu@2 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0x2>;
> +		};
> +
> +		cpu3: cpu@3 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0x3>;
> +		};
> +
> +		cpu4: cpu@100 {
> +			compatible = "arm,cortex-a15";
> +			device_type = "cpu";
> +			reg = <0x100>;
> +		};
> +
> +		cpu5: cpu@101 {
> +			compatible = "arm,cortex-a15";
> +			device_type = "cpu";
> +			reg = <0x101>;
> +		};
> +
> +		cpu6: cpu@102 {
> +			compatible = "arm,cortex-a15";
> +			device_type = "cpu";
> +			reg = <0x102>;
> +		};
> +
> +		cpu7: cpu@103 {
> +			compatible = "arm,cortex-a15";
> +			device_type = "cpu";
> +			reg = <0x103>;
> +		};
> +	};
> +
> +	memory {
> +		reg = <0x20000000 0x40000000>;

Usually, what we put there was the maximum amount of RAM that can be
handled by the SoC. I think that it can go above 1GB

It looks fine otherwise, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: Re: [PATCH 3/6] ARM: dts: sunxi: Add Allwinner A80 dtsi

[Chen-Yu Tsai]

On Wed, Sep 24, 2014 at 2:37 PM, Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi,
>
> Thanks, a lot for your patches :)
>
> On Sun, Sep 21, 2014 at 10:58:10PM +0800, Chen-Yu Tsai wrote:
>> The Allwinner A80 is a new multi-purpose SoC with 4 Cortex-A7 and
>> 4 Cortex-A15 cores in a big.LITTLE architecture, and a 64-core
>> PowerVR G6230 GPU.
>>
>> Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
>> ---
>>  arch/arm/boot/dts/sun9i-a80.dtsi | 280 +++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 280 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/sun9i-a80.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi
>> new file mode 100644
>> index 0000000..f23ea59
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun9i-a80.dtsi
>> @@ -0,0 +1,280 @@
>> +/*
>> + * Copyright 2014 Chen-Yu Tsai
>> + *
>> + * Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + *  a) This library is free software; you can redistribute it and/or
>> + *     modify it under the terms of the GNU General Public License as
>> + *     published by the Free Software Foundation; either version 2 of the
>> + *     License, or (at your option) any later version.
>> + *
>> + *     This library is distributed in the hope that it will be useful,
>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *     GNU General Public License for more details.
>> + *
>> + *     You should have received a copy of the GNU General Public
>> + *     License along with this library; if not, write to the Free
>> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
>> + *     MA 02110-1301 USA
>> + *
>> + * Or, alternatively,
>> + *
>> + *  b) Permission is hereby granted, free of charge, to any person
>> + *     obtaining a copy of this software and associated documentation
>> + *     files (the "Software"), to deal in the Software without
>> + *     restriction, including without limitation the rights to use,
>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>> + *     sell copies of the Software, and to permit persons to whom the
>> + *     Software is furnished to do so, subject to the following
>> + *     conditions:
>> + *
>> + *     The above copyright notice and this permission notice shall be
>> + *     included in all copies or substantial portions of the Software.
>> + *
>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + *     OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +/include/ "skeleton.dtsi"
>> +
>> +/ {
>> +     interrupt-parent = <&gic>;
>> +
>> +     aliases {
>> +             serial0 = &uart0;
>> +             serial1 = &uart1;
>> +             serial2 = &uart2;
>> +             serial3 = &uart3;
>> +             serial4 = &uart4;
>> +             serial5 = &uart5;
>> +             serial6 = &r_uart;
>> +     };
>> +
>> +     cpu-map {
>> +             cluster0 {
>> +                     core0 {
>> +                             cpu = <&cpu0>;
>> +                     };
>> +                     core1 {
>> +                             cpu = <&cpu1>;
>> +                     };
>> +                     core2 {
>> +                             cpu = <&cpu2>;
>> +                     };
>> +                     core3 {
>> +                             cpu = <&cpu3>;
>> +                     };
>
> Having separation lines between the cores here would be nice.

OK.

