* [PATCH v6 1/9] Input: goodix - sort includes alphabetically
2015-09-15 14:31 [PATCH v6 0/9] Goodix touchscreen enhancements Irina Tirdea
@ 2015-09-15 14:31 ` Irina Tirdea
2015-09-15 14:31 ` [PATCH v6 2/9] Input: goodix - use actual config length for each device type Irina Tirdea
` (7 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree,
Irina Tirdea
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
---
drivers/input/touchscreen/goodix.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index e36162b..6ae28c5 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -14,18 +14,18 @@
* Software Foundation; version 2 of the License.
*/
-#include <linux/kernel.h>
+#include <linux/acpi.h>
+#include <linux/delay.h>
#include <linux/dmi.h>
#include <linux/i2c.h>
#include <linux/input.h>
#include <linux/input/mt.h>
-#include <linux/module.h>
-#include <linux/delay.h>
-#include <linux/irq.h>
#include <linux/interrupt.h>
-#include <linux/slab.h>
-#include <linux/acpi.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/of.h>
+#include <linux/slab.h>
#include <asm/unaligned.h>
struct goodix_ts_data {
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v6 2/9] Input: goodix - use actual config length for each device type
2015-09-15 14:31 [PATCH v6 0/9] Goodix touchscreen enhancements Irina Tirdea
2015-09-15 14:31 ` [PATCH v6 1/9] Input: goodix - sort includes alphabetically Irina Tirdea
@ 2015-09-15 14:31 ` Irina Tirdea
2015-09-15 14:31 ` [PATCH v6 3/9] Input: goodix - reset device at init Irina Tirdea
` (6 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree,
Irina Tirdea
Each of the Goodix devices supported by this driver has a fixed size for
the configuration information registers. The size varies depending on the
device and is specified in the datasheet.
Use the proper configuration length as specified in the datasheet for
each device model, so we do not read more than the actual size of the
configuration registers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
---
drivers/input/touchscreen/goodix.c | 25 +++++++++++++++++++++++--
1 file changed, 23 insertions(+), 2 deletions(-)
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 6ae28c5..7be6eab 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -36,6 +36,7 @@ struct goodix_ts_data {
unsigned int max_touch_num;
unsigned int int_trigger_type;
bool rotated_screen;
+ int cfg_len;
};
#define GOODIX_MAX_HEIGHT 4096
@@ -45,6 +46,8 @@ struct goodix_ts_data {
#define GOODIX_MAX_CONTACTS 10
#define GOODIX_CONFIG_MAX_LENGTH 240
+#define GOODIX_CONFIG_911_LENGTH 186
+#define GOODIX_CONFIG_967_LENGTH 228
/* Register defines */
#define GOODIX_READ_COOR_ADDR 0x814E
@@ -115,6 +118,23 @@ static int goodix_i2c_read(struct i2c_client *client,
return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0);
}
+static int goodix_get_cfg_len(u16 id)
+{
+ switch (id) {
+ case 911:
+ case 9271:
+ case 9110:
+ case 927:
+ case 928:
+ return GOODIX_CONFIG_911_LENGTH;
+ case 912:
+ case 967:
+ return GOODIX_CONFIG_967_LENGTH;
+ default:
+ return GOODIX_CONFIG_MAX_LENGTH;
+ }
+}
+
static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
{
int touch_num;
@@ -230,8 +250,7 @@ static void goodix_read_config(struct goodix_ts_data *ts)
int error;
error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
- config,
- GOODIX_CONFIG_MAX_LENGTH);
+ config, ts->cfg_len);
if (error) {
dev_warn(&ts->client->dev,
"Error reading config (%d), using defaults\n",
@@ -398,6 +417,8 @@ static int goodix_ts_probe(struct i2c_client *client,
return error;
}
+ ts->cfg_len = goodix_get_cfg_len(id_info);
+
goodix_read_config(ts);
error = goodix_request_input_dev(ts, version_info, id_info);
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v6 3/9] Input: goodix - reset device at init
2015-09-15 14:31 [PATCH v6 0/9] Goodix touchscreen enhancements Irina Tirdea
2015-09-15 14:31 ` [PATCH v6 1/9] Input: goodix - sort includes alphabetically Irina Tirdea
2015-09-15 14:31 ` [PATCH v6 2/9] Input: goodix - use actual config length for each device type Irina Tirdea
@ 2015-09-15 14:31 ` Irina Tirdea
2015-09-21 21:54 ` Aleksei Mamlin
2015-09-15 14:31 ` [PATCH v6 4/9] Input: goodix - write configuration data to device Irina Tirdea
` (5 subsequent siblings)
8 siblings, 1 reply; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree,
Irina Tirdea
After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins declared, the functionality depending
on these pins will not be available, but the device can still be used
with basic functionality.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
.../bindings/input/touchscreen/goodix.txt | 5 +
drivers/input/touchscreen/goodix.c | 136 +++++++++++++++++++++
2 files changed, 141 insertions(+)
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index 8ba98ee..c0715f8 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -12,6 +12,8 @@ Required properties:
- reg : I2C address of the chip. Should be 0x5d or 0x14
- interrupt-parent : Interrupt controller to which the chip is connected
- interrupts : Interrupt to which the chip is connected
+ - gpios : GPIOS the chip is connected to: first one is the
+ interrupt gpio and second one the reset gpio.
Example:
@@ -23,6 +25,9 @@ Example:
reg = <0x5d>;
interrupt-parent = <&gpio>;
interrupts = <0 0>;
+
+ gpios = <&gpio1 0 0>, /* INT */
+ <&gpio1 1 0>; /* RST */
};
/* ... */
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 7be6eab..9c58583 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -17,6 +17,7 @@
#include <linux/acpi.h>
#include <linux/delay.h>
#include <linux/dmi.h>
+#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/input.h>
#include <linux/input/mt.h>
@@ -37,6 +38,8 @@ struct goodix_ts_data {
unsigned int int_trigger_type;
bool rotated_screen;
int cfg_len;
+ struct gpio_desc *gpiod_int;
+ struct gpio_desc *gpiod_rst;
};
#define GOODIX_MAX_HEIGHT 4096
@@ -89,6 +92,30 @@ static const struct dmi_system_id rotated_screen[] = {
{}
};
+/*
+ * ACPI table specifies gpio pins in this order: first rst pin and
+ * then interrupt pin.
+ */
+static const struct dmi_system_id goodix_rst_pin_first[] = {
+#if defined(CONFIG_DMI) && defined(CONFIG_X86)
+ {
+ .ident = "WinBook TW100",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "WinBook"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TW100")
+ }
+ },
+ {
+ .ident = "WinBook TW700",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "WinBook"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TW700")
+ },
+ },
+#endif
+ {}
+};
+
/**
* goodix_i2c_read - read data from a register of the i2c slave device.
