[PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Jerome Brunet]

This patchset fixes an issue with the OdroidC2 board (DWMAC + RTL8211F).
The platform seems to enter LPI on the Rx path too often while performing
relatively high TX transfer. This eventually break the link (both Tx and
Rx), and require to bring the interface down and up again to get the Rx
path working again.

The root cause of this issue is not fully understood yet but disabling EEE
advertisement on the PHY prevent this feature to be negotiated.
With this change, the link is stable and reliable, with the expected
throughput performance.

The patchset adds options in the generic phy driver to disable EEE
advertisement, through device tree. The way it is done is very similar
to the handling of the max-speed property.

Patch 4 is provided here for testing purpose only. Please don't merge
patch 4, this change will go through the amlogic's tree.

Chnages since V3: [3]
 - Fix signess error reported by kbuild test robot (Thx Julia)

Changes since V2: [2]
 - Rename "eee-advert-disable" to "eee-broken-modes" to make the intended
   purpose of this option clear (flag broken configuration, not a
   configuration option)
 - Add DT bindings constants so the DT configuration is more user friendly
 - Submit to net-next instead of net.

Changes since V1: [1]
 - Disable the advertisement of EEE in the generic code instead of the
   realtek driver.

[1] : http://lkml.kernel.org/r/1479220154-25851-1-git-send-email-jbrunet@baylibre.com
[2] : http://lkml.kernel.org/r/1479742524-30222-1-git-send-email-jbrunet@baylibre.com
[3] : http://lkml.kernel.org/r/1480326409-25419-1-git-send-email-jbrunet@baylibre.com

Jerome Brunet (4):
  net: phy: add an option to disable EEE advertisement
  dt-bindings: net: add EEE capability constants
  dt: bindings: add ethernet phy eee-broken-modes option documentation
  ARM64: dts: meson: odroidc2: disable advertisement EEE for GbE.

 Documentation/devicetree/bindings/net/phy.txt      |  2 +
 .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 14 ++++
 drivers/net/phy/phy.c                              |  3 +
 drivers/net/phy/phy_device.c                       | 80 +++++++++++++++++++---
 include/dt-bindings/net/mdio.h                     | 19 +++++
 include/linux/phy.h                                |  3 +
 6 files changed, 112 insertions(+), 9 deletions(-)
 create mode 100644 include/dt-bindings/net/mdio.h

-- 
2.7.4

[PATCH net-next v4 1/4] net: phy: add an option to disable EEE advertisement

[Jerome Brunet]

This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.

On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.

Signed-off-by: Jerome Brunet <jbrunet-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Tested-by: Yegor Yefremov <yegorslists-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
Tested-by: Andreas Färber <afaerber-l3A5Bk7waGM@public.gmane.org>
Tested-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
---
 drivers/net/phy/phy.c        |  3 ++
 drivers/net/phy/phy_device.c | 80 +++++++++++++++++++++++++++++++++++++++-----
 include/linux/phy.h          |  3 ++
 3 files changed, 77 insertions(+), 9 deletions(-)

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 73adbaa9ac86..a3981cc6448a 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -1396,6 +1396,9 @@ int phy_ethtool_set_eee(struct phy_device *phydev, struct ethtool_eee *data)
 {
 	int val = ethtool_adv_to_mmd_eee_adv_t(data->advertised);
 
+	/* Mask prohibited EEE modes */
+	val &= ~phydev->eee_broken_modes;
+
 	phy_write_mmd_indirect(phydev, MDIO_AN_EEE_ADV, MDIO_MMD_AN, val);
 
 	return 0;
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index ba86c191a13e..cb4aca205cf8 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1121,6 +1121,43 @@ static int genphy_config_advert(struct phy_device *phydev)
 }
 
 /**
+ * genphy_config_eee_advert - disable unwanted eee mode advertisement
+ * @phydev: target phy_device struct
+ *
+ * Description: Writes MDIO_AN_EEE_ADV after disabling unsupported energy
+ *   efficent ethernet modes. Returns 0 if the PHY's advertisement hasn't
+ *   changed, and 1 if it has changed.
+ */
+static int genphy_config_eee_advert(struct phy_device *phydev)
+{
+	int broken = phydev->eee_broken_modes;
+	int old_adv, adv;
+
+	/* Nothing to disable */
+	if (!broken)
+		return 0;
+
+	/* If the following call fails, we assume that EEE is not
+	 * supported by the phy. If we read 0, EEE is not advertised
+	 * In both case, we don't need to continue
+	 */
+	adv = phy_read_mmd_indirect(phydev, MDIO_AN_EEE_ADV, MDIO_MMD_AN);
+	if (adv <= 0)
+		return 0;
+
+	old_adv = adv;
+	adv &= ~broken;
+
+	/* Advertising remains unchanged with the broken mask */
+	if (old_adv == adv)
+		return 0;
+
+	phy_write_mmd_indirect(phydev, MDIO_AN_EEE_ADV, MDIO_MMD_AN, adv);
+
+	return 1;
+}
+
+/**
  * genphy_setup_forced - configures/forces speed/duplex from @phydev
  * @phydev: target phy_device struct
  *
@@ -1178,15 +1215,20 @@ EXPORT_SYMBOL(genphy_restart_aneg);
  */
 int genphy_config_aneg(struct phy_device *phydev)
 {
-	int result;
+	int err, changed;
+
+	changed = genphy_config_eee_advert(phydev);
 