>> +             };
>> +
>> +             cluster1 {
>> +                     core0 {
>> +                             cpu = <&cpu4>;
>> +                     };
>> +                     core1 {
>> +                             cpu = <&cpu5>;
>> +                     };
>> +                     core2 {
>> +                             cpu = <&cpu6>;
>> +                     };
>> +                     core3 {
>> +                             cpu = <&cpu7>;
>> +                     };
>> +             };
>> +     };
>> +
>> +     cpus {
>> +             #address-cells = <1>;
>> +             #size-cells = <0>;
>> +
>> +             cpu0: cpu@0 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x0>;
>> +             };
>> +
>> +             cpu1: cpu@1 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x1>;
>> +             };
>> +
>> +             cpu2: cpu@2 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x2>;
>> +             };
>> +
>> +             cpu3: cpu@3 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x3>;
>> +             };
>> +
>> +             cpu4: cpu@100 {
>> +                     compatible = "arm,cortex-a15";
>> +                     device_type = "cpu";
>> +                     reg = <0x100>;
>> +             };
>> +
>> +             cpu5: cpu@101 {
>> +                     compatible = "arm,cortex-a15";
>> +                     device_type = "cpu";
>> +                     reg = <0x101>;
>> +             };
>> +
>> +             cpu6: cpu@102 {
>> +                     compatible = "arm,cortex-a15";
>> +                     device_type = "cpu";
>> +                     reg = <0x102>;
>> +             };
>> +
>> +             cpu7: cpu@103 {
>> +                     compatible = "arm,cortex-a15";
>> +                     device_type = "cpu";
>> +                     reg = <0x103>;
>> +             };
>> +     };
>> +
>> +     memory {
>> +             reg = <0x20000000 0x40000000>;
>
> Usually, what we put there was the maximum amount of RAM that can be
> handled by the SoC. I think that it can go above 1GB

With LPAE, it can handle 8GB. But the DT won't take 64bit values.
I'm not sure how to get it in. I'll look around for examples.

> It looks fine otherwise, thanks!

Thanks!

ChenYu

Re: Re: [PATCH 3/6] ARM: dts: sunxi: Add Allwinner A80 dtsi

[Gregory CLEMENT]

Hi Chen-Yu,


>>> +
>>> +     memory {
>>> +             reg = <0x20000000 0x40000000>;
>>
>> Usually, what we put there was the maximum amount of RAM that can be
>> handled by the SoC. I think that it can go above 1GB
> 
> With LPAE, it can handle 8GB. But the DT won't take 64bit values.
> I'm not sure how to get it in. I'll look around for examples.

You can have a look on what we did for Armada XP:

arch/arm/boot/dts/armada-370-xp.dtsi
arch/arm/boot/dts/armada-xp.dtsi
arch/arm/boot/dts/armada-xp-gp.dts

I created a skeleton64.dtsi for this case

Gregory


-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

Re: Re: [PATCH 3/6] ARM: dts: sunxi: Add Allwinner A80 dtsi

[Chen-Yu Tsai]

On Wed, Sep 24, 2014 at 3:18 PM, Gregory CLEMENT
<gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi Chen-Yu,
>
>
>>>> +
>>>> +     memory {
>>>> +             reg = <0x20000000 0x40000000>;
>>>
>>> Usually, what we put there was the maximum amount of RAM that can be
>>> handled by the SoC. I think that it can go above 1GB
>>
>> With LPAE, it can handle 8GB. But the DT won't take 64bit values.
>> I'm not sure how to get it in. I'll look around for examples.
>
> You can have a look on what we did for Armada XP:
>
> arch/arm/boot/dts/armada-370-xp.dtsi
> arch/arm/boot/dts/armada-xp.dtsi
> arch/arm/boot/dts/armada-xp-gp.dts
>
> I created a skeleton64.dtsi for this case

Thanks! I was wondering what that was for.

