* [PATCH 0/3] ARM: dts: vf610: USB/GPIO fixes
@ 2014-11-04 13:07 Stefan Agner
2014-11-04 13:07 ` [PATCH 1/3] ARM: dts: vf610: use new GPIO support Stefan Agner
` (3 more replies)
0 siblings, 4 replies; 8+ messages in thread
From: Stefan Agner @ 2014-11-04 13:07 UTC (permalink / raw)
To: shawn.guo-QSEj5FYQhm4dnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ
Cc: linus.walleij-QSEj5FYQhm4dnm+yROfE0A,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, stefan-XLVq0VzYD2Y
Hi Shawn,
This patchset collects some vf610 device tree fixes. The first patch
was part of the "vf610: Add GPIO support" patchset. GPIO support is
merged by know, so I rebased that on top of your for-next branch.
The second patch is a USB fix I uncovered while testing the 3rd patch,
which adds regulators, mainly for proper USB VBUS support, as we have
them on our carrier boards.
Stefan Agner (3):
ARM: dts: vf610: use new GPIO support
ARM: dts: vf610: enable USB misc/phy nodes where necessary
ARM: dts: vf-colibri: add USB regulators
arch/arm/boot/dts/vf-colibri-eval-v3.dtsi | 45 ++++++++++++++++++++++++++++++-
arch/arm/boot/dts/vf-colibri.dtsi | 37 +++++++++++++++++++++++++
arch/arm/boot/dts/vf610-twr.dts | 9 +++++++
arch/arm/boot/dts/vfxxx.dtsi | 1 +
4 files changed, 91 insertions(+), 1 deletion(-)
--
2.1.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH 1/3] ARM: dts: vf610: use new GPIO support 2014-11-04 13:07 [PATCH 0/3] ARM: dts: vf610: USB/GPIO fixes Stefan Agner @ 2014-11-04 13:07 ` Stefan Agner 2014-11-04 13:07 ` [PATCH 2/3] ARM: dts: vf610: enable USB misc/phy nodes where necessary Stefan Agner ` (2 subsequent siblings) 3 siblings, 0 replies; 8+ messages in thread From: Stefan Agner @ 2014-11-04 13:07 UTC (permalink / raw) To: shawn.guo, kernel Cc: linus.walleij, devicetree, linux-arm-kernel, linux-kernel, stefan Use GPIO support by adding SD card detection configuration and GPIO pinmux for Colibri's standard GPIO pins. Attach the GPIO pins to the iomuxc node to get the GPIO pin settings applied. Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Linus Walleij <linus.walleij@linaro.org> --- arch/arm/boot/dts/vf-colibri.dtsi | 9 +++++++++ arch/arm/boot/dts/vf610-twr.dts | 1 + arch/arm/boot/dts/vfxxx.dtsi | 1 + 3 files changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi index ab40367..ab9616d7 100644 --- a/arch/arm/boot/dts/vf-colibri.dtsi +++ b/arch/arm/boot/dts/vf-colibri.dtsi @@ -31,6 +31,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_esdhc1>; bus-width = <4>; + cd-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; }; &fec1 { @@ -76,6 +77,14 @@ &iomuxc { vf610-colibri { + pinctrl_gpio_ext: gpio_ext { + fsl,pins = < + VF610_PAD_PTD10__GPIO_89 0x22ed /* EXT_IO_0 */ + VF610_PAD_PTD9__GPIO_88 0x22ed /* EXT_IO_1 */ + VF610_PAD_PTD26__GPIO_68 0x22ed /* EXT_IO_2 */ + >; + }; + pinctrl_esdhc1: esdhc1grp { fsl,pins = < VF610_PAD_PTA24__ESDHC1_CLK 0x31ef diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-twr.dts index ebc906b..793a376 100644 --- a/arch/arm/boot/dts/vf610-twr.dts +++ b/arch/arm/boot/dts/vf610-twr.dts @@ -123,6 +123,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_esdhc1>; bus-width = <4>; + cd-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>; status = "okay"; }; diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/vfxxx.dtsi index 4e70833..505969a 100644 --- a/arch/arm/boot/dts/vfxxx.dtsi +++ b/arch/arm/boot/dts/vfxxx.dtsi @@ -10,6 +10,7 @@ #include "vf610-pinfunc.h" #include <dt-bindings/clock/vf610-clock.h> #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> / { aliases { -- 2.1.3 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/3] ARM: dts: vf610: enable USB misc/phy nodes where necessary 2014-11-04 13:07 [PATCH 0/3] ARM: dts: vf610: USB/GPIO fixes Stefan Agner 