From mboxrd@z Thu Jan 1 00:00:00 1970 From: Rob Herring Subject: Re: [PATCH 2/4] mfd: ptxpmb-ext-cpld: Add documentation for PTXPMB extended CPLD Date: Mon, 10 Oct 2016 15:10:31 -0500 Message-ID: <20161010201031.GA31318@rob-hp-laptop> References: <1475853574-22339-1-git-send-email-pantelis.antoniou@konsulko.com> <1475853574-22339-3-git-send-email-pantelis.antoniou@konsulko.com> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Return-path: Content-Disposition: inline In-Reply-To: <1475853574-22339-3-git-send-email-pantelis.antoniou@konsulko.com> List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: "linux-mtd" Errors-To: linux-mtd-bounces+gldm-linux-mtd-36=gmane.org@lists.infradead.org To: Pantelis Antoniou Cc: Mark Rutland , Alexandre Courbot , linux-watchdog@vger.kernel.org, devicetree@vger.kernel.org, Frank Rowand , Linus Walleij , linux-kernel@vger.kernel.org, JawaharBalaji Thirumalaisamy , linux-gpio@vger.kernel.org, linux-mtd@lists.infradead.org, linux-i2c@vger.kernel.org, netdev@vger.kernel.org, Georgi Vlaev , Lee Jones , Guenter Roeck List-Id: devicetree@vger.kernel.org On Fri, Oct 07, 2016 at 06:19:32PM +0300, Pantelis Antoniou wrote: > From: Georgi Vlaev > > Add DT bindings document for the PTXPMB extended CPLD device. > > Signed-off-by: Georgi Vlaev > [Ported from Juniper kernel] > Signed-off-by: Pantelis Antoniou > --- > .../bindings/mfd/jnx-ptxpmb-ext-cpld.txt | 35 ++++++++++++++++++++++ > 1 file changed, 35 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/jnx-ptxpmb-ext-cpld.txt > > diff --git a/Documentation/devicetree/bindings/mfd/jnx-ptxpmb-ext-cpld.txt b/Documentation/devicetree/bindings/mfd/jnx-ptxpmb-ext-cpld.txt > new file mode 100644 > index 0000000..098a548a > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/jnx-ptxpmb-ext-cpld.txt > @@ -0,0 +1,35 @@ > +* Device tree bindings for Juniper's PTXPMB Extended CPLD FPGA MFD driver > + > +The device supports a gpio block which is described in the > +jnx-gpio-ptxpmb-ext-cpld document. > + > +Required properties: > + > +- compatible: "jnx,ptxpmb-ext-cpld" > + > +- reg: contains offset/length value for device state control > + registers space. > + > +Optional properties: > + > +- interrupts: The interrupt line(s) the /IRQ signal(s) for the device is > + connected to. > + > +- interrupt-parent: The parent interrupt controller. > + > +Example: > + > +ext-cpld@1,0 { > + compatible = "jnx,ptxpmb-ext-cpld"; > + reg = <0x1 0 0x1000>; What's the bus type here? Unit address is probably wrong. > + interrupt-parent = <&mpic>; > + interrupts = <7 2>, <8 2>; > + > + gpio_ext_cpld: cpld-ext-gpio { > + compatible = "jnx,gpio-ptxpmb-ext-cpld"; > + #gpio-cells = <2>; > + #interrupt-cells = <2>; > + gpio-controller; > + interrupt-controller; > + }; > +}; > -- > 1.9.1 > ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/