* [PATCH] arm: dts: imx6sx: add i.mx6sx sabreauto board support
@ 2014-12-08 7:05 Anson Huang
[not found] ` <1418022354-21988-1-git-send-email-b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
0 siblings, 1 reply; 2+ messages in thread
From: Anson Huang @ 2014-12-08 7:05 UTC (permalink / raw)
To: shawn.guo-QSEj5FYQhm4dnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA
Add basic i.MX6SoloX Sabre Auto board support, currently
only debug UART and uSDHC are supported on this board.
Signed-off-by: Anson Huang <b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6sx-sabreauto.dts | 135 ++++++++++++++++++++++++++++++++
2 files changed, 136 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sx-sabreauto.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4600499..f5acbc1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -251,6 +251,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx6q-tx6q-1110.dtb \
imx6sl-evk.dtb \
imx6sx-sdb.dtb \
+ imx6sx-sabreauto.dtb \
ls1021a-qds.dtb \
ls1021a-twr.dtb \
vf500-colibri-eval-v3.dtb \
diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts
new file mode 100644
index 0000000..95f7f0f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts
@@ -0,0 +1,135 @@
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "imx6sx.dtsi"
+
+/ {
+ model = "Freescale i.MX6 SoloX Sabre Auto Board";
+ compatible = "fsl,imx6sx-sabreauto", "fsl,imx6sx";
+
+ memory {
+ reg = <0x80000000 0x80000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_sd3_vmmc: sd3_vmmc{
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_SD3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_1>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3_1>;
+ pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>;
+ bus-width = <8>;
+ cd-gpios = <&gpio7 10 0>;
+ wp-gpios = <&gpio3 19 0>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ vmmc-supply = <®_sd3_vmmc>;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4_3>;
+ bus-width = <8>;
+ cd-gpios = <&gpio7 11 0>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ enable-sdio-wakup;
+ status = "okay";
+};
+
+&iomuxc {
+ imx6x-sabreauto {
+ pinctrl_uart1_1: uart1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc3_1: usdhc3grp {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17059
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10059
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17059
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17059
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17059
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17059
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x17059
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x17059
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x17059
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x17059
+ MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x17059 /* CD */
+ MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x17059 /* WP */
+ >;
+ };
+
+ pinctrl_usdhc3_1_100mhz: usdhc3grp-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170b9
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100b9
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170b9
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170b9
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170b9
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170b9
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170b9
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170b9
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170b9
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_1_200mhz: usdhc3grp-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170f9
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100f9
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170f9
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170f9
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170f9
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170f9
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170f9
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170f9
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170f9
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc4_3: usdhc4grp {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059
+ MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x17059 /* CD */
+ MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */
+ >;
+ };
+ };
+};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 2+ messages in thread[parent not found: <1418022354-21988-1-git-send-email-b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org>]
* Re: [PATCH] arm: dts: imx6sx: add i.mx6sx sabreauto board support [not found] ` <1418022354-21988-1-git-send-email-b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org> @ 2014-12-16 7:55 ` Shawn Guo 0 siblings, 0 replies; 2+ messages in thread From: Shawn Guo @ 2014-12-16 7:55 UTC (permalink / raw) To: Anson Huang Cc: kernel-bIcnvbaLZ9MEGnE8C9+IrQ, devicetree-u79uwXL29TY76Z2rM5mHXA On Mon, Dec 08, 2014 at 03:05:54PM +0800, Anson Huang wrote: > Add basic i.MX6SoloX Sabre Auto board support, currently > only debug UART and uSDHC are supported on this board. > > Signed-off-by: Anson Huang <b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org> Use "ARM: " in the patch prefix. > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6sx-sabreauto.dts | 135 ++++++++++++++++++++++++++++++++ > 2 files changed, 136 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6sx-sabreauto.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 4600499..f5acbc1 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -251,6 +251,7 @@ dtb-$(CONFIG_ARCH_MXC) += \ > imx6q-tx6q-1110.dtb \ > imx6sl-evk.dtb \ > imx6sx-sdb.dtb \ > + imx6sx-sabreauto.dtb \ I just checked my alphabet table, and it tells 'a' goes before 'b'. > ls1021a-qds.dtb \ > ls1021a-twr.dtb \ > vf500-colibri-eval-v3.dtb \ > diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts > new file mode 100644 > index 0000000..95f7f0f > --- /dev/null > +++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts > @@ -0,0 +1,135 @@ > +/* > + * Copyright (C) 2014 Freescale Semiconductor, Inc. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +/dts-v1/; > + > +#include "imx6sx.dtsi" > + > +/ { > + model = "Freescale i.MX6 SoloX Sabre Auto Board"; > + compatible = "fsl,imx6sx-sabreauto", "fsl,imx6sx"; > + > + memory { > + reg = <0x80000000 0x80000000>; > + }; > + > + regulators { > + compatible = "simple-bus"; > + > + reg_sd3_vmmc: sd3_vmmc{ > + compatible = "regulator-fixed"; > + regulator-name = "VCC_SD3"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; Check imx6sx-sdb.dts for examples how we do fixed regulators. > + }; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1_1>; > + status = "okay"; > +}; > + > +&usdhc3 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc3_1>; > + pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>; > + bus-width = <8>; > + cd-gpios = <&gpio7 10 0>; > + wp-gpios = <&gpio3 19 0>; Use GPIO_ACTIVE_HIGH just like what you did for regulator above. > + keep-power-in-suspend; > + enable-sdio-wakeup; > + vmmc-supply = <®_sd3_vmmc>; > + status = "okay"; > +}; > + > +&usdhc4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc4_3>; > + bus-width = <8>; > + cd-gpios = <&gpio7 11 0>; Ditto > + no-1-8-v; > + keep-power-in-suspend; > + enable-sdio-wakup; > + status = "okay"; > +}; > + > +&iomuxc { > + imx6x-sabreauto { > + pinctrl_uart1_1: uart1grp { The label can just be as simple as "pinctrl_uart1". The last number in the name means nothing now, since we define pin groups per board. > + fsl,pins = < > + MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1 > + MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1 > + >; > + }; > + > + pinctrl_usdhc3_1: usdhc3grp { pinctrl_usdhc3 > + fsl,pins = < > + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17059 > + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10059 > + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17059 > + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17059 > + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17059 > + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17059 > + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x17059 > + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x17059 > + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x17059 > + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x17059 > + MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x17059 /* CD */ > + MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x17059 /* WP */ > + >; > + }; > + > + pinctrl_usdhc3_1_100mhz: usdhc3grp-100mhz { pinctrl_usdhc3_100mhz > + fsl,pins = < > + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170b9 > + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100b9 > + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170b9 > + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170b9 > + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170b9 > + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170b9 > + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170b9 > + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170b9 > + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170b9 > + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170b9 > + >; > + }; > + > + pinctrl_usdhc3_1_200mhz: usdhc3grp-200mhz { pinctrl_usdhc3_200mhz > + fsl,pins = < > + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170f9 > + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100f9 > + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170f9 > + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170f9 > + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170f9 > + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170f9 > + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170f9 > + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170f9 > + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170f9 > + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170f9 > + >; > + }; > + > + pinctrl_usdhc4_3: usdhc4grp { pinctrl_usdhc4 Shawn > + fsl,pins = < > + MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059 > + MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059 > + MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059 > + MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059 > + MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059 > + MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059 > + MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x17059 /* CD */ > + MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */ > + >; > + }; > + }; > +}; > -- > 1.7.9.5 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2014-12-16 7:55 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-12-08 7:05 [PATCH] arm: dts: imx6sx: add i.mx6sx sabreauto board support Anson Huang
[not found] ` <1418022354-21988-1-git-send-email-b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
2014-12-16 7:55 ` Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).