* [PATCH 1/3] ARM: BCM5301X: Add separated DTS include file for BCM47094
@ 2016-09-21 20:58 Rafał Miłecki
2016-09-21 20:58 ` [PATCH 2/3] ARM: BCM5301X: Enable UART on Netgear R8000 Rafał Miłecki
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Rafał Miłecki @ 2016-09-21 20:58 UTC (permalink / raw)
To: Florian Fainelli
Cc: Rafał Miłecki, Hauke Mehrtens, Rafał Miłecki,
maintainer:BROADCOM BCM5301X ARM ARCHITECTURE, Rob Herring,
Mark Rutland, Russell King,
open list:BROADCOM BCM5301X ARM ARCHITECTURE,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list
From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
Use it to store BCM47094 specific properties/values and avoid repeating
them in device DTS files.
Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
---
arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 3 +--
arch/arm/boot/dts/bcm47094-netgear-r8500.dts | 3 +--
arch/arm/boot/dts/bcm47094.dtsi | 11 +++++++++++
3 files changed, 13 insertions(+), 4 deletions(-)
create mode 100644 arch/arm/boot/dts/bcm47094.dtsi
diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
index c8c0b36..661348d 100644
--- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
@@ -9,7 +9,7 @@
/dts-v1/;
-#include "bcm4708.dtsi"
+#include "bcm47094.dtsi"
#include "bcm5301x-nand-cs0-bch1.dtsi"
/ {
@@ -107,7 +107,6 @@
&uart0 {
status = "okay";
- clock-frequency = <125000000>;
};
&usb3 {
diff --git a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
index 10db4f8..521b415 100644
--- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
+++ b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
@@ -6,7 +6,7 @@
/dts-v1/;
-#include "bcm4708.dtsi"
+#include "bcm47094.dtsi"
#include "bcm5301x-nand-cs0-bch8.dtsi"
/ {
@@ -100,5 +100,4 @@
&uart0 {
status = "okay";
- clock-frequency = <125000000>;
};
diff --git a/arch/arm/boot/dts/bcm47094.dtsi b/arch/arm/boot/dts/bcm47094.dtsi
new file mode 100644
index 0000000..f039765
--- /dev/null
+++ b/arch/arm/boot/dts/bcm47094.dtsi
@@ -0,0 +1,11 @@
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
+ *
+ * Licensed under the ISC license.
+ */
+
+#include "bcm4708.dtsi"
+
+&uart0 {
+ clock-frequency = <125000000>;
+};
--
2.9.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH 2/3] ARM: BCM5301X: Enable UART on Netgear R8000
2016-09-21 20:58 [PATCH 1/3] ARM: BCM5301X: Add separated DTS include file for BCM47094 Rafał Miłecki
@ 2016-09-21 20:58 ` Rafał Miłecki
2016-09-21 20:58 ` [PATCH 3/3] ARM: BCM5301X: Specify USB 3.0 PHY in DT Rafał Miłecki
[not found] ` <20160921205838.15627-1-zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2 siblings, 0 replies; 4+ messages in thread
From: Rafał Miłecki @ 2016-09-21 20:58 UTC (permalink / raw)
To: Florian Fainelli
Cc: Rafał Miłecki, Hauke Mehrtens, Rafał Miłecki,
maintainer:BROADCOM BCM5301X ARM ARCHITECTURE, Rob Herring,
Mark Rutland, Russell King,
open list:BROADCOM BCM5301X ARM ARCHITECTURE,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list
From: Rafał Miłecki <rafal@milecki.pl>
It was tested by LEDE users, all we need is to adjust clock frequency.
While we're at it create a separated DTS include file to share code with
other BCM4709 devices easier.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
---
arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts | 2 +-
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts | 2 +-
arch/arm/boot/dts/bcm4709-netgear-r7000.dts | 2 +-
arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 6 +++++-
arch/arm/boot/dts/bcm4709.dtsi | 11 +++++++++++
5 files changed, 19 insertions(+), 4 deletions(-)
create mode 100644 arch/arm/boot/dts/bcm4709.dtsi
diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
index 8ade7de..eac0f52 100644
--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
+++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
@@ -9,7 +9,7 @@
/dts-v1/;
-#include "bcm4708.dtsi"
+#include "bcm4709.dtsi"
#include "bcm5301x-nand-cs0-bch8.dtsi"
/ {
diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
index 0653e7e..aab39c9 100644
--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
+++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
@@ -9,7 +9,7 @@
/dts-v1/;
-#include "bcm4708.dtsi"
+#include "bcm4709.dtsi"
#include "bcm5301x-nand-cs0-bch8.dtsi"
/ {
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
index a22ed14..fd38d2a 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
+++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
@@ -9,7 +9,7 @@
/dts-v1/;
-#include "bcm4708.dtsi"
+#include "bcm4709.dtsi"
#include "bcm5301x-nand-cs0-bch8.dtsi"
/ {
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
index ca18151..92f8a72 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
+++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
@@ -9,7 +9,7 @@
/dts-v1/;
-#include "bcm4708.dtsi"
+#include "bcm4709.dtsi"
#include "bcm5301x-nand-cs0-bch8.dtsi"
/ {
@@ -107,6 +107,10 @@
};
};
+&uart0 {
+ status = "okay";
+};
+
&usb2 {
vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
};
diff --git a/arch/arm/boot/dts/bcm4709.dtsi b/arch/arm/boot/dts/bcm4709.dtsi
new file mode 100644
index 0000000..f039765
--- /dev/null
+++ b/arch/arm/boot/dts/bcm4709.dtsi
@@ -0,0 +1,11 @@
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ *
+ * Licensed under the ISC license.
