[PATCH v4 1/8] pinctrl: freescale: imx: fix system crash if enable two pinctl instances

[PATCH v4 1/8] pinctrl: freescale: imx: fix system crash if enable two pinctl instances

[Adrian Alonso]

From: Robin Gong <b38343-KZfg59tc24xl57MIdRCFDg@public.gmane.org>

Fix system chrash caused by groups whose number is smaller than the number
of groups of the last pinctl instance which is not initialized.

iMX7D supports two iomux controllers (iomuxc-lpsr and iomuxc) on probing
the second instance (iomuxc) the chrash below occurs.

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.2.0-next-20150901-00006-gebfa43c (aalonso@bluefly)
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7)
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasin instruction cache
[    0.000000] Machine model: Freescale i.MX7 SabreSD Board
[    0.661012] [<802a6cb0>] (strcmp) from [<802cc80c>] (imx_dt_node_to_map+0x58/0x208)
[    0.668879] [<802cc80c>] (imx_dt_node_to_map) from [<802cbe24>] (pinctrl_dt_to_map+0x174/0x2b0)
[    0.677654] [<802cbe24>] (pinctrl_dt_to_map) from [<802c8f18>] (pinctrl_get+0x100/0x424)
[    0.685878] [<802c8f18>] (pinctrl_get) from [<802c9510>] (pinctrl_register+0x26c/0x480)
[    0.694104] [<802c9510>] (pinctrl_register) from [<802ccf3c>] (imx_pinctrl_probe+0x580/0x6e8)
[    0.702706] [<802ccf3c>] (imx_pinctrl_probe) from [<80351b58>] (platform_drv_probe+0x44/0xa4)
[    0.711455] [<80351b58>] (platform_drv_probe) from [<803503ec>] (driver_probe_device+0x174/0x2b4)
[    0.720405] [<803503ec>] (driver_probe_device) from [<803505fc>] (__driver_attach+0x8c/0x90)
[    0.728982] [<803505fc>] (__driver_attach) from [<8034e930>] (bus_for_each_dev+0x6c/0xa0)
[    0.737381] [<8034e930>] (bus_for_each_dev) from [<8034fb88>] (bus_add_driver+0x148/0x1f0)
[    0.745804] [<8034fb88>] (bus_add_driver) from [<80350c00>] (driver_register+0x78/0xf8)
[    0.753880] [<80350c00>] (driver_register) from [<800097d0>] (do_one_initcall+0x8c/0x1d4)
[    0.762282] [<800097d0>] (do_one_initcall) from [<80987dac>] (kernel_init_freeable+0x144/0x1e4)
[    0.771061] [<80987dac>] (kernel_init_freeable) from [<806d9c7c>] (kernel_init+0x8/0xe8)
[    0.779285] [<806d9c7c>] (kernel_init) from [<8000f628>] (ret_from_fork+0x14/0x2c)
[    0.786981] Code: e3520000 e5e32001 1afffffb e12fff1e (e4d03001)

Signed-off-by: Robin Gong <b38343-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Adrian Alonso <aalonso-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
Chages for V2:
- Reorder patch series
- Add platform boot up information on kernel error
- Move gpr_index to imx_pinctrl_soc_info
Changes for V3:
- Rename grp_index to group_index
Changes for V4: Resend

 drivers/pinctrl/freescale/pinctrl-imx.c | 3 +--
 drivers/pinctrl/freescale/pinctrl-imx.h | 1 +
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/freescale/pinctrl-imx.c b/drivers/pinctrl/freescale/pinctrl-imx.c
index d7b98ba..b9c6deb 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.c
+++ b/drivers/pinctrl/freescale/pinctrl-imx.c
@@ -580,7 +580,6 @@ static int imx_pinctrl_parse_functions(struct device_node *np,
 	struct device_node *child;
 	struct imx_pmx_func *func;
 	struct imx_pin_group *grp;
-	static u32 grp_index;
 	u32 i = 0;
 
 	dev_dbg(info->dev, "parse function(%d): %s\n", index, np->name);
@@ -599,7 +598,7 @@ static int imx_pinctrl_parse_functions(struct device_node *np,
 
 	for_each_child_of_node(np, child) {
 		func->groups[i] = child->name;
-		grp = &info->groups[grp_index++];
+		grp = &info->groups[info->group_index++];
 		imx_pinctrl_parse_groups(child, grp, info, i++);
 	}
 
diff --git a/drivers/pinctrl/freescale/pinctrl-imx.h b/drivers/pinctrl/freescale/pinctrl-imx.h
index 49e55d3..2a5fe72 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.h
+++ b/drivers/pinctrl/freescale/pinctrl-imx.h
@@ -78,6 +78,7 @@ struct imx_pinctrl_soc_info {
 	struct imx_pin_reg *pin_regs;
 	struct imx_pin_group *groups;
 	unsigned int ngroups;
+	unsigned int group_index;
 	struct imx_pmx_func *functions;
 	unsigned int nfunctions;
 	unsigned int flags;
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 2/8] ARM: imx: imx7d-pinfunc: add gpio1 pad iomux settings

[Adrian Alonso]

- Add imx7 SoC GPIO1 pad iomuxc settings
  <mux_reg conf_reg input_reg mux_mode input_val>
- Fix UART input select daisy chain setting values

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Chages for V2: Fix tab+space identation
Chages for V3: Resend
Chages for V4: Resend

 arch/arm/boot/dts/imx7d-pinfunc.h | 122 +++++++++++++++++++++++++++++++++++++-
 1 file changed, 119 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/imx7d-pinfunc.h b/arch/arm/boot/dts/imx7d-pinfunc.h
index a8d8149..eeda783 100644
--- a/arch/arm/boot/dts/imx7d-pinfunc.h
+++ b/arch/arm/boot/dts/imx7d-pinfunc.h
@@ -15,6 +15,122 @@
  * <mux_reg conf_reg input_reg mux_mode input_val>
  */
 