ChenYu

Re: Re: [PATCH 3/6] ARM: dts: sunxi: Add Allwinner A80 dtsi

[Chen-Yu Tsai]

On Wed, Sep 24, 2014 at 3:18 PM, Gregory CLEMENT
<gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi Chen-Yu,
>
>
>>>> +
>>>> +     memory {
>>>> +             reg = <0x20000000 0x40000000>;
>>>
>>> Usually, what we put there was the maximum amount of RAM that can be
>>> handled by the SoC. I think that it can go above 1GB
>>
>> With LPAE, it can handle 8GB. But the DT won't take 64bit values.
>> I'm not sure how to get it in. I'll look around for examples.
>
> You can have a look on what we did for Armada XP:
>
> arch/arm/boot/dts/armada-370-xp.dtsi
> arch/arm/boot/dts/armada-xp.dtsi
> arch/arm/boot/dts/armada-xp-gp.dts
>
> I created a skeleton64.dtsi for this case

Thanks for the tip. Before I send v2, I do have a question. I'm using

    ranges = <0 0 0 0x20000000>;

in the clocks and soc node to avoid having to use 64bit values for all
addresses and sizes. Would this be undesirable, even bad practice maybe?

http://linux-sunxi.org/A80/Memory_map is a document I pieced together
from Allwinner's SDK header files. AFAIK only the memory goes above
the 4GB limit. All peripherals are under 512 MB, 256MB even.


Thanks
ChenYu

Re: Re: [PATCH 3/6] ARM: dts: sunxi: Add Allwinner A80 dtsi

[Gregory CLEMENT]

Hi Chen-Yu,


> 
> Thanks for the tip. Before I send v2, I do have a question. I'm using
> 
>     ranges = <0 0 0 0x20000000>;
> 
> in the clocks and soc node to avoid having to use 64bit values for all
> addresses and sizes. Would this be undesirable, even bad practice maybe?

We did something like that for all the internal registers too as they are all
under 4GB. In our case the use of a range really makes sens because the hardware
addresses were configurable. You don't have such requirement so I can't say if
it is a bad practice. From my point of view it seems sensible but I am not an
DT expert.


Grégory


-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH 4/6] ARM: dts: sun9i: Add A80 Optimus Board support

[Chen-Yu Tsai]

The A80 Optimus Board is was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.

This board has a UART port, a JTAG connector, USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.

This patch adds only basic support.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
 arch/arm/boot/dts/Makefile              |  2 +
 arch/arm/boot/dts/sun9i-a80-optimus.dts | 66 +++++++++++++++++++++++++++++++++
 2 files changed, 68 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun9i-a80-optimus.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 2f42b18..098f319 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -424,6 +424,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-pcduino3.dtb
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-ippo-q8h-v5.dtb
+dtb-$(CONFIG_MACH_SUN9I) += \
+	sun9i-a80-optimus.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra20-iris-512.dtb \
 	tegra20-medcom-wide.dtb \
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
new file mode 100644
index 0000000..b46391a
--- /dev/null
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -0,0 +1,66 @@
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this library; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "sun9i-a80.dtsi"
+
+/ {
+	model = "Merrii A80 Optimus Board";
+	compatible = "merrii,a80-optimus", "allwinner,sun9i-a80";
+
+	chosen {
+		bootargs = "earlyprintk console=ttyS0,115200";
+	};
+
+	soc@00000000 {
+		uart0: serial@07000000 {
+			status = "okay";
+		};
+	};
+};
-- 
2.1.0

[PATCH 5/6] devicetree: bindings: Add vendor prefix for Merrii Technology Co., Ltd.

[Chen-Yu Tsai]

Merrii Technology Co., Ltd. is a Chinese ARM integration developer that
specializes in Allwinner SoC based designs.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index ac7269f..d3a96ac 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -81,6 +81,7 @@ lltc	Linear Technology Corporation
 marvell	Marvell Technology Group Ltd.
 maxim	Maxim Integrated Products
 mediatek	MediaTek Inc.
+merrii	Merrii Technology Co., Ltd.
 micrel	Micrel Inc.
 microchip	Microchip Technology Inc.
 mosaixtech	Mosaix Technologies, Inc.
-- 
2.1.0

[PATCH 6/6] devicetree: bindings: Document supported Allwinner sunxi SoCs

[Chen-Yu Tsai]

This adds a list of supported Allwinner SoC bindings.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
 Documentation/devicetree/bindings/arm/sunxi.txt | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/sunxi.txt

diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
new file mode 100644
index 0000000..d7d1039
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -0,0 +1,12 @@
+Allwinner sunXi Platforms Device Tree Bindings
+
+Each device tree must specify which Allwinner SoC it uses,
+using one of the following compatible stirngs:
+
+  allwinner,sun4i-a10
+  allwinner,sun5i-a10s
+  allwinner,sun5i-a13
+  allwinner,sun6i-a31
+  allwinner,sun7i-a20
+  allwinner,sun8i-a23
+  allwinner,sun9i-a80
-- 
2.1.0

