* [PATCH v2 1/5] dt-bindings: mfd: s2mps11: add documentation for s2mps15 PMIC [not found] <1445855803-26973-1-git-send-email-alim.akhtar@samsung.com> @ 2015-10-26 10:36 ` Alim Akhtar 2015-10-26 11:09 ` Lee Jones 0 siblings, 1 reply; 3+ messages in thread From: Alim Akhtar @ 2015-10-26 10:36 UTC (permalink / raw) To: lee.jones, broonie Cc: k.kozlowski, mturquette, linux-samsung-soc, linux-clk, rtc-linux, linux-kernel, Thomas Abraham, devicetree From: Thomas Abraham <thomas.ab@samsung.com> Add dt-binding documentation for s2mps15 PMIC device. The s2mps15 device is similar to s2mps11/14 PMIC device and has 27 LDO and 10 buck regulators. Cc: devicetree@vger.kernel.org Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> --- Documentation/devicetree/bindings/mfd/s2mps11.txt | 23 ++++++++++++++------- 1 file changed, 15 insertions(+), 8 deletions(-) diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 890f0b0e1643..c0427c9d0886 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,5 +1,5 @@ -* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator +* Samsung S2MPS11/13/14/15 and S2MPU02 Voltage and Current Regulator The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is @@ -7,8 +7,12 @@ interfaced to the host controller using an I2C interface. Each sub-block is addressed by the host system using different I2C slave addresses. Required properties: -- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" - or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". +- compatible: Should be one of the following + - "samsung,s2mps11-pmic" + - "samsung,s2mps13-pmic" + - "samsung,s2mps14-pmic" + - "samsung,s2mps15-pmic" + - "samsung,s2mpu02-pmic". - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. Optional properties: @@ -24,7 +28,7 @@ Optional properties: unwanted buck warm reset (setting buck voltages to default values). Optional nodes: -- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 +- clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768 KHz outputs, so to register these as clocks with common clock framework instantiate a sub-node named "clocks". It uses the common clock binding documented in : @@ -37,12 +41,13 @@ Optional nodes: the clock which they consume. Clock ID Devices ---------------------------------------------------------- - 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 - 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 - 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 + 32KhzCP 1 S2MPS11, S2MPS13, S2MPS15, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", - "samsung,s2mps14-clk", "samsung,s5m8767-clk" + "samsung,s2mps14-clk", "samsung,s2mps15-clk", + "samsung,s5m8767-clk" - regulators: The regulators of s2mps11 that have to be instantiated should be included in a sub-node named 'regulators'. Regulator nodes included in this @@ -90,6 +95,7 @@ as per the datasheet of s2mps11. - S2MPS11: 1 to 38 - S2MPS13: 1 to 40 - S2MPS14: 1 to 25 + - S2MPS15: 1 to 27 - S2MPU02: 1 to 28 - Example: LDO1, LDO2, LDO28 - BUCKn @@ -97,6 +103,7 @@ as per the datasheet of s2mps11. - S2MPS11: 1 to 10 - S2MPS13: 1 to 10 - S2MPS14: 1 to 5 + - S2MPS15: 1 to 10 - S2MPU02: 1 to 7 - Example: BUCK1, BUCK2, BUCK9 -- 1.7.10.4 ^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v2 1/5] dt-bindings: mfd: s2mps11: add documentation for s2mps15 PMIC 2015-10-26 10:36 ` [PATCH v2 1/5] dt-bindings: mfd: s2mps11: add documentation for s2mps15 PMIC Alim Akhtar @ 2015-10-26 11:09 ` Lee Jones 2015-10-26 12:42 ` Alim Akhtar 0 siblings, 1 reply; 3+ messages in thread From: Lee Jones @ 2015-10-26 11:09 UTC (permalink / raw) To: Alim Akhtar Cc: broonie, k.kozlowski, mturquette, linux-samsung-soc, linux-clk, rtc-linux, linux-kernel, Thomas Abraham, devicetree On Mon, 26 Oct 2015, Alim Akhtar wrote: > From: Thomas Abraham <thomas.ab@samsung.com> > > Add dt-binding documentation for s2mps15 PMIC device. The s2mps15 