From: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
To: cw00.choi@samsung.com, lee.jones@linaro.org
Cc: myungjoo.ham@samsung.com, sameo@linux.intel.com,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
patches@opensource.wolfsonmicro.com
Subject: [PATCH v3 1/6] mfd: arizona: Add TST_CAP bits for headphone detection
Date: Fri, 11 Sep 2015 13:37:57 +0100 [thread overview]
Message-ID: <20150911123757.GC11200@ck-lbox> (raw)
In-Reply-To: <20150911122451.GB11200@ck-lbox>
On Florida some additional settings are required to get accurate
measurements at the top end of the headphone detection range. This patch
adds the bits required for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
---
Changes since v2:
- Removed accidental addition of Chanwoo's ack.
Thanks,
Charles
drivers/mfd/wm5110-tables.c | 2 ++
include/linux/mfd/arizona/registers.h | 8 ++++++++
2 files changed, 10 insertions(+), 0 deletions(-)
diff --git a/drivers/mfd/wm5110-tables.c b/drivers/mfd/wm5110-tables.c
index acb3bb2..78032e8 100644
--- a/drivers/mfd/wm5110-tables.c
+++ b/drivers/mfd/wm5110-tables.c
@@ -1908,6 +1908,7 @@ static bool wm5110_readable_register(struct device *dev, unsigned int reg)
case ARIZONA_HP1_SHORT_CIRCUIT_CTRL:
case ARIZONA_HP2_SHORT_CIRCUIT_CTRL:
case ARIZONA_HP3_SHORT_CIRCUIT_CTRL:
+ case ARIZONA_HP_TEST_CTRL_1:
case ARIZONA_AIF1_BCLK_CTRL:
case ARIZONA_AIF1_TX_PIN_CTRL:
case ARIZONA_AIF1_RX_PIN_CTRL:
@@ -2853,6 +2854,7 @@ static bool wm5110_volatile_register(struct device *dev, unsigned int reg)
case ARIZONA_INPUT_ENABLES_STATUS:
case ARIZONA_OUTPUT_STATUS_1:
case ARIZONA_RAW_OUTPUT_STATUS_1:
+ case ARIZONA_HP_TEST_CTRL_1:
case ARIZONA_SLIMBUS_RX_PORT_STATUS:
case ARIZONA_SLIMBUS_TX_PORT_STATUS:
case ARIZONA_INTERRUPT_STATUS_1:
diff --git a/include/linux/mfd/arizona/registers.h b/include/linux/mfd/arizona/registers.h
index e96644c..fe1b5d0 100644
--- a/include/linux/mfd/arizona/registers.h
+++ b/include/linux/mfd/arizona/registers.h
@@ -237,6 +237,7 @@
#define ARIZONA_HP1_SHORT_CIRCUIT_CTRL 0x4A0
#define ARIZONA_HP2_SHORT_CIRCUIT_CTRL 0x4A1
#define ARIZONA_HP3_SHORT_CIRCUIT_CTRL 0x4A2
+#define ARIZONA_HP_TEST_CTRL_1 0x4A4
#define ARIZONA_SPK_CTRL_2 0x4B5
#define ARIZONA_SPK_CTRL_3 0x4B6
#define ARIZONA_DAC_COMP_1 0x4DC
@@ -3548,6 +3549,13 @@
#define ARIZONA_HP3_SC_ENA_WIDTH 1 /* HP3_SC_ENA */
/*
+ * R1188 (0x4A4) HP Test Ctrl 1
+ */
+#define ARIZONA_HP1_TST_CAP_SEL_MASK 0x0003 /* HP1_TST_CAP_SEL - [1:0] */
+#define ARIZONA_HP1_TST_CAP_SEL_SHIFT 0 /* HP1_TST_CAP_SEL - [1:0] */
+#define ARIZONA_HP1_TST_CAP_SEL_WIDTH 2 /* HP1_TST_CAP_SEL - [1:0] */
+
+/*
* R1244 (0x4DC) - DAC comp 1
*/
#define ARIZONA_OUT_COMP_COEFF_MASK 0xFFFF /* OUT_COMP_COEFF - [15:0] */
--
1.7.2.5
next prev parent reply other threads:[~2015-09-11 12:37 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-11 12:14 [PATCH v2 0/6] Arizona extcon improvements Charles Keepax
[not found] ` <1441973658-26234-1-git-send-email-ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2015-09-11 12:14 ` [PATCH v2 1/6] mfd: arizona: Add TST_CAP bits for headphone detection Charles Keepax
[not found] ` <1441973658-26234-2-git-send-email-ckeepax-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2015-09-11 12:24 ` Charles Keepax
2015-09-11 12:37 ` Charles Keepax [this message]
2015-09-15 4:05 ` [PATCH v3 " Chanwoo Choi
2015-09-15 9:33 ` Charles Keepax
2015-09-11 12:14 ` [PATCH v2 2/6] extcon: arizona: Additional settings to improve accuracy of HP detect Charles Keepax
2015-09-11 12:14 ` [PATCH v2 4/6] extcon: arizona: Add device binding for jack detect polarity inversion Charles Keepax
2015-09-11 12:14 ` [PATCH v2 6/6] mfd: arizona: Update DT binding documentation for jack detection Charles Keepax
2015-09-11 12:14 ` [PATCH v2 3/6] extcon: arizona: Ignore jd_invert for MICD_CLAMP_STS Charles Keepax
2015-09-11 12:14 ` [PATCH v2 5/6] extcon: arizona: Add device binding for second jack detect pin on GPIO5 Charles Keepax
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150911123757.GC11200@ck-lbox \
--to=ckeepax@opensource.wolfsonmicro.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=lee.jones@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=myungjoo.ham@samsung.com \
--cc=patches@opensource.wolfsonmicro.com \
--cc=sameo@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).