[PATCH 2/5] arm: mvebu: support for SMP on 98DX3336 SoC

[PATCH 2/5] arm: mvebu: support for SMP on 98DX3336 SoC

[Chris Packham]

Compared to the armada-xp the 98DX3336 uses different registers to set
the boot address for the secondary CPU so a new enable-method is needed.
This will only work if the machine definition doesn't define an overall
smp_ops because there is not currently a way of overriding this from the
device tree if it is set in the machine definition.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 .../bindings/arm/marvell/98dx3236-resume-ctrl.txt  | 18 ++++++
 arch/arm/mach-mvebu/Makefile                       |  1 +
 arch/arm/mach-mvebu/common.h                       |  1 +
 arch/arm/mach-mvebu/platsmp.c                      | 43 ++++++++++++++
 arch/arm/mach-mvebu/pmsu-98dx3236.c                | 69 ++++++++++++++++++++++
 5 files changed, 132 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
 create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c

diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
new file mode 100644
index 000000000000..8082ba872edd
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
@@ -0,0 +1,18 @@
+Resume Control
+--------------
+Available on Marvell SOCs: 98DX3336 and 98DX4251
+
+Required properties:
+
+- compatible: must be "marvell,98dx3336-resume-ctrl"
+
+- reg: Should contain resume control registers location and length
+
+Example:
+
+resume@20980 {
+	compatible = "marvell,98dx3336-resume-ctrl";
+	reg = <0x20980 0x10>;
+};
+
+
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index 6c6497e80a7b..2a2dd8324fb8 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_MACH_MVEBU_ANY)	 += system-controller.o mvebu-soc-id.o
 
 ifeq ($(CONFIG_MACH_MVEBU_V7),y)
 obj-y				 += cpu-reset.o board-v7.o coherency.o coherency_ll.o pmsu.o pmsu_ll.o
+obj-y				 += pmsu-98dx3236.o
 
 obj-$(CONFIG_PM)		 += pm.o pm-board.o
 obj-$(CONFIG_SMP)		 += platsmp.o headsmp.o platsmp-a9.o headsmp-a9.o
diff --git a/arch/arm/mach-mvebu/common.h b/arch/arm/mach-mvebu/common.h
index 6b775492cfad..099dabf23461 100644
--- a/arch/arm/mach-mvebu/common.h
+++ b/arch/arm/mach-mvebu/common.h
@@ -27,4 +27,5 @@ void __iomem *mvebu_get_scu_base(void);
 
 int mvebu_pm_suspend_init(void (*board_pm_enter)(void __iomem *sdram_reg,
 							u32 srcmd));
+void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr);
 #endif
diff --git a/arch/arm/mach-mvebu/platsmp.c b/arch/arm/mach-mvebu/platsmp.c
index 46c742d3bd41..3c9ab9a008ad 100644
--- a/arch/arm/mach-mvebu/platsmp.c
+++ b/arch/arm/mach-mvebu/platsmp.c
@@ -182,5 +182,48 @@ const struct smp_operations armada_xp_smp_ops __initconst = {
 #endif
 };
 