2014-11-04 13:07 ` [PATCH 1/3] ARM: dts: vf610: use new GPIO support Stefan Agner @ 2014-11-04 13:07 ` Stefan Agner 2014-11-04 13:07 ` [PATCH 3/3] ARM: dts: vf-colibri: add USB regulators Stefan Agner [not found] ` <1415106430-6271-1-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org> 3 siblings, 0 replies; 8+ messages in thread From: Stefan Agner @ 2014-11-04 13:07 UTC (permalink / raw) To: shawn.guo, kernel Cc: linus.walleij, devicetree, linux-arm-kernel, linux-kernel, stefan Since restructuring of the device tree files, the USB misc/phy nodes are disabled by default. Hence we need to enable those explicitly when USB is used. Signed-off-by: Stefan Agner <stefan@agner.ch> --- arch/arm/boot/dts/vf-colibri.dtsi | 16 ++++++++++++++++ arch/arm/boot/dts/vf610-twr.dts | 8 ++++++++ 2 files changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi index ab9616d7..2371760 100644 --- a/arch/arm/boot/dts/vf-colibri.dtsi +++ b/arch/arm/boot/dts/vf-colibri.dtsi @@ -75,6 +75,22 @@ status = "okay"; }; +&usbmisc0 { + status = "okay"; +}; + +&usbmisc1 { + status = "okay"; +}; + +&usbphy0 { + status = "okay"; +}; + +&usbphy1 { + status = "okay"; +}; + &iomuxc { vf610-colibri { pinctrl_gpio_ext: gpio_ext { diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-twr.dts index 793a376..a0f7621 100644 --- a/arch/arm/boot/dts/vf610-twr.dts +++ b/arch/arm/boot/dts/vf610-twr.dts @@ -294,6 +294,14 @@ status = "okay"; }; +&usbmisc0 { + status = "okay"; +}; + +&usbmisc1 { + status = "okay"; +}; + &usbphy0 { status = "okay"; }; -- 2.1.3 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 3/3] ARM: dts: vf-colibri: add USB regulators 2014-11-04 13:07 [PATCH 0/3] ARM: dts: vf610: USB/GPIO fixes Stefan Agner 2014-11-04 13:07 ` [PATCH 1/3] ARM: dts: vf610: use new GPIO support Stefan Agner 2014-11-04 13:07 ` [PATCH 2/3] ARM: dts: vf610: enable USB misc/phy nodes where necessary Stefan Agner @ 2014-11-04 13:07 ` Stefan Agner [not found] ` <1415106430-6271-4-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org> [not found] ` <1415106430-6271-1-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org> 3 siblings, 1 reply; 8+ messages in thread From: Stefan Agner @ 2014-11-04 13:07 UTC (permalink / raw) To: shawn.guo, kernel Cc: linus.walleij, devicetree, linux-arm-kernel, linux-kernel, stefan Add structure of USB supply logic. Especially, the USB hosts power enable regulator is needed to control VBUS supply. Signed-off-by: Stefan Agner <stefan@agner.ch> --- arch/arm/boot/dts/vf-colibri-eval-v3.dtsi | 45 ++++++++++++++++++++++++++++++- arch/arm/boot/dts/vf-colibri.dtsi | 12 +++++++++ 2 files changed, 56 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi index 80e8fbc..eb4ca50 100644 --- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi +++ b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi @@ -11,6 +11,41 @@ chosen { bootargs = "console=ttyLP0,115200"; }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + sys_5v0_reg: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + usbc_vbus_reg: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usbc_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&sys_5v0_reg>; + }; + + /* USBH_PEN */ + usbh_vbus_reg: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "usbh_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 19 GPIO_ACTIVE_LOW>; + vin-supply = <&sys_5v0_reg>; + }; + }; }; &bl { @@ -51,4 +86,12 @@ &uart2 { status = "okay"; -}; \ No newline at end of file +}; + +&usbdev0 { + vbus-supply = <&usbc_vbus_reg>; +}; + +&usbh1 { + vbus-supply = <&usbh_vbus_reg>; +}; diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi index 2371760..79ccfe2 100644 --- a/arch/arm/boot/dts/vf-colibri.dtsi +++ b/arch/arm/boot/dts/vf-colibri.dtsi @@ -163,5 +163,17 @@ VF610_PAD_PTD3__UART2_CTS 0x21a1 >; }; + + pinctrl_usbh1_ext: gpio_usb_vbus { + fsl,pins = < + VF610_PAD_PTD4__GPIO_83 0x22ed + >; + }; + + pinctrl_usbdev0_ext: gpio_usb_cdet { + fsl,pins = < + VF610_PAD_PTC29__GPIO_102 0x22ed + >; + }; }; }; -- 2.1.3 ^ permalink raw reply related [flat|nested] 8+ messages in thread
