From: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
To: Russell King <rmk+kernel-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org>
Cc: Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Pawel Moll <pawel.moll-5wv7dgnIgG8@public.gmane.org>,
Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>,
Ian Campbell
<ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg@public.gmane.org>,
Kumar Gala <galak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>,
Sascha Hauer <kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Subject: Re: [PATCH 1/4] ARM: dts: hummingboard: Split HummingBoard DT to support s/dl and d/q
Date: Sun, 26 Oct 2014 08:51:14 +0800 [thread overview]
Message-ID: <20141026005112.GD6973@tiger> (raw)
In-Reply-To: <E1Xhi98-0005pH-D5-eh5Bv4kxaXIANfyc6IWni62ZND6+EDdj@public.gmane.org>
On Fri, Oct 24, 2014 at 05:55:26PM +0100, Russell King wrote:
> From: Rabeeh Khoury <rabeeh-UBr1pzP51AyaMJb+Lgu22Q@public.gmane.org>
> To: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
>
> Signed-off-by: Rabeeh Khoury <rabeeh-UBr1pzP51AyaMJb+Lgu22Q@public.gmane.org>
> Signed-off-by: Russell King <rmk+kernel-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org>
Not sure why these patches are resent, but they are already merged into
v3.18-rc1.
Shawn
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-hummingboard.dts | 203 +---------------------------
> arch/arm/boot/dts/imx6q-hummingboard.dts | 13 ++
> arch/arm/boot/dts/imx6qdl-hummingboard.dtsi | 200 +++++++++++++++++++++++++++
> 4 files changed, 219 insertions(+), 198 deletions(-)
> create mode 100644 arch/arm/boot/dts/imx6q-hummingboard.dts
> create mode 100644 arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b8c5cd3ddeb9..bef8619536ae 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -223,6 +223,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
> imx6q-gw53xx.dtb \
> imx6q-gw5400-a.dtb \
> imx6q-gw54xx.dtb \
> + imx6q-hummingboard.dtb \
> imx6q-nitrogen6x.dtb \
> imx6q-phytec-pbab01.dtb \
> imx6q-rex-pro.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-hummingboard.dts b/arch/arm/boot/dts/imx6dl-hummingboard.dts
> index 71598546087f..44a0e6736bb1 100644
> --- a/arch/arm/boot/dts/imx6dl-hummingboard.dts
> +++ b/arch/arm/boot/dts/imx6dl-hummingboard.dts
> @@ -1,206 +1,13 @@
> /*
> - * Copyright (C) 2013,2014 Russell King
> + * Copyright (C) 2014 Rabeeh Khoury (rabeeh-UBr1pzP51AyaMJb+Lgu22Q@public.gmane.org)
> + * Based on dt work by Russell King
> */
> /dts-v1/;
>
> #include "imx6dl.dtsi"
> -#include "imx6qdl-microsom.dtsi"
> -#include "imx6qdl-microsom-ar8035.dtsi"
> +#include "imx6qdl-hummingboard.dtsi"
>
> / {
> - model = "SolidRun HummingBoard DL/Solo";
> - compatible = "solidrun,hummingboard", "fsl,imx6dl";
> -
> - chosen {
> - stdout-path = &uart1;
> - };
> -
> - ir_recv: ir-receiver {
> - compatible = "gpio-ir-receiver";
> - gpios = <&gpio1 2 1>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_gpio1_2>;
> - };
> -
> - regulators {
> - compatible = "simple-bus";
> -
> - reg_3p3v: 3p3v {
> - compatible = "regulator-fixed";
> - regulator-name = "3P3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - reg_usbh1_vbus: usb-h1-vbus {
> - compatible = "regulator-fixed";
> - enable-active-high;
> - gpio = <&gpio1 0 0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_usbh1_vbus>;
> - regulator-name = "usb_h1_vbus";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - };
> -
> - reg_usbotg_vbus: usb-otg-vbus {
> - compatible = "regulator-fixed";
> - enable-active-high;
> - gpio = <&gpio3 22 0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_usbotg_vbus>;
> - regulator-name = "usb_otg_vbus";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - };
> - };
> -
> - sound-spdif {
> - compatible = "fsl,imx-audio-spdif";
> - model = "On-board SPDIF";
> - /* IMX6 doesn't implement this yet */
> - spdif-controller = <&spdif>;
> - spdif-out;
> - };
> -};
> -
> -&can1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_flexcan1>;
> - status = "okay";
> -};
> -
> -&hdmi {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_hdmi>;
> - ddc-i2c-bus = <&i2c2>;
> - status = "okay";
> -};
> -
> -&i2c1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_i2c1>;
