From: Shawn Guo <shawn.guo@linaro.org>
To: Vagrant Cascadian <vagrant@debian.org>,
Peter Chen <peter.chen@freescale.com>
Cc: devicetree@vger.kernel.org,
Andrej Rosano <andrej@inversepath.com>,
Rob Herring <robh+dt@kernel.org>, Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
Russell King <linux@arm.linux.org.uk>,
Sascha Hauer <kernel@pengutronix.de>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] ARM: dts: imx5: Add dts files for USB armory.
Date: Mon, 27 Apr 2015 19:57:48 +0800 [thread overview]
Message-ID: <20150427115747.GA11975@dragon> (raw)
In-Reply-To: <87h9t6i40r.fsf@aikidev.net>
+Peter
On Fri, Mar 27, 2015 at 01:23:00PM -0700, Vagrant Cascadian wrote:
> Add support for the USB armory board by Inverse Path. This board
> features a Freescale iMX53 SoC, 512MB RAM, and USB OTG operating in
> either peripheral or host mode, and 5 GPIO pins.
>
> One .dtb is generated for operating in peripheral mode, and one is
> generated for operating in host mode.
Vagrant,
Does that mean this board can work in peripheral or host mode but can
switch between them at run-time?
Shawn
>
> Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
> Cc: Andrej Rosano <andrej@inversepath.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Pawel Moll <pawel.moll@arm.com>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
> Cc: Kumar Gala <galak@codeaurora.org>
> Cc: Russell King <linux@arm.linux.org.uk>
> Cc: Shawn Guo <shawn.guo@linaro.org>
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: devicetree@vger.kernel.org
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: linux-kernel@vger.kernel.org
> ---
> arch/arm/boot/dts/Makefile | 2 +
> arch/arm/boot/dts/imx53-usbarmory-host_mode.dts | 17 +++
> arch/arm/boot/dts/imx53-usbarmory.dts | 13 ++
> arch/arm/boot/dts/imx53-usbarmory.dtsi | 183 ++++++++++++++++++++++++
> 4 files changed, 215 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx53-usbarmory-host_mode.dts
> create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts
> create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a1c776b..bd2258b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -244,6 +244,8 @@ dtb-$(CONFIG_SOC_IMX53) += \
> imx53-smd.dtb \
> imx53-tx53-x03x.dtb \
> imx53-tx53-x13x.dtb \
> + imx53-usbarmory.dtb \
> + imx53-usbarmory-host_mode.dtb \
> imx53-voipac-bsb.dtb
> dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-aristainetos_4.dtb \
> diff --git a/arch/arm/boot/dts/imx53-usbarmory-host_mode.dts b/arch/arm/boot/dts/imx53-usbarmory-host_mode.dts
> new file mode 100644
> index 0000000..a94cb1d
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx53-usbarmory-host_mode.dts
> @@ -0,0 +1,17 @@
> +/*
> + * Copyright 2015 Inverse Path, S.r.l.
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx53-usbarmory.dtsi"
> +
> +&usbotg {
> + dr_mode = "host";
> +};
> diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/imx53-usbarmory.dts
> new file mode 100644
> index 0000000..c86a4d8
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx53-usbarmory.dts
> @@ -0,0 +1,13 @@
> +/*
> + * Copyright 2015 Inverse Path, S.r.l.
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx53-usbarmory.dtsi"
> diff --git a/arch/arm/boot/dts/imx53-usbarmory.dtsi b/arch/arm/boot/dts/imx53-usbarmory.dtsi
> new file mode 100644
> index 0000000..b4a9052
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx53-usbarmory.dtsi
> @@ -0,0 +1,183 @@
> +/*
> + * Copyright 2015 Inverse Path, S.r.l.
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +#include "imx53.dtsi"
> +
> +/ {
> + model = "Inverse Path USB armory";
> + compatible = "inversepath,imx53-usbarmory", "fsl,imx53";
> +};
> +
> +/ {
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + memory {
> + reg = <0x70000000 0x20000000>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_pin_gpio4_27>;
> +
> + user {
> + label = "LED";
> + gpios = <&gpio4 27 0>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1>;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + imx53-usbarmory {
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000
> + MX53_PAD_GPIO_8__GPIO1_8 0x80000000
> + MX53_PAD_PATA_DATA14__GPIO2_14 0x80000000
> + MX53_PAD_PATA_DATA15__GPIO2_15 0x80000000
> + MX53_PAD_EIM_DA11__GPIO3_11 0x80000000
> + MX53_PAD_EIM_DA12__GPIO3_12 0x80000000
> + MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000
> + MX53_PAD_PATA_DA_2__GPIO7_8 0x80000000
> + MX53_PAD_GPIO_16__GPIO7_11 0x80000000
> + >;
> + };
> +
> + led_pin_gpio4_27: led_gpio4_27@0 {
> + fsl,pins = <
> + MX53_PAD_DISP0_DAT6__GPIO4_27 0x80000000
> + >;
> + };
> +
> + pinctrl_esdhc1: esdhc1grp {
> + fsl,pins = <
> + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
> + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
> + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
> + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
> + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
> + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX53_PAD_CSI0_DAT8__I2C1_SDA 0xc0000000
> + MX53_PAD_CSI0_DAT9__I2C1_SCL 0xc0000000
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
> + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4
> + >;
> + };
> + };
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&vpu {
> + status = "okay";
> +};
> +
> +&usbotg {
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&i2c1 {
> + ltc3589: pmic@34 {
> + compatible = "lltc,ltc3589-2";
> + reg = <0x34>;
> +
> + regulators {
> + sw1_reg: sw1 {
> + regulator-min-microvolt = <591930>;
> + regulator-max-microvolt = <1224671>;
> + lltc,fb-voltage-divider = <100000 158000>;
> + regulator-ramp-delay = <7000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-min-microvolt = <704123>;
> + regulator-max-microvolt = <1456803>;
> + lltc,fb-voltage-divider = <180000 191000>;
> + regulator-ramp-delay = <7000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3_reg: sw3 {
> + regulator-min-microvolt = <1341250>;
> + regulator-max-microvolt = <2775000>;
> + lltc,fb-voltage-divider = <270000 100000>;
> + regulator-ramp-delay = <7000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + bb_out_reg: bb-out {
> + regulator-min-microvolt = <3387341>;
> + regulator-max-microvolt = <3387341>;
> + lltc,fb-voltage-divider = <511000 158000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + ldo1_reg: ldo1 {
> + regulator-min-microvolt = <1306329>;
> + regulator-max-microvolt = <1306329>;
> + lltc,fb-voltage-divider = <100000 158000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: ldo2 {
> + regulator-min-microvolt = <704123>;
> + regulator-max-microvolt = <1456806>;
> + lltc,fb-voltage-divider = <180000 191000>;
> + regulator-ramp-delay = <7000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: ldo3 {
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-boot-on;
> + };
> +
> + ldo4_reg: ldo4 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3200000>;
> + };
> + };
> + };
> +};
> --
> 2.1.4
>
next prev parent reply other threads:[~2015-04-27 11:57 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-03-27 20:23 [PATCH] ARM: dts: imx5: Add dts files for USB armory Vagrant Cascadian
2015-04-27 8:14 ` Shawn Guo
2015-04-27 20:48 ` Vagrant Cascadian
[not found] ` <87y4ldnvqd.fsf-LkDtOWtB3X7R7s880joybQ@public.gmane.org>
2015-05-13 17:53 ` Vagrant Cascadian
[not found] ` <87vbfwe547.fsf-LkDtOWtB3X7R7s880joybQ@public.gmane.org>
2015-05-13 18:08 ` Fabio Estevam
2015-04-27 11:57 ` Shawn Guo [this message]
2015-04-27 13:37 ` Andrej Rosano
[not found] ` <20150427133708.GC11598-GPwhfZ5g21+KIOzWgp228laTQe2KTcn/@public.gmane.org>
2015-04-28 8:20 ` Peter Chen
2015-04-30 2:22 ` Fabio Estevam
2015-04-30 8:51 ` Peter Chen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150427115747.GA11975@dragon \
--to=shawn.guo@linaro.org \
--cc=andrej@inversepath.com \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=peter.chen@freescale.com \
--cc=robh+dt@kernel.org \
--cc=vagrant@debian.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).