*
@@ -237,6 +264,102 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static int goodix_int_sync(struct goodix_ts_data *ts)
+{
+ int error;
+
+ error = gpiod_direction_output(ts->gpiod_int, 0);
+ if (error)
+ return error;
+ msleep(50); /* T5: 50ms */
+
+ return gpiod_direction_input(ts->gpiod_int);
+}
+
+/**
+ * goodix_reset - Reset device during power on
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_reset(struct goodix_ts_data *ts)
+{
+ int error;
+
+ /* begin select I2C slave addr */
+ error = gpiod_direction_output(ts->gpiod_rst, 0);
+ if (error)
+ return error;
+ msleep(20); /* T2: > 10ms */
+ /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
+ error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
+ if (error)
+ return error;
+ usleep_range(100, 2000); /* T3: > 100us */
+ error = gpiod_direction_output(ts->gpiod_rst, 1);
+ if (error)
+ return error;
+ usleep_range(6000, 10000); /* T4: > 5ms */
+ /* end select I2C slave addr */
+ error = gpiod_direction_input(ts->gpiod_rst);
+ if (error)
+ return error;
+ return goodix_int_sync(ts);
+}
+
+/**
+ * goodix_get_gpio_config - Get GPIO config from ACPI/DT
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_get_gpio_config(struct goodix_ts_data *ts,
+ const struct i2c_device_id *i2c_id)
+{
+ int error;
+ struct device *dev;
+ struct gpio_desc *gpiod;
+ /* Default gpio pin order: irq, rst */
+ int irq_idx = 0, rst_idx = 1;
+
+ if (!ts->client)
+ return -EINVAL;
+ dev = &ts->client->dev;
+
+ if (dmi_check_system(goodix_rst_pin_first)) {
+ dev_dbg(&ts->client->dev,
+ "Applying 'reverse gpio pin order' quirk\n");
+ rst_idx = 0;
+ irq_idx = 1;
+ }
+
+ /* Get interrupt GPIO pin number */
+ gpiod = devm_gpiod_get_index(dev, NULL, irq_idx, GPIOD_IN);
+ if (IS_ERR(gpiod)) {
+ error = PTR_ERR(gpiod);
+ if (error != -EPROBE_DEFER)
+ dev_warn(dev, "Failed to get GPIO %d: %d\n",
+ irq_idx, error);
+ if (error == -ENOENT)
+ return 0;
+ return error;
+ }
+ ts->gpiod_int = gpiod;
+
+ /* Get the reset line GPIO pin number */
+ gpiod = devm_gpiod_get_index(dev, NULL, rst_idx, GPIOD_IN);
+ if (IS_ERR(gpiod)) {
+ error = PTR_ERR(gpiod);
+ if (error != -EPROBE_DEFER)
+ dev_warn(dev, "Failed to get GPIO %d: %d\n",
+ rst_idx, error);
+ if (error == -ENOENT)
+ return 0;
+ return error;
+ }
+ ts->gpiod_rst = gpiod;
+
+ return 0;
+}
+
/**
* goodix_read_config - Read the embedded configuration of the panel
*
@@ -405,6 +528,19 @@ static int goodix_ts_probe(struct i2c_client *client,
ts->client = client;
i2c_set_clientdata(client, ts);
+ error = goodix_get_gpio_config(ts, id);
+ if (error)
+ return error;
+
+ if (ts->gpiod_int && ts->gpiod_rst) {
+ /* reset the controller */
+ error = goodix_reset(ts);
+ if (error) {
+ dev_err(&client->dev, "Controller reset failed.\n");
+ return error;
+ }
+ }
+
error = goodix_i2c_test(client);
if (error) {
dev_err(&client->dev, "I2C communication failure: %d\n", error);
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v6 3/9] Input: goodix - reset device at init
2015-09-15 14:31 ` [PATCH v6 3/9] Input: goodix - reset device at init Irina Tirdea
@ 2015-09-21 21:54 ` Aleksei Mamlin
0 siblings, 0 replies; 13+ messages in thread
From: Aleksei Mamlin @ 2015-09-21 21:54 UTC (permalink / raw)
To: Irina Tirdea
Cc: Dmitry Torokhov, Bastien Nocera, linux-input, Mark Rutland,
Octavian Purdila, linux-kernel, devicetree
On Tue, 15 Sep 2015 17:31:17 +0300
Irina Tirdea <irina.tirdea@intel.com> wrote:
> After power on, it is recommended that the driver resets the device.
> The reset procedure timing is described in the datasheet and is used
> at device init (before writing device configuration) and
> for power management. It is a sequence of setting the interrupt
> and reset pins high/low at specific timing intervals. This procedure
> also includes setting the slave address to the one specified in the
> ACPI/device tree.
>
> This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
> driver gt9xx.c for Android (publicly available in Android kernel
> trees for various devices).
>
> For reset the driver needs to control the interrupt and
> reset gpio pins (configured through ACPI/device tree). For devices
> that do not have the gpio pins declared, the functionality depending
> on these pins will not be available, but the device can still be used
> with basic functionality.
>
I tested this patch on ARM tablet Wexler TAB7200 with GT911 touchscreen
controller. All works fine.
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
>
> Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
> Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
> ---
> .../bindings/input/touchscreen/goodix.txt | 5 +
> drivers/input/touchscreen/goodix.c | 136 +++++++++++++++++++++
> 2 files changed, 141 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> index 8ba98ee..c0715f8 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> @@ -12,6 +12,8 @@ Required properties:
> - reg : I2C address of the chip. Should be 0x5d or 0x14
> - interrupt-parent : Interrupt controller to which the chip is connected
> - interrupts : Interrupt to which the chip is connected
> + - gpios : GPIOS the chip is connected to: first one is the
> + interrupt gpio and second one the reset gpio.
>
> Example:
>
> @@ -23,6 +25,9 @@ Example:
> reg = <0x5d>;
> interrupt-parent = <&gpio>;
> interrupts = <0 0>;
> +
> + gpios = <&gpio1 0 0>, /* INT */
> + <&gpio1 1 0>; /* RST */
> };
>
> /* ... */
> diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
> index 7be6eab..9c58583 100644
> --- a/drivers/input/touchscreen/goodix.c
> +++ b/drivers/input/touchscreen/goodix.c
> @@ -17,6 +17,7 @@
> #include <linux/acpi.h>
> #include <linux/delay.h>
> #include <linux/dmi.h>
> +#include <linux/gpio.h>
> #include <linux/i2c.h>
> #include <linux/input.h>
> #include <linux/input/mt.h>
> @@ -37,6 +38,8 @@ struct goodix_ts_data {
> unsigned int int_trigger_type;
> bool rotated_screen;
> int cfg_len;
> + struct gpio_desc *gpiod_int;
> + struct gpio_desc *gpiod_rst;
> };
>
> #define GOODIX_MAX_HEIGHT 4096
> @@ -89,6 +92,30 @@ static const struct dmi_system_id rotated_screen[] = {
> {}
> };
>
> +/*
> + * ACPI table specifies gpio pins in this order: first rst pin and
> + * then interrupt pin.
