* [PATCH 2/2] dt-bindings: pinctrl: Add MDM9615 TLMM bindings
[not found] <1466158535-17962-1-git-send-email-narmstrong@baylibre.com>
@ 2016-06-17 10:15 ` Neil Armstrong
2016-06-20 16:19 ` Rob Herring
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Neil Armstrong @ 2016-06-17 10:15 UTC (permalink / raw)
To: linus.walleij, andy.gross, sricharan
Cc: Neil Armstrong, linux-gpio, linux-arm-msm, linux-soc,
linux-kernel, devicetree
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../bindings/pinctrl/qcom,mdm9615-pinctrl.txt | 152 +++++++++++++++++++++
1 file changed, 152 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt
new file mode 100644
index 0000000..1b52f01
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt
@@ -0,0 +1,152 @@
+Qualcomm MDM9615 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MDM9615 platform.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be "qcom,mdm9615-pinctrl"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode. Valid pins are:
+ gpio0-gpio87
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins.
+ Valid values are:
+ gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart,
+ sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio,
+ cdc_mclk
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull up.
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+
+- drive-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the drive strength for the specified pins, in mA.
+ Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+ msmgpio: pinctrl@800000 {
+ compatible = "qcom,mdm9615-pinctrl";
+ reg = <0x800000 0x4000>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <0 16 0x4>;
+
+ gsbi8_uart: gsbi8-uart {
+ mux {
+ pins = "gpio34", "gpio35";
+ function = "gsbi8";
+ };
+
+ tx {
+ pins = "gpio34";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio35";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+ };
--
1.9.1
^ permalink raw reply related [flat|nested] 4+ messages in thread