 	if (AUTONEG_ENABLE != phydev->autoneg)
 		return genphy_setup_forced(phydev);
 
-	result = genphy_config_advert(phydev);
-	if (result < 0) /* error */
-		return result;
-	if (result == 0) {
+	err = genphy_config_advert(phydev);
+	if (err < 0) /* error */
+		return err;
+
+	changed |= err;
+
+	if (changed == 0) {
 		/* Advertisement hasn't changed, but maybe aneg was never on to
 		 * begin with?  Or maybe phy was isolated?
 		 */
@@ -1196,16 +1238,16 @@ int genphy_config_aneg(struct phy_device *phydev)
 			return ctl;
 
 		if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE))
-			result = 1; /* do restart aneg */
+			changed = 1; /* do restart aneg */
 	}
 
 	/* Only restart aneg if we are advertising something different
 	 * than we were before.
 	 */
-	if (result > 0)
-		result = genphy_restart_aneg(phydev);
+	if (changed > 0)
+		return genphy_restart_aneg(phydev);
 
-	return result;
+	return 0;
 }
 EXPORT_SYMBOL(genphy_config_aneg);
 
@@ -1563,6 +1605,21 @@ static void of_set_phy_supported(struct phy_device *phydev)
 		__set_phy_supported(phydev, max_speed);
 }
 
+static void of_set_phy_eee_broken(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	u32 broken;
+
+	if (!IS_ENABLED(CONFIG_OF_MDIO))
+		return;
+
+	if (!node)
+		return;
+
+	if (!of_property_read_u32(node, "eee-broken-modes", &broken))
+		phydev->eee_broken_modes = broken;
+}
+
 /**
  * phy_probe - probe and init a PHY device
  * @dev: device to probe and init
@@ -1600,6 +1657,11 @@ static int phy_probe(struct device *dev)
 	of_set_phy_supported(phydev);
 	phydev->advertising = phydev->supported;
 
+	/* Get the EEE modes we want to prohibit. We will ask
+	 * the PHY stop advertising these mode later on
+	 */
+	of_set_phy_eee_broken(phydev);
+
 	/* Set the state to READY by default */
 	phydev->state = PHY_READY;
 
diff --git a/include/linux/phy.h b/include/linux/phy.h
index edde28ce163a..b53177fd38af 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -417,6 +417,9 @@ struct phy_device {
 	u32 advertising;
 	u32 lp_advertising;
 
+	/* Energy efficient ethernet modes which should be prohibited */
+	u32 eee_broken_modes;
+
 	int autoneg;
 
 	int link_timeout;
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH net-next v4 4/4] ARM64: dts: meson: odroidc2: disable advertisement EEE for GbE.

[Jerome Brunet]

Signed-off-by: Jerome Brunet <jbrunet-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Tested-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
---
 arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index e6e3491d48a5..2036582ca0d6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -46,6 +46,7 @@
 
 #include "meson-gxbb.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/mdio.h>
 
 / {
 	compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
@@ -85,6 +86,19 @@
 	status = "okay";
 	pinctrl-0 = <&eth_pins>;
 	pinctrl-names = "default";
+
+	phy-handle = <&eth_phy0>;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			reg = <0>;
+			eee-broken-modes = <MDIO_EEE_1000T>;
+		};
+	};
 };
 
 &ir {
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Florian Fainelli]

On 11/28/2016 07:50 AM, Jerome Brunet wrote:
> This patchset fixes an issue with the OdroidC2 board (DWMAC + RTL8211F).
> The platform seems to enter LPI on the Rx path too often while performing
> relatively high TX transfer. This eventually break the link (both Tx and
> Rx), and require to bring the interface down and up again to get the Rx
> path working again.
> 
> The root cause of this issue is not fully understood yet but disabling EEE
> advertisement on the PHY prevent this feature to be negotiated.
> With this change, the link is stable and reliable, with the expected
> throughput performance.
> 
> The patchset adds options in the generic phy driver to disable EEE
> advertisement, through device tree. The way it is done is very similar
> to the handling of the max-speed property.
> 
> Patch 4 is provided here for testing purpose only. Please don't merge
> patch 4, this change will go through the amlogic's tree.