+static int mv98dx3236_boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+	int ret, hw_cpu;
+
+	pr_info("Booting CPU %d\n", cpu);
+
+	hw_cpu = cpu_logical_map(cpu);
+	set_secondary_cpu_clock(hw_cpu);
+	mv98dx3236_resume_set_cpu_boot_addr(hw_cpu,
+					    armada_xp_secondary_startup);
+
+	/*
+	 * This is needed to wake up CPUs in the offline state after
+	 * using CPU hotplug.
+	 */
+	arch_send_wakeup_ipi_mask(cpumask_of(cpu));
+
+	/*
+	 * This is needed to take secondary CPUs out of reset on the
+	 * initial boot.
+	 */
+	ret = mvebu_cpu_reset_deassert(hw_cpu);
+	if (ret) {
+		pr_warn("unable to boot CPU: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+struct smp_operations mv98dx3236_smp_ops __initdata = {
+	.smp_init_cpus		= armada_xp_smp_init_cpus,
+	.smp_prepare_cpus	= armada_xp_smp_prepare_cpus,
+	.smp_boot_secondary	= mv98dx3236_boot_secondary,
+	.smp_secondary_init     = armada_xp_secondary_init,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_die		= armada_xp_cpu_die,
+	.cpu_kill               = armada_xp_cpu_kill,
+#endif
+};
+
 CPU_METHOD_OF_DECLARE(armada_xp_smp, "marvell,armada-xp-smp",
 		      &armada_xp_smp_ops);
+CPU_METHOD_OF_DECLARE(mv98dx3236_smp, "marvell,98dx3236-smp",
+		      &mv98dx3236_smp_ops);
diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c b/arch/arm/mach-mvebu/pmsu-98dx3236.c
new file mode 100644
index 000000000000..fadc81d0c051
--- /dev/null
+++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
@@ -0,0 +1,69 @@
+/**
+ * CPU resume support for 98DX4521 internal CPU (a.k.a. MSYS).
+ */
+
+#define pr_fmt(fmt) "mv98dx3236-resume: " fmt
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+#include "common.h"
+
+static void __iomem *mv98dx3236_resume_base;
+#define MV98DX3236_CPU_RESUME_CTRL_OFFSET	0x08
+#define MV98DX3236_CPU_RESUME_ADDR_OFFSET	0x04
+
+static const struct of_device_id of_mv98dx3236_resume_table[] = {
+	{.compatible = "marvell,98dx3336-resume-ctrl",},
+	{ /* end of list */ },
+};
+
+void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr)
+{
+	WARN_ON(hw_cpu != 1);
+
+	writel(0, mv98dx3236_resume_base + MV98DX3236_CPU_RESUME_CTRL_OFFSET);
+	writel(virt_to_phys(boot_addr), mv98dx3236_resume_base +
+	       MV98DX3236_CPU_RESUME_ADDR_OFFSET);
+}
+
+static int __init mv98dx3236_resume_init(void)
+{
+	struct device_node *np;
+	struct resource res;
+	int ret = 0;
+
+	np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
+	if (!np)
+		return 0;
+
+	pr_info("Initializing 98DX4521 Resume\n");
+
+	if (of_address_to_resource(np, 0, &res)) {
+		pr_err("unable to get resource\n");
+		ret = -ENOENT;
+		goto out;
+	}
+
+	if (!request_mem_region(res.start, resource_size(&res),
+				np->full_name)) {
+		pr_err("unable to request region\n");
+		ret = -EBUSY;
+		goto out;
+	}
+
+	mv98dx3236_resume_base = ioremap(res.start, resource_size(&res));
+	if (!mv98dx3236_resume_base) {
+		pr_err("unable to map registers\n");
+		release_mem_region(res.start, resource_size(&res));
+		ret = -ENOMEM;
+		goto out;
+	}
+
+out:
+	of_node_put(np);
+	return ret;
+}
+
+early_initcall(mv98dx3236_resume_init);
-- 
2.11.0.24.ge6920cf

Re: [PATCH 2/5] arm: mvebu: support for SMP on 98DX3336 SoC

[Rob Herring]

On Thu, Dec 22, 2016 at 05:13:25PM +1300, Chris Packham wrote:
> Compared to the armada-xp the 98DX3336 uses different registers to set
> the boot address for the secondary CPU so a new enable-method is needed.
> This will only work if the machine definition doesn't define an overall
> smp_ops because there is not currently a way of overriding this from the
> device tree if it is set in the machine definition.

Doesn't look like you documented the enable-method value.

> Signed-off-by: Chris Packham <chris.packham-6g8wRflRTwXFdCa3tKVlE6U/zSkkHjvu@public.gmane.org>
> ---
>  .../bindings/arm/marvell/98dx3236-resume-ctrl.txt  | 18 ++++++
>  arch/arm/mach-mvebu/Makefile                       |  1 +
>  arch/arm/mach-mvebu/common.h                       |  1 +
>  arch/arm/mach-mvebu/platsmp.c                      | 43 ++++++++++++++
>  arch/arm/mach-mvebu/pmsu-98dx3236.c                | 69 ++++++++++++++++++++++
>  5 files changed, 132 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
>  create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC

[Chris Packham]

From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>

This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
from Marvell.

Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 .../pinctrl/marvell,armada-98dx3236-pinctrl.txt    |  46 +++++++
 drivers/pinctrl/mvebu/pinctrl-armada-xp.c          | 145 +++++++++++++++++++++
 2 files changed, 191 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt

diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
new file mode 100644
index 000000000000..34c1e380adaa
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
@@ -0,0 +1,46 @@
+* Marvell 98dx3236 pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage
+
+Required properties:
+- compatible: "marvell,98dx3236-pinctrl"
+- reg: register specifier of MPP registers
+
+This driver supports all 98dx3236, 98dx3336 and 98dx4251 variants
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, spi0(mosi), dev(ad8)
+mpp1          1        gpio, spi0(miso), dev(ad9)
+mpp2          2        gpio, spi0(sck), dev(ad10)
+mpp3          3        gpio, spi0(cs0), dev(ad11)
+mpp4          4        gpio, spi0(cs1), smi(mdc), dev(cs0)
+mpp5          5        gpio, pex(rsto), dev(bootcs)
+mpp6          6        gpio, dev(a2)
+mpp7          7        gpio, dev(ale0)
+mpp8          8        gpio, dev(ale1)
+mpp9          9        gpio, dev(ready0)
+mpp10         10       gpio, dev(ad12)
+mpp11         11       gpio, uart1(rxd), uart0(cts), dev(ad13)
+mpp12         12       gpio, uart1(txd), uart0(rts), dev(ad14)
+mpp13         13       gpio, intr(out), dev(ad15)
+mpp14         14       gpio, i2c0(sck)
+mpp15         15       gpio, i2c0(sda)
+mpp16         16       gpio, dev(oe)
+mpp17         17       gpio, dev(clk)
+mpp18         18       gpio, uart1(txd)
+mpp19         19       gpio, uart1(rxd), dev(rb)
+mpp20         20       gpio, dev(we)
+mpp21         21       gpio, dev(ad0)
+mpp22         22       gpio, dev(ad1)
+mpp23         23       gpio, dev(ad2)
+mpp24         24       gpio, dev(ad3)
+mpp25         25       gpio, dev(ad4)
+mpp26         26       gpio, dev(ad5)
+mpp27         27       gpio, dev(ad6)
+mpp28         28       gpio, dev(ad7)
+mpp29         29       gpio, dev(a0)
+mpp30         30       gpio, dev(a1)
+mpp31         31       gpio, slv_smi(mdc), smi(mdc), dev(we1)
+mpp32         32       gpio, slv_smi(mdio), smi(mdio), dev(cs1)
diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
index e4ea71a9d985..2586903c59f0 100644
--- a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
+++ b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
@@ -49,6 +49,10 @@ enum armada_xp_variant {
 	V_MV78460	= BIT(2),
 	V_MV78230_PLUS	= (V_MV78230 | V_MV78260 | V_MV78460),
 	V_MV78260_PLUS	= (V_MV78260 | V_MV78460),
+	V_98DX3236	= BIT(3),
+	V_98DX3336	= BIT(4),
+	V_98DX4251	= BIT(5),
+	V_98DX3236_PLUS	= (V_98DX3236 | V_98DX3336 | V_98DX4251),
 };
 
 static struct mvebu_mpp_mode armada_xp_mpp_modes[] = {
@@ -360,6 +364,124 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = {
 		 MPP_VAR_FUNCTION(0x1, "dev", "ad31",       V_MV78260_PLUS)),
 };
 