> + */
> +static const struct dmi_system_id goodix_rst_pin_first[] = {
> +#if defined(CONFIG_DMI) && defined(CONFIG_X86)
> + {
> + .ident = "WinBook TW100",
> + .matches = {
> + DMI_MATCH(DMI_SYS_VENDOR, "WinBook"),
> + DMI_MATCH(DMI_PRODUCT_NAME, "TW100")
> + }
> + },
> + {
> + .ident = "WinBook TW700",
> + .matches = {
> + DMI_MATCH(DMI_SYS_VENDOR, "WinBook"),
> + DMI_MATCH(DMI_PRODUCT_NAME, "TW700")
> + },
> + },
> +#endif
> + {}
> +};
> +
> /**
> * goodix_i2c_read - read data from a register of the i2c slave device.
> *
> @@ -237,6 +264,102 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
> return IRQ_HANDLED;
> }
>
> +static int goodix_int_sync(struct goodix_ts_data *ts)
> +{
> + int error;
> +
> + error = gpiod_direction_output(ts->gpiod_int, 0);
> + if (error)
> + return error;
> + msleep(50); /* T5: 50ms */
> +
> + return gpiod_direction_input(ts->gpiod_int);
> +}
> +
> +/**
> + * goodix_reset - Reset device during power on
> + *
> + * @ts: goodix_ts_data pointer
> + */
> +static int goodix_reset(struct goodix_ts_data *ts)
> +{
> + int error;
> +
> + /* begin select I2C slave addr */
> + error = gpiod_direction_output(ts->gpiod_rst, 0);
> + if (error)
> + return error;
> + msleep(20); /* T2: > 10ms */
> + /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
> + error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
> + if (error)
> + return error;
> + usleep_range(100, 2000); /* T3: > 100us */
> + error = gpiod_direction_output(ts->gpiod_rst, 1);
> + if (error)
> + return error;
> + usleep_range(6000, 10000); /* T4: > 5ms */
> + /* end select I2C slave addr */
> + error = gpiod_direction_input(ts->gpiod_rst);
> + if (error)
> + return error;
> + return goodix_int_sync(ts);
> +}
> +
> +/**
> + * goodix_get_gpio_config - Get GPIO config from ACPI/DT
> + *
> + * @ts: goodix_ts_data pointer
> + */
> +static int goodix_get_gpio_config(struct goodix_ts_data *ts,
> + const struct i2c_device_id *i2c_id)
> +{
> + int error;
> + struct device *dev;
> + struct gpio_desc *gpiod;
> + /* Default gpio pin order: irq, rst */
> + int irq_idx = 0, rst_idx = 1;
> +
> + if (!ts->client)
> + return -EINVAL;
> + dev = &ts->client->dev;
> +
> + if (dmi_check_system(goodix_rst_pin_first)) {
> + dev_dbg(&ts->client->dev,
> + "Applying 'reverse gpio pin order' quirk\n");
> + rst_idx = 0;
> + irq_idx = 1;
> + }
> +
> + /* Get interrupt GPIO pin number */
> + gpiod = devm_gpiod_get_index(dev, NULL, irq_idx, GPIOD_IN);
> + if (IS_ERR(gpiod)) {
> + error = PTR_ERR(gpiod);
> + if (error != -EPROBE_DEFER)
> + dev_warn(dev, "Failed to get GPIO %d: %d\n",
> + irq_idx, error);
> + if (error == -ENOENT)
> + return 0;
> + return error;
> + }
> + ts->gpiod_int = gpiod;
> +
> + /* Get the reset line GPIO pin number */
> + gpiod = devm_gpiod_get_index(dev, NULL, rst_idx, GPIOD_IN);
> + if (IS_ERR(gpiod)) {
> + error = PTR_ERR(gpiod);
> + if (error != -EPROBE_DEFER)
> + dev_warn(dev, "Failed to get GPIO %d: %d\n",
> + rst_idx, error);
> + if (error == -ENOENT)
> + return 0;
> + return error;
> + }
> + ts->gpiod_rst = gpiod;
> +
> + return 0;
> +}
> +
> /**
> * goodix_read_config - Read the embedded configuration of the panel
> *
> @@ -405,6 +528,19 @@ static int goodix_ts_probe(struct i2c_client *client,
> ts->client = client;
> i2c_set_clientdata(client, ts);
>
> + error = goodix_get_gpio_config(ts, id);
> + if (error)
> + return error;
> +
> + if (ts->gpiod_int && ts->gpiod_rst) {
> + /* reset the controller */
> + error = goodix_reset(ts);
> + if (error) {
> + dev_err(&client->dev, "Controller reset failed.\n");
> + return error;
> + }
> + }
> +
> error = goodix_i2c_test(client);
> if (error) {
> dev_err(&client->dev, "I2C communication failure: %d\n", error);
> --
> 1.9.1
>
--
Thanks and regards,
Aleksei Mamlin
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v6 4/9] Input: goodix - write configuration data to device
2015-09-15 14:31 [PATCH v6 0/9] Goodix touchscreen enhancements Irina Tirdea
` (2 preceding siblings ...)
2015-09-15 14:31 ` [PATCH v6 3/9] Input: goodix - reset device at init Irina Tirdea
@ 2015-09-15 14:31 ` Irina Tirdea
2015-09-25 14:40 ` Bastien Nocera
2015-09-15 14:31 ` [PATCH v6 5/9] Input: goodix - add power management support Irina Tirdea
` (4 subsequent siblings)
8 siblings, 1 reply; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree,
Irina Tirdea
Goodix devices can be configured by writing custom data to the device at
init. The configuration data is read with request_firmware from
"goodix_<id>_cfg.bin", where <id> is the product id read from the device
(e.g.: goodix_911_cfg.bin for Goodix GT911, goodix_9271_cfg.bin for
GT9271).
The configuration information has a specific format described in the Goodix
datasheet. It includes X/Y resolution, maximum supported touch points,
interrupt flags, various sesitivity factors and settings for advanced
features (like gesture recognition).
Before writing the firmware, it is necessary to reset the device. If
the device ACPI/DT information does not declare gpio pins (needed for
reset), writing the firmware will not be available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
drivers/input/touchscreen/goodix.c | 225 ++++++++++++++++++++++++++++++++-----
1 file changed, 194 insertions(+), 31 deletions(-)
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 9c58583..d6abd82 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -17,6 +17,7 @@
#include <linux/acpi.h>
#include <linux/delay.h>
#include <linux/dmi.h>
+#include <linux/firmware.h>
#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/input.h>
@@ -40,6 +41,9 @@ struct goodix_ts_data {
int cfg_len;
struct gpio_desc *gpiod_int;
struct gpio_desc *gpiod_rst;
+ u16 id;
+ u16 version;
+ char *cfg_name;
};
#define GOODIX_MAX_HEIGHT 4096
@@ -145,6 +149,39 @@ static int goodix_i2c_read(struct i2c_client *client,
return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0);
}
+/**
+ * goodix_i2c_write - write data to a register of the i2c slave device.
+ *
+ * @client: i2c device.
+ * @reg: the register to write to.
+ * @buf: raw data buffer to write.