+#define MX7D_PAD_GPIO1_IO00__GPIO1_IO0                            0x0000 0x0030 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO00__PWM4_OUT                             0x0000 0x0030 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_ANY                       0x0000 0x0030 0x0000 0x2 0x0
+#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_B                         0x0000 0x0030 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG__RST_B_DEB                0x0000 0x0030 0x0000 0x4 0x0
+#define MX7D_PAD_GPIO1_IO01__GPIO1_IO1                            0x0004 0x0034 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO01__PWM1_OUT                             0x0004 0x0034 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO01__CCM_ENET_REF_CLK3                    0x0004 0x0034 0x0000 0x2 0x0
+#define MX7D_PAD_GPIO1_IO01__SAI1_MCLK                            0x0004 0x0034 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO01__ANATOP_24M_OUT                       0x0004 0x0034 0x0000 0x4 0x0
+#define MX7D_PAD_GPIO1_IO01__OBSERVE0_OUT                         0x0004 0x0034 0x0000 0x6 0x0
+#define MX7D_PAD_GPIO1_IO02__GPIO1_IO2                            0x0008 0x0038 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO02__PWM2_OUT                             0x0008 0x0038 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO02__CCM_ENET_REF_CLK1                    0x0008 0x0038 0x0564 0x2 0x3
+#define MX7D_PAD_GPIO1_IO02__SAI2_MCLK                            0x0008 0x0038 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO02__CCM_CLKO1                            0x0008 0x0038 0x0000 0x5 0x0
+#define MX7D_PAD_GPIO1_IO02__OBSERVE1_OUT                         0x0008 0x0038 0x0000 0x6 0x0
+#define MX7D_PAD_GPIO1_IO02__USB_OTG1_ID                          0x0008 0x0038 0x0734 0x7 0x3
+#define MX7D_PAD_GPIO1_IO03__GPIO1_IO3                            0x000C 0x003C 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO03__PWM3_OUT                             0x000C 0x003C 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO03__CCM_ENET_REF_CLK2                    0x000C 0x003C 0x0570 0x2 0x3
+#define MX7D_PAD_GPIO1_IO03__SAI3_MCLK                            0x000C 0x003C 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO03__CCM_CLKO2                            0x000C 0x003C 0x0000 0x5 0x0
+#define MX7D_PAD_GPIO1_IO03__OBSERVE2_OUT                         0x000C 0x003C 0x0000 0x6 0x0
+#define MX7D_PAD_GPIO1_IO03__USB_OTG2_ID                          0x000C 0x003C 0x0730 0x7 0x3
+#define MX7D_PAD_GPIO1_IO04__GPIO1_IO4                            0x0010 0x0040 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO04__USB_OTG1_OC                          0x0010 0x0040 0x072C 0x1 0x1
+#define MX7D_PAD_GPIO1_IO04__FLEXTIMER1_CH4                       0x0010 0x0040 0x0594 0x2 0x1
+#define MX7D_PAD_GPIO1_IO04__UART5_CTS_B                          0x0010 0x0040 0x0710 0x3 0x4
+#define MX7D_PAD_GPIO1_IO04__I2C1_SCL                             0x0010 0x0040 0x05D4 0x4 0x2
+#define MX7D_PAD_GPIO1_IO04__OBSERVE3_OUT                         0x0010 0x0040 0x0000 0x6 0x0
+#define MX7D_PAD_GPIO1_IO05__GPIO1_IO5                            0x0014 0x0044 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR                         0x0014 0x0044 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO05__FLEXTIMER1_CH5                       0x0014 0x0044 0x0598 0x2 0x1
+#define MX7D_PAD_GPIO1_IO05__UART5_RTS_B                          0x0014 0x0044 0x0710 0x3 0x5
+#define MX7D_PAD_GPIO1_IO05__I2C1_SDA                             0x0014 0x0044 0x05D8 0x4 0x2
+#define MX7D_PAD_GPIO1_IO05__OBSERVE4_OUT                         0x0014 0x0044 0x0000 0x6 0x0
+#define MX7D_PAD_GPIO1_IO06__GPIO1_IO6                            0x0018 0x0048 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO06__USB_OTG2_OC                          0x0018 0x0048 0x0728 0x1 0x1
+#define MX7D_PAD_GPIO1_IO06__FLEXTIMER1_CH6                       0x0018 0x0048 0x059C 0x2 0x1
+#define MX7D_PAD_GPIO1_IO06__UART5_RX_DATA                        0x0018 0x0048 0x0714 0x3 0x4
+#define MX7D_PAD_GPIO1_IO06__I2C2_SCL                             0x0018 0x0048 0x05DC 0x4 0x2
+#define MX7D_PAD_GPIO1_IO06__CCM_WAIT                             0x0018 0x0048 0x0000 0x5 0x0
+#define MX7D_PAD_GPIO1_IO06__KPP_ROW4                             0x0018 0x0048 0x0624 0x6 0x1
+#define MX7D_PAD_GPIO1_IO07__GPIO1_IO7                            0x001C 0x004C 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO07__USB_OTG2_PWR                         0x001C 0x004C 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO07__FLEXTIMER1_CH7                       0x001C 0x004C 0x05A0 0x2 0x1
+#define MX7D_PAD_GPIO1_IO07__UART5_TX_DATA                        0x001C 0x004C 0x0714 0x3 0x5
+#define MX7D_PAD_GPIO1_IO07__I2C2_SDA                             0x001C 0x004C 0x05E0 0x4 0x2
+#define MX7D_PAD_GPIO1_IO07__CCM_STOP                             0x001C 0x004C 0x0000 0x5 0x0
+#define MX7D_PAD_GPIO1_IO07__KPP_COL4                             0x001C 0x004C 0x0604 0x6 0x1
+#define MX7D_PAD_GPIO1_IO08__GPIO1_IO8                            0x0014 0x026C 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO08__SD1_VSELECT                          0x0014 0x026C 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO08__WDOG1_WDOG_B                         0x0014 0x026C 0x0000 0x2 0x0
+#define MX7D_PAD_GPIO1_IO08__UART3_DCE_RX                         0x0014 0x026C 0x0704 0x3 0x0
+#define MX7D_PAD_GPIO1_IO08__UART3_DTE_TX                         0x0014 0x026C 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO08__I2C3_SCL                             0x0014 0x026C 0x05E4 0x4 0x0
+#define MX7D_PAD_GPIO1_IO08__KPP_COL5                             0x0014 0x026C 0x0608 0x6 0x0
+#define MX7D_PAD_GPIO1_IO08__PWM1_OUT                             0x0014 0x026C 0x0000 0x7 0x0
+#define MX7D_PAD_GPIO1_IO09__GPIO1_IO9                            0x0018 0x0270 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO09__SD1_LCTL                             0x0018 0x0270 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO09__CCM_ENET_REF_CLK3                    0x0018 0x0270 0x0000 0x2 0x0
+#define MX7D_PAD_GPIO1_IO09__UART3_DCE_TX                         0x0018 0x0270 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO09__UART3_DTE_RX                         0x0018 0x0270 0x0704 0x3 0x1
+#define MX7D_PAD_GPIO1_IO09__I2C3_SDA                             0x0018 0x0270 0x05E8 0x4 0x0
+#define MX7D_PAD_GPIO1_IO09__CCM_PMIC_READY                       0x0018 0x0270 0x04F4 0x5 0x0
+#define MX7D_PAD_GPIO1_IO09__KPP_ROW5                             0x0018 0x0270 0x0628 0x6 0x0
+#define MX7D_PAD_GPIO1_IO09__PWM2_OUT                             0x0018 0x0270 0x0000 0x7 0x0
+#define MX7D_PAD_GPIO1_IO10__GPIO1_IO10                           0x001C 0x0274 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO10__SD2_LCTL                             0x001C 0x0274 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO10__ENET1_MDIO                           0x001C 0x0274 0x0568 0x2 0x0
+#define MX7D_PAD_GPIO1_IO10__UART3_DCE_RTS                        0x001C 0x0274 0x0700 0x3 0x0
