From: Pavel Machek <pavel@ucw.cz>
To: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>,
linux-leds@vger.kernel.org, linux-media@vger.kernel.org,
linux-kernel@vger.kernel.org, kyungmin.park@samsung.com,
b.zolnierkie@samsung.com, cooloney@gmail.com, rpurdie@rpsys.net,
s.nawrocki@samsung.com, robh+dt@kernel.org, pawel.moll@arm.com,
mark.rutland@arm.com, ijc+devicetree@hellion.org.uk,
galak@codeaurora.org, Andrzej Hajda <a.hajda@samsung.com>,
Lee Jones <lee.jones@linaro.org>,
Chanwoo Choi <cw00.choi@samsung.com>,
devicetree@vger.kernel.org
Subject: Re: [PATCH/RFC v9 06/19] DT: Add documentation for the mfd Maxim max77693
Date: Thu, 4 Dec 2014 17:12:02 +0100 [thread overview]
Message-ID: <20141204161201.GB29080@amd> (raw)
In-Reply-To: <54804840.4030202@samsung.com>
Hi!
> >>+- maxim,boost-mode :
> >>+ In boost mode the device can produce up to 1.2A of total current
> >>+ on both outputs. The maximum current on each output is reduced
> >>+ to 625mA then. If there are two child led nodes defined then boost
> >>+ is enabled by default.
> >>+ Possible values:
> >>+ MAX77693_LED_BOOST_OFF - no boost,
> >>+ MAX77693_LED_BOOST_ADAPTIVE - adaptive mode,
> >>+ MAX77693_LED_BOOST_FIXED - fixed mode.
> >>+- maxim,boost-vout : Output voltage of the boost module in millivolts.
> >>+- maxim,vsys-min : Low input voltage level in millivolts. Flash is not fired
> >>+ if chip estimates that system voltage could drop below this level due
> >>+ to flash power consumption.
> >>+
> >>+Required properties of the LED child node:
> >>+- label : see Documentation/devicetree/bindings/leds/common.txt
> >>+- maxim,fled_id : Identifier of the fled output the led is connected to;
> >
> >I'm pretty sure this will be needed for about every chip that can drive
> >multiple LEDs. Shouldn't it be documented in the generic documentation?
>
> OK.
Well... "fled_id" is not exactly suitable name. On other busses, it
would be "reg = <1>"?
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
next prev parent reply other threads:[~2014-12-04 16:12 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <1417622814-10845-1-git-send-email-j.anaszewski@samsung.com>
2014-12-03 16:06 ` [PATCH/RFC v9 06/19] DT: Add documentation for the mfd Maxim max77693 Jacek Anaszewski
2014-12-04 10:07 ` Sakari Ailus
2014-12-04 11:40 ` Jacek Anaszewski
2014-12-04 16:12 ` Pavel Machek [this message]
2014-12-08 10:29 ` Jacek Anaszewski
2014-12-10 12:20 ` Sylwester Nawrocki
2014-12-10 12:41 ` Jacek Anaszewski
2014-12-09 14:09 ` Sakari Ailus
2014-12-09 14:13 ` Jacek Anaszewski
2014-12-10 10:02 ` Jacek Anaszewski
2014-12-10 10:50 ` Sakari Ailus
2014-12-10 10:59 ` Sylwester Nawrocki
2014-12-03 16:06 ` [PATCH/RFC v9 09/19] of: Add Skyworks Solutions, Inc. vendor prefix Jacek Anaszewski
2014-12-03 16:06 ` [PATCH/RFC v9 10/19] DT: Add documentation for the Skyworks AAT1290 Jacek Anaszewski
2014-12-03 16:06 ` [PATCH/RFC v9 17/19] DT: Add documentation for exynos4-is 'flashes' property Jacek Anaszewski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20141204161201.GB29080@amd \
--to=pavel@ucw.cz \
--cc=a.hajda@samsung.com \
--cc=b.zolnierkie@samsung.com \
--cc=cooloney@gmail.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=j.anaszewski@samsung.com \
--cc=kyungmin.park@samsung.com \
--cc=lee.jones@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=rpurdie@rpsys.net \
--cc=s.nawrocki@samsung.com \
--cc=sakari.ailus@iki.fi \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).