Sorry, but I really don't like the route this is going, and I should
have made myself clearer before on that, I really think utilizing a PHY
fixup is more appropriate here than an extremely generic DT property.
The fixup code can be in the affected PHY driver, or it can be somewhere
else, your call. There is no shortage of option on how to implement it,
and this would be something easy to enable/disable for known good
configurations (ala PCI/USB fixups).

If we start supporting generic "enable", "disable" type of properties
with values that map directly to register definitions of the HW, we
leave too much room for these properties to be utilized to implement a
specific policy, and this is not acceptable.
-- 
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Jerome Brunet]

On Mon, 2016-11-28 at 09:54 -0800, Florian Fainelli wrote:
> On 11/28/2016 07:50 AM, Jerome Brunet wrote:
> > 
> > This patchset fixes an issue with the OdroidC2 board (DWMAC +
> > RTL8211F).
> > The platform seems to enter LPI on the Rx path too often while
> > performing
> > relatively high TX transfer. This eventually break the link (both
> > Tx and
> > Rx), and require to bring the interface down and up again to get
> > the Rx
> > path working again.
> > 
> > The root cause of this issue is not fully understood yet but
> > disabling EEE
> > advertisement on the PHY prevent this feature to be negotiated.
> > With this change, the link is stable and reliable, with the
> > expected
> > throughput performance.
> > 
> > The patchset adds options in the generic phy driver to disable EEE
> > advertisement, through device tree. The way it is done is very
> > similar
> > to the handling of the max-speed property.
> > 
> > Patch 4 is provided here for testing purpose only. Please don't
> > merge
> > patch 4, this change will go through the amlogic's tree.
> 
> Sorry, but I really don't like the route this is going, and I should
> have made myself clearer before on that, I really think utilizing a
> PHY
> fixup is more appropriate here than an extremely generic DT property.
> The fixup code can be in the affected PHY driver, or it can be
> somewhere
> else, your call. There is no shortage of option on how to implement
> it,
> and this would be something easy to enable/disable for known good
> configurations (ala PCI/USB fixups).
> 
> If we start supporting generic "enable", "disable" type of properties
> with values that map directly to register definitions of the HW, we
> leave too much room for these properties to be utilized to implement
> a
> specific policy, and this is not acceptable.

Florian, 

I agree that DT should not be used to setup a policy, but to describe
what the HW is.

I tried to implement it the way you suggested, using phy fixup, too see
what it looks like.
There is 2 places in the code that seems (remotely) linked to the
issue: 
- meson8b_dwmac driver : if the mac, regardless of the board/platform,
 could not tolerate to have EEE activated, it would make sense to have
the fixup here. It can provide a C callback for such case.
- realtek phy driver: philosophy is kind of the same

To be clear, it is doable and it works that way, but I don't think
embedding this directly in the code is the right way to do it. It seems
we are hiding an information specific about the board inside a generic
driver.

We have several amlogic's design with the same MAC, sometimes with the
same PHY, which have no problem with EEE at all. The issue is really
about the board design.

What I propose is not an enable/disable configuration switch, but to
clearly state that a particular mode of operation is broken. Like the
"max-speed" property, it setup a restriction. IMO, this is a
description of what the HW is and is capable of, and as such it should
be part of the DT.

Yes the property directly map to a register, but it does let you
directly manipulate it (you can't pass the value you want to write in
the register). Having it this way just makes the code simple on both
ends (user and driver).

Yes people could start abusing this to setup policy. In the end, it is
our responsibility, as community, to make sure APIs are used in a
proper way, and not let it be used that way.

I'm open to suggestion on how improve the solution, maybe something
which could bring more confidence that property won't be misused.

Jerome



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Florian Fainelli]

On 11/30/2016 01:47 AM, Jerome Brunet wrote:
>> If we start supporting generic "enable", "disable" type of properties
>> with values that map directly to register definitions of the HW, we
>> leave too much room for these properties to be utilized to implement
>> a
>> specific policy, and this is not acceptable.
> 
> Florian, 
> 
> I agree that DT should not be used to setup a policy, but to describe
> what the HW is.
> 
> I tried to implement it the way you suggested, using phy fixup, too see
> what it looks like.
> There is 2 places in the code that seems (remotely) linked to the
> issue: 
> - meson8b_dwmac driver : if the mac, regardless of the board/platform,
>  could not tolerate to have EEE activated, it would make sense to have
> the fixup here. It can provide a C callback for such case.
> - realtek phy driver: philosophy is kind of the same
> 
> To be clear, it is doable and it works that way, but I don't think
> embedding this directly in the code is the right way to do it. It seems
> we are hiding an information specific about the board inside a generic
> driver.

