[PATCH 2/2] ARM: dts: kirkwood: add dts support for Seagate BlackArmor NAS220

[Evgeni Dobrev <evgeni@studio-punkt.com>]

This patch adds support for Seagate BlackArmor NAS220.

The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has 32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two USB 2.0 ports, two buttons and three LEDs. There is a serial port available on the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND).

The only functionality still not implemented is the bi-color led on the front panel (status). Pins mpp22 and mpp23 control this led. Setting mpp22 to high and mpp23 to low results in orange color. Setting mpp22 to low and mpp23 to high results in blue color.

The third led is wired to show the SATA activity on the two drives.

Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
---
 arch/arm/boot/dts/Makefile            |    1 +
 arch/arm/boot/dts/kirkwood-nas220.dts |  182 +++++++++++++++++++++++++++++++++
 2 files changed, 183 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-nas220.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 38c89ca..8b9ad1d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -132,6 +132,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
 	kirkwood-lsxhl.dtb \
 	kirkwood-mplcec4.dtb \
 	kirkwood-mv88f6281gtw-ge.dtb \
+	kirkwood-nas220.dtb \
 	kirkwood-net2big.dtb \
 	kirkwood-net5big.dtb \
 	kirkwood-netgear_readynas_duo_v2.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-nas220.dts b/arch/arm/boot/dts/kirkwood-nas220.dts
new file mode 100644
index 0000000..1de2ac3
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-nas220.dts
@@ -0,0 +1,182 @@
+/*
+ * Device Tree file for Seagate BlackArmor NAS220
+ *
+ * Copyright (C) 2014 Evgeni Dobrev <evgeni@studio-punkt.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+	model = "Seagate NAS 220";
+	compatible = "seagate,nas220", "marvell,kirkwood-88f6192", "marvell,kirkwood";
+
+	memory { /* 128 MB */
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+        chosen {
+                bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+        };
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-0 = < &pmx_uart0
+				&pmx_button_reset
+				&pmx_button_power
+				>;
+			pinctrl-names = "default";
+
+                        pmx_act_sata0: pmx-act-sata0 {
+                                marvell,pins = "mpp15";
+                                marvell,function = "sata0";
+                        };
+                        pmx_act_sata1: pmx-act-sata1 {
+                                marvell,pins = "mpp16";
+                                marvell,function = "sata1";
+                        };
+                        pmx_power_sata0: pmx-power-sata0 {
+                                marvell,pins = "mpp24";
+                                marvell,function = "gpio";
+                        };
+                        pmx_power_sata1: pmx-power-sata1 {
+                                marvell,pins = "mpp28";
+                                marvell,function = "gpio";
+                        };
+                        pmx_button_reset: pmx-button-reset {
+                                marvell,pins = "mpp29";
+                                marvell,function = "gpio";
+                        };
+                        pmx_button_power: pmx-button-power {
+                                marvell,pins = "mpp26";
+                                marvell,function = "gpio";
+                        };
+		};
+
+		serial@12000 {
+			status = "okay";
+		};
+
+                sata@80000 {
+                        nr-ports = <2>;
+                        status = "okay";
+                };
+
+		i2c@11000 {
+			status = "okay";
+			adt7476: adt7476a@2e {
+				compatible = "adi,adt7476";
+				reg = <0x2e>;
+			};
+		};
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button@1{
+			label = "Reset push button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+		button@2{
+			label = "Power push button";
+			linux,code = <KEY_SLEEP>;
+			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		blue-power {
+			label = "nas220:blue:power";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+        regulators {
+                compatible = "simple-bus";
+                #address-cells = <1>;
+                #size-cells = <0>;
+                pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>;
+                pinctrl-names = "default";
+
+                sata0_power: regulator@1 {
+                        compatible = "regulator-fixed";
+                        reg = <1>;
+                        regulator-name = "SATA0 Power";
+                        regulator-min-microvolt = <5000000>;
+                        regulator-max-microvolt = <5000000>;
+                        enable-active-high;
+                        regulator-always-on;
+                        regulator-boot-on;
+                        gpio = <&gpio0 24 0>;
+                };
+
+                sata1_power: regulator@2 {
+                        compatible = "regulator-fixed";
+                        reg = <2>;
+                        regulator-name = "SATA1 Power";
+                        regulator-min-microvolt = <5000000>;
+                        regulator-max-microvolt = <5000000>;
+                        enable-active-high;
+                        regulator-always-on;
+                        regulator-boot-on;
+                        gpio = <&gpio0 28 0>;
+                };
+        };
+};
+
+&nand {
+	status = "okay";
+	partition@0 {
+		label = "uboot";
+		reg = <0x0 0xa0000>;
+		read-only;
+	};
+
+	partition@a0000 {
+		label = "env";
+		reg = <0xa0000 0x010000>;
+	};
+
+	partition@c0000 {
+		label = "uimage";
+		reg = <0xc0000 0x500000>;
+	};
+
+	partition@5c0000 {
+		label = "rootfs";
+		reg = <0x5c0000 0x1a40000>;
+	};
+};
+
+&mdio {
+        status = "okay";
+        ethphy0: ethernet-phy@8 {
+                reg = <8>;
+        };
+};
+
+&eth0 {
+        status = "okay";
+        ethernet0-port@0 {
+                phy-handle = <&ethphy0>;
+        };
+};
+
-- 
1.7.10.4