> -
> - /*
> - * Not fitted on Carrier-1 board... yet
> - status = "okay";
> -
> - rtc: pcf8523@68 {
> - compatible = "nxp,pcf8523";
> - reg = <0x68>;
> - };
> - */
> -};
> -
> -&i2c2 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_i2c2>;
> - status = "okay";
> -};
> -
> -&iomuxc {
> - hummingboard {
> - pinctrl_hummingboard_flexcan1: hummingboard-flexcan1 {
> - fsl,pins = <
> - MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
> - MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
> - >;
> - };
> -
> - pinctrl_hummingboard_gpio1_2: hummingboard-gpio1_2 {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000
> - >;
> - };
> -
> - pinctrl_hummingboard_hdmi: hummingboard-hdmi {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
> - >;
> - };
> -
> - pinctrl_hummingboard_i2c1: hummingboard-i2c1 {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> - MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> - >;
> - };
> -
> - pinctrl_hummingboard_i2c2: hummingboard-i2c2 {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> - MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> - >;
> - };
> -
> - pinctrl_hummingboard_spdif: hummingboard-spdif {
> - fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
> - };
> -
> - pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
> - fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
> - };
> -
> - pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-id {
> - /*
> - * Similar to pinctrl_usbotg_2, but we want it
> - * pulled down for a fixed host connection.
> - */
> - fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
> - };
> -
> - pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
> - fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
> - };
> -
> - pinctrl_hummingboard_usdhc2_aux: hummingboard-usdhc2-aux {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
> - >;
> - };
> -
> - pinctrl_hummingboard_usdhc2: hummingboard-usdhc2 {
> - fsl,pins = <
> - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
> - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
> - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
> - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
> - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
> - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
> - >;
> - };
> - };
> -};
> -
> -&spdif {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_spdif>;
> - status = "okay";
> -};
> -
> -&usbh1 {
> - disable-over-current;
> - vbus-supply = <®_usbh1_vbus>;
> - status = "okay";
> -};
> -
> -&usbotg {
> - disable-over-current;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
> - vbus-supply = <®_usbotg_vbus>;
> - status = "okay";
> -};
> -
> -&usdhc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <
> - &pinctrl_hummingboard_usdhc2_aux
> - &pinctrl_hummingboard_usdhc2
> - >;
> - vmmc-supply = <®_3p3v>;
> - cd-gpios = <&gpio1 4 0>;
> - status = "okay";
> + model = "SolidRun HummingBoard Solo/DualLite";
> + compatible = "solidrun,hummingboard/dl", "fsl,imx6dl";
> };
> diff --git a/arch/arm/boot/dts/imx6q-hummingboard.dts b/arch/arm/boot/dts/imx6q-hummingboard.dts
> new file mode 100644
> index 000000000000..0a3574105165
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-hummingboard.dts
> @@ -0,0 +1,13 @@
> +/*
> + * Copyright (C) 2014 Rabeeh Khoury (rabeeh-UBr1pzP51AyaMJb+Lgu22Q@public.gmane.org)
> + * Based on dt work by Russell King
> + */
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-hummingboard.dtsi"
> +
> +/ {
> + model = "SolidRun HummingBoard Dual/Quad";
> + compatible = "solidrun,hummingboard/q", "fsl,imx6q";
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
> new file mode 100644
> index 000000000000..bf38072a2779
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
> @@ -0,0 +1,200 @@
> +/*
> + * Copyright (C) 2013,2014 Russell King
> + */
> +#include "imx6qdl-microsom.dtsi"
> +#include "imx6qdl-microsom-ar8035.dtsi"
> +
> +/ {
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + ir_recv: ir-receiver {
> + compatible = "gpio-ir-receiver";
> + gpios = <&gpio1 2 1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_gpio1_2>;