+static struct mvebu_mpp_mode mv98dx3236_mpp_modes[] = {
+	MPP_MODE(0,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x2, "spi0", "mosi",       V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ad8",         V_98DX3236_PLUS)),
+	MPP_MODE(1,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x2, "spi0", "miso",       V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ad9",         V_98DX3236_PLUS)),
+	MPP_MODE(2,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x2, "spi0", "csk",        V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ad10",        V_98DX3236_PLUS)),
+	MPP_MODE(3,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x2, "spi0", "cs0",        V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ad11",        V_98DX3236_PLUS)),
+	MPP_MODE(4,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x2, "spi0", "cs1",        V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x3, "smi", "mdc",         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "cs0",         V_98DX3236_PLUS)),
+	MPP_MODE(5,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "pex", "rsto",        V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "bootcs0",     V_98DX3236_PLUS)),
+	MPP_MODE(6,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "a2",          V_98DX3236_PLUS)),
+	MPP_MODE(7,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ale0",        V_98DX3236_PLUS)),
+	MPP_MODE(8,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ale1",        V_98DX3236_PLUS)),
+	MPP_MODE(9,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ready0",      V_98DX3236_PLUS)),
+	MPP_MODE(10,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ad12",        V_98DX3236_PLUS)),
+	MPP_MODE(11,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x2, "uart1", "rxd",       V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x3, "uart0", "cts",       V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ad13",        V_98DX3236_PLUS)),
+	MPP_MODE(12,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x2, "uart1", "txd",       V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x3, "uart0", "rts",       V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ad14",        V_98DX3236_PLUS)),
+	MPP_MODE(13,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "intr", "out",        V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "ad15",        V_98DX3236_PLUS)),
+	MPP_MODE(14,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "i2c0", "sck",        V_98DX3236_PLUS)),
+	MPP_MODE(15,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "i2c0", "sda",        V_98DX3236_PLUS)),
+	MPP_MODE(16,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "oe",          V_98DX3236_PLUS)),
+	MPP_MODE(17,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "clkout",      V_98DX3236_PLUS)),
+	MPP_MODE(18,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x3, "uart1", "txd",       V_98DX3236_PLUS)),
+	MPP_MODE(19,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x3, "uart1", "rxd",       V_98DX3236_PLUS)),
+	MPP_MODE(20,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "we0",         V_98DX3236_PLUS)),
+	MPP_MODE(21,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "ad0",         V_98DX3236_PLUS)),
+	MPP_MODE(22,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "ad1",         V_98DX3236_PLUS)),
+	MPP_MODE(23,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "ad2",         V_98DX3236_PLUS)),
+	MPP_MODE(24,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "ad3",         V_98DX3236_PLUS)),
+	MPP_MODE(25,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "ad4",         V_98DX3236_PLUS)),
+	MPP_MODE(26,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "ad5",         V_98DX3236_PLUS)),
+	MPP_MODE(27,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "ad6",         V_98DX3236_PLUS)),
+	MPP_MODE(28,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "ad7",         V_98DX3236_PLUS)),
+	MPP_MODE(29,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "a0",          V_98DX3236_PLUS)),
+	MPP_MODE(30,
+		 MPP_VAR_FUNCTION(0x0, "gpo", NULL,          V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "dev", "a1",          V_98DX3236_PLUS)),
+	MPP_MODE(31,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "slv_smi", "mdc",     V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x3, "smi", "mdc",         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "we1",         V_98DX3236_PLUS)),
+	MPP_MODE(32,
+		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,         V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x1, "slv_smi", "mdio",    V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x3, "smi", "mdio",        V_98DX3236_PLUS),
+		 MPP_VAR_FUNCTION(0x4, "dev", "cs1",         V_98DX3236_PLUS)),
+};
+
 static struct mvebu_pinctrl_soc_info armada_xp_pinctrl_info;
 
 static const struct of_device_id armada_xp_pinctrl_of_match[] = {
@@ -375,6 +497,10 @@ static const struct of_device_id armada_xp_pinctrl_of_match[] = {
 		.compatible = "marvell,mv78460-pinctrl",
 		.data       = (void *) V_MV78460,
 	},
+	{
+		.compatible = "marvell,98dx3236-pinctrl",
+		.data       = (void *) V_98DX3236,
+	},
 	{ },
 };
 
@@ -407,6 +533,14 @@ static struct pinctrl_gpio_range mv78460_mpp_gpio_ranges[] = {
 	MPP_GPIO_RANGE(2,  64, 64,  3),
 };
 
+static struct mvebu_mpp_ctrl mv98dx3236_mpp_controls[] = {
+	MPP_FUNC_CTRL(0, 32, NULL, armada_xp_mpp_ctrl),
+};
+
+static struct pinctrl_gpio_range mv98dx3236_mpp_gpio_ranges[] = {
+	MPP_GPIO_RANGE(0,   0,  0, 32),
+};
+
 static int armada_xp_pinctrl_suspend(struct platform_device *pdev,
 				     pm_message_t state)
 {
@@ -488,6 +622,17 @@ static int armada_xp_pinctrl_probe(struct platform_device *pdev)
 		soc->gpioranges = mv78460_mpp_gpio_ranges;
 		soc->ngpioranges = ARRAY_SIZE(mv78460_mpp_gpio_ranges);
 		break;
+	case V_98DX3236:
+	case V_98DX3336:
+	case V_98DX4251:
+		/* fall-through */
+		soc->controls = mv98dx3236_mpp_controls;
+		soc->ncontrols = ARRAY_SIZE(mv98dx3236_mpp_controls);
+		soc->modes = mv98dx3236_mpp_modes;
+		soc->nmodes = mv98dx3236_mpp_controls[0].npins;
+		soc->gpioranges = mv98dx3236_mpp_gpio_ranges;
+		soc->ngpioranges = ARRAY_SIZE(mv98dx3236_mpp_gpio_ranges);
+		break;
 	}
 
 	nregs = DIV_ROUND_UP(soc->nmodes, MVEBU_MPPS_PER_REG);
-- 
2.11.0.24.ge6920cf

Re: [PATCH 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC

[Rob Herring]