+ * @len: length of the buffer to write
+ */
+static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf,
+ unsigned len)
+{
+ u8 *addr_buf;
+ struct i2c_msg msg;
+ int ret;
+
+ addr_buf = kmalloc(len + 2, GFP_KERNEL);
+ if (!addr_buf)
+ return -ENOMEM;
+
+ addr_buf[0] = reg >> 8;
+ addr_buf[1] = reg & 0xFF;
+ memcpy(&addr_buf[2], buf, len);
+
+ msg.flags = 0;
+ msg.addr = client->addr;
+ msg.buf = addr_buf;
+ msg.len = len + 2;
+
+ ret = i2c_transfer(client->adapter, &msg, 1);
+ kfree(addr_buf);
+ return ret < 0 ? ret : (ret != 1 ? -EIO : 0);
+}
+
static int goodix_get_cfg_len(u16 id)
{
switch (id) {
@@ -264,6 +301,73 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
return IRQ_HANDLED;
}
+/**
+ * goodix_check_cfg - Checks if config fw is valid
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: firmware config data
+ */
+static int goodix_check_cfg(struct goodix_ts_data *ts,
+ const struct firmware *cfg)
+{
+ int i, raw_cfg_len;
+ u8 check_sum = 0;
+
+ if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) {
+ dev_err(&ts->client->dev,
+ "The length of the config fw is not correct");
+ return -EINVAL;
+ }
+
+ raw_cfg_len = cfg->size - 2;
+ for (i = 0; i < raw_cfg_len; i++)
+ check_sum += cfg->data[i];
+ check_sum = (~check_sum) + 1;
+ if (check_sum != cfg->data[raw_cfg_len]) {
+ dev_err(&ts->client->dev,
+ "The checksum of the config fw is not correct");
+ return -EINVAL;
+ }
+
+ if (cfg->data[raw_cfg_len + 1] != 1) {
+ dev_err(&ts->client->dev,
+ "Config fw must have Config_Fresh register set");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * goodix_send_cfg - Write fw config to device
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: config firmware to write to device
+ */
+static int goodix_send_cfg(struct goodix_ts_data *ts,
+ const struct firmware *cfg)
+{
+ int error;
+
+ error = goodix_check_cfg(ts, cfg);
+ if (error)
+ return error;
+
+ error = goodix_i2c_write(ts->client, GOODIX_REG_CONFIG_DATA, cfg->data,
+ cfg->size);
+ if (error) {
+ dev_err(&ts->client->dev, "Failed to write config data: %d",
+ error);
+ return error;
+ }
+ dev_dbg(&ts->client->dev, "Config sent successfully.");
+
+ /* Let the firmware reconfigure itself, so sleep for 10ms */
+ usleep_range(10000, 11000);
+
+ return 0;
+}
+
static int goodix_int_sync(struct goodix_ts_data *ts)
{
int error;
@@ -406,30 +510,29 @@ static void goodix_read_config(struct goodix_ts_data *ts)
/**
* goodix_read_version - Read goodix touchscreen version
*
- * @client: the i2c client
- * @version: output buffer containing the version on success
- * @id: output buffer containing the id on success
+ * @ts: our goodix_ts_data pointer
*/
-static int goodix_read_version(struct i2c_client *client, u16 *version, u16 *id)
+static int goodix_read_version(struct goodix_ts_data *ts)
{
int error;
u8 buf[6];
char id_str[5];
- error = goodix_i2c_read(client, GOODIX_REG_ID, buf, sizeof(buf));
+ error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf));
if (error) {
- dev_err(&client->dev, "read version failed: %d\n", error);
+ dev_err(&ts->client->dev, "read version failed: %d\n", error);
return error;
}
memcpy(id_str, buf, 4);
id_str[4] = 0;
- if (kstrtou16(id_str, 10, id))
- *id = 0x1001;
+ if (kstrtou16(id_str, 10, &ts->id))
+ ts->id = 0x1001;
- *version = get_unaligned_le16(&buf[4]);
+ ts->version = get_unaligned_le16(&buf[4]);
- dev_info(&client->dev, "ID %d, version: %04x\n", *id, *version);
+ dev_info(&ts->client->dev, "ID %d, version: %04x\n", ts->id,
+ ts->version);
return 0;
}
@@ -463,13 +566,10 @@ static int goodix_i2c_test(struct i2c_client *client)
* goodix_request_input_dev - Allocate, populate and register the input device
*
* @ts: our goodix_ts_data pointer
- * @version: device firmware version
- * @id: device ID
*
* Must be called during probe
*/
-static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
- u16 id)
+static int goodix_request_input_dev(struct goodix_ts_data *ts)
{
int error;
@@ -493,8 +593,8 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
ts->input_dev->phys = "input/ts";
ts->input_dev->id.bustype = BUS_I2C;
ts->input_dev->id.vendor = 0x0416;
- ts->input_dev->id.product = id;
- ts->input_dev->id.version = version;
+ ts->input_dev->id.product = ts->id;
+ ts->input_dev->id.version = ts->version;
error = input_register_device(ts->input_dev);
if (error) {
@@ -506,13 +606,68 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
return 0;
}
+/**
+ * goodix_configure_dev - Finish device initialization
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * Must be called from request_firmware_wait callback to
+ * finish initialization of the device.
+ */
+static int goodix_configure_dev(struct goodix_ts_data *ts)
+{
+ int error;
+ unsigned long irq_flags;
+
+ goodix_read_config(ts);
+
+ error = goodix_request_input_dev(ts);
+ if (error)
+ return error;
+
+ irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
+ error = devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
+ NULL, goodix_ts_irq_handler,
+ irq_flags, ts->client->name, ts);
+ if (error) {
+ dev_err(&ts->client->dev, "request IRQ failed: %d\n", error);
+ return error;
+ }
+
+ return 0;
+}
+
+/**
+ * goodix_config_cb - Callback to finish device init
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * request_firmware_wait callback that finishes
+ * initialization of the device.