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> +
> + reg_3p3v: 3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_usbh1_vbus: usb-h1-vbus {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 0 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_usbh1_vbus>;
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + reg_usbotg_vbus: usb-otg-vbus {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio3 22 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_usbotg_vbus>;
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> + };
> +
> + sound-spdif {
> + compatible = "fsl,imx-audio-spdif";
> + model = "On-board SPDIF";
> + /* IMX6 doesn't implement this yet */
> + spdif-controller = <&spdif>;
> + spdif-out;
> + };
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_flexcan1>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_hdmi>;
> + ddc-i2c-bus = <&i2c2>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_i2c1>;
> +
> + /*
> + * Not fitted on Carrier-1 board... yet
> + status = "okay";
> +
> + rtc: pcf8523@68 {
> + compatible = "nxp,pcf8523";
> + reg = <0x68>;
> + };
> + */
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_i2c2>;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + hummingboard {
> + pinctrl_hummingboard_flexcan1: hummingboard-flexcan1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
> + MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
> + >;
> + };
> +
> + pinctrl_hummingboard_gpio1_2: hummingboard-gpio1_2 {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000
> + >;
> + };
> +
> + pinctrl_hummingboard_hdmi: hummingboard-hdmi {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
> + >;
> + };
> +
> + pinctrl_hummingboard_i2c1: hummingboard-i2c1 {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_hummingboard_i2c2: hummingboard-i2c2 {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_hummingboard_spdif: hummingboard-spdif {
> + fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
> + };
> +
> + pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
> + fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
> + };
> +
> + pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-id {
> + /*
> + * Similar to pinctrl_usbotg_2, but we want it
> + * pulled down for a fixed host connection.
> + */
> + fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
> + };
> +
> + pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
> + fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
> + };
> +
> + pinctrl_hummingboard_usdhc2_aux: hummingboard-usdhc2-aux {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
> + >;
> + };
> +
> + pinctrl_hummingboard_usdhc2: hummingboard-usdhc2 {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
> + >;
> + };
> + };
> +};
> +
> +&spdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_spdif>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + disable-over-current;
> + vbus-supply = <®_usbh1_vbus>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + disable-over-current;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
> + vbus-supply = <®_usbotg_vbus>;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <
> + &pinctrl_hummingboard_usdhc2_aux
> + &pinctrl_hummingboard_usdhc2
> + >;
> + vmmc-supply = <®_3p3v>;
> + cd-gpios = <&gpio1 4 0>;
> + status = "okay";
> +};
> --
> 1.8.3.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
prev parent reply other threads:[~2014-10-26 0:51 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-24 16:55 [PATCH 1/4] ARM: dts: hummingboard: Split HummingBoard DT to support s/dl and d/q Russell King
[not found] ` <E1Xhi98-0005pH-D5-eh5Bv4kxaXIANfyc6IWni62ZND6+EDdj@public.gmane.org>
2014-10-26 0:51 ` Shawn Guo [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20141026005112.GD6973@tiger \
--to=shawn.guo-qsej5fyqhm4dnm+yrofe0a@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=galak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org \
--cc=ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg@public.gmane.org \
--cc=kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=pawel.moll-5wv7dgnIgG8@public.gmane.org \
--cc=rmk+kernel-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).