From: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
To: Richard Fitzgerald
<rf-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
Cc: sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org,
patches-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Re: [PATCH V4 2/3] mfd: arizona: factor out checking of jack detection state
Date: Wed, 12 Aug 2015 15:45:27 +0100 [thread overview]
Message-ID: <20150812144527.GI18282@x1> (raw)
In-Reply-To: <1439380692-7848-3-git-send-email-rf-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
On Wed, 12 Aug 2015, Richard Fitzgerald wrote:
> Currently runtime_suspend will fully power off the codec if
> the jack detection is not enabled. Not all future codecs will
> have jack detection so to prepare for these codecs this patch
> factors out the check so that it be called as needed in the
> existing codec-specific switch cases.
>
> Signed-off-by: Richard Fitzgerald <rf-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
> ---
> drivers/mfd/arizona-core.c | 41 ++++++++++++++++++++++++++++++++---------
> 1 file changed, 32 insertions(+), 9 deletions(-)
For my own reference:
Acked-by: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
> index 33f3db4..43ca30b 100644
> --- a/drivers/mfd/arizona-core.c
> +++ b/drivers/mfd/arizona-core.c
> @@ -489,6 +489,23 @@ static int arizona_connect_dcvdd(struct arizona *arizona)
> return ret;
> }
>
> +static int arizona_is_jack_det_active(struct arizona *arizona)
> +{
> + unsigned int val;
> + int ret;
> +
> + ret = regmap_read(arizona->regmap, ARIZONA_JACK_DETECT_ANALOGUE, &val);
> + if (ret) {
> + dev_err(arizona->dev,
> + "Failed to check jack det status: %d\n", ret);
> + return ret;
> + } else if (val & ARIZONA_JD1_ENA) {
> + return 1;
> + } else {
> + return 0;
> + }
> +}
> +
> static int arizona_runtime_resume(struct device *dev)
> {
> struct arizona *arizona = dev_get_drvdata(dev);
> @@ -613,20 +630,18 @@ err:
> static int arizona_runtime_suspend(struct device *dev)
> {
> struct arizona *arizona = dev_get_drvdata(dev);
> - unsigned int val;
> + unsigned int jd_active = 0;
> int ret;
>
> dev_dbg(arizona->dev, "Entering AoD mode\n");
>
> - ret = regmap_read(arizona->regmap, ARIZONA_JACK_DETECT_ANALOGUE, &val);
> - if (ret) {
> - dev_err(dev, "Failed to check jack det status: %d\n", ret);
> - return ret;
> - }
> -
> switch (arizona->type) {
> case WM5110:
> case WM8280:
> + jd_active = arizona_is_jack_det_active(arizona);
> + if (jd_active < 0)
> + return jd_active;
> +
> if (arizona->external_dcvdd) {
> ret = arizona_isolate_dcvdd(arizona);
> if (ret != 0)
> @@ -648,13 +663,17 @@ static int arizona_runtime_suspend(struct device *dev)
> }
> break;
> case WM5102:
> + jd_active = arizona_is_jack_det_active(arizona);
> + if (jd_active < 0)
> + return jd_active;
> +
> if (arizona->external_dcvdd) {
> ret = arizona_isolate_dcvdd(arizona);
> if (ret != 0)
> return ret;
> }
>
> - if (!(val & ARIZONA_JD1_ENA)) {
> + if (!jd_active) {
> ret = regmap_write(arizona->regmap,
> ARIZONA_WRITE_SEQUENCER_CTRL_3, 0x0);
> if (ret) {
> @@ -666,6 +685,10 @@ static int arizona_runtime_suspend(struct device *dev)
> }
> break;
> default:
> + jd_active = arizona_is_jack_det_active(arizona);
> + if (jd_active < 0)
> + return jd_active;
> +
> if (arizona->external_dcvdd) {
> ret = arizona_isolate_dcvdd(arizona);
> if (ret != 0)
> @@ -679,7 +702,7 @@ static int arizona_runtime_suspend(struct device *dev)
> regulator_disable(arizona->dcvdd);
>
> /* Allow us to completely power down if no jack detection */
> - if (!(val & ARIZONA_JD1_ENA)) {
> + if (!jd_active) {
> dev_dbg(arizona->dev, "Fully powering off\n");
>
> arizona->has_fully_powered_off = true;
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2015-08-12 14:45 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-08-12 11:58 [PATCH V4 0/3] mfd: arizona: Support Cirrus Logic CS47L24 and WM1831 Richard Fitzgerald
2015-08-12 11:58 ` [PATCH V4 1/3] mfd: arizona: factor out DCVDD isolation control Richard Fitzgerald
[not found] ` <1439380692-7848-2-git-send-email-rf-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2015-08-12 14:42 ` Lee Jones
2015-08-12 11:58 ` [PATCH V4 2/3] mfd: arizona: factor out checking of jack detection state Richard Fitzgerald
[not found] ` <1439380692-7848-3-git-send-email-rf-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2015-08-12 14:45 ` Lee Jones [this message]
2015-08-12 11:58 ` [PATCH V4 3/3] mfd: arizona: Support Cirrus Logic CS47L24 and WM1831 Richard Fitzgerald
2015-08-14 6:40 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150812144527.GI18282@x1 \
--to=lee.jones-qsej5fyqhm4dnm+yrofe0a@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=patches-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org \
--cc=rf-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org \
--cc=sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).