On Thu, Dec 22, 2016 at 05:13:26PM +1300, Chris Packham wrote:
> From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
> 
> This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
> from Marvell.
> 
> Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
>  .../pinctrl/marvell,armada-98dx3236-pinctrl.txt    |  46 +++++++

Acked-by: Rob Herring <robh@kernel.org>

>  drivers/pinctrl/mvebu/pinctrl-armada-xp.c          | 145 +++++++++++++++++++++
>  2 files changed, 191 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt

Re: [PATCH 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC

[Linus Walleij]

On Thu, Dec 22, 2016 at 5:13 AM, Chris Packham
<chris.packham@alliedtelesis.co.nz> wrote:

> From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
>
> This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
> from Marvell.
>
> Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>

Looks good to me, Sebastian and/or Thomas P can you ACK this patch?

Yours,
Linus Walleij

[PATCH 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs

[Chris Packham]

The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
with integrated CPUs. They are similar to the Armada XP SoCs but have
different I/O interfaces.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 .../devicetree/bindings/arm/marvell/98dx3236.txt   |  10 +
 arch/arm/boot/dts/armada-xp-98dx3236.dtsi          | 231 +++++++++++++++++++++
 arch/arm/boot/dts/armada-xp-98dx3336.dtsi          |  78 +++++++
 arch/arm/boot/dts/armada-xp-98dx4251.dtsi          |  78 +++++++
 4 files changed, 397 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
 create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
 create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
 create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi

diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
new file mode 100644
index 000000000000..e7dc9b2dd90b
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
@@ -0,0 +1,10 @@
+Marvell 98DX3236, 98DX3336 and 98DX4251 Platforms Device Tree Bindings
+----------------------------------------------------------------------
+
+Boards with a SoC of the Marvell 98DX3236, 98DX3336 and 98DX4251 families
+shall have the following property:
+
+Required root node property:
+
+compatible: one of "marvell,armadaxp-98dx3236", "marvell,armadaxp-98dx3336"
+            or "marvell,armadaxp-98dx4251"
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
new file mode 100644
index 000000000000..bac53f8b44af
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
@@ -0,0 +1,231 @@
+/*
+ * Device Tree Include file for Marvell 98dx3236 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx3236 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp.dtsi"
+
+/ {
+	model = "Marvell 98DX3236 SoC";
+	compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "marvell,98dx3236-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <0>;
+			clocks = <&cpuclk 0>;
+			clock-latency = <1000000>;
+		};
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+			  MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+			  MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+		/*
+		 * 98DX3236 has 1 x1 PCIe unit Gen2.0: One unit can be
+		 */
+		pcie-controller {
+			compatible = "marvell,armada-xp-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000   /* Port 0.0 registers */
+				0x82000000 0x1 0       MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+				0x81000000 0x1 0       MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
+				0x82000000 0x2 0       MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */>;
+
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 58>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+		};
+
+		internal-regs {
+			coreclk: mvebu-sar@18230 {
+				compatible = "marvell,mv98dx3236-core-clock";
+			};
+
+			cpuclk: clock-complex@18700 {
+				compatible = "marvell,mv98dx3236-cpu-clock";
+			};
+
+			corediv-clock@18740 {
+				compatible = "marvell,mv98dx3236-corediv-clock";
+				reg = <0xf8268 0xc>;
+				base = <&dfx>;
+				#clock-cells = <1>;
+				clocks = <&mainpll>;
+				clock-output-names = "nand";
+			};
+
+			xor@60900 {
+				status = "disabled";
+			};
+
+			xor@f0900 {
+				status = "disabled";
+			};
+
+			xor@f0800 {
+				compatible = "marvell,orion-xor";
+				reg = <0xf0800 0x100
+				       0xf0a00 0x100>;
+				clocks = <&gateclk 22>;
+				status = "okay";
+
+				xor10 {
+					interrupts = <51>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor11 {
+					interrupts = <52>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <82>, <83>, <84>, <85>;
+			};
+
+			/* does not exist */
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				status = "disabled";
+			};
+
+			gpio2: gpio@18180 { /* rework some properties */
+				compatible = "marvell,orion-gpio";
+				reg = <0x18180 0x40>;
+				ngpios = <1>; /* only gpio #32 */
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <87>;
+			};
+		};
+
+		dfx-registers {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+
+			dfx: dfx@0 {
+				compatible = "simple-bus";
+				reg = <0 0x100000>;
+			};
+		};
+
+		switch {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
+
+			packet-processor@0 {
+				compatible = "marvell,prestera-98dx3236";
+				reg = <0 0x4000000>;
+				interrupts = <33>, <34>, <35>;
+				dfx = <&dfx>;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	compatible = "marvell,98dx3236-pinctrl";
+
+	spi0_pins: spi0-pins {
+		marvell,pins = "mpp0", "mpp1",
+			       "mpp2", "mpp3";
+		marvell,function = "spi0";
+	};
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
new file mode 100644
index 000000000000..9c9aa565fd82
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
@@ -0,0 +1,78 @@
+/*
+ * Device Tree Include file for Marvell 98dx3336 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx3336 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+	model = "Marvell 98DX3336 SoC";
+	compatible = "marvell,armadaxp-98dx3336", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	cpus {
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <1>;
+			clocks = <&cpuclk 1>;
+			clock-latency = <1000000>;
+		};
+	};
+
+	soc {
+		internal-regs {
+			resume@20980 {
+				compatible = "marvell,98dx3336-resume-ctrl";
+				reg = <0x20980 0x10>;
+			};
+		};
+
+		switch {
+			packet-processor@0 {
+				compatible = "marvell,prestera-98dx3336";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
new file mode 100644
index 000000000000..5d1da8513fae
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
@@ -0,0 +1,78 @@
+/*
+ * Device Tree Include file for Marvell 98dx4521 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx4521 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+	model = "Marvell 98DX4251 SoC";
+	compatible = "marvell,armadaxp-98dx4521", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	cpus {
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <1>;
+			clocks = <&cpuclk 1>;
+			clock-latency = <1000000>;
+		};
+	};
+
+	soc {
+		internal-regs {
+			resume@20980 {
+				compatible = "marvell,98dx3336-resume-ctrl";
+				reg = <0x20980 0x10>;
+			};
+		};
+
+		switch {
+			packet-processor@0 {
+				compatible = "marvell,prestera-98dx4521";
+			};
+		};
+	};
+};
-- 
2.11.0.24.ge6920cf

Re: [PATCH 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs

[Rob Herring]

On Thu, Dec 22, 2016 at 05:13:27PM +1300, Chris Packham wrote:
> The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
> with integrated CPUs. They are similar to the Armada XP SoCs but have
> different I/O interfaces.
> 
> Signed-off-by: Chris Packham <chris.packham-6g8wRflRTwXFdCa3tKVlE6U/zSkkHjvu@public.gmane.org>
> ---
>  .../devicetree/bindings/arm/marvell/98dx3236.txt   |  10 +
>  arch/arm/boot/dts/armada-xp-98dx3236.dtsi          | 231 +++++++++++++++++++++
>  arch/arm/boot/dts/armada-xp-98dx3336.dtsi          |  78 +++++++
>  arch/arm/boot/dts/armada-xp-98dx4251.dtsi          |  78 +++++++
>  4 files changed, 397 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
>  create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
> 
> diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
> new file mode 100644
> index 000000000000..e7dc9b2dd90b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
> @@ -0,0 +1,10 @@
> +Marvell 98DX3236, 98DX3336 and 98DX4251 Platforms Device Tree Bindings
> +----------------------------------------------------------------------
> +
> +Boards with a SoC of the Marvell 98DX3236, 98DX3336 and 98DX4251 families
> +shall have the following property:
> +
> +Required root node property:
> +
> +compatible: one of "marvell,armadaxp-98dx3236", "marvell,armadaxp-98dx3336"
> +            or "marvell,armadaxp-98dx4251"

The 3336 and 4251 are compatible with 3236 according to the dts files. 
That needs to be expressed here.

Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards

[Chris Packham]

These boards are Marvell's evaluation boards for the 98DX4251 and
98DX3336 SoCs.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 arch/arm/boot/dts/db-dxbc2.dts      | 159 ++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++++++++++++++++++++++++
 2 files changed, 314 insertions(+)
 create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
 create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts

diff --git a/arch/arm/boot/dts/db-dxbc2.dts b/arch/arm/boot/dts/db-dxbc2.dts
new file mode 100644
index 000000000000..f56786cea5f8
--- /dev/null
+++ b/arch/arm/boot/dts/db-dxbc2.dts
@@ -0,0 +1,159 @@
+/*
+ * Device Tree file for DB-DXBC2 board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx4251.dtsi"
+
+/ {
+	model = "Marvell Bobcat2 Evaluation Board";
+	compatible = "marvell,db-dxbc2", "marvell,armadaxp-98dx4251", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+			  MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+			  MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+		devbus-bootcs {
+			status = "okay";
+
+			/* Device Bus parameters are required */
+
+			/* Read parameters */
+			devbus,bus-width    = <16>;
+			devbus,turn-off-ps  = <60000>;
+			devbus,badr-skew-ps = <0>;
+			devbus,acc-first-ps = <124000>;
+			devbus,acc-next-ps  = <248000>;
+			devbus,rd-setup-ps  = <0>;
+			devbus,rd-hold-ps   = <0>;
+
+			/* Write parameters */
+			devbus,sync-enable = <0>;
+			devbus,wr-high-ps  = <60000>;
+			devbus,wr-low-ps   = <60000>;
+			devbus,ale-wr-ps   = <60000>;
+		};
+
+		internal-regs {
+			serial@12000 {
+				status = "okay";
+			};
+			serial@12100 {
+				status = "okay";
+			};
+
+			i2c@11000 {
+				clock-frequency = <100000>;
+				status = "okay";
+			};
+
+			mvsdio@d4000 {
+				pinctrl-0 = <&sdio_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				/* No CD or WP GPIOs */
+				broken-cd;
+			};
+
+			nand@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+			};
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p64";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <20000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x00100000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x00100000 0x00040000>;
+			label = "u-boot-env";
+		};
+		partition@unused {
+			reg = <0x00140000 0x00ec0000>;
+			label = "unused";
+		};
+
+	};
+};
diff --git a/arch/arm/boot/dts/db-xc3-24g4xg.dts b/arch/arm/boot/dts/db-xc3-24g4xg.dts
new file mode 100644
index 000000000000..5eb89ffb9a7d
--- /dev/null
+++ b/arch/arm/boot/dts/db-xc3-24g4xg.dts
@@ -0,0 +1,155 @@
+/*
+ * Device Tree file for DB-XC3-24G4XG board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3336.dtsi"
+
+/ {
+	model = "DB-XC3-24G4XG";
+	compatible = "marvell,db-xc3-24g4xg", "marvell,armadaxp-98dx3336", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x40000000>; /* 1 GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+			  MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+			  MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+		devbus-bootcs {
+			status = "okay";
+
+			/* Device Bus parameters are required */
+
+			/* Read parameters */
+			devbus,bus-width    = <16>;
+			devbus,turn-off-ps  = <60000>;
+			devbus,badr-skew-ps = <0>;
+			devbus,acc-first-ps = <124000>;
+			devbus,acc-next-ps  = <248000>;
+			devbus,rd-setup-ps  = <0>;
+			devbus,rd-hold-ps   = <0>;
+
+			/* Write parameters */
+			devbus,sync-enable = <0>;
+			devbus,wr-high-ps  = <60000>;
+			devbus,wr-low-ps   = <60000>;
+			devbus,ale-wr-ps   = <60000>;
+		};
+
+		internal-regs {
+			serial@12000 {
+				status = "okay";
+			};
+			serial@12100 {
+				status = "okay";
+			};
+
+			i2c@11000 {
+				clock-frequency = <100000>;
+				status = "okay";
+			};
+
+			mvsdio@d4000 {
+				status = "disabled";
+			};
+
+			nand@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+			};
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p64";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <20000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x00100000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x00100000 0x00040000>;
+			label = "u-boot-env";
+		};
+		partition@unused {
+			reg = <0x00140000 0x00ec0000>;
+			label = "unused";
+		};
+
+	};
+};
-- 
2.11.0.24.ge6920cf