+ */
+static void goodix_config_cb(const struct firmware *cfg, void *ctx)
+{
+ struct goodix_ts_data *ts = (struct goodix_ts_data *)ctx;
+ int error;
+
+ if (cfg) {
+ /* send device configuration to the firmware */
+ error = goodix_send_cfg(ts, cfg);
+ if (error)
+ goto err_release_cfg;
+ }
+ goodix_configure_dev(ts);
+
+err_release_cfg:
+ kfree(ts->cfg_name);
+ release_firmware(cfg);
+}
+
static int goodix_ts_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct goodix_ts_data *ts;
- unsigned long irq_flags;
int error;
- u16 version_info, id_info;
dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
@@ -547,30 +702,38 @@ static int goodix_ts_probe(struct i2c_client *client,
return error;
}
- error = goodix_read_version(client, &version_info, &id_info);
+ error = goodix_read_version(ts);
if (error) {
dev_err(&client->dev, "Read version failed.\n");
return error;
}
- ts->cfg_len = goodix_get_cfg_len(id_info);
+ ts->cfg_len = goodix_get_cfg_len(ts->id);
goodix_read_config(ts);
- error = goodix_request_input_dev(ts, version_info, id_info);
- if (error)
- return error;
+ if (ts->gpiod_int && ts->gpiod_rst) {
+ /* update device config */
+ ts->cfg_name = kasprintf(GFP_KERNEL, "goodix_%d_cfg.bin",
+ ts->id);
+ if (!ts->cfg_name)
+ return -ENOMEM;
+
+ error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name,
+ &client->dev, GFP_KERNEL, ts,
+ goodix_config_cb);
+ if (error) {
+ dev_err(&client->dev,
+ "Failed to invoke firmware loader: %d\n",
+ error);
+ kfree(ts->cfg_name);
+ return error;
+ }
- irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
- error = devm_request_threaded_irq(&ts->client->dev, client->irq,
- NULL, goodix_ts_irq_handler,
- irq_flags, client->name, ts);
- if (error) {
- dev_err(&client->dev, "request IRQ failed: %d\n", error);
- return error;
+ return 0;
}
- return 0;
+ return goodix_configure_dev(ts);
}
static const struct i2c_device_id goodix_ts_id[] = {
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v6 4/9] Input: goodix - write configuration data to device
2015-09-15 14:31 ` [PATCH v6 4/9] Input: goodix - write configuration data to device Irina Tirdea
@ 2015-09-25 14:40 ` Bastien Nocera
[not found] ` <1443192040.17020.26.camel-0MeiytkfxGOsTnJN9+BGXg@public.gmane.org>
0 siblings, 1 reply; 13+ messages in thread
From: Bastien Nocera @ 2015-09-25 14:40 UTC (permalink / raw)
To: Irina Tirdea, Dmitry Torokhov, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree
On Tue, 2015-09-15 at 17:31 +0300, Irina Tirdea wrote:
> Goodix devices can be configured by writing custom data to the device
> at
> init. The configuration data is read with request_firmware from
> "goodix_<id>_cfg.bin", where <id> is the product id read from the
> device
> (e.g.: goodix_911_cfg.bin for Goodix GT911, goodix_9271_cfg.bin for
> GT9271).
>
> The configuration information has a specific format described in the
> Goodix
> datasheet. It includes X/Y resolution, maximum supported touch
> points,
> interrupt flags, various sesitivity factors and settings for advanced
sensitivity.
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v6 5/9] Input: goodix - add power management support
2015-09-15 14:31 [PATCH v6 0/9] Goodix touchscreen enhancements Irina Tirdea
` (3 preceding siblings ...)
2015-09-15 14:31 ` [PATCH v6 4/9] Input: goodix - write configuration data to device Irina Tirdea
@ 2015-09-15 14:31 ` Irina Tirdea
2015-09-15 14:31 ` [PATCH v6 6/9] Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send Irina Tirdea
` (3 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree,
Irina Tirdea
Implement suspend/resume for goodix driver.
The suspend and resume process uses the gpio pins.
If the device ACPI/DT information does not declare gpio pins,
suspend/resume will not be available for these devices.
This is based on Goodix datasheets for GT911 and GT9271
and on Goodix driver gt9xx.c for Android (publicly available
in Android kernel trees for various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
drivers/input/touchscreen/goodix.c | 94 ++++++++++++++++++++++++++++++++++++--
1 file changed, 89 insertions(+), 5 deletions(-)
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index d6abd82..1993b6c 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -44,6 +44,7 @@ struct goodix_ts_data {
u16 id;
u16 version;
char *cfg_name;
+ unsigned long irq_flags;
};
#define GOODIX_MAX_HEIGHT 4096
@@ -57,6 +58,9 @@ struct goodix_ts_data {
#define GOODIX_CONFIG_967_LENGTH 228
/* Register defines */
+#define GOODIX_REG_COMMAND 0x8040
+#define GOODIX_CMD_SCREEN_OFF 0x05
+
#define GOODIX_READ_COOR_ADDR 0x814E
#define GOODIX_REG_CONFIG_DATA 0x8047
#define GOODIX_REG_ID 0x8140
@@ -182,6 +186,11 @@ static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf,
return ret < 0 ? ret : (ret != 1 ? -EIO : 0);
}
+static int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
+{
+ return goodix_i2c_write(client, reg, &value, sizeof(value));
+}
+
static int goodix_get_cfg_len(u16 id)
{
switch (id) {
@@ -301,6 +310,18 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static void goodix_free_irq(struct goodix_ts_data *ts)
+{
+ devm_free_irq(&ts->client->dev, ts->client->irq, ts);
+}
+
+static int goodix_request_irq(struct goodix_ts_data *ts)
+{
+ return devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
+ NULL, goodix_ts_irq_handler,
+ ts->irq_flags, ts->client->name, ts);
+}
+
/**
* goodix_check_cfg - Checks if config fw is valid
*
@@ -617,7 +638,6 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts)
static int goodix_configure_dev(struct goodix_ts_data *ts)
{
int error;
- unsigned long irq_flags;
goodix_read_config(ts);
@@ -625,10 +645,8 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
if (error)
return error;
- irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
- error = devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
- NULL, goodix_ts_irq_handler,
- irq_flags, ts->client->name, ts);
+ ts->irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
+ error = goodix_request_irq(ts);
if (error) {
dev_err(&ts->client->dev, "request IRQ failed: %d\n", error);
return error;
@@ -736,6 +754,71 @@ static int goodix_ts_probe(struct i2c_client *client,
return goodix_configure_dev(ts);
}
+static int __maybe_unused goodix_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct goodix_ts_data *ts = i2c_get_clientdata(client);
+ int error;
+
+ /* We need gpio pins to suspend/resume */
+ if (!ts->gpiod_int || !ts->gpiod_rst)
+ return 0;
+
+ /* Free IRQ as IRQ pin is used as output in the suspend sequence */
+ goodix_free_irq(ts);
+ /* Output LOW on the INT pin for 5 ms */
+ error = gpiod_direction_output(ts->gpiod_int, 0);
+ if (error) {
+ goodix_request_irq(ts);
+ return error;
+ }
+ usleep_range(5000, 6000);
+
+ error = goodix_i2c_write_u8(ts->client, GOODIX_REG_COMMAND,
+ GOODIX_CMD_SCREEN_OFF);
+ if (error) {
+ dev_err(&ts->client->dev, "Screen off command failed\n");
+ gpiod_direction_input(ts->gpiod_int);
+ goodix_request_irq(ts);
+ return -EAGAIN;
+ }
+
+ /*
+ * The datasheet specifies that the interval between sending screen-off
+ * command and wake-up should be longer than 58 ms. To avoid waking up
+ * sooner, delay 58ms here.
+ */
+ msleep(58);
+ return 0;
+}
+
+static int __maybe_unused goodix_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct goodix_ts_data *ts = i2c_get_clientdata(client);
+ int error;
+
+ if (!ts->gpiod_int || !ts->gpiod_rst)
+ return 0;
+
+ /*
+ * Exit sleep mode by outputting HIGH level to INT pin
+ * for 2ms~5ms.