So there are a few things about that:

- if we were not on ARM64, there would be possibly a remote chance of
having some concept of a board file which would be where such a PHY
fixup, or fixup of any kind would reside

- having the PHY fixup in the PHY driver gated by both an exact match on
the PHY OUI *and* the specific affected board makes it reasonably easy
to locate it

> 
> We have several amlogic's design with the same MAC, sometimes with the
> same PHY, which have no problem with EEE at all. The issue is really
> about the board design.

OK, not a problem then: of_machine_is_compatible() should help you here?

> 
> What I propose is not an enable/disable configuration switch, but to
> clearly state that a particular mode of operation is broken. Like the
> "max-speed" property, it setup a restriction. IMO, this is a
> description of what the HW is and is capable of, and as such it should
> be part of the DT.

Sure, there is a fine line between describing what's broken, and being
able to use that to actually configure non-broken hardware the way you want.

> 
> Yes the property directly map to a register, but it does let you
> directly manipulate it (you can't pass the value you want to write in
> the register). Having it this way just makes the code simple on both
> ends (user and driver).

That's exactly the part that is giving me the creeps, any property that
directly maps to a register value has a chance of a) leading to hard to
debug problem if mis-configured, and b) being used as a policy as
opposed to purely describing what is going on with the HW.

> 
> Yes people could start abusing this to setup policy. In the end, it is
> our responsibility, as community, to make sure APIs are used in a
> proper way, and not let it be used that way.
> 
> I'm open to suggestion on how improve the solution, maybe something
> which could bring more confidence that property won't be misused.

Once the binding lands in the kernel, there is absolutely zero guarantee
nor visibility in how people end-up using in e.g: DT aware bootloader,
and I am one of these people. Since there is a binding, there is
consumer code in the kernel that needs to behave properly with respect
to how the binding is defined. This is the same problem as with any kind
of ABI, and a diverse range of consumers.
-- 
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Russell King - ARM Linux]

On Mon, Nov 28, 2016 at 09:54:28AM -0800, Florian Fainelli wrote:
> If we start supporting generic "enable", "disable" type of properties
> with values that map directly to register definitions of the HW, we
> leave too much room for these properties to be utilized to implement a
> specific policy, and this is not acceptable.

Another concern with this patch is that the existing phylib "set_eee"
code is horribly buggy - it just translates the modes from userspace
into the register value and writes them directly to the register with
no validation.  So it's possible to set modes in the register that the
hardware doesn't support, and have them advertised to the link partner.

I have a patch which fixes that, restricting (as we do elsewhere) the
advert according to the EEE supported capabilities retrieved from the
PCS - maybe the problem here is that the PCS doesn't support support
EEE in 1000baseT mode?

Out of interest, which PHY is used on this platform?

On the SolidRun boards, they're using AR8035, and have suffered this
occasional link drop problem.  What has been found is that it seems to
be to do with the timing parameters, and it seemed to only be 1000bT
that was affected.  I don't remember off hand exactly which or what
the change was they made to stabilise it though, but I can probabily
find out tomorrow.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Yegor Yefremov]

Hi Russel,

On Fri, Jan 6, 2017 at 12:25 AM, Russell King - ARM Linux
<linux@armlinux.org.uk> wrote:
> On Mon, Nov 28, 2016 at 09:54:28AM -0800, Florian Fainelli wrote:
>> If we start supporting generic "enable", "disable" type of properties
>> with values that map directly to register definitions of the HW, we
>> leave too much room for these properties to be utilized to implement a
>> specific policy, and this is not acceptable.
>
> Another concern with this patch is that the existing phylib "set_eee"
> code is horribly buggy - it just translates the modes from userspace
> into the register value and writes them directly to the register with
> no validation.  So it's possible to set modes in the register that the
> hardware doesn't support, and have them advertised to the link partner.
>
> I have a patch which fixes that, restricting (as we do elsewhere) the
> advert according to the EEE supported capabilities retrieved from the
> PCS - maybe the problem here is that the PCS doesn't support support
> EEE in 1000baseT mode?
>
> Out of interest, which PHY is used on this platform?
>
> On the SolidRun boards, they're using AR8035, and have suffered this
> occasional link drop problem.  What has been found is that it seems to
> be to do with the timing parameters, and it seemed to only be 1000bT
> that was affected.  I don't remember off hand exactly which or what
> the change was they made to stabilise it though, but I can probabily
> find out tomorrow.

I have different boards with am335x and AR8035 and we had occasional
link drop with both 100 and 1000 speeds.

