[PATCH v6 02/10] DT: Add documentation for the mfd Maxim max77693

[PATCH v6 02/10] DT: Add documentation for the mfd Maxim max77693

[Jacek Anaszewski]

This patch adds device tree binding documentation for
the flash cell of the Maxim max77693 multifunctional device.

Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: devicetree@vger.kernel.org
---
 Documentation/devicetree/bindings/mfd/max77693.txt |   67 ++++++++++++++++++++
 1 file changed, 67 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
index 38e6440..d342584 100644
--- a/Documentation/devicetree/bindings/mfd/max77693.txt
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -76,7 +76,60 @@ Optional properties:
     Valid values: 4300000, 4700000, 4800000, 4900000
     Default: 4300000
 
+- led : the LED submodule device node
+
+There are two LED outputs available - FLED1 and FLED2. Each of them can
+control a separate LED or they can be connected together to double
+the maximum current for a single connected LED. One LED is represented
+by one child node.
+
+Required properties:
+- compatible : Must be "maxim,max77693-led".
+
+Optional properties:
+- maxim,boost-mode :
+	In boost mode the device can produce up to 1.2A of total current
+	on both outputs. The maximum current on each output is reduced
+	to 625mA then. If not enabled explicitly, boost setting defaults to
+	LEDS_BOOST_FIXED in case both current sources are used.
+	Possible values:
+		LEDS_BOOST_OFF (0) - no boost,
+		LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
+		LEDS_BOOST_FIXED (2) - fixed mode.
+- maxim,boost-mvout : Output voltage of the boost module in millivolts.
+	Valid values: 3300 - 5500, step by 25 (rounded down)
+	Default: 3300
+- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
+	if chip estimates that system voltage could drop below this level due
+	to flash power consumption.
+	Valid values: 2400 - 3400, step by 33 (rounded down)
+	Default: 2400
+
+Required properties for the LED child node:
+- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
+		device current output identifiers: 0 - FLED1, 1 - FLED2
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values for a LED connected to one FLED output:
+		15625 - 250000, step by 15625 (rounded down)
+	Valid values for a LED connected to both FLED outputs:
+		15625 - 500000, step by 15625 (rounded down)
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values for a single LED connected to one FLED output
+	(boost mode must be turned off):
+		15625 - 1000000, step by 15625 (rounded down)
+	Valid values for a single LED connected to both FLED outputs:
+		15625 - 1250000, step by 15625 (rounded down)
+	Valid values for two LEDs case:
+		15625 - 625000, step by 15625 (rounded down)
+- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values: 62500 - 1000000, step by 62500 (rounded down)
+
+Optional properties for the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+
 Example:
+#include <dt-bindings/leds/common.h>
+
 	max77693@66 {
 		compatible = "maxim,max77693";
 		reg = <0x66>;
@@ -117,5 +170,19 @@ Example:
 			maxim,thermal-regulation-celsius = <75>;
 			maxim,battery-overcurrent-microamp = <3000000>;
 			maxim,charge-input-threshold-microvolt = <4300000>;
+
+		led {
+			compatible = "maxim,max77693-led";
+			maxim,boost-mode = <LEDS_BOOST_FIXED>;
+			maxim,boost-mvout = <5000>;
+			maxim,mvsys-min = <2400>;
+
+			camera_flash: flash-led {
+				label = "max77693-flash";
+				led-sources = <0>, <1>;
+				led-max-microamp = <500000>;
+				flash-max-microamp = <1250000>;
+				flash-max-timeout-us = <1000000>;
+			};
 		};
 	};
-- 
1.7.9.5

Re: [PATCH v6 02/10] DT: Add documentation for the mfd Maxim max77693

[Lee Jones]

On Tue, 28 Apr 2015, Jacek Anaszewski wrote:

> This patch adds device tree binding documentation for
> the flash cell of the Maxim max77693 multifunctional device.
> 
> Signed-off-by: Jacek Anaszewski <j.anaszewski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> Signed-off-by: Andrzej Hajda <a.hajda-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> Acked-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> Acked-by: Sakari Ailus <sakari.ailus-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
> Cc: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> Cc: Chanwoo Choi <cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> Cc: Bryan Wu <cooloney-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> Cc: Richard Purdie <rpurdie-Fm38FmjxZ/leoWH0uzbU5w@public.gmane.org>
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> ---
>  Documentation/devicetree/bindings/mfd/max77693.txt |   67 ++++++++++++++++++++
>  1 file changed, 67 insertions(+)

Requires a LED Ack.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v6 02/10] DT: Add documentation for the mfd Maxim max77693

[Bryan Wu]

On Tue, Apr 28, 2015 at 3:09 AM, Lee Jones <lee.jones@linaro.org> wrote:
> On Tue, 28 Apr 2015, Jacek Anaszewski wrote:
>
>> This patch adds device tree binding documentation for
>> the flash cell of the Maxim max77693 multifunctional device.
>>
>> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
>> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
>> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
>> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
>> Cc: Lee Jones <lee.jones@linaro.org>
>> Cc: Chanwoo Choi <cw00.choi@samsung.com>
>> Cc: Bryan Wu <cooloney@gmail.com>
>> Cc: Richard Purdie <rpurdie@rpsys.net>
>> Cc: devicetree@vger.kernel.org
>> ---
>>  Documentation/devicetree/bindings/mfd/max77693.txt |   67 ++++++++++++++++++++
>>  1 file changed, 67 insertions(+)
>
> Requires a LED Ack.
>

Please go with my Ack:

Acked-by: Bryan Wu <cooloney@gmail.com>

Thanks,
-Bryan

Re: [PATCH v6 02/10] DT: Add documentation for the mfd Maxim max77693

[Lee Jones]

On Tue, 28 Apr 2015, Jacek Anaszewski wrote:

> This patch adds device tree binding documentation for
> the flash cell of the Maxim max77693 multifunctional device.
> 
> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
> Cc: Lee Jones <lee.jones@linaro.org>
> Cc: Chanwoo Choi <cw00.choi@samsung.com>
> Cc: Bryan Wu <cooloney@gmail.com>
> Cc: Richard Purdie <rpurdie@rpsys.net>
> Cc: devicetree@vger.kernel.org
> ---
>  Documentation/devicetree/bindings/mfd/max77693.txt |   67 ++++++++++++++++++++
>  1 file changed, 67 insertions(+)

Applied with Bryan's Ack.

> diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
> index 38e6440..d342584 100644
> --- a/Documentation/devicetree/bindings/mfd/max77693.txt
> +++ b/Documentation/devicetree/bindings/mfd/max77693.txt
> @@ -76,7 +76,60 @@ Optional properties:
>      Valid values: 4300000, 4700000, 4800000, 4900000
>      Default: 4300000
>  
> +- led : the LED submodule device node
> +
> +There are two LED outputs available - FLED1 and FLED2. Each of them can
> +control a separate LED or they can be connected together to double
> +the maximum current for a single connected LED. One LED is represented
> +by one child node.
> +
> +Required properties:
> +- compatible : Must be "maxim,max77693-led".
> +
> +Optional properties:
> +- maxim,boost-mode :
> +	In boost mode the device can produce up to 1.2A of total current
> +	on both outputs. The maximum current on each output is reduced
> +	to 625mA then. If not enabled explicitly, boost setting defaults to
> +	LEDS_BOOST_FIXED in case both current sources are used.
> +	Possible values:
> +		LEDS_BOOST_OFF (0) - no boost,
> +		LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
> +		LEDS_BOOST_FIXED (2) - fixed mode.
> +- maxim,boost-mvout : Output voltage of the boost module in millivolts.
> +	Valid values: 3300 - 5500, step by 25 (rounded down)
> +	Default: 3300
> +- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
> +	if chip estimates that system voltage could drop below this level due
> +	to flash power consumption.
> +	Valid values: 2400 - 3400, step by 33 (rounded down)
> +	Default: 2400
> +
> +Required properties for the LED child node:
> +- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
> +		device current output identifiers: 0 - FLED1, 1 - FLED2
> +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
> +	Valid values for a LED connected to one FLED output:
> +		15625 - 250000, step by 15625 (rounded down)
> +	Valid values for a LED connected to both FLED outputs:
> +		15625 - 500000, step by 15625 (rounded down)
> +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
> +	Valid values for a single LED connected to one FLED output
> +	(boost mode must be turned off):
> +		15625 - 1000000, step by 15625 (rounded down)
> +	Valid values for a single LED connected to both FLED outputs:
> +		15625 - 1250000, step by 15625 (rounded down)
> +	Valid values for two LEDs case:
> +		15625 - 625000, step by 15625 (rounded down)
> +- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
> +	Valid values: 62500 - 1000000, step by 62500 (rounded down)
> +
> +Optional properties for the LED child node:
> +- label : see Documentation/devicetree/bindings/leds/common.txt
> +
>  Example:
> +#include <dt-bindings/leds/common.h>
> +
>  	max77693@66 {
>  		compatible = "maxim,max77693";
>  		reg = <0x66>;
> @@ -117,5 +170,19 @@ Example:
>  			maxim,thermal-regulation-celsius = <75>;
>  			maxim,battery-overcurrent-microamp = <3000000>;
>  			maxim,charge-input-threshold-microvolt = <4300000>;
> +
> +		led {
> +			compatible = "maxim,max77693-led";
> +			maxim,boost-mode = <LEDS_BOOST_FIXED>;
> +			maxim,boost-mvout = <5000>;
> +			maxim,mvsys-min = <2400>;
> +
> +			camera_flash: flash-led {
> +				label = "max77693-flash";
> +				led-sources = <0>, <1>;
> +				led-max-microamp = <500000>;
> +				flash-max-microamp = <1250000>;
> +				flash-max-timeout-us = <1000000>;
> +			};
>  		};
>  	};

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v6 04/10] DT: Add documentation for the Skyworks AAT1290

[Jacek Anaszewski]

This patch adds device tree binding documentation for
1.5A Step-Up Current Regulator for Flash LEDs.

Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: devicetree@vger.kernel.org
---
 .../devicetree/bindings/leds/leds-aat1290.txt      |   41 ++++++++++++++++++++
 1 file changed, 41 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-aat1290.txt

diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
new file mode 100644
index 0000000..ef88b9c
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
@@ -0,0 +1,41 @@
+* Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs
+
+The device is controlled through two pins: FL_EN and EN_SET. The pins when,
+asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
+respectively.
+
+Required properties:
+
+- compatible : Must be "skyworks,aat1290".
+- flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
+- enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
+
+A discrete LED element connected to the device must be represented by a child
+node - see Documentation/devicetree/bindings/leds/common.txt.
+
+Required properties of the LED child node:
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+                       Maximum flash LED supply current can be calculated using
+                       following formula: I = 1A * 162kohm / Rset.
+- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+                     Maximum flash timeout can be calculated using following
+                     formula: T = 8.82 * 10^9 * Ct.
+
+Optional properties of the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+
+Example (by Ct = 220nF, Rset = 160kohm):
+
+aat1290 {
+	compatible = "skyworks,aat1290";
+	flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
+	enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
+
+	camera_flash: flash-led {
+		label = "aat1290-flash";
+		led-max-microamp = <520833>;
+		flash-max-microamp = <1012500>;
+		flash-timeout-us = <1940000>;
+	};
+};
-- 
1.7.9.5

Re: [PATCH v6 04/10] DT: Add documentation for the Skyworks AAT1290

[Bryan Wu]

On Tue, Apr 28, 2015 at 12:18 AM, Jacek Anaszewski
<j.anaszewski@samsung.com> wrote:
> This patch adds device tree binding documentation for
> 1.5A Step-Up Current Regulator for Flash LEDs.
>