+ */
+
+#include "bcm4708.dtsi"
+
+&uart0 {
+ clock-frequency = <125000000>;
+};
--
2.9.3
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH 3/3] ARM: BCM5301X: Specify USB 3.0 PHY in DT
2016-09-21 20:58 [PATCH 1/3] ARM: BCM5301X: Add separated DTS include file for BCM47094 Rafał Miłecki
2016-09-21 20:58 ` [PATCH 2/3] ARM: BCM5301X: Enable UART on Netgear R8000 Rafał Miłecki
@ 2016-09-21 20:58 ` Rafał Miłecki
[not found] ` <20160921205838.15627-1-zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2 siblings, 0 replies; 4+ messages in thread
From: Rafał Miłecki @ 2016-09-21 20:58 UTC (permalink / raw)
To: Florian Fainelli
Cc: Rafał Miłecki, Hauke Mehrtens, Rafał Miłecki,
maintainer:BROADCOM BCM5301X ARM ARCHITECTURE, Rob Herring,
Mark Rutland, Russell King,
open list:BROADCOM BCM5301X ARM ARCHITECTURE,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list
From: Rafał Miłecki <rafal@milecki.pl>
Driver for Northstar USB 3.0 PHY has been recently added under the name
phy-bcm-ns-usb3. Add binding for it into the DT files.
The only slightly tricky part is BCM47094 which uses different PHY
version and requires different compatible value.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
---
arch/arm/boot/dts/bcm47094.dtsi | 6 ++++++
arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++
2 files changed, 13 insertions(+)
diff --git a/arch/arm/boot/dts/bcm47094.dtsi b/arch/arm/boot/dts/bcm47094.dtsi
index f039765..4f09aa0 100644
--- a/arch/arm/boot/dts/bcm47094.dtsi
+++ b/arch/arm/boot/dts/bcm47094.dtsi
@@ -6,6 +6,12 @@
#include "bcm4708.dtsi"
+/ {
+ usb3_phy: usb3-phy {
+ compatible = "brcm,ns-bx-usb3-phy";
+ };
+};
+
&uart0 {
clock-frequency = <125000000>;
};
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index ae4b388..f09a2bb 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -149,6 +149,13 @@
clock-names = "phy-ref-clk";
};
+ usb3_phy: usb3-phy {
+ compatible = "brcm,ns-ax-usb3-phy";
+ reg = <0x18105000 0x1000>, <0x18003000 0x1000>;
+ reg-names = "dmp", "ccb-mii";
+ #phy-cells = <0>;
+ };
+
axi@18000000 {
compatible = "brcm,bus-axi";
reg = <0x18000000 0x1000>;
--
2.9.3
^ permalink raw reply related [flat|nested] 4+ messages in thread[parent not found: <20160921205838.15627-1-zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>]
* Re: [PATCH 1/3] ARM: BCM5301X: Add separated DTS include file for BCM47094
[not found] ` <20160921205838.15627-1-zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
@ 2016-09-30 19:00 ` Florian Fainelli
0 siblings, 0 replies; 4+ messages in thread
From: Florian Fainelli @ 2016-09-30 19:00 UTC (permalink / raw)
To: Rafał Miłecki, Florian Fainelli
Cc: Rafał Miłecki, Hauke Mehrtens,
maintainer:BROADCOM BCM5301X ARM ARCHITECTURE, Rob Herring,
Mark Rutland, Russell King,
open list:BROADCOM BCM5301X ARM ARCHITECTURE,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list
On 09/21/2016 01:58 PM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>
> Use it to store BCM47094 specific properties/values and avoid repeating
> them in device DTS files.
Series applied, thanks!
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2016-09-30 19:00 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-09-21 20:58 [PATCH 1/3] ARM: BCM5301X: Add separated DTS include file for BCM47094 Rafał Miłecki
2016-09-21 20:58 ` [PATCH 2/3] ARM: BCM5301X: Enable UART on Netgear R8000 Rafał Miłecki
2016-09-21 20:58 ` [PATCH 3/3] ARM: BCM5301X: Specify USB 3.0 PHY in DT Rafał Miłecki
[not found] ` <20160921205838.15627-1-zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2016-09-30 19:00 ` [PATCH 1/3] ARM: BCM5301X: Add separated DTS include file for BCM47094 Florian Fainelli
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).