Yegor

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Russell King - ARM Linux]

On Fri, Jan 06, 2017 at 06:42:24AM +0100, Yegor Yefremov wrote:
> On Fri, Jan 6, 2017 at 12:25 AM, Russell King - ARM Linux
> <linux-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org> wrote:
> > Another concern with this patch is that the existing phylib "set_eee"
> > code is horribly buggy - it just translates the modes from userspace
> > into the register value and writes them directly to the register with
> > no validation.  So it's possible to set modes in the register that the
> > hardware doesn't support, and have them advertised to the link partner.
> >
> > I have a patch which fixes that, restricting (as we do elsewhere) the
> > advert according to the EEE supported capabilities retrieved from the
> > PCS - maybe the problem here is that the PCS doesn't support support
> > EEE in 1000baseT mode?
> >
> > Out of interest, which PHY is used on this platform?
> >
> > On the SolidRun boards, they're using AR8035, and have suffered this
> > occasional link drop problem.  What has been found is that it seems to
> > be to do with the timing parameters, and it seemed to only be 1000bT
> > that was affected.  I don't remember off hand exactly which or what
> > the change was they made to stabilise it though, but I can probabily
> > find out tomorrow.
> 
> I have different boards with am335x and AR8035 and we had occasional
> link drop with both 100 and 1000 speeds.

AR8035 has "Smart EEE", which is a PHY specific thing... it's not
entirely 802.3 compliant as it doesn't involve the MAC.

The Smart EEE control registers are in the PCS MMD - some of this
is from people's memories:

- 0x805b is the TX wakeup timer.  Lower 8 bits for 100base-Tx and
  upper 8 bits for 1000base-T.

- 0x805c and 0x805d.
  The LPI timer is 24 bit, with the lower 16 bits in 0x805c and the
  upper 8 in 0x805d.  0x805d bit 8 appears to be the Smart EEE enable bit.

What was found was setting the 1000base-T wakeup timer to the same as
the 100base-Tx avoided the problems we were seeing, which was only
with 1000base-T.  (Whether that's because 100base-Tx hasn't been as well
tested, I don't know.)  SR ended up with 0x1717 in 0x805b.

I'd suggest playing around with that register to see if extending the
wakeup time has any beneficial effect.

Also, I suspect Smart EEE shouldn't be enabled if you have an EEE
capable MAC (in which case 0x805d bit 8 should be clear.)  I think,
however, it defaults to enabled.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Jerome Brunet]

On Thu, 2017-01-05 at 23:25 +0000, Russell King - ARM Linux wrote:
> On Mon, Nov 28, 2016 at 09:54:28AM -0800, Florian Fainelli wrote:
> > 
> > If we start supporting generic "enable", "disable" type of
> > properties
> > with values that map directly to register definitions of the HW, we
> > leave too much room for these properties to be utilized to
> > implement a
> > specific policy, and this is not acceptable.
> 
> Another concern with this patch is that the existing phylib "set_eee"
> code is horribly buggy - it just translates the modes from userspace
> into the register value and writes them directly to the register with
> no validation.  So it's possible to set modes in the register that
> the
> hardware doesn't support, and have them advertised to the link
> partner.

Hi Russell,

The purpose of this patch is to provide a way to mark as broken a
particular eee mode. At first, it had nothing to do with "set_eee" but,
as Florian rightly pointed out, users shouldn't be able to re-enable a
broken mode.

At first, I was thinking about returning -ENOSUP if a broken mode was
requested. Then I noticed the behavior you just described: A user can
request anything of "set_eee", he won't necessarily get what he asked
but won't get an error either.

To avoid mixing different topic in a single patch, I kept the same
behavior, not returning an error, just silently discarding broken modes

I agree with you, we should probably validate a bit more what we asked
of the hardware in set_eee.

I wonder if we should return an error though. With the current
implementation, user space application could simply ask to activate
everything, excepting the kernel to sort it out and return an error
only if something horribly wrong happened. If we start returning an
error for unsupported modes, we could break things. I guess we should
just silently filter the requested modes.

> 
> I have a patch which fixes that, restricting (as we do elsewhere) the
> advert according to the EEE supported capabilities retrieved from the
> PCS

Could be interesting :)

>  - maybe the problem here is that the PCS doesn't support support
> EEE in 1000baseT mode?


It does, and that's kind of the problem. EEE in ON for 100Tx and 1000T
by default with this PHY. I have several platform with the same MAC-PHY 
combination. Only the OdroidC2 shows this particular issue with 1000T-
EEE

As explained in other mails in this thread. The problem does not come
from the MAC entering LPI. It actually comes from the link partner
entering LPI on the Rx path under significant Tx transfer. For some
reason, this completely mess up our PHY.