+#define MX7D_PAD_GPIO1_IO10__UART3_DTE_CTS                        0x001C 0x0274 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO10__I2C4_SCL                             0x001C 0x0274 0x05EC 0x4 0x0
+#define MX7D_PAD_GPIO1_IO10__FLEXTIMER1_PHA                       0x001C 0x0274 0x05A4 0x5 0x0
+#define MX7D_PAD_GPIO1_IO10__KPP_COL6                             0x001C 0x0274 0x060C 0x6 0x0
+#define MX7D_PAD_GPIO1_IO10__PWM3_OUT                             0x001C 0x0274 0x0000 0x7 0x0
+#define MX7D_PAD_GPIO1_IO11__GPIO1_IO11                           0x0020 0x0278 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO11__SD3_LCTL                             0x0020 0x0278 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO11__ENET1_MDC                            0x0020 0x0278 0x0000 0x2 0x0
+#define MX7D_PAD_GPIO1_IO11__UART3_DCE_CTS                        0x0020 0x0278 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO11__UART3_DTE_RTS                        0x0020 0x0278 0x0700 0x3 0x1
+#define MX7D_PAD_GPIO1_IO11__I2C4_SDA                             0x0020 0x0278 0x05F0 0x4 0x0
+#define MX7D_PAD_GPIO1_IO11__FLEXTIMER1_PHB                       0x0020 0x0278 0x05A8 0x5 0x0
+#define MX7D_PAD_GPIO1_IO11__KPP_ROW6                             0x0020 0x0278 0x062C 0x6 0x0
+#define MX7D_PAD_GPIO1_IO11__PWM4_OUT                             0x0020 0x0278 0x0000 0x7 0x0
+#define MX7D_PAD_GPIO1_IO12__GPIO1_IO12                           0x0024 0x027C 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO12__SD2_VSELECT                          0x0024 0x027C 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1                    0x0024 0x027C 0x0564 0x2 0x0
+#define MX7D_PAD_GPIO1_IO12__FLEXCAN1_RX                          0x0024 0x027C 0x04DC 0x3 0x0
+#define MX7D_PAD_GPIO1_IO12__CM4_NMI                              0x0024 0x027C 0x0000 0x4 0x0
+#define MX7D_PAD_GPIO1_IO12__CCM_EXT_CLK1                         0x0024 0x027C 0x04E4 0x5 0x0
+#define MX7D_PAD_GPIO1_IO12__SNVS_VIO_5                           0x0024 0x027C 0x0000 0x6 0x0
+#define MX7D_PAD_GPIO1_IO12__USB_OTG1_ID                          0x0024 0x027C 0x0734 0x7 0x0
+#define MX7D_PAD_GPIO1_IO13__GPIO1_IO13                           0x0028 0x0280 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO13__SD3_VSELECT                          0x0028 0x0280 0x0000 0x1 0x0
+#define MX7D_PAD_GPIO1_IO13__CCM_ENET_REF_CLK2                    0x0028 0x0280 0x0570 0x2 0x0
+#define MX7D_PAD_GPIO1_IO13__FLEXCAN1_TX                          0x0028 0x0280 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO13__CCM_PMIC_READY                       0x0028 0x0280 0x04F4 0x4 0x1
+#define MX7D_PAD_GPIO1_IO13__CCM_EXT_CLK2                         0x0028 0x0280 0x04E8 0x5 0x0
+#define MX7D_PAD_GPIO1_IO13__SNVS_VIO_5_CTL                       0x0028 0x0280 0x0000 0x6 0x0
+#define MX7D_PAD_GPIO1_IO13__USB_OTG2_ID                          0x0028 0x0280 0x0730 0x7 0x0
+#define MX7D_PAD_GPIO1_IO14__GPIO1_IO14                           0x002C 0x0284 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO14__SD3_CD_B                             0x002C 0x0284 0x0738 0x1 0x0
+#define MX7D_PAD_GPIO1_IO14__ENET2_MDIO                           0x002C 0x0284 0x0574 0x2 0x0
+#define MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX                          0x002C 0x0284 0x04E0 0x3 0x0
+#define MX7D_PAD_GPIO1_IO14__WDOG3_WDOG_B                         0x002C 0x0284 0x0000 0x4 0x0
+#define MX7D_PAD_GPIO1_IO14__CCM_EXT_CLK3                         0x002C 0x0284 0x04EC 0x5 0x0
+#define MX7D_PAD_GPIO1_IO14__SDMA_EXT_EVENT0                      0x002C 0x0284 0x06D8 0x6 0x0
+#define MX7D_PAD_GPIO1_IO15__GPIO1_IO15                           0x0030 0x0288 0x0000 0x0 0x0
+#define MX7D_PAD_GPIO1_IO15__SD3_WP                               0x0030 0x0288 0x073C 0x1 0x0
+#define MX7D_PAD_GPIO1_IO15__ENET2_MDC                            0x0030 0x0288 0x0000 0x2 0x0
+#define MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX                          0x0030 0x0288 0x0000 0x3 0x0
+#define MX7D_PAD_GPIO1_IO15__WDOG4_WDOG_B                         0x0030 0x0288 0x0000 0x4 0x0
+#define MX7D_PAD_GPIO1_IO15__CCM_EXT_CLK4                         0x0030 0x0288 0x04F0 0x5 0x0
+#define MX7D_PAD_GPIO1_IO15__SDMA_EXT_EVENT1                      0x0030 0x0288 0x06DC 0x6 0x0
 #define MX7D_PAD_EPDC_DATA00__EPDC_DATA0                          0x0034 0x02A4 0x0000 0x0 0x0
 #define MX7D_PAD_EPDC_DATA00__SIM1_PORT2_TRXD                     0x0034 0x02A4 0x0000 0x1 0x0
 #define MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0                        0x0034 0x02A4 0x0000 0x2 0x0
@@ -453,7 +569,7 @@
 #define MX7D_PAD_LCD_DATA23__EIM_ADDR26                           0x0124 0x0394 0x0000 0x4 0x0
 #define MX7D_PAD_LCD_DATA23__GPIO3_IO28                           0x0124 0x0394 0x0000 0x5 0x0
 #define MX7D_PAD_LCD_DATA23__I2C4_SDA                             0x0124 0x0394 0x05F0 0x6 0x1
-#define MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX                      0x0128 0x0398 0x0000 0x0 0x0
+#define MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX                      0x0128 0x0398 0x06F4 0x0 0x0
 #define MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX                      0x0128 0x0398 0x0000 0x0 0x0
 #define MX7D_PAD_UART1_RX_DATA__I2C1_SCL                          0x0128 0x0398 0x05D4 0x1 0x0
 #define MX7D_PAD_UART1_RX_DATA__CCM_PMIC_READY                    0x0128 0x0398 0x0000 0x2 0x0
@@ -469,7 +585,7 @@
 #define MX7D_PAD_UART1_TX_DATA__ENET2_1588_EVENT0_OUT             0x012C 0x039C 0x0000 0x4 0x0
 #define MX7D_PAD_UART1_TX_DATA__GPIO4_IO1                         0x012C 0x039C 0x0000 0x5 0x0
 #define MX7D_PAD_UART1_TX_DATA__ENET1_MDC                         0x012C 0x039C 0x0000 0x6 0x0
-#define MX7D_PAD_UART2_RX_DATA__UART2_DCE_RX                      0x0130 0x03A0 0x0000 0x0 0x0
+#define MX7D_PAD_UART2_RX_DATA__UART2_DCE_RX                      0x0130 0x03A0 0x06FC 0x0 0x2
 #define MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX                      0x0130 0x03A0 0x0000 0x0 0x0
 #define MX7D_PAD_UART2_RX_DATA__I2C2_SCL                          0x0130 0x03A0 0x05DC 0x1 0x0
 #define MX7D_PAD_UART2_RX_DATA__SAI3_RX_BCLK                      0x0130 0x03A0 0x0000 0x2 0x0
@@ -501,7 +617,7 @@
 #define MX7D_PAD_UART3_TX_DATA__ENET1_1588_EVENT0_OUT             0x013C 0x03AC 0x0000 0x4 0x0
 #define MX7D_PAD_UART3_TX_DATA__GPIO4_IO5                         0x013C 0x03AC 0x0000 0x5 0x0
 #define MX7D_PAD_UART3_TX_DATA__SD2_LCTL                          0x013C 0x03AC 0x0000 0x6 0x0
-#define MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS                       0x0140 0x03B0 0x0000 0x0 0x0
+#define MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS                       0x0140 0x03B0 0x0700 0x0 0x2
 #define MX7D_PAD_UART3_RTS_B__UART3_DTE_CTS                       0x0140 0x03B0 0x0000 0x0 0x0
 #define MX7D_PAD_UART3_RTS_B__USB_OTG2_OC                         0x0140 0x03B0 0x0728 0x1 0x0
 #define MX7D_PAD_UART3_RTS_B__SAI3_TX_DATA0                       0x0140 0x03B0 0x0000 0x2 0x0
-- 
2.1.4

