Re: [PATCH linux-next 1/2] irqchip: Add brcm,bcm6345-l1-intc device tree binding

[Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>]

On Wed, Dec 09, 2015 at 08:27:09PM +0000, Simon Arlott wrote:
> Add device tree binding for the BCM6345 interrupt controller.
> 
> This controller is similar to the SMP-capable BCM7038 and
> the BCM3380 but with packed interrupt registers.
> 
> Signed-off-by: Simon Arlott <simon-A6De1vDTPLDsq35pWSNszA@public.gmane.org>

Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>

> ---
> Corrected example device name to be "interrupt-controller".
> 
>  .../interrupt-controller/brcm,bcm6345-l1-intc.txt  | 57 ++++++++++++++++++++++
>  1 file changed, 57 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt
> 
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt
> new file mode 100644
> index 0000000..4040905
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt
> @@ -0,0 +1,57 @@
> +Broadcom BCM6345-style Level 1 interrupt controller
> +
> +This block is a first level interrupt controller that is typically connected
> +directly to one of the HW INT lines on each CPU.
> +
> +Key elements of the hardware design include:
> +
> +- 32, 64 or 128 incoming level IRQ lines
> +
> +- Most onchip peripherals are wired directly to an L1 input
> +
> +- A separate instance of the register set for each CPU, allowing individual
> +  peripheral IRQs to be routed to any CPU
> +
> +- Contains one or more enable/status word pairs per CPU
> +
> +- No atomic set/clear operations
> +
> +- No polarity/level/edge settings
> +
> +- No FIFO or priority encoder logic; software is expected to read all
> +  2-4 status words to determine which IRQs are pending
> +
> +Required properties:
> +
> +- compatible: should be "brcm,bcm<soc>-l1-intc", "brcm,bcm6345-l1-intc"
> +- reg: specifies the base physical address and size of the registers;
> +  the number of supported IRQs is inferred from the size argument
> +- interrupt-controller: identifies the node as an interrupt controller
> +- #interrupt-cells: specifies the number of cells needed to encode an interrupt
> +  source, should be 1.
> +- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
> +  this one is cascaded from
> +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
> +  node; valid values depend on the type of parent interrupt controller
> +
> +If multiple reg ranges and interrupt-parent entries are present on an SMP
> +system, the driver will allow IRQ SMP affinity to be set up through the
> +/proc/irq/ interface.  In the simplest possible configuration, only one
> +reg range and one interrupt-parent is needed.
> +
> +The driver operates in native CPU endian by default, there is no support for
> +specifying an alternative endianness.
> +
> +Example:
> +
> +periph_intc: interrupt-controller@10000000 {
> +        compatible = "brcm,bcm63168-l1-intc", "brcm,bcm6345-l1-intc";
> +        reg = <0x10000020 0x20>,
> +              <0x10000040 0x20>;
> +
> +        interrupt-controller;
> +        #interrupt-cells = <1>;
> +
> +        interrupt-parent = <&cpu_intc>;
> +        interrupts = <2>, <3>;
> +};
> -- 
> 2.1.4
> 
> -- 
> Simon Arlott
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html