> 
> Out of interest, which PHY is used on this platform?

The PHY is the Realtek RTL8211F

> 
> On the SolidRun boards, they're using AR8035, and have suffered this
> occasional link drop problem.  What has been found is that it seems
> to
> be to do with the timing parameters, and it seemed to only be 1000bT
> that was affected.  I don't remember off hand exactly which or what
> the change was they made to stabilise it though, but I can probabily
> find out tomorrow.
> 

Since the same combination of MAC-PHY works well on other designs, it
is also my feeling that is has something to do with some timing
parameter, maybe related to this particular PCB.

While debugging this issue, we tried to play with all the parameters we
could think of but never found anything worth mentioning.

If you have any ideas, I'd be happy to try.

Jerome

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Russell King - ARM Linux]

On Fri, Jan 06, 2017 at 11:11:36AM +0100, Jerome Brunet wrote:
> The purpose of this patch is to provide a way to mark as broken a
> particular eee mode. At first, it had nothing to do with "set_eee" but,
> as Florian rightly pointed out, users shouldn't be able to re-enable a
> broken mode.

I think something else has been missed - I don't see much point to
telling userspace that (eg) 1000baseT EEE is supported and then
ignore attempts to advertise it.

If it's broken, then arguably the hardware doesn't support the mode,
so we should really be masking those bits from the EEE supported mask
as well.

> I wonder if we should return an error though. With the current
> implementation, user space application could simply ask to activate
> everything, excepting the kernel to sort it out and return an error
> only if something horribly wrong happened. If we start returning an
> error for unsupported modes, we could break things. I guess we should
> just silently filter the requested modes.

The ethtool behaviour for advertisments is that errors are not returned
unless the attempted advert is really wrong.

So, for example, when setting an advertisment for link modes, we accept
the user's supplied mask, and bitwise AND it with the supported mask,
so unsupported link modes are cleared.  Only if the result is an empty
mask do we then return an error to userspace.

It's similar for forcing the link parameters - phylib attempts to find
the best phy setting mode which fuzzily matches the users request, but
doesn't error out if we can't do exactly what the user requested.

In the EEE case, an empty mask is acceptable (it means "EEE is supported
in no link modes") so it isn't appropriate to return errors there.

> >  - maybe the problem here is that the PCS doesn't support support
> > EEE in 1000baseT mode?
> 
> 
> It does, and that's kind of the problem. EEE in ON for 100Tx and 1000T
> by default with this PHY. I have several platform with the same MAC-PHY 
> combination. Only the OdroidC2 shows this particular issue with 1000T-
> EEE
> 
> As explained in other mails in this thread. The problem does not come
> from the MAC entering LPI. It actually comes from the link partner
> entering LPI on the Rx path under significant Tx transfer. For some
> reason, this completely mess up our PHY.

For a 1000baseT link to enter low power, both ends have to enter LPI
(see 802.3 78.1.3.3.1) - the Tx and Rx paths can't independently enter
LPI.

So, if you have a busy Tx link, the link itself can't be entering LPI.
Your link partner may be sending a request to enter LPI due to its own
Tx path being idle, which should then be forwarded to your MAC.

It's pretty hard to see what could be messed up with that - I'd have
expected the problems to occur when both ends were idle and the link
had entered low power mode.

> > On the SolidRun boards, they're using AR8035, and have suffered this
> > occasional link drop problem.  What has been found is that it seems
> > to
> > be to do with the timing parameters, and it seemed to only be 1000bT
> > that was affected.  I don't remember off hand exactly which or what
> > the change was they made to stabilise it though, but I can probabily
> > find out tomorrow.
> > 
> 
> Since the same combination of MAC-PHY works well on other designs, it
> is also my feeling that is has something to do with some timing
> parameter, maybe related to this particular PCB.

Maybe a different PHY interface?  Meson seems to use RGMII, maybe
others use SGMII - but then I'd expect 100base-Tx to also be broken.
So not really sure.

I was talking to Florian about that last night, because the mis-named
phy_init_eee() tests for various phy interface modes before proceeding,
which seems to be fairly rubbish as the list of interface modes is
gradually increasing since it was introduced (and I need to add SGMII
to it.)  The conclusion I've come to there is that the test should
never have been part of phylib, because if there are restrictions on
which phy interface modes are allowable for EEE, they're likely to be
either PHY or MAC specific.

The other problem that having the test there causes is that if the
existing users can't handle EEE over SGMII, then when I add SGMII to
support my hardware, they end up breaking - far from desirable.
There's no information on why the test is there, or even which PHYs
or MACs it's applicable to, which makes this unnecessarily more
difficult to now resolve.