Re: [PATCH 0/6] ARM: sunxi: Add basic support for Allwinner A80 SoC

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1070 bytes --]

Hi Chen-Yu,

On Sun, Sep 21, 2014 at 10:58:07PM +0800, Chen-Yu Tsai wrote:
> Hi everyone,
> 
> This patch series adds very basic support for Allwinner's A80 SoC,
> a big.LITTLE architecture with 4 Cortex-A7s and 4 Cortex-A15s.
> 
> Development is done on the A80 Optimus Board, the defacto development
> board for the A80, with the accompanying SDK as a reference. 
> 
> So far I've been unable to get the board to boot from MMC, or
> using Android fastboot. I'm using Allwinner's FEL mode to load
> the bootloader and kernel+dtb image over USB. Notes on my attempts
> can be found here: http://linux-sunxi.org/User:Wens#A80_Optimus

It looks very nice, thanks a lot. You'll find a minor comments inline.

One thing I forgot to ask you about when doing the A23, and that would
nice to do is to update the documentation we have in
Documentation/arm/sunxi/README with the A23 and A80 infos you've been
able to gather.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH 0/6] ARM: sunxi: Add basic support for Allwinner A80 SoC

[Chen-Yu Tsai]

Hi,

On Wed, Sep 24, 2014 at 2:41 PM, Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi Chen-Yu,
>
> On Sun, Sep 21, 2014 at 10:58:07PM +0800, Chen-Yu Tsai wrote:
>> Hi everyone,
>>
>> This patch series adds very basic support for Allwinner's A80 SoC,
>> a big.LITTLE architecture with 4 Cortex-A7s and 4 Cortex-A15s.
>>
>> Development is done on the A80 Optimus Board, the defacto development
>> board for the A80, with the accompanying SDK as a reference.
>>
>> So far I've been unable to get the board to boot from MMC, or
>> using Android fastboot. I'm using Allwinner's FEL mode to load
>> the bootloader and kernel+dtb image over USB. Notes on my attempts
>> can be found here: http://linux-sunxi.org/User:Wens#A80_Optimus
>
> It looks very nice, thanks a lot. You'll find a minor comments inline.
>
> One thing I forgot to ask you about when doing the A23, and that would
> nice to do is to update the documentation we have in
> Documentation/arm/sunxi/README with the A23 and A80 infos you've been
> able to gather.

I'll add the A80 datasheet in v2, and do a separate series for A23, A31,
and A31s docs.


Thanks
ChenYu

Re: [PATCH 0/6] ARM: sunxi: Add basic support for Allwinner A80 SoC

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1507 bytes --]

On Wed, Sep 24, 2014 at 06:40:42PM +0800, Chen-Yu Tsai wrote:
> Hi,
> 
> On Wed, Sep 24, 2014 at 2:41 PM, Maxime Ripard
> <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> > Hi Chen-Yu,
> >
> > On Sun, Sep 21, 2014 at 10:58:07PM +0800, Chen-Yu Tsai wrote:
> >> Hi everyone,
> >>
> >> This patch series adds very basic support for Allwinner's A80 SoC,
> >> a big.LITTLE architecture with 4 Cortex-A7s and 4 Cortex-A15s.
> >>
> >> Development is done on the A80 Optimus Board, the defacto development
> >> board for the A80, with the accompanying SDK as a reference.
> >>
> >> So far I've been unable to get the board to boot from MMC, or
> >> using Android fastboot. I'm using Allwinner's FEL mode to load
> >> the bootloader and kernel+dtb image over USB. Notes on my attempts
> >> can be found here: http://linux-sunxi.org/User:Wens#A80_Optimus
> >
> > It looks very nice, thanks a lot. You'll find a minor comments inline.
> >
> > One thing I forgot to ask you about when doing the A23, and that would
> > nice to do is to update the documentation we have in
> > Documentation/arm/sunxi/README with the A23 and A80 infos you've been
> > able to gather.
> 
> I'll add the A80 datasheet in v2, and do a separate series for A23, A31,
> and A31s docs.

Ah, yes, the A31 and A31s didn't have links to the user manuals...

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]