From: Lee Jones <lee.jones@linaro.org>
To: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: cw00.choi@samsung.com, myungjoo.ham@samsung.com,
linux-kernel@vger.kernel.org,
patches@opensource.wolfsonmicro.com, devicetree@vger.kernel.org
Subject: Re: [PATCH v3 6/7] mfd: arizona: Update DT doc for new mic detection bindings
Date: Wed, 24 Jun 2015 15:15:34 +0100 [thread overview]
Message-ID: <20150624141534.GN15013@x1> (raw)
In-Reply-To: <1434709467-28147-7-git-send-email-ckeepax@opensource.wolfsonmicro.com>
This requires a DT Ack.
[... which would be pretty difficult, as you didn't Cc them]
> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
> ---
> Documentation/devicetree/bindings/mfd/arizona.txt | 16 ++++++++++++++++
> 1 files changed, 16 insertions(+), 0 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt
> index 32a71b7..8d92c92 100644
> --- a/Documentation/devicetree/bindings/mfd/arizona.txt
> +++ b/Documentation/devicetree/bindings/mfd/arizona.txt
> @@ -68,6 +68,22 @@ Optional properties:
> If this node is not mentioned or if the value is unknown, then
> headphone detection mode is set to HPDETL.
>
> + - wlf,micd-detect-debounce : Additional software microphone detection
> + debounce specified in milliseconds.
> + - wlf,micd-pol-gpio : GPIO specifier for the GPIO controlling the headset
> + polarity if one exists.
> + - wlf,micd-bias-start-time : Time allowed for MICBIAS to startup prior to
> + performing microphone detection, specified as per the ARIZONA_MICD_TIME_XXX
> + defines.
> + - wlf,micd-rate : Delay between successive microphone detection measurements,
> + specified as per the ARIZONA_MICD_TIME_XXX defines.
> + - wlf,micd-dbtime : Microphone detection hardware debounces specified as the
> + number of measurements to take, valid values being 2 and 4.
> + - wlf,micd-timeout : Timeout for microphone detection, specified in
> + milliseconds.
> + - wlf,micd-force-micbias : Force MICBIAS continuously on during microphone
> + detection.
> +
> - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if
> they are being externally supplied. As covered in
> Documentation/devicetree/bindings/regulator/regulator.txt
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
next parent reply other threads:[~2015-06-24 14:15 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <1434709467-28147-1-git-send-email-ckeepax@opensource.wolfsonmicro.com>
[not found] ` <1434709467-28147-7-git-send-email-ckeepax@opensource.wolfsonmicro.com>
2015-06-24 14:15 ` Lee Jones [this message]
2015-06-24 15:41 ` [PATCH v3 6/7] mfd: arizona: Update DT doc for new mic detection bindings Charles Keepax
[not found] ` <20150624154139.GD6321-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2015-06-25 8:53 ` Lee Jones
2015-06-19 10:33 [PATCH v3 0/7] Add basic microphone " Charles Keepax
[not found] ` <1434709989-28300-1-git-send-email-ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2015-06-19 10:33 ` [PATCH v3 6/7] mfd: arizona: Update DT doc for new mic " Charles Keepax
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150624141534.GN15013@x1 \
--to=lee.jones@linaro.org \
--cc=ckeepax@opensource.wolfsonmicro.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=myungjoo.ham@samsung.com \
--cc=patches@opensource.wolfsonmicro.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).