My feeling is that the integration of EEE into phylib is fairly poor
at the moment, and we need to be a lot smarter about it.

BTW, one of the problems (not caused by your patch) is that changing
the EEE advertisment does not (on all PHY drivers) cause the link to
be renegotiated - there's no call to phy_start_aneg() when the advert
changes, and even if there was, there's no guarantee that
phy_start_aneg() will even set the AN restart bit in the control
register.

However, given that you're hooking into the set_eee function, I'm not
sure why you placed your EEE advertisment thing into config_aneg() -
isn't it more an initialisation thing (so should be in config_init()?)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Jerome Brunet]

On Fri, 2017-01-06 at 11:42 +0000, Russell King - ARM Linux wrote:
> On Fri, Jan 06, 2017 at 11:11:36AM +0100, Jerome Brunet wrote:
> > 
> > The purpose of this patch is to provide a way to mark as broken a
> > particular eee mode. At first, it had nothing to do with "set_eee"
> > but,
> > as Florian rightly pointed out, users shouldn't be able to re-
> > enable a
> > broken mode.
> 
> I think something else has been missed - I don't see much point to
> telling userspace that (eg) 1000baseT EEE is supported and then
> ignore attempts to advertise it.
> 
> If it's broken, then arguably the hardware doesn't support the mode,
> so we should really be masking those bits from the EEE supported mask
> as well.

indeed.

> 
> > 
[...]
> 
> > 
> > > 
> > >  - maybe the problem here is that the PCS doesn't support support
> > > EEE in 1000baseT mode?
> > 
> > 
> > It does, and that's kind of the problem. EEE in ON for 100Tx and
> > 1000T
> > by default with this PHY. I have several platform with the same
> > MAC-PHY 
> > combination. Only the OdroidC2 shows this particular issue with
> > 1000T-
> > EEE
> > 
> > As explained in other mails in this thread. The problem does not
> > come
> > from the MAC entering LPI. It actually comes from the link partner
> > entering LPI on the Rx path under significant Tx transfer. For some
> > reason, this completely mess up our PHY.
> 
> For a 1000baseT link to enter low power, both ends have to enter LPI
> (see 802.3 78.1.3.3.1) - the Tx and Rx paths can't independently
> enter
> LPI.
> 
> So, if you have a busy Tx link, the link itself can't be entering
> LPI.
> Your link partner may be sending a request to enter LPI due to its
> own
> Tx path being idle, which should then be forwarded to your MAC.
> 
> It's pretty hard to see what could be messed up with that - I'd have
> expected the problems to occur when both ends were idle and the link
> had entered low power mode.

Well, maybe I'm not explaining the issue very well. Here the test done
which led me to this conclusion:

The test are done using iperf. Receiving data works well, with the
expected performance. Sending data is the problem, and only under high
load:

Here are the lpi stats before starting the test:
     irq_tx_path_in_lpi_mode_n: 6
     irq_tx_path_exit_lpi_mode_n: 5
     irq_rx_path_in_lpi_mode_n: 76
     irq_rx_path_exit_lpi_mode_n: 75
     phy_eee_wakeup_error_n: 0

Sending data with iperf usually works for little while (between 0 and
10s)

# iperf3 -c 192.168.1.170 -p12345
Connecting to host 192.168.1.170, port 12345
local 192.168.1.30 port 54450 connected to 192.168.1.170 port 12345
Interval           Transfer     Bandwidth       Retr  Cwnd
0.00-1.00   sec   112 MBytes   938 Mbits/sec    0    409 KBytes       
1.00-2.00   sec   112 MBytes   940 Mbits/sec    0    426 KBytes       
2.00-3.00   sec   112 MBytes   939 Mbits/sec    0    426 KBytes       
3.00-4.00   sec   112 MBytes   940 Mbits/sec    0    426 KBytes       
4.00-5.00   sec   112 MBytes   940 Mbits/sec    0    426 KBytes       
5.00-6.00   sec   112 MBytes   939 Mbits/sec    0    426 KBytes       
6.00-7.00   sec  9.26 MBytes  77.6 Mbits/sec    2   1.41 KBytes <=Issue
   
7.00-8.00   sec  0.00 Bytes  0.00 bits/sec    1   1.41 KBytes       
8.00-9.00   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes       
^C10.00-13.58  sec  0.00 Bytes  0.00 bits/sec    1   1.41 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
Interval           Transfer     Bandwidth       Retr
0.00-13.58  sec   681 MBytes   421 Mbits/sec    4             sender
0.00-13.58  sec  0.00 Bytes  0.00 bits/sec                  receiver
iperf3: interrupt - the client has terminated

iperf3 does not exit ant the link seems completely broken. We cannot
send or receive until the interface is brought down then up again.