[parent not found: <1415106430-6271-4-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org>]
* Re: [PATCH 3/3] ARM: dts: vf-colibri: add USB regulators [not found] ` <1415106430-6271-4-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org> @ 2014-11-11 14:12 ` Shawn Guo 2014-11-12 15:51 ` Stefan Agner 0 siblings, 1 reply; 8+ messages in thread From: Shawn Guo @ 2014-11-11 14:12 UTC (permalink / raw) To: Stefan Agner Cc: kernel-bIcnvbaLZ9MEGnE8C9+IrQ, linus.walleij-QSEj5FYQhm4dnm+yROfE0A, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA On Tue, Nov 04, 2014 at 02:07:10PM +0100, Stefan Agner wrote: > Add structure of USB supply logic. Especially, the USB hosts power > enable regulator is needed to control VBUS supply. > > Signed-off-by: Stefan Agner <stefan-XLVq0VzYD2Y@public.gmane.org> > --- > arch/arm/boot/dts/vf-colibri-eval-v3.dtsi | 45 ++++++++++++++++++++++++++++++- > arch/arm/boot/dts/vf-colibri.dtsi | 12 +++++++++ > 2 files changed, 56 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi > index 80e8fbc..eb4ca50 100644 > --- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi > +++ b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi > @@ -11,6 +11,41 @@ > chosen { > bootargs = "console=ttyLP0,115200"; > }; > + > + regulators { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + sys_5v0_reg: regulator@1 { > + compatible = "regulator-fixed"; > + reg = <1>; The numbering generally starts from 0 instead of 1. > + regulator-name = "5v0"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + usbc_vbus_reg: regulator@2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "usbc_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&sys_5v0_reg>; > + }; > + > + /* USBH_PEN */ > + usbh_vbus_reg: regulator@3 { > + compatible = "regulator-fixed"; > + reg = <3>; > + regulator-name = "usbh_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio3 19 GPIO_ACTIVE_LOW>; > + vin-supply = <&sys_5v0_reg>; > + }; > + }; > }; > > &bl { > @@ -51,4 +86,12 @@ > > &uart2 { > status = "okay"; > -}; > \ No newline at end of file > +}; > + > +&usbdev0 { > + vbus-supply = <&usbc_vbus_reg>; > +}; > + > +&usbh1 { > + vbus-supply = <&usbh_vbus_reg>; > +}; > diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi > index 2371760..79ccfe2 100644 > --- a/arch/arm/boot/dts/vf-colibri.dtsi > +++ b/arch/arm/boot/dts/vf-colibri.dtsi > @@ -163,5 +163,17 @@ > VF610_PAD_PTD3__UART2_CTS 0x21a1 > >; > }; > + > + pinctrl_usbh1_ext: gpio_usb_vbus { > + fsl,pins = < > + VF610_PAD_PTD4__GPIO_83 0x22ed We used to know the GPIO usage by looking for the phandle reference to the node. But it doesn't work for VF610 case now. I guess this is for usbh_vbus_reg usage? It would be nice to have a comment telling the usage of the GPIO. > + >; > + }; > + > + pinctrl_usbdev0_ext: gpio_usb_cdet { > + fsl,pins = < > + VF610_PAD_PTC29__GPIO_102 0x22ed How is this one used? Shawn > + >; > + }; > }; > }; > -- > 2.1.3 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 3/3] ARM: dts: vf-colibri: add USB regulators 2014-11-11 14:12 ` Shawn Guo @ 2014-11-12 15:51 ` Stefan Agner [not found] ` <0bb62bdfc866f75977d01070d228ed4c-XLVq0VzYD2Y@public.gmane.org> 0 siblings, 1 reply; 8+ messages in thread From: Stefan Agner @ 2014-11-12 15:51 UTC (permalink / raw) To: Shawn Guo Cc: kernel, linus.walleij, devicetree, linux-arm-kernel, linux-kernel On 2014-11-11 15:12, Shawn Guo wrote: > On Tue, Nov 04, 2014 at 02:07:10PM +0100, Stefan Agner wrote: >> Add structure of