+ */
+ error = gpiod_direction_output(ts->gpiod_int, 1);
+ if (error)
+ return error;
+ usleep_range(2000, 5000);
+
+ error = goodix_int_sync(ts);
+ if (error)
+ return error;
+
+ return goodix_request_irq(ts);
+}
+
+static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
+
static const struct i2c_device_id goodix_ts_id[] = {
{ "GDIX1001:00", 0 },
{ }
@@ -771,6 +854,7 @@ static struct i2c_driver goodix_ts_driver = {
.owner = THIS_MODULE,
.acpi_match_table = ACPI_PTR(goodix_acpi_match),
.of_match_table = of_match_ptr(goodix_of_match),
+ .pm = &goodix_pm_ops,
},
};
module_i2c_driver(goodix_ts_driver);
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v6 6/9] Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
2015-09-15 14:31 [PATCH v6 0/9] Goodix touchscreen enhancements Irina Tirdea
` (4 preceding siblings ...)
2015-09-15 14:31 ` [PATCH v6 5/9] Input: goodix - add power management support Irina Tirdea
@ 2015-09-15 14:31 ` Irina Tirdea
2015-09-15 14:31 ` [PATCH v6 7/9] Input: goodix - add support for ESD Irina Tirdea
` (2 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree,
Irina Tirdea
Use goodix_i2c_write_u8 instead of i2c_master_send to simplify code.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
drivers/input/touchscreen/goodix.c | 7 +------
1 file changed, 1 insertion(+), 6 deletions(-)
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 1993b6c..ee87d38 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -295,16 +295,11 @@ static void goodix_process_events(struct goodix_ts_data *ts)
*/
static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
{
- static const u8 end_cmd[] = {
- GOODIX_READ_COOR_ADDR >> 8,
- GOODIX_READ_COOR_ADDR & 0xff,
- 0
- };
struct goodix_ts_data *ts = dev_id;
goodix_process_events(ts);
- if (i2c_master_send(ts->client, end_cmd, sizeof(end_cmd)) < 0)
+ if (goodix_i2c_write_u8(ts->client, GOODIX_READ_COOR_ADDR, 0) < 0)
dev_err(&ts->client->dev, "I2C write end_cmd error\n");
return IRQ_HANDLED;
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v6 7/9] Input: goodix - add support for ESD
2015-09-15 14:31 [PATCH v6 0/9] Goodix touchscreen enhancements Irina Tirdea
` (5 preceding siblings ...)
2015-09-15 14:31 ` [PATCH v6 6/9] Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send Irina Tirdea
@ 2015-09-15 14:31 ` Irina Tirdea
[not found] ` <1442327483-19407-1-git-send-email-irina.tirdea-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
2015-09-15 14:31 ` [PATCH v6 9/9] Input: goodix - add runtime power management support Irina Tirdea
8 siblings, 0 replies; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree,
Irina Tirdea
Add ESD (Electrostatic Discharge) protection mechanism.
The driver enables ESD protection in HW and checks a register
to determine if ESD occurred. If ESD is signalled by the HW,
the driver will reset the device.
The ESD poll time (in ms) can be set through the sysfs property
esd_timeout. If it is set to 0, ESD protection is disabled.
Recommended value is 2000 ms. The initial value for ESD timeout
can be set through esd-recovery-timeout-ms ACPI/DT property.
If there is no such property defined, ESD protection is disabled.
For ACPI 5.1, the property can be specified using _DSD properties:
Device (STAC)
{
Name (_HID, "GDIX1001")
...
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package (2) { "esd-recovery-timeout-ms", Package(1) { 2000 }},
...
}
})
}
The ESD protection mechanism is only available if the gpio pins
are properly initialized from ACPI/DT.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
.../bindings/input/touchscreen/goodix.txt | 6 +
drivers/input/touchscreen/goodix.c | 174 ++++++++++++++++++++-
2 files changed, 173 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index c0715f8..5891ad1 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -14,6 +14,12 @@ Required properties:
- interrupts : Interrupt to which the chip is connected
- gpios : GPIOS the chip is connected to: first one is the
interrupt gpio and second one the reset gpio.
+Optional properties:
+
+ - esd-recovery-timeout-ms : ESD poll time (in milli seconds) for the driver to
+ check if ESD occurred and in that case reset the
+ device. ESD is disabled if this property is not set
+ or is set to 0.
Example:
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index ee87d38..a5dd1bd 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -45,8 +45,12 @@ struct goodix_ts_data {
u16 version;
char *cfg_name;
unsigned long irq_flags;
+ atomic_t esd_timeout;
+ struct delayed_work esd_work;
};
+#define GOODIX_DEVICE_ESD_TIMEOUT_PROPERTY "esd-recovery-timeout-ms"
+
#define GOODIX_MAX_HEIGHT 4096
#define GOODIX_MAX_WIDTH 4096
#define GOODIX_INT_TRIGGER 1
@@ -60,6 +64,8 @@ struct goodix_ts_data {
/* Register defines */
#define GOODIX_REG_COMMAND 0x8040
#define GOODIX_CMD_SCREEN_OFF 0x05
+#define GOODIX_CMD_ESD_ENABLED 0xAA
+#define GOODIX_REG_ESD_CHECK 0x8041
#define GOODIX_READ_COOR_ADDR 0x814E
#define GOODIX_REG_CONFIG_DATA 0x8047
@@ -426,6 +432,117 @@ static int goodix_reset(struct goodix_ts_data *ts)
return goodix_int_sync(ts);
}
+static void goodix_disable_esd(struct goodix_ts_data *ts)
+{
+ if (!atomic_read(&ts->esd_timeout))
+ return;
+ cancel_delayed_work_sync(&ts->esd_work);
+}
+
+static int goodix_enable_esd(struct goodix_ts_data *ts)
+{
+ int error, esd_timeout;
+
+ esd_timeout = atomic_read(&ts->esd_timeout);
+ if (!esd_timeout)
+ return 0;
+
+ error = goodix_i2c_write_u8(ts->client, GOODIX_REG_ESD_CHECK,
+ GOODIX_CMD_ESD_ENABLED);
+ if (error) {
+ dev_err(&ts->client->dev, "Failed to enable ESD: %d\n", error);
+ return error;
+ }
+
+ schedule_delayed_work(&ts->esd_work, round_jiffies_relative(
+ msecs_to_jiffies(esd_timeout)));
+ return 0;
+}
+
+static void goodix_esd_work(struct work_struct *work)
+{
+ struct goodix_ts_data *ts = container_of(work, struct goodix_ts_data,
+ esd_work.work);
+ int retries = 3, error;
+ u8 esd_data[2];
+ const struct firmware *cfg = NULL;
+
+ while (--retries) {
+ error = goodix_i2c_read(ts->client, GOODIX_REG_COMMAND,
+ esd_data, sizeof(esd_data));
+ if (error)
+ continue;
+ if (esd_data[0] != GOODIX_CMD_ESD_ENABLED &&