device > is similar to s2mps11/14 PMIC device and has 27 LDO and 10 buck regulators. > > Cc: devicetree@vger.kernel.org > Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> > Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> > Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> > --- > Documentation/devicetree/bindings/mfd/s2mps11.txt | 23 ++++++++++++++------- > 1 file changed, 15 insertions(+), 8 deletions(-) Nothing to controversial here. For my own reference: Acked-by: Lee Jones <lee.jones@linaro.org> > diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt > index 890f0b0e1643..c0427c9d0886 100644 > --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt > +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt > @@ -1,5 +1,5 @@ > > -* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator > +* Samsung S2MPS11/13/14/15 and S2MPU02 Voltage and Current Regulator > > The Samsung S2MPS11 is a multi-function device which includes voltage and > current regulators, RTC, charger controller and other sub-blocks. It is > @@ -7,8 +7,12 @@ interfaced to the host controller using an I2C interface. Each sub-block is > addressed by the host system using different I2C slave addresses. > > Required properties: > -- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" > - or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". > +- compatible: Should be one of the following > + - "samsung,s2mps11-pmic" > + - "samsung,s2mps13-pmic" > + - "samsung,s2mps14-pmic" > + - "samsung,s2mps15-pmic" > + - "samsung,s2mpu02-pmic". > - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. > > Optional properties: > @@ -24,7 +28,7 @@ Optional properties: > unwanted buck warm reset (setting buck voltages to default values). > > Optional nodes: > -- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 > +- clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768 > KHz outputs, so to register these as clocks with common clock framework > instantiate a sub-node named "clocks". It uses the common clock binding > documented in : > @@ -37,12 +41,13 @@ Optional nodes: > the clock which they consume. > Clock ID Devices > ---------------------------------------------------------- > - 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 > - 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 > - 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 > + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 > + 32KhzCP 1 S2MPS11, S2MPS13, S2MPS15, S5M8767 > + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 > > - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", > - "samsung,s2mps14-clk", "samsung,s5m8767-clk" > + "samsung,s2mps14-clk", "samsung,s2mps15-clk", > + "samsung,s5m8767-clk" > > - regulators: The regulators of s2mps11 that have to be instantiated should be > included in a sub-node named 'regulators'. Regulator nodes included in this > @@ -90,6 +95,7 @@ as per the datasheet of s2mps11. > - S2MPS11: 1 to 38 > - S2MPS13: 1 to 40 > - S2MPS14: 1 to 25 > + - S2MPS15: 1 to 27 > - S2MPU02: 1 to 28 > - Example: LDO1, LDO2, LDO28 > - BUCKn > @@ -97,6 +103,7 @@ as per the datasheet of s2mps11. > - S2MPS11: 1 to 10 > - S2MPS13: 1 to 10 > - S2MPS14: 1 to 5 > + - S2MPS15: 1 to 10 > - S2MPU02: 1 to 7 > - Example: BUCK1, BUCK2, BUCK9 > -- Lee Jones Linaro STMicroelectronics Landing Team Lead Linaro.org │ Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v2 1/5] dt-bindings: mfd: s2mps11: add documentation for s2mps15 PMIC 2015-10-26 11:09 ` Lee Jones @ 2015-10-26 12:42 ` Alim Akhtar 0 siblings, 0 replies; 3+ messages in thread From: Alim Akhtar @ 2015-10-26 12:42 UTC (permalink / raw) To: Lee Jones Cc: broonie, k.kozlowski, mturquette, linux-samsung-soc, linux-clk, rtc-linux, linux-kernel, Thomas Abraham, devicetree On 10/26/2015 04:39 PM, Lee Jones wrote: > On Mon, 26 Oct 2015, Alim Akhtar wrote: > >> From: Thomas Abraham <thomas.ab@samsung.com> >> >> Add dt-binding documentation for s2mps15 PMIC device. The s2mps15 device >> is similar to s2mps11/14 PMIC device and has 27 LDO and 10 buck regulators. >> >> Cc: devicetree@vger.kernel.org >> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> >> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> >> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> >> --- >> Documentation/devicetree/bindings/mfd/s2mps11.txt | 23 ++++++++++++++------- >> 1 file changed, 15 insertions(+), 8 deletions(-) > > Nothing to controversial here. > > For my own reference: > Acked-by: Lee Jones <lee.jones@linaro.org> > Thanks, will send v3 of this series. >> diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt >> index 890f0b0e1643..c0427c9d0886 100644 >> --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt >> +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt >> @@ -1,5 +1,5 @@ >> >> -* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator >> +* Samsung S2MPS11/13/14/15 and S2MPU02 Voltage and Current Regulator >> >> The Samsung S2MPS11 is a multi-function device which includes voltage and >> current regulators, RTC, charger controller and other sub-blocks. It is >> @@ -7,8 +7,12 @@ interfaced to the host controller using an I2C interface. Each sub-block is >> addressed by the host system using different I2C slave addresses. >> >> Required properties: >> -- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" >> - or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". >> +- compatible: Should be one of the following >> + - "samsung,s2mps11-pmic" >> + - "samsung,s2mps13-pmic" >> + - "samsung,s2mps14-pmic" >> + - "samsung,s2mps15-pmic" >> + - "samsung,s2mpu02-pmic". >> - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. >> >> Optional properties: >> @@ -24,7 +28,7 @@ Optional properties: >> unwanted buck warm reset (setting buck voltages to default values). >> >> Optional nodes: >> -- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 >> +- clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768 >> KHz outputs, so to register these as clocks with common clock framework >> instantiate a sub-node named "clocks". It uses the common clock binding >> documented in : >> @@ -37,12 +41,13 @@ Optional nodes: >> the clock which they consume. >> Clock ID Devices >> ---------------------------------------------------------- >> - 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 >> - 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 >> - 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 >> + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 >> + 32KhzCP 1 S2MPS11, S2MPS13, S2MPS15, S5M8767 >> + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 >> >> - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", >> - "samsung,s2mps14-clk", "samsung,s5m8767-clk" >> + "samsung,s2mps14-clk", "samsung,s2mps15-clk", >> + "samsung,s5m8767-clk" >> >> - regulators: The regulators of s2mps11 that have to be instantiated should be >> included in a sub-node named 'regulators'. Regulator nodes included in this >> @@ -90,6 +95,7 @@ as per the datasheet of s2mps11. >> - S2MPS11: 1 to 38 >> - S2MPS13: 1 to 40 >> - S2MPS14: 1 to 25 >> + - S2MPS15: 1 to 27 >> - S2MPU02: 1 to 28 >> - Example: LDO1, LDO2, LDO28 >> - BUCKn >> @@ -97,6 +103,7 @@ as per the datasheet of s2mps11. >> - S2MPS11: 1 to 10 >> - S2MPS13: 1 to 10 >> - S2MPS14: 1 to 5 >> + - S2MPS15: 1 to 10 >> - S2MPU02: 1 to 7 >> - Example: BUCK1, BUCK2, BUCK9 >> > ^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2015-10-26 12:42 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1445855803-26973-1-git-send-email-alim.akhtar@samsung.com>
2015-10-26 10:36 ` [PATCH v2 1/5] dt-bindings: mfd: s2mps11: add documentation for s2mps15 PMIC Alim Akhtar
2015-10-26 11:09 ` Lee Jones
2015-10-26 12:42 ` Alim Akhtar
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).