USB supply logic. Especially, the USB hosts power >> enable regulator is needed to control VBUS supply. >> >> Signed-off-by: Stefan Agner <stefan@agner.ch> >> --- >> arch/arm/boot/dts/vf-colibri-eval-v3.dtsi | 45 ++++++++++++++++++++++++++++++- >> arch/arm/boot/dts/vf-colibri.dtsi | 12 +++++++++ >> 2 files changed, 56 insertions(+), 1 deletion(-) >> >> diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi >> index 80e8fbc..eb4ca50 100644 >> --- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi >> +++ b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi >> @@ -11,6 +11,41 @@ >> chosen { >> bootargs = "console=ttyLP0,115200"; >> }; >> + >> + regulators { >> + compatible = "simple-bus"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + sys_5v0_reg: regulator@1 { >> + compatible = "regulator-fixed"; >> + reg = <1>; > > The numbering generally starts from 0 instead of 1. > >> + regulator-name = "5v0"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + regulator-always-on; >> + }; >> + >> + usbc_vbus_reg: regulator@2 { >> + compatible = "regulator-fixed"; >> + reg = <2>; >> + regulator-name = "usbc_vbus"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + vin-supply = <&sys_5v0_reg>; >> + }; >> + >> + /* USBH_PEN */ >> + usbh_vbus_reg: regulator@3 { >> + compatible = "regulator-fixed"; >> + reg = <3>; >> + regulator-name = "usbh_vbus"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + gpio = <&gpio3 19 GPIO_ACTIVE_LOW>; >> + vin-supply = <&sys_5v0_reg>; >> + }; >> + }; >> }; >> >> &bl { >> @@ -51,4 +86,12 @@ >> >> &uart2 { >> status = "okay"; >> -}; >> \ No newline at end of file >> +}; >> + >> +&usbdev0 { >> + vbus-supply = <&usbc_vbus_reg>; >> +}; >> + >> +&usbh1 { >> + vbus-supply = <&usbh_vbus_reg>; >> +}; >> diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi >> index 2371760..79ccfe2 100644 >> --- a/arch/arm/boot/dts/vf-colibri.dtsi >> +++ b/arch/arm/boot/dts/vf-colibri.dtsi >> @@ -163,5 +163,17 @@ >> VF610_PAD_PTD3__UART2_CTS 0x21a1 >> >; >> }; >> + >> + pinctrl_usbh1_ext: gpio_usb_vbus { >> + fsl,pins = < >> + VF610_PAD_PTD4__GPIO_83 0x22ed > > We used to know the GPIO usage by looking for the phandle reference to > the node. But it doesn't work for VF610 case now. > > I guess this is for usbh_vbus_reg usage? It would be nice to have a > comment telling the usage of the GPIO. Yeah its true, its assign is not required for Vybird. However, we could assign them anyway, it would even enforce correct pin setup from Startup... This would then make a comment superfluous. What do you think? > >> + >; >> + }; >> + >> + pinctrl_usbdev0_ext: gpio_usb_cdet { >> + fsl,pins = < >> + VF610_PAD_PTC29__GPIO_102 0x22ed > > How is this one used? This is not yet used. It is more or less the OTG-ID pin, but on 3.3V level. We use that on the Colibri standard to switch between Host/Device mode, however a driver which uses that GPIO is still outstanding. I can also leave that away for now, if you prefer.... -- Stefan > > Shawn > >> + >; >> + }; >> }; >> }; >> -- >> 2.1.3 >> ^ permalink raw reply [flat|nested] 8+ messages in thread
[parent not found: <0bb62bdfc866f75977d01070d228ed4c-XLVq0VzYD2Y@public.gmane.org>]
* Re: [PATCH 3/3] ARM: dts: vf-colibri: add USB regulators [not found] ` <0bb62bdfc866f75977d01070d228ed4c-XLVq0VzYD2Y@public.gmane.org> @ 2014-11-13 1:23 ` Shawn Guo 0 siblings, 0 replies; 8+ messages in thread From: Shawn Guo @ 2014-11-13 1:23 UTC (permalink / raw) To: Stefan Agner Cc: kernel-bIcnvbaLZ9MEGnE8C9+IrQ, linus.walleij-QSEj5FYQhm4dnm+yROfE0A, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA On Wed, Nov 12, 2014 at 04:51:16PM +0100, Stefan Agner wrote: > >> diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi > >> index 2371760..79ccfe2 100644 > >> --- a/arch/arm/boot/dts/vf-colibri.dtsi > >> +++ b/arch/arm/boot/dts/vf-colibri.dtsi > >> @@ -163,5 +163,17 @@ > >> VF610_PAD_PTD3__UART2_CTS 0x21a1 > >> >; > >> }; > >> + > >> + pinctrl_usbh1_ext: gpio_usb_vbus { > >> + fsl,pins = < > >> + VF610_PAD_PTD4__GPIO_83 0x22ed > > > > We used to know the GPIO usage by looking for the phandle reference to > > the node. But it doesn't work for VF610 case now. > > > > I guess this is for usbh_vbus_reg usage? It would be nice to have a > > comment telling the usage of the GPIO. > > Yeah its true, its assign is not required for Vybird. However, we could > assign them anyway, it would even enforce correct pin setup from > Startup... This would then make a comment superfluous. What do you > think? I agree with the approach of assigning the phandle anyway. > > > > > >> + >; > >> + }; > >> + > >> + pinctrl_usbdev0_ext: gpio_usb_cdet { > >> + fsl,pins = < > >> + VF610_PAD_PTC29__GPIO_102 0x22ed > > > > How is this one used? > > This is not yet used. It is more or less the OTG-ID pin, but on 3.3V > level. We use that on the Colibri standard to switch between Host/Device > mode, however a driver which uses that GPIO is still outstanding. I can > also leave that away for now, if you prefer.... Then let's add it when it's actually required. Shawn -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 8+ messages in thread
[parent not found: <1415106430-6271-1-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org>]
* Re: [PATCH 0/3] ARM: dts: vf610: USB/GPIO fixes [not found] ` <1415106430-6271-1-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org> @ 2014-11-11 14:14 ` Shawn Guo 0 siblings, 0 replies; 8+ messages in thread From: Shawn Guo @ 2014-11-11 14:14 UTC (permalink / raw) To: Stefan Agner Cc: kernel-bIcnvbaLZ9MEGnE8C9+IrQ, linus.walleij-QSEj5FYQhm4dnm+yROfE0A, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel-u79uwXL29TY76Z2rM5mHXA On Tue, Nov 04, 2014 at 02:07:07PM +0100, Stefan Agner wrote: > Hi Shawn, > > This patchset collects some vf610 device tree fixes. The first patch > was part of the "vf610: Add GPIO support" patchset. GPIO support is > merged by know, so I rebased that on top of your for-next branch. > > The second patch is a USB fix I uncovered while testing the 3rd patch, > which adds regulators, mainly for proper USB VBUS support, as we have > them on our carrier boards. > > Stefan Agner (3): > ARM: dts: vf610: use new GPIO support > ARM: dts: vf610: enable USB misc/phy nodes where necessary Applied the first two, thanks. Shawn > ARM: dts: vf-colibri: add USB regulators > > arch/arm/boot/dts/vf-colibri-eval-v3.dtsi | 45 ++++++++++++++++++++++++++++++- > arch/arm/boot/dts/vf-colibri.dtsi | 37 +++++++++++++++++++++++++ > arch/arm/boot/dts/vf610-twr.dts | 9 +++++++ > arch/arm/boot/dts/vfxxx.dtsi | 1 + > 4 files changed, 91 insertions(+), 1 deletion(-) > > -- > 2.1.3 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2014-11-13 1:23 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-11-04 13:07 [PATCH 0/3] ARM: dts: vf610: USB/GPIO fixes Stefan Agner
2014-11-04 13:07 ` [PATCH 1/3] ARM: dts: vf610: use new GPIO support Stefan Agner
2014-11-04 13:07 ` [PATCH 2/3] ARM: dts: vf610: enable USB misc/phy nodes where necessary Stefan Agner
2014-11-04 13:07 ` [PATCH 3/3] ARM: dts: vf-colibri: add USB regulators Stefan Agner
[not found] ` <1415106430-6271-4-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org>
2014-11-11 14:12 ` Shawn Guo
2014-11-12 15:51 ` Stefan Agner
[not found] ` <0bb62bdfc866f75977d01070d228ed4c-XLVq0VzYD2Y@public.gmane.org>
2014-11-13 1:23 ` Shawn Guo
[not found] ` <1415106430-6271-1-git-send-email-stefan-XLVq0VzYD2Y@public.gmane.org>
2014-11-11 14:14 ` [PATCH 0/3] ARM: dts: vf610: USB/GPIO fixes Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).