devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Andreas Dannenberg <dannenberg@ti.com>
To: Laurentiu Palcu <laurentiu.palcu@intel.com>
Cc: Sebastian Reichel <sre@kernel.org>,
	Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>,
	David Woodhouse <dwmw2@infradead.org>,
	Krzysztof Kozlowski <k.kozlowski@samsung.com>,
	Ramakrishna Pallala <ramakrishna.pallala@intel.com>,
	linux-pm@vger.kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH v5 01/11] dt: power: bq24257-charger: Cover additional devices
Date: Wed, 23 Sep 2015 09:13:02 -0500	[thread overview]
Message-ID: <20150923141240.GB6289@borg> (raw)
In-Reply-To: <20150923081456.GC15509@lpalcu-desk>

On Wed, Sep 23, 2015 at 11:14:56AM +0300, Laurentiu Palcu wrote:
> Hi,
> 
> On Wed, Sep 23, 2015 at 02:34:15AM +0200, Sebastian Reichel wrote:
> > Hi,
> > 
> > On Tue, Sep 22, 2015 at 04:58:24PM -0500, Andreas Dannenberg wrote:
> > > On Tue, Sep 22, 2015 at 06:24:48PM +0200, Sebastian Reichel wrote:
> > > > On Fri, Sep 18, 2015 at 04:39:49PM -0500, Andreas Dannenberg wrote:
> > > > > Extend the bq24257 charger's device tree documentation to cover the
> > > > > bq24250 and bq24251 devices as well feature additions.
> > > > 
> > > > The binding looks fine to except for:
> > > > 
> > > > > +- stat-gpios: GPIO used for the devices STAT_IN pin. Alternatively the pin can
> > > > > +    also be defined through the standard interrupt definition properties (see
> > > > > +    optional properties section below). Only use one method.
> > > > 
> > > > Why do you expose two ways for this?
> > > 
> > > Hi Sebastian. The original driver exposed this - it just didn't
> > > document it in the DT binding doc. I'm not sure why this was introduced
> > > in the first place (Laurentiu?). I know we can't change the API but
> > > since it was never documented maybe we can remove it?
> > 
> > It seems this is neither documented, nor used. So I guess it can be
> > removed. Let's wait for feedback from Laurentiu, though.
> This was needed to have both ACPI and DT enumeration work. At the time I
> wrote the driver, GpioInt resources in ACPI were not passed to the
> driver in client->irq, as opposed to DT enumeration.
> 
> However, conveniently enough, the patch below landed in master by the
> same time bq24257 driver went in. So, I believe it should be safe now to
> remove the stat-gpio probing.
> 
> commit 845c877009cf014b971aab7f54613f9185a824b0
> Author: Mika Westerberg <mika.westerberg@linux.intel.com>
> Date:   Wed May 6 13:29:08 2015 +0300
> 
>     i2c / ACPI: Assign IRQ for devices that have GpioInt automatically
> 

Thanks for the background! I'll be happy to simplify this as part of my
patch series.

--
Andreas Dannenberg
Texas Instruments Inc

  reply	other threads:[~2015-09-23 14:13 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-09-18 21:39 [PATCH v5 00/11] power: bq24257: Add support for bq24250/bq24251 Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 01/11] dt: power: bq24257-charger: Cover additional devices Andreas Dannenberg
2015-09-22 16:24   ` Sebastian Reichel
2015-09-22 21:58     ` Andreas Dannenberg
2015-09-23  0:34       ` Sebastian Reichel
2015-09-23  8:14         ` Laurentiu Palcu
2015-09-23 14:13           ` Andreas Dannenberg [this message]
2015-09-18 21:39 ` [PATCH v5 02/11] power: bq24257: Add basic support for bq24250/bq24251 Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 03/11] power: bq24257: Add bit definition for temp sense enable Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 04/11] power: bq24257: Allow manual setting of input current limit Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 06/11] power: bq24257: Use managed power supply register Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 07/11] power: bq24257: Add over voltage protection setting support Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 08/11] power: bq24257: Add input DPM voltage threshold " Andreas Dannenberg
     [not found] ` <1442612399-341-1-git-send-email-dannenberg-l0cyMroinI0@public.gmane.org>
2015-09-18 21:39   ` [PATCH v5 05/11] power: bq24257: Add SW-based approach for Power Good determination Andreas Dannenberg
2015-09-22 19:37     ` Sebastian Reichel
2015-09-23 19:34       ` Andreas Dannenberg
2015-09-23 20:02         ` Andreas Dannenberg
2015-09-18 21:39   ` [PATCH v5 09/11] power: bq24257: Allow input current limit sysfs access Andreas Dannenberg
2015-09-22 19:16     ` Sebastian Reichel
2015-09-22 22:10       ` Andreas Dannenberg
2015-09-23  0:29         ` Sebastian Reichel
2015-09-23 14:11           ` Andreas Dannenberg
2015-09-23 15:02             ` Sebastian Reichel
2015-09-23 18:32               ` Andreas Dannenberg
2015-09-23 18:53                 ` Sebastian Reichel
2015-09-23 19:47                   ` Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 10/11] power: bq24257: Add various device-specific sysfs properties Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 11/11] power: bq24257: Add platform data based initialization Andreas Dannenberg
2015-09-22 19:29   ` Sebastian Reichel
2015-09-22 19:31 ` [PATCH v5 00/11] power: bq24257: Add support for bq24250/bq24251 Sebastian Reichel

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20150923141240.GB6289@borg \
    --to=dannenberg@ti.com \
    --cc=dbaryshkov@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dwmw2@infradead.org \
    --cc=k.kozlowski@samsung.com \
    --cc=laurentiu.palcu@intel.com \
    --cc=linux-pm@vger.kernel.org \
    --cc=ramakrishna.pallala@intel.com \
    --cc=sre@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).