Re: [PATCH 2/2] mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller.

[Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>]

On Monday, August 31, 2015 at 07:30:37 PM, Graham Moore wrote:
> Hi Marek,

Hi Graham,

> Having some compile issues...see below
> 
> On 08/21/2015 04:20 AM, Marek Vasut wrote:
> > From: Graham Moore <grmoore-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>
> > 
> > Add support for the Cadence QSPI controller. This controller is
> > present in the Altera SoCFPGA SoCs and this driver has been tested
> > on the Cyclone V SoC.
> > 
> > Signed-off-by: Graham Moore <grmoore-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>
> > Signed-off-by: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>
> 
> [...]
> 
> > +static int cqspi_set_protocol(struct spi_nor *nor, enum spi_protocol
> > proto) +{
> > +	struct cqspi_flash_pdata *f_pdata = nor->priv;
> > +
> > +	switch (proto) {
> > +	case SPI_PROTO_1_1_1:
> > +	case SPI_PROTO_1_1_2:
> > +	case SPI_PROTO_1_1_4:
> > +	case SPI_PROTO_1_2_2:
> > +	case SPI_PROTO_1_4_4:
> > +		f_pdata->inst_width = CQSPI_INST_TYPE_SINGLE;
> > +		break;
> > +	case SPI_PROTO_2_2_2:
> > +		f_pdata->inst_width = CQSPI_INST_TYPE_DUAL;
> > +		break;
> > +	case SPI_PROTO_4_4_4:
> > +		f_pdata->inst_width = CQSPI_INST_TYPE_QUAD;
> > +		break;
> > +	default:
> > +		return -EINVAL;
> > +	}
> > +
> > +	switch (proto) {
> > +	case SPI_PROTO_1_1_1:
> > +	case SPI_PROTO_1_1_2:
> > +	case SPI_PROTO_1_1_4:
> > +		f_pdata->addr_width = CQSPI_INST_TYPE_SINGLE;
> > +		break;
> > +	case SPI_PROTO_1_2_2:
> > +	case SPI_PROTO_2_2_2:
> > +		f_pdata->addr_width = CQSPI_INST_TYPE_DUAL;
> > +		break;
> > +	case SPI_PROTO_1_4_4:
> > +	case SPI_PROTO_4_4_4:
> > +		f_pdata->addr_width = CQSPI_INST_TYPE_QUAD;
> > +		break;
> > +	default:
> > +		return -EINVAL;
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> 
> I think you have some other patches in your tree, the above doesn't
> compile on l2-mtd/master:
> 
> ~/l2-mtd/drivers/mtd/spi-nor/cadence-quadspi.c:701:57: warning: ‘enum
> spi_protocol’ declared inside parameter list [enabled by default]
> ~/l2-mtd/drivers/mtd/spi-nor/cadence-quadspi.c:701:57: warning: its
> scope is only this definition or declaration, which is probably not what
> you want [enabled by default]
> ~/l2-mtd/drivers/mtd/spi-nor/cadence-quadspi.c:701:70: error: parameter
> 2 (‘proto’) has incomplete type

It's in the V7 changelog, you need:

mtd: spi-nor: notify (Q)SPI controller about protocol change

Also, since V8, you will need:

mtd: spi-nor: Decouple SPI NOR's device_node from controller device

They're both in the linux-mtd list, so feel free to pick them from there.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html