From mboxrd@z Thu Jan 1 00:00:00 1970 From: Rob Herring Subject: Re: [PATCH 1/3] [media] mt9v032: Add reset and standby gpios Date: Fri, 6 Nov 2015 14:28:40 -0600 Message-ID: <20151106202840.GA19748@rob-hp-laptop> References: <1446815625-18413-1-git-send-email-mpa@pengutronix.de> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Return-path: Content-Disposition: inline In-Reply-To: <1446815625-18413-1-git-send-email-mpa@pengutronix.de> Sender: linux-media-owner@vger.kernel.org To: Markus Pargmann Cc: Laurent Pinchart , Hans Verkuil , Philipp Zabel , devicetree@vger.kernel.org, linux-media@vger.kernel.org List-Id: devicetree@vger.kernel.org On Fri, Nov 06, 2015 at 02:13:43PM +0100, Markus Pargmann wrote: > Add optional reset and standby gpios. The reset gpio is used to reset > the chip in power_on(). > > The standby gpio is not used currently. It is just unset, so the chip is > not in standby. > > Signed-off-by: Markus Pargmann > Reviewed-by: Philipp Zabel > --- > .../devicetree/bindings/media/i2c/mt9v032.txt | 2 ++ Acked-by: Rob Herring > drivers/media/i2c/mt9v032.c | 23 ++++++++++++++++++++++ > 2 files changed, 25 insertions(+) > > diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt > index 202565313e82..100f0ae43269 100644 > --- a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt > +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt > @@ -20,6 +20,8 @@ Optional Properties: > > - link-frequencies: List of allowed link frequencies in Hz. Each frequency is > expressed as a 64-bit big-endian integer. > +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. > +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. > > For further reading on port node refer to > Documentation/devicetree/bindings/media/video-interfaces.txt. > diff --git a/drivers/media/i2c/mt9v032.c b/drivers/media/i2c/mt9v032.c > index a68ce94ee097..4aefde9634f5 100644 > --- a/drivers/media/i2c/mt9v032.c > +++ b/drivers/media/i2c/mt9v032.c > @@ -24,6 +24,7 @@ > #include > #include > #include > +#include > > #include > #include > @@ -251,6 +252,8 @@ struct mt9v032 { > > struct regmap *regmap; > struct clk *clk; > + struct gpio_desc *reset_gpio; > + struct gpio_desc *standby_gpio; > > struct mt9v032_platform_data *pdata; > const struct mt9v032_model_info *model; > @@ -312,16 +315,26 @@ static int mt9v032_power_on(struct mt9v032 *mt9v032) > struct regmap *map = mt9v032->regmap; > int ret; > > + gpiod_set_value_cansleep(mt9v032->reset_gpio, 1); > + > ret = clk_set_rate(mt9v032->clk, mt9v032->sysclk); > if (ret < 0) > return ret; > > + /* system clock has to be enabled before releasing the reset */ > ret = clk_prepare_enable(mt9v032->clk); > if (ret) > return ret; > > udelay(1); > > + gpiod_set_value_cansleep(mt9v032->reset_gpio, 0); > + > + /* > + * After releasing reset, it can take up to 1us until the chip is done > + */ > + udelay(1); > + > /* Reset the chip and stop data read out */ > ret = regmap_write(map, MT9V032_RESET, 1); > if (ret < 0) > @@ -954,6 +967,16 @@ static int mt9v032_probe(struct i2c_client *client, > if (IS_ERR(mt9v032->clk)) > return PTR_ERR(mt9v032->clk); > > + mt9v032->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset", > + GPIOD_OUT_HIGH); > + if (IS_ERR(mt9v032->reset_gpio)) > + return PTR_ERR(mt9v032->reset_gpio); > + > + mt9v032->standby_gpio = devm_gpiod_get_optional(&client->dev, "standby", > + GPIOD_OUT_LOW); > + if (IS_ERR(mt9v032->standby_gpio)) > + return PTR_ERR(mt9v032->standby_gpio); > + > mutex_init(&mt9v032->power_lock); > mt9v032->pdata = pdata; > mt9v032->model = (const void *)did->driver_data; > -- > 2.6.1 > > -- > To unsubscribe from this list: send the line "unsubscribe devicetree" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html