+ esd_data[1] == GOODIX_CMD_ESD_ENABLED) {
+ /* feed the watchdog */
+ goodix_i2c_write_u8(ts->client,
+ GOODIX_REG_COMMAND,
+ GOODIX_CMD_ESD_ENABLED);
+ break;
+ }
+ }
+
+ if (!retries) {
+ dev_dbg(&ts->client->dev, "Performing ESD recovery.\n");
+ goodix_free_irq(ts);
+ goodix_reset(ts);
+ error = request_firmware(&cfg, ts->cfg_name, &ts->client->dev);
+ if (!error) {
+ goodix_send_cfg(ts, cfg);
+ release_firmware(cfg);
+ }
+ goodix_request_irq(ts);
+ goodix_enable_esd(ts);
+ return;
+ }
+
+ schedule_delayed_work(&ts->esd_work, round_jiffies_relative(
+ msecs_to_jiffies(atomic_read(&ts->esd_timeout))));
+}
+
+static ssize_t goodix_esd_timeout_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct goodix_ts_data *ts = dev_get_drvdata(dev);
+
+ return scnprintf(buf, PAGE_SIZE, "%d\n", atomic_read(&ts->esd_timeout));
+}
+
+static ssize_t goodix_esd_timeout_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct goodix_ts_data *ts = dev_get_drvdata(dev);
+ int error, esd_timeout, new_esd_timeout;
+
+ error = kstrtouint(buf, 10, &new_esd_timeout);
+ if (error)
+ return error;
+
+ esd_timeout = atomic_read(&ts->esd_timeout);
+ if (esd_timeout && !new_esd_timeout)
+ goodix_disable_esd(ts);
+
+ atomic_set(&ts->esd_timeout, new_esd_timeout);
+ if (!esd_timeout && new_esd_timeout)
+ goodix_enable_esd(ts);
+
+ return count;
+}
+
+/* ESD timeout in ms. Default disabled (0). Recommended 2000 ms. */
+static DEVICE_ATTR(esd_timeout, S_IRUGO | S_IWUSR, goodix_esd_timeout_show,
+ goodix_esd_timeout_store);
+
+static struct attribute *goodix_attrs[] = {
+ &dev_attr_esd_timeout.attr,
+ NULL
+};
+
+static const struct attribute_group goodix_attr_group = {
+ .attrs = goodix_attrs,
+};
+
/**
* goodix_get_gpio_config - Get GPIO config from ACPI/DT
*
@@ -647,6 +764,8 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
return error;
}
+ goodix_enable_esd(ts);
+
return 0;
}
@@ -672,7 +791,6 @@ static void goodix_config_cb(const struct firmware *cfg, void *ctx)
goodix_configure_dev(ts);
err_release_cfg:
- kfree(ts->cfg_name);
release_firmware(cfg);
}
@@ -680,7 +798,7 @@ static int goodix_ts_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct goodix_ts_data *ts;
- int error;
+ int error, esd_timeout;
dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
@@ -695,6 +813,7 @@ static int goodix_ts_probe(struct i2c_client *client,
ts->client = client;
i2c_set_clientdata(client, ts);
+ INIT_DELAYED_WORK(&ts->esd_work, goodix_esd_work);
error = goodix_get_gpio_config(ts, id);
if (error)
@@ -726,11 +845,28 @@ static int goodix_ts_probe(struct i2c_client *client,
goodix_read_config(ts);
if (ts->gpiod_int && ts->gpiod_rst) {
+ error = device_property_read_u32(&ts->client->dev,
+ GOODIX_DEVICE_ESD_TIMEOUT_PROPERTY,
+ &esd_timeout);
+ if (!error)
+ atomic_set(&ts->esd_timeout, esd_timeout);
+
+ error = sysfs_create_group(&client->dev.kobj,
+ &goodix_attr_group);
+ if (error) {
+ dev_err(&client->dev,
+ "Failed to create sysfs group: %d\n",
+ error);
+ return error;
+ }
+
/* update device config */
ts->cfg_name = kasprintf(GFP_KERNEL, "goodix_%d_cfg.bin",
ts->id);
- if (!ts->cfg_name)
- return -ENOMEM;
+ if (!ts->cfg_name) {
+ error = -ENOMEM;
+ goto err_sysfs_remove_group;
+ }
error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name,
&client->dev, GFP_KERNEL, ts,
@@ -739,14 +875,32 @@ static int goodix_ts_probe(struct i2c_client *client,
dev_err(&client->dev,
"Failed to invoke firmware loader: %d\n",
error);
- kfree(ts->cfg_name);
- return error;
+ goto err_free_cfg_name;
}
return 0;
}
return goodix_configure_dev(ts);
+
+err_free_cfg_name:
+ if (ts->gpiod_int && ts->gpiod_rst)
+ kfree(ts->cfg_name);
+err_sysfs_remove_group:
+ if (ts->gpiod_int && ts->gpiod_rst)
+ sysfs_remove_group(&client->dev.kobj, &goodix_attr_group);
+ return error;
+}
+
+static int goodix_ts_remove(struct i2c_client *client)
+{
+ struct goodix_ts_data *ts = i2c_get_clientdata(client);
+
+ if (ts->gpiod_int && ts->gpiod_rst)
+ sysfs_remove_group(&client->dev.kobj, &goodix_attr_group);
+ goodix_disable_esd(ts);
+ kfree(ts->cfg_name);
+ return 0;
}
static int __maybe_unused goodix_suspend(struct device *dev)
@@ -759,6 +913,7 @@ static int __maybe_unused goodix_suspend(struct device *dev)
if (!ts->gpiod_int || !ts->gpiod_rst)
return 0;
+ goodix_disable_esd(ts);
/* Free IRQ as IRQ pin is used as output in the suspend sequence */
goodix_free_irq(ts);
/* Output LOW on the INT pin for 5 ms */
@@ -809,7 +964,11 @@ static int __maybe_unused goodix_resume(struct device *dev)
if (error)
return error;
- return goodix_request_irq(ts);
+ error = goodix_request_irq(ts);
+ if (error)
+ return error;
+
+ return goodix_enable_esd(ts);
}
static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
@@ -843,6 +1002,7 @@ MODULE_DEVICE_TABLE(of, goodix_of_match);
static struct i2c_driver goodix_ts_driver = {
.probe = goodix_ts_probe,
+ .remove = goodix_ts_remove,
.id_table = goodix_ts_id,
.driver = {
.name = "Goodix-TS",
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread[parent not found: <1442327483-19407-1-git-send-email-irina.tirdea-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>]
* [PATCH v6 8/9] Input: goodix - add sysfs interface to dump config
[not found] ` <1442327483-19407-1-git-send-email-irina.tirdea-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
@ 2015-09-15 14:31 ` Irina Tirdea
0 siblings, 0 replies; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin,
linux-input-u79uwXL29TY76Z2rM5mHXA
Cc: Mark Rutland, Octavian Purdila,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, Irina Tirdea
Goodix devices have a configuration information register area that
specify various parameters for the device. The configuration information
has a specific format described in the Goodix datasheet. It includes X/Y
resolution, maximum supported touch points, interrupt flags, various
sesitivity factors and settings for advanced features (like gesture
recognition).
Export a sysfs interface that would allow reading the configuration
information. The default device configuration can be used as a starting
point for creating a valid configuration firmware used by the device at
init time to update its configuration.