Applied, thanks,
-Bryan

> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
> Cc: Bryan Wu <cooloney@gmail.com>
> Cc: Richard Purdie <rpurdie@rpsys.net>
> Cc: devicetree@vger.kernel.org
> ---
>  .../devicetree/bindings/leds/leds-aat1290.txt      |   41 ++++++++++++++++++++
>  1 file changed, 41 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/leds-aat1290.txt
>
> diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
> new file mode 100644
> index 0000000..ef88b9c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
> @@ -0,0 +1,41 @@
> +* Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs
> +
> +The device is controlled through two pins: FL_EN and EN_SET. The pins when,
> +asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
> +respectively.
> +
> +Required properties:
> +
> +- compatible : Must be "skyworks,aat1290".
> +- flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
> +- enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
> +
> +A discrete LED element connected to the device must be represented by a child
> +node - see Documentation/devicetree/bindings/leds/common.txt.
> +
> +Required properties of the LED child node:
> +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
> +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
> +                       Maximum flash LED supply current can be calculated using
> +                       following formula: I = 1A * 162kohm / Rset.
> +- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
> +                     Maximum flash timeout can be calculated using following
> +                     formula: T = 8.82 * 10^9 * Ct.
> +
> +Optional properties of the LED child node:
> +- label : see Documentation/devicetree/bindings/leds/common.txt
> +
> +Example (by Ct = 220nF, Rset = 160kohm):
> +
> +aat1290 {
> +       compatible = "skyworks,aat1290";
> +       flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
> +       enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
> +
> +       camera_flash: flash-led {
> +               label = "aat1290-flash";
> +               led-max-microamp = <520833>;
> +               flash-max-microamp = <1012500>;
> +               flash-timeout-us = <1940000>;
> +       };
> +};
> --
> 1.7.9.5
>

[PATCH v6 09/10] DT: aat1290: Document handling external strobe sources

[Jacek Anaszewski]

This patch adds documentation for a pinctrl-names property.
The property, when present, is used for switching the source
of the strobe signal for the device.

Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: devicetree@vger.kernel.org
---
 .../devicetree/bindings/leds/leds-aat1290.txt      |   36 ++++++++++++++++++--
 1 file changed, 34 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
index ef88b9c..c05ed91 100644
--- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt
+++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
@@ -2,7 +2,9 @@
 
 The device is controlled through two pins: FL_EN and EN_SET. The pins when,
 asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
-respectively.
+respectively. In order to add a capability of selecting the strobe signal source
+(e.g. CPU or camera sensor) there is an additional switch required, independent
+of the flash chip. The switch is controlled with pin control.
 
 Required properties:
 
@@ -10,6 +12,13 @@ Required properties:
 - flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
 - enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
 
+Optional properties:
+- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
+		"default" and "host" must refer to the same pin configuration
+		node, which sets the host as a strobe signal provider. Entry
+		"isp" must refer to the pin configuration node, which sets the
+		ISP as a strobe signal provider.
+
 A discrete LED element connected to the device must be represented by a child
 node - see Documentation/devicetree/bindings/leds/common.txt.
 
@@ -25,13 +34,22 @@ Required properties of the LED child node:
 Optional properties of the LED child node:
 - label : see Documentation/devicetree/bindings/leds/common.txt
 
-Example (by Ct = 220nF, Rset = 160kohm):
+Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with
+a switch that allows for routing strobe signal either from the host or from
+the camera sensor):
+
+#include "exynos4412.dtsi"
 
 aat1290 {
 	compatible = "skyworks,aat1290";
 	flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
 	enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
 
+	pinctrl-names = "default", "host", "isp";
+	pinctrl-0 = <&camera_flash_host>;
+	pinctrl-1 = <&camera_flash_host>;
+	pinctrl-2 = <&camera_flash_isp>;
+
 	camera_flash: flash-led {
 		label = "aat1290-flash";
 		led-max-microamp = <520833>;
@@ -39,3 +57,17 @@ aat1290 {
 		flash-timeout-us = <1940000>;
 	};
 };
+
+&pinctrl_0 {
+	camera_flash_host: camera-flash-host {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <0>;
+	};
+
+	camera_flash_isp: camera-flash-isp {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <1>;
+	};
+};
-- 
1.7.9.5