Re: [PATCH v4 2/8] ARM: imx: imx7d-pinfunc: add gpio1 pad iomux settings

[Shawn Guo]

On Fri, Sep 18, 2015 at 11:29:52AM -0500, Adrian Alonso wrote:
> - Add imx7 SoC GPIO1 pad iomuxc settings
>   <mux_reg conf_reg input_reg mux_mode input_val>
> - Fix UART input select daisy chain setting values
> 
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>

Applied this one, thanks.

[PATCH v4 3/8] ARM: dts: imx: imx7d add iomuxc lpsr device node

[Adrian Alonso]

Add device tree node to support iomuxc-lpsr controller, iput-sel phandle
allows to get input select register base address which is shared from
iomuxc controller.

Signed-off-by: Adrian Alonso <aalonso-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
Changes for V2: Resend
Changes for V3: Add phandle to get input select register base address
Changes for V4: Resend

 arch/arm/boot/dts/imx7d.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
index 15c2193..0cd7033 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -446,6 +446,12 @@
 				status = "disabled";
 			};
 
+			iomuxc_lpsr: iomuxc-lpsr@302c0000 {
+				compatible = "fsl,imx7d-iomuxc-lpsr";
+				reg = <0x302c0000 0x10000>;
+				input-sel = <&iomuxc>;
+			};
+
 			gpt1: gpt@302d0000 {
 				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
 				reg = <0x302d0000 0x10000>;
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 5/8] pinctrl: freescale: imx: add ZERO_OFFSET_VALID flag

[Adrian Alonso]

- Add ZERO_OFFSET_VALID flag, on imx7d mux_conf reg
  offset is zero for iomuxc-lspr controller
- Do default initialization on parse group function.

Signed-off-by: Adrian Alonso <aalonso-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
Changes for V2: Resend
Changes for V3: Resend
Changes for V4: Simplify pin_id assigment when ZERO_OFFSET_VALID is set

 drivers/pinctrl/freescale/pinctrl-imx.c | 20 ++++++++++----------
 drivers/pinctrl/freescale/pinctrl-imx.h |  1 +
 2 files changed, 11 insertions(+), 10 deletions(-)

diff --git a/drivers/pinctrl/freescale/pinctrl-imx.c b/drivers/pinctrl/freescale/pinctrl-imx.c
index b9c6deb..866d864 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.c
+++ b/drivers/pinctrl/freescale/pinctrl-imx.c
@@ -437,7 +437,7 @@ static void imx_pinconf_dbg_show(struct pinctrl_dev *pctldev,
 	const struct imx_pin_reg *pin_reg = &info->pin_regs[pin_id];
 	unsigned long config;
 
-	if (!pin_reg || pin_reg->conf_reg == -1) {
+	if (pin_reg->conf_reg == -1) {
 		seq_printf(s, "N/A");
 		return;
 	}
@@ -536,21 +536,26 @@ static int imx_pinctrl_parse_groups(struct device_node *np,
 		return -ENOMEM;
 
 	for (i = 0; i < grp->npins; i++) {
-		u32 mux_reg = be32_to_cpu(*list++);
+		u32 mux_reg;
 		u32 conf_reg;
 		unsigned int pin_id;
 		struct imx_pin_reg *pin_reg;
 		struct imx_pin *pin = &grp->pins[i];
 
+		mux_reg = be32_to_cpu(*list++);
+		if (!(info->flags & ZERO_OFFSET_VALID) && !mux_reg)
+			mux_reg = -1;
+
 		if (info->flags & SHARE_MUX_CONF_REG) {
 			conf_reg = mux_reg;
 		} else {
 			conf_reg = be32_to_cpu(*list++);
-			if (!conf_reg)
+			if (!(info->flags & ZERO_OFFSET_VALID) && !conf_reg)
 				conf_reg = -1;
 		}
 
-		pin_id = mux_reg ? mux_reg / 4 : conf_reg / 4;
+		pin_id = (mux_reg != -1) ? mux_reg / 4 : conf_reg / 4;
+
 		pin_reg = &info->pin_regs[pin_id];
 		pin->pin = pin_id;
 		grp->pin_ids[i] = pin_id;
@@ -684,7 +689,7 @@ int imx_pinctrl_probe(struct platform_device *pdev,
 {
 	struct imx_pinctrl *ipctl;
 	struct resource *res;
-	int ret, i;
+	int ret;
 
 	if (!info || !info->pins || !info->npins) {
 		dev_err(&pdev->dev, "wrong pinctrl info\n");
@@ -702,11 +707,6 @@ int imx_pinctrl_probe(struct platform_device *pdev,
 	if (!info->pin_regs)
 		return -ENOMEM;
 
-	for (i = 0; i < info->npins; i++) {
-		info->pin_regs[i].mux_reg = -1;
-		info->pin_regs[i].conf_reg = -1;
-	}
-
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	ipctl->base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(ipctl->base))
diff --git a/drivers/pinctrl/freescale/pinctrl-imx.h b/drivers/pinctrl/freescale/pinctrl-imx.h
index 2a5fe72..2a592f6 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.h
+++ b/drivers/pinctrl/freescale/pinctrl-imx.h
@@ -85,6 +85,7 @@ struct imx_pinctrl_soc_info {
 };
 
 #define SHARE_MUX_CONF_REG	0x1
+#define ZERO_OFFSET_VALID	0x2
 
 #define NO_MUX		0x0
 #define NO_PAD		0x0
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v4 5/8] pinctrl: freescale: imx: add ZERO_OFFSET_VALID flag

[Shawn Guo]

On Fri, Sep 18, 2015 at 11:29:55AM -0500, Adrian Alonso wrote:
> - Add ZERO_OFFSET_VALID flag, on imx7d mux_conf reg
>   offset is zero for iomuxc-lspr controller
> - Do default initialization on parse group function.
> 
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
> ---
> Changes for V2: Resend
> Changes for V3: Resend
> Changes for V4: Simplify pin_id assigment when ZERO_OFFSET_VALID is set
> 
>  drivers/pinctrl/freescale/pinctrl-imx.c | 20 ++++++++++----------
>  drivers/pinctrl/freescale/pinctrl-imx.h |  1 +
>  2 files changed, 11 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/pinctrl/freescale/pinctrl-imx.c b/drivers/pinctrl/freescale/pinctrl-imx.c
> index b9c6deb..866d864 100644
> --- a/drivers/pinctrl/freescale/pinctrl-imx.c
> +++ b/drivers/pinctrl/freescale/pinctrl-imx.c
> @@ -437,7 +437,7 @@ static void imx_pinconf_dbg_show(struct pinctrl_dev *pctldev,
>  	const struct imx_pin_reg *pin_reg = &info->pin_regs[pin_id];
>  	unsigned long config;
>  
> -	if (!pin_reg || pin_reg->conf_reg == -1) {
> +	if (pin_reg->conf_reg == -1) {
>  		seq_printf(s, "N/A");
>  		return;
>  	}
> @@ -536,21 +536,26 @@ static int imx_pinctrl_parse_groups(struct device_node *np,
>  		return -ENOMEM;
>  
>  	for (i = 0; i < grp->npins; i++) {
> -		u32 mux_reg = be32_to_cpu(*list++);
> +		u32 mux_reg;
>  		u32 conf_reg;
>  		unsigned int pin_id;
>  		struct imx_pin_reg *pin_reg;
>  		struct imx_pin *pin = &grp->pins[i];
>  
> +		mux_reg = be32_to_cpu(*list++);
> +		if (!(info->flags & ZERO_OFFSET_VALID) && !mux_reg)
> +			mux_reg = -1;
> +
>  		if (info->flags & SHARE_MUX_CONF_REG) {
>  			conf_reg = mux_reg;
>  		} else {
>  			conf_reg = be32_to_cpu(*list++);
> -			if (!conf_reg)
> +			if (!(info->flags & ZERO_OFFSET_VALID) && !conf_reg)
>  				conf_reg = -1;
>  		}
>  
> -		pin_id = mux_reg ? mux_reg / 4 : conf_reg / 4;
> +		pin_id = (mux_reg != -1) ? mux_reg / 4 : conf_reg / 4;
> +

This is the only meaningful change to me.  I do not understand why any
other changes in this patch is necessary.

>  		pin_reg = &info->pin_regs[pin_id];
>  		pin->pin = pin_id;
>  		grp->pin_ids[i] = pin_id;
> @@ -684,7 +689,7 @@ int imx_pinctrl_probe(struct platform_device *pdev,
>  {
>  	struct imx_pinctrl *ipctl;
>  	struct resource *res;
> -	int ret, i;
> +	int ret;
>  
>  	if (!info || !info->pins || !info->npins) {
>  		dev_err(&pdev->dev, "wrong pinctrl info\n");
> @@ -702,11 +707,6 @@ int imx_pinctrl_probe(struct platform_device *pdev,
>  	if (!info->pin_regs)
>  		return -ENOMEM;
>  
> -	for (i = 0; i < info->npins; i++) {
> -		info->pin_regs[i].mux_reg = -1;
> -		info->pin_regs[i].conf_reg = -1;
> -	}
> -
>  	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	ipctl->base = devm_ioremap_resource(&pdev->dev, res);
>  	if (IS_ERR(ipctl->base))
> diff --git a/drivers/pinctrl/freescale/pinctrl-imx.h b/drivers/pinctrl/freescale/pinctrl-imx.h
> index 2a5fe72..2a592f6 100644
> --- a/drivers/pinctrl/freescale/pinctrl-imx.h
> +++ b/drivers/pinctrl/freescale/pinctrl-imx.h
> @@ -85,6 +85,7 @@ struct imx_pinctrl_soc_info {
>  };
>  
>  #define SHARE_MUX_CONF_REG	0x1
> +#define ZERO_OFFSET_VALID	0x2
>  
>  #define NO_MUX		0x0
>  #define NO_PAD		0x0
> -- 
> 2.1.4
> 

[PATCH v4 4/8] ARM: dts: imx: imx7d-sbd add iomuxc-lpsr hoggrp-2 pads

[Adrian Alonso]

Add imx7d-sdb iomuxc-lpsr hoggrp-2 default pads settings

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: Resend
Changes for V3: Resend
Changes for V4: Resend

 arch/arm/boot/dts/imx7d-sdb.dts | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 8059458..c8a178c 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -419,3 +419,18 @@
 
 	};
 };
+
+&iomuxc_lpsr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_2>;
+
+	imx7d-sdb {
+		pinctrl_hog_2: hoggrp-2 {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO05__GPIO1_IO5    0x14
+				MX7D_PAD_GPIO1_IO07__GPIO1_IO7    0x59
+				MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_B 0x74
+			>;
+		};
+	};
+};
-- 
2.1.4

Re: [PATCH v4 4/8] ARM: dts: imx: imx7d-sbd add iomuxc-lpsr hoggrp-2 pads

[Markus Pargmann]

[-- Attachment #1: Type: text/plain, Size: 1452 bytes --]

Hi,

On Fri, Sep 18, 2015 at 11:29:54AM -0500, Adrian Alonso wrote:
> Add imx7d-sdb iomuxc-lpsr hoggrp-2 default pads settings
> 
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
> ---
> Changes for V2: Resend
> Changes for V3: Resend
> Changes for V4: Resend
> 
>  arch/arm/boot/dts/imx7d-sdb.dts | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
> index 8059458..c8a178c 100644
> --- a/arch/arm/boot/dts/imx7d-sdb.dts
> +++ b/arch/arm/boot/dts/imx7d-sdb.dts
> @@ -419,3 +419,18 @@
>  
>  	};
>  };
> +
> +&iomuxc_lpsr {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog_2>;
> +
> +	imx7d-sdb {
> +		pinctrl_hog_2: hoggrp-2 {
> +			fsl,pins = <
> +				MX7D_PAD_GPIO1_IO05__GPIO1_IO5    0x14
> +				MX7D_PAD_GPIO1_IO07__GPIO1_IO7    0x59
> +				MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_B 0x74

I think this belong to the watchdog node.

Also some comments for the GPIOs may probably be nice to know what they
are for.

Regards,

Markus

> +			>;
> +		};
> +	};
> +};
> -- 
> 2.1.4
> 
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH v4 6/8] pinctrl: freescale: imx: add shared input select reg support

[Adrian Alonso]

- Add shared input select register support
- imx7d has two iomux controllers iomuxc and iomuxc-lpsr
  which share select_input register for daisy chain settings

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: Resend
Changes for V3:
- Use of_parse_phandle instead of of_get_child_by_name to get input select
  base register address
Changes for V4: Resend

 drivers/pinctrl/freescale/pinctrl-imx.c | 28 +++++++++++++++++++++++++++-
 drivers/pinctrl/freescale/pinctrl-imx.h |  1 +
 2 files changed, 28 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/freescale/pinctrl-imx.c b/drivers/pinctrl/freescale/pinctrl-imx.c
index 866d864..619915f 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.c
+++ b/drivers/pinctrl/freescale/pinctrl-imx.c
@@ -18,6 +18,7 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_address.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/pinctrl/pinconf.h>
 #include <linux/pinctrl/pinctrl.h>
@@ -39,6 +40,7 @@ struct imx_pinctrl {
 	struct device *dev;
 	struct pinctrl_dev *pctl;
 	void __iomem *base;
+	void __iomem *input_sel_base;
 	const struct imx_pinctrl_soc_info *info;
 };
 
@@ -254,7 +256,12 @@ static int imx_pmx_set(struct pinctrl_dev *pctldev, unsigned selector,
 			 * Regular select input register can never be at offset
 			 * 0, and we only print register value for regular case.
 			 */
-			writel(pin->input_val, ipctl->base + pin->input_reg);
+			if (info->flags & SHARE_INPUT_SELECT_REG)
+				writel(pin->input_val, ipctl->input_sel_base +
+						pin->input_reg);
+			else
+				writel(pin->input_val, ipctl->base +
+						pin->input_reg);
 			dev_dbg(ipctl->dev,
 				"==>select_input: offset 0x%x val 0x%x\n",
 				pin->input_reg, pin->input_val);
@@ -687,6 +694,8 @@ static int imx_pinctrl_probe_dt(struct platform_device *pdev,
 int imx_pinctrl_probe(struct platform_device *pdev,
 		      struct imx_pinctrl_soc_info *info)
 {
+	struct device_node *dev_np = pdev->dev.of_node;
+	struct device_node *np;
 	struct imx_pinctrl *ipctl;
 	struct resource *res;
 	int ret;
@@ -712,6 +721,23 @@ int imx_pinctrl_probe(struct platform_device *pdev,
 	if (IS_ERR(ipctl->base))
 		return PTR_ERR(ipctl->base);
 
+	if (info->flags & SHARE_INPUT_SELECT_REG) {
+		np = of_parse_phandle(dev_np, "input-sel", 0);
+		if (np) {
+			ipctl->input_sel_base = of_iomap(np, 0);
+			if (IS_ERR(ipctl->input_sel_base)) {
+				of_node_put(np);
+				dev_err(&pdev->dev,
+				       "iomuxc input select base address not found\n");
+				return PTR_ERR(ipctl->input_sel_base);
+			}
+		} else {
+			dev_err(&pdev->dev, "iomuxc input-sel device node not found\n");
+			return -EINVAL;
+		}
+		of_node_put(np);
+	}
+
 	imx_pinctrl_desc.name = dev_name(&pdev->dev);
 	imx_pinctrl_desc.pins = info->pins;
 	imx_pinctrl_desc.npins = info->npins;
diff --git a/drivers/pinctrl/freescale/pinctrl-imx.h b/drivers/pinctrl/freescale/pinctrl-imx.h
index 2a592f6..3805476 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx.h
+++ b/drivers/pinctrl/freescale/pinctrl-imx.h
@@ -86,6 +86,7 @@ struct imx_pinctrl_soc_info {
 
 #define SHARE_MUX_CONF_REG	0x1
 #define ZERO_OFFSET_VALID	0x2
+#define SHARE_INPUT_SELECT_REG	0x4
 
 #define NO_MUX		0x0
 #define NO_PAD		0x0
-- 
2.1.4

[PATCH v4 7/8] pinctrl: freescale: imx7d: support iomux lpsr controller

[Adrian Alonso]

iMX7D has two iomuxc controllers, iomuxc controller similar as
previous iMX SoC generation and iomuxc-lpsr which provides low
power state rentetion capabilities on gpios that are part of
iomuxc-lpsr

- Add iomuxc-lpsr gpio group id's
- Use flag ZERO_OFFSET_VALID and SHARE_INPUT_SELECT_REG to
  properly set pads from iomuxc-lpsr domain

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: Add imx7d_lpsr_pads enums
Changes for V3: Resend
Changes for V4: Resend

 drivers/pinctrl/freescale/pinctrl-imx7d.c | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/drivers/pinctrl/freescale/pinctrl-imx7d.c b/drivers/pinctrl/freescale/pinctrl-imx7d.c
index 1fa7530..b4d77e4 100644
--- a/drivers/pinctrl/freescale/pinctrl-imx7d.c
+++ b/drivers/pinctrl/freescale/pinctrl-imx7d.c
@@ -174,6 +174,17 @@ enum imx7d_pads {
 	MX7D_PAD_ENET1_COL = 154,
 };
 
+enum imx7d_lpsr_pads {
+	MX7D_PAD_GPIO1_IO00 = 0,
+	MX7D_PAD_GPIO1_IO01 = 1,
+	MX7D_PAD_GPIO1_IO02 = 2,
+	MX7D_PAD_GPIO1_IO03 = 3,
+	MX7D_PAD_GPIO1_IO04 = 4,
+	MX7D_PAD_GPIO1_IO05 = 5,
+	MX7D_PAD_GPIO1_IO06 = 6,
+	MX7D_PAD_GPIO1_IO07 = 7,
+};
+
 /* Pad names for the pinmux subsystem */
 static const struct pinctrl_pin_desc imx7d_pinctrl_pads[] = {
 	IMX_PINCTRL_PIN(MX7D_PAD_RESERVE0),
@@ -333,13 +344,32 @@ static const struct pinctrl_pin_desc imx7d_pinctrl_pads[] = {
 	IMX_PINCTRL_PIN(MX7D_PAD_ENET1_COL),
 };
 
+/* Pad names for the pinmux subsystem */
+static const struct pinctrl_pin_desc imx7d_lpsr_pinctrl_pads[] = {
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO00),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO01),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO02),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO03),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO04),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO05),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO06),
+	IMX_PINCTRL_PIN(MX7D_PAD_GPIO1_IO07),
+};
+
 static struct imx_pinctrl_soc_info imx7d_pinctrl_info = {
 	.pins = imx7d_pinctrl_pads,
 	.npins = ARRAY_SIZE(imx7d_pinctrl_pads),
 };
 
+static struct imx_pinctrl_soc_info imx7d_lpsr_pinctrl_info = {
+	.pins = imx7d_lpsr_pinctrl_pads,
+	.npins = ARRAY_SIZE(imx7d_lpsr_pinctrl_pads),
+	.flags = SHARE_INPUT_SELECT_REG | ZERO_OFFSET_VALID,
+};
+
 static struct of_device_id imx7d_pinctrl_of_match[] = {
 	{ .compatible = "fsl,imx7d-iomuxc", .data = &imx7d_pinctrl_info, },
+	{ .compatible = "fsl,imx7d-iomuxc-lpsr", .data = &imx7d_lpsr_pinctrl_info },
 	{ /* sentinel */ }
 };
 
-- 
2.1.4

[PATCH v4 8/8] pinctrl: freescale: imx: imx7d iomuxc-lpsr devicetree bindings

[Adrian Alonso]

Add iomuxc-lpsr devicetree bindings documentation
Provide documentation context as well an example on
pheriperals that could use pad from either iomuxc controller
supported by iMX7D SoC

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: New patch on imx7d iomuxc-lpsr patch series
Changes for V3: Add shared input select register notes
Changes for V4: Resend

 .../bindings/pinctrl/fsl,imx7d-pinctrl.txt         | 57 ++++++++++++++++++++++
 1 file changed, 57 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
index 8bbf25d..19697bd 100644
--- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
@@ -1,10 +1,33 @@
 * Freescale i.MX7 Dual IOMUX Controller
 
+iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar
+as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low
+power state rentetion capabilities on gpios that are part of iomuxc-lpsr
+(GPIO1_IO7..GPIO1_IO0). While iomuxc-lpsr provides its own set of registers for
+mux and pad control settings it shares the input select register from iomuxc
+for daisy chain settings, the input-sel phandle and SHARE_INPUT_SELECT_REG flag
+extends fsl,imx-pinctrl driver to support iomuxc-lpsr controller.
+
+iomuxc_lpsr: iomuxc-lpsr@302c0000 {
+	compatible = "fsl,imx7d-iomuxc-lpsr";
+	reg = <0x302c0000 0x10000>;
+	input-sel = <&iomuxc>;
+};
+
+iomuxc: iomuxc@30330000 {
+	compatible = "fsl,imx7d-iomuxc";
+	reg = <0x30330000 0x10000>;
+};
+
+Pheriparials using pads from iomuxc-lpsr support low state retention power
+state, under LPSR mode GPIO's state of pads are retain.
+
 Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
 and usage.
 
 Required properties:
 - compatible: "fsl,imx7d-iomuxc"
+- compatible: "fsl,imx7d-iomuxc-lpsr"
 - fsl,pins: each entry consists of 6 integers and represents the mux and config
   setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
   input_val> are specified using a PIN_FUNC_ID macro, which can be found in
@@ -25,3 +48,37 @@ PAD_CTL_DSE_X1                  (0 << 0)
 PAD_CTL_DSE_X2                  (1 << 0)
 PAD_CTL_DSE_X3                  (2 << 0)
 PAD_CTL_DSE_X4                  (3 << 0)
+
+Examples:
+While iomuxc-lpsr is intended to be used by dedicated peripherals to take
+advantages of LPSR power mode, is also possible that an IP to use pads from
+any of the iomux controllers. For example the I2C1 IP can use SCL pad from
+iomuxc-lpsr controller and SDA pad from iomuxc controller as:
+
+i2c1: i2c@30a20000 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>;
+	status = "okay";
+};
+
+iomuxc-lpsr@302c0000 {
+	compatible = "fsl,imx7d-iomuxc-lpsr";
+	reg = <0x302c0000 0x10000>;
+
+	pinctrl_i2c1_1: i2c1grp-1 {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f
+		>;
+	};
+};
+
+iomuxc@30330000 {
+	compatible = "fsl,imx7d-iomuxc";
+	reg = <0x30330000 0x10000>;
+
+	pinctrl_i2c1_2: i2c1grp-2 {
+		fsl,pins = <
+			MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f
+		>;
+	};
+};
-- 
2.1.4

Re: [PATCH v4 8/8] pinctrl: freescale: imx: imx7d iomuxc-lpsr devicetree bindings

[Shawn Guo]

On Fri, Sep 18, 2015 at 11:29:58AM -0500, Adrian Alonso wrote:
> Add iomuxc-lpsr devicetree bindings documentation
> Provide documentation context as well an example on
> pheriperals that could use pad from either iomuxc controller
> supported by iMX7D SoC
> 
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
> ---
> Changes for V2: New patch on imx7d iomuxc-lpsr patch series
> Changes for V3: Add shared input select register notes
> Changes for V4: Resend
> 
>  .../bindings/pinctrl/fsl,imx7d-pinctrl.txt         | 57 ++++++++++++++++++++++
>  1 file changed, 57 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
> index 8bbf25d..19697bd 100644
> --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
> @@ -1,10 +1,33 @@
>  * Freescale i.MX7 Dual IOMUX Controller
>  
> +iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar
> +as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low
> +power state rentetion capabilities on gpios that are part of iomuxc-lpsr

s/rentetion/retention

> +(GPIO1_IO7..GPIO1_IO0). While iomuxc-lpsr provides its own set of registers for
> +mux and pad control settings it shares the input select register from iomuxc
> +for daisy chain settings, the input-sel phandle and SHARE_INPUT_SELECT_REG flag

SHARE_INPUT_SELECT_REG is a Linux device driver implementation details,
which shouldn't be in bindings doc.

> +extends fsl,imx-pinctrl driver to support iomuxc-lpsr controller.
> +
> +iomuxc_lpsr: iomuxc-lpsr@302c0000 {
> +	compatible = "fsl,imx7d-iomuxc-lpsr";
> +	reg = <0x302c0000 0x10000>;
> +	input-sel = <&iomuxc>;
> +};
> +
> +iomuxc: iomuxc@30330000 {
> +	compatible = "fsl,imx7d-iomuxc";
> +	reg = <0x30330000 0x10000>;
> +};
> +
> +Pheriparials using pads from iomuxc-lpsr support low state retention power
> +state, under LPSR mode GPIO's state of pads are retain.
> +
>  Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
>  and usage.
>  
>  Required properties:
>  - compatible: "fsl,imx7d-iomuxc"
> +- compatible: "fsl,imx7d-iomuxc-lpsr"

This is a bit confusing, and should probably be reworded like:

   - compatible: "fsl,imx7d-iomuxc" for main IOMUXC controller, or
                 "fsl,imx7d-iomuxc-lpsr" for Low Power State Retention
                 IOMUXC controller.

And 'input-sel' should be documented in 'Required properties' list as
well.  Also, as this is a vendor specific property, I suggest you name
it 'fsl,input-sel'.

>  - fsl,pins: each entry consists of 6 integers and represents the mux and config
>    setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
>    input_val> are specified using a PIN_FUNC_ID macro, which can be found in
> @@ -25,3 +48,37 @@ PAD_CTL_DSE_X1                  (0 << 0)
>  PAD_CTL_DSE_X2                  (1 << 0)
>  PAD_CTL_DSE_X3                  (2 << 0)
>  PAD_CTL_DSE_X4                  (3 << 0)
> +
> +Examples:
> +While iomuxc-lpsr is intended to be used by dedicated peripherals to take
> +advantages of LPSR power mode, is also possible that an IP to use pads from

s/is/it's ?

> +any of the iomux controllers. For example the I2C1 IP can use SCL pad from
> +iomuxc-lpsr controller and SDA pad from iomuxc controller as:
> +
> +i2c1: i2c@30a20000 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>;
> +	status = "okay";
> +};
> +
> +iomuxc-lpsr@302c0000 {
> +	compatible = "fsl,imx7d-iomuxc-lpsr";
> +	reg = <0x302c0000 0x10000>;
> +
> +	pinctrl_i2c1_1: i2c1grp-1 {
> +		fsl,pins = <
> +			MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f
> +		>;
> +	};
> +};
> +
> +iomuxc@30330000 {
> +	compatible = "fsl,imx7d-iomuxc";
> +	reg = <0x30330000 0x10000>;
> +
> +	pinctrl_i2c1_2: i2c1grp-2 {
> +		fsl,pins = <
> +			MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f

It's should be about 'SDA' pad than 'SCL', right?

Shawn

> +		>;
> +	};
> +};
> -- 
> 2.1.4
>