This sysfs interface will be exported only if the gpio pins are properly
initialized from ACPI/DT.
Signed-off-by: Irina Tirdea <irina.tirdea-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
---
drivers/input/touchscreen/goodix.c | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index a5dd1bd..641a9e3 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -530,12 +530,35 @@ static ssize_t goodix_esd_timeout_store(struct device *dev,
return count;
}
+static ssize_t goodix_dump_config_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct goodix_ts_data *ts = dev_get_drvdata(dev);
+ u8 config[GOODIX_CONFIG_MAX_LENGTH];
+ int error, count = 0, i;
+
+ error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
+ config, ts->cfg_len);
+ if (error) {
+ dev_warn(&ts->client->dev,
+ "Error reading config (%d)\n", error);
+ return error;
+ }
+
+ for (i = 0; i < ts->cfg_len; i++)
+ count += scnprintf(buf + count, PAGE_SIZE - count, "%02x ",
+ config[i]);
+ return count;
+}
+
/* ESD timeout in ms. Default disabled (0). Recommended 2000 ms. */
static DEVICE_ATTR(esd_timeout, S_IRUGO | S_IWUSR, goodix_esd_timeout_show,
goodix_esd_timeout_store);
+static DEVICE_ATTR(dump_config, S_IRUGO, goodix_dump_config_show, NULL);
static struct attribute *goodix_attrs[] = {
&dev_attr_esd_timeout.attr,
+ &dev_attr_dump_config.attr,
NULL
};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v6 9/9] Input: goodix - add runtime power management support
2015-09-15 14:31 [PATCH v6 0/9] Goodix touchscreen enhancements Irina Tirdea
` (7 preceding siblings ...)
[not found] ` <1442327483-19407-1-git-send-email-irina.tirdea-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
@ 2015-09-15 14:31 ` Irina Tirdea
8 siblings, 0 replies; 13+ messages in thread
From: Irina Tirdea @ 2015-09-15 14:31 UTC (permalink / raw)
To: Dmitry Torokhov, Bastien Nocera, Aleksei Mamlin, linux-input
Cc: Mark Rutland, Octavian Purdila, linux-kernel, devicetree,
Irina Tirdea
Add support for runtime power management so that the device is
turned off when not used (when the userspace holds no open
handles of the input device). The device uses autosuspend with a
default delay of 2 seconds, so the device will suspend if no
handles to it are open for 2 seconds.
The runtime management support is only available if the gpio pins
are properly initialized from ACPI/DT.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
drivers/input/touchscreen/goodix.c | 63 +++++++++++++++++++++++++++++++++++---
1 file changed, 59 insertions(+), 4 deletions(-)
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 641a9e3..a0b6067 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -27,6 +27,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of.h>
+#include <linux/pm_runtime.h>
#include <linux/slab.h>
#include <asm/unaligned.h>
@@ -75,6 +76,8 @@ struct goodix_ts_data {
#define MAX_CONTACTS_LOC 5
#define TRIGGER_LOC 6
+#define GOODIX_AUTOSUSPEND_DELAY_MS 2000
+
static const unsigned long goodix_irq_flags[] = {
IRQ_TYPE_EDGE_RISING,
IRQ_TYPE_EDGE_FALLING,
@@ -566,6 +569,33 @@ static const struct attribute_group goodix_attr_group = {
.attrs = goodix_attrs,
};
+static int goodix_open(struct input_dev *input_dev)
+{
+ struct goodix_ts_data *ts = input_get_drvdata(input_dev);
+ int error;
+
+ if (!ts->gpiod_int || !ts->gpiod_rst)
+ return 0;
+
+ error = pm_runtime_get_sync(&ts->client->dev);
+ if (error < 0) {
+ pm_runtime_put_noidle(&ts->client->dev);
+ return error;
+ }
+ return 0;
+}
+
+static void goodix_close(struct input_dev *input_dev)
+{
+ struct goodix_ts_data *ts = input_get_drvdata(input_dev);
+
+ if (!ts->gpiod_int || !ts->gpiod_rst)
+ return;
+
+ pm_runtime_mark_last_busy(&ts->client->dev);
+ pm_runtime_put_autosuspend(&ts->client->dev);
+}
+
/**
* goodix_get_gpio_config - Get GPIO config from ACPI/DT
*
@@ -751,6 +781,9 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts)
ts->input_dev->id.vendor = 0x0416;
ts->input_dev->id.product = ts->id;
ts->input_dev->id.version = ts->version;
+ ts->input_dev->open = goodix_open;
+ ts->input_dev->close = goodix_close;
+ input_set_drvdata(ts->input_dev, ts);
error = input_register_device(ts->input_dev);
if (error) {
@@ -798,7 +831,8 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
* @ts: our goodix_ts_data pointer
*
* request_firmware_wait callback that finishes
- * initialization of the device.
+ * initialization of the device. This will only be called
+ * when ts->gpiod_int and ts->gpiod_rst are properly initialized.
*/
static void goodix_config_cb(const struct firmware *cfg, void *ctx)
{
@@ -811,7 +845,21 @@ static void goodix_config_cb(const struct firmware *cfg, void *ctx)
if (error)
goto err_release_cfg;
}
- goodix_configure_dev(ts);
+ error = goodix_configure_dev(ts);
+ if (error)
+ goto err_release_cfg;
+
+ error = pm_runtime_set_active(&ts->client->dev);
+ if (error) {
+ dev_err(&ts->client->dev, "failed to set active: %d\n", error);
+ goto err_release_cfg;
+ }
+ /* input_dev is a child of client->dev, ignore it for runtime pm */
+ pm_suspend_ignore_children(&ts->client->dev, true);
+ pm_runtime_enable(&ts->client->dev);
+ pm_runtime_set_autosuspend_delay(&ts->client->dev,
+ GOODIX_AUTOSUSPEND_DELAY_MS);
+ pm_runtime_use_autosuspend(&ts->client->dev);
err_release_cfg:
release_firmware(cfg);
@@ -919,8 +967,12 @@ static int goodix_ts_remove(struct i2c_client *client)
{
struct goodix_ts_data *ts = i2c_get_clientdata(client);
- if (ts->gpiod_int && ts->gpiod_rst)
+ if (ts->gpiod_int && ts->gpiod_rst) {
+ pm_runtime_disable(&client->dev);
+ pm_runtime_set_suspended(&client->dev);
+ pm_runtime_put_noidle(&client->dev);
sysfs_remove_group(&client->dev.kobj, &goodix_attr_group);
+ }
goodix_disable_esd(ts);
kfree(ts->cfg_name);
return 0;
@@ -994,7 +1046,10 @@ static int __maybe_unused goodix_resume(struct device *dev)
return goodix_enable_esd(ts);
}
-static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
+static const struct dev_pm_ops goodix_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(goodix_suspend, goodix_resume)
+ SET_RUNTIME_PM_OPS(goodix_suspend, goodix_resume, NULL)
+};
static const struct i2c_device_id goodix_ts_id[] = {
{ "GDIX1001:00", 0 },
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread