* [PATCH V2] ARM: dts: imx6sx: add i.mx6sx sabreauto board support
@ 2014-12-17 4:22 Anson Huang
[not found] ` <1418790129-12879-1-git-send-email-b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
0 siblings, 1 reply; 2+ messages in thread
From: Anson Huang @ 2014-12-17 4:22 UTC (permalink / raw)
To: devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: shawn.guo-QSEj5FYQhm4dnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ
Add basic i.MX6SoloX Sabre Auto board support, currently
only debug UART and uSDHC are supported on this board.
Signed-off-by: Anson Huang <b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
change since V1:
1. correct gpio regulator node;
2. using macro define for GPIO active value;
3. improve pintctrl name;
4. correct the sequence of dtb files in Makefile.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6sx-sabreauto.dts | 146 +++++++++++++++++++++++++++++++++
2 files changed, 147 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sx-sabreauto.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4600499..efe6c73 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -250,6 +250,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx6q-tx6q-1020-comtft.dtb \
imx6q-tx6q-1110.dtb \
imx6sl-evk.dtb \
+ imx6sx-sabreauto.dtb \
imx6sx-sdb.dtb \
ls1021a-qds.dtb \
ls1021a-twr.dtb \
diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts
new file mode 100644
index 0000000..e3c0b63
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts
@@ -0,0 +1,146 @@
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "imx6sx.dtsi"
+
+/ {
+ model = "Freescale i.MX6 SoloX Sabre Auto Board";
+ compatible = "fsl,imx6sx-sabreauto", "fsl,imx6sx";
+
+ memory {
+ reg = <0x80000000 0x80000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vcc_sd3: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_vcc_sd3>;
+ regulator-name = "VCC_SD3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ cd-gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ vmmc-supply = <&vcc_sd3>;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ cd-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ enable-sdio-wakup;
+ status = "okay";
+};
+
+&iomuxc {
+ imx6x-sabreauto {
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17059
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10059
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17059
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17059
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17059
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17059
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x17059
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x17059
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x17059
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x17059
+ MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x17059 /* CD */
+ MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x17059 /* WP */
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170b9
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100b9
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170b9
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170b9
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170b9
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170b9
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170b9
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170b9
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170b9
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170f9
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100f9
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170f9
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170f9
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170f9
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170f9
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170f9
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170f9
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170f9
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059
+ MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x17059 /* CD */
+ MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */
+ >;
+ };
+
+ pinctrl_vcc_sd3: vccsd3grp {
+ fsl,pins = <
+ MX6SX_PAD_KEY_COL1__GPIO2_IO_11 0x17059
+ >;
+ };
+ };
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 2+ messages in thread
end of thread, other threads:[~2015-01-05 13:30 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-12-17 4:22 [PATCH V2] ARM: dts: imx6sx: add i.mx6sx sabreauto board support Anson Huang
[not found] ` <1418790129-12879-1-git-send-email-b20788-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
2015-01-05 13:30 ` Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).