Here are the LPI related stats after the test:
     irq_tx_path_in_lpi_mode_n: 48
     irq_tx_path_exit_lpi_mode_n: 48
     irq_rx_path_in_lpi_mode_n: 325
     irq_rx_path_exit_lpi_mode_n: 325
     phy_eee_wakeup_error_n: 0


This happens with :
1) Default configuration: EEE enabled on the MAC, PHY with reset
settings (EEE advertised)
2) EEE disabled on the MAC, PHY still with reset settings (EEE
advertised). In such case there is no irq_tx_path_*_lpi_mode interrupts
at all but still a lot of irq_rx_path_*_lpi_mode interrupts. So even if
the mac does not drive anything EEE related, there is still something
happening between the PHY and the link partner regarding EEE.

3) Disabling EEE advertisement for 1000t: no irq_*_lpi_mode at all. The
feature is not negotiated and the Tx works well.

By the way, EEE work well for the 100tx on the same HW.

> 
> > 
> > > 
> > > On the SolidRun boards, they're using AR8035, and have suffered
> > > this
> > > occasional link drop problem.  What has been found is that it
> > > seems
> > > to
> > > be to do with the timing parameters, and it seemed to only be
> > > 1000bT
> > > that was affected.  I don't remember off hand exactly which or
> > > what
> > > the change was they made to stabilise it though, but I can
> > > probabily
> > > find out tomorrow.
> > > 
> > 
> > Since the same combination of MAC-PHY works well on other designs,
> > it
> > is also my feeling that is has something to do with some timing
> > parameter, maybe related to this particular PCB.
> 
> Maybe a different PHY interface?  Meson seems to use RGMII, maybe
> others use SGMII - but then I'd expect 100base-Tx to also be broken.
> So not really sure.

Nope, same interface (RGMII), same SoC. Only the PCB layout and
external components might be different.

> 
> I was talking to Florian about that last night, because the mis-named
> phy_init_eee() tests for various phy interface modes before
> proceeding,
> which seems to be fairly rubbish as the list of interface modes is
> gradually increasing since it was introduced (and I need to add SGMII
> to it.)  The conclusion I've come to there is that the test should
> never have been part of phylib, because if there are restrictions on
> which phy interface modes are allowable for EEE, they're likely to be
> either PHY or MAC specific.
> 
> The other problem that having the test there causes is that if the
> existing users can't handle EEE over SGMII, then when I add SGMII to
> support my hardware, they end up breaking - far from desirable.
> There's no information on why the test is there, or even which PHYs
> or MACs it's applicable to, which makes this unnecessarily more
> difficult to now resolve.
> 
> My feeling is that the integration of EEE into phylib is fairly poor
> at the moment, and we need to be a lot smarter about it.

You know a lot more than I do on this topic obviously. I'm just trying
to make GbE work (as cleanly as possible) on that board to be honest.

So I'm not sure I understand, are you against EEE integration in phylib
entirely, or specifically against the test I added in set_eee to filter
out broken modes ?

Since set_eee directly set the register, I don't see where else I could
have put this test to prevent EEE broken modes from being re-enabled.

> 
> BTW, one of the problems (not caused by your patch) is that changing
> the EEE advertisment does not (on all PHY drivers) cause the link to
> be renegotiated - there's no call to phy_start_aneg() when the advert
> changes, and even if there was, there's no guarantee that
> phy_start_aneg() will even set the AN restart bit in the control
> register.
> 
> However, given that you're hooking into the set_eee function, I'm not
> sure why you placed your EEE advertisment thing into config_aneg() -
> isn't it more an initialisation thing (so should be in
> config_init()?)

What I change is what the PHY advertise, so it seems logical to do it
where "genphy_config_advert" was called. Just taking the existing code
as an example

> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next v4 0/4] Fix OdroidC2 Gigabit Tx link issue

[Russell King - ARM Linux]

(quick reply...)

On Fri, Jan 06, 2017 at 02:50:21PM +0100, Jerome Brunet wrote:
> So I'm not sure I understand, are you against EEE integration in phylib
> entirely, or specifically against the test I added in set_eee to filter
> out broken modes ?

I'm happy to see EEE integrated into phylib, but I think the current
implementation is very buggy and needs a rewrite.

> > BTW, one of the problems (not caused by your patch) is that changing
> > the EEE advertisment does not (on all PHY drivers) cause the link to
> > be renegotiated - there's no call to phy_start_aneg() when the advert
> > changes, and even if there was, there's no guarantee that
> > phy_start_aneg() will even set the AN restart bit in the control
> > register.
> > 
> > However, given that you're hooking into the set_eee function, I'm not
> > sure why you placed your EEE advertisment thing into config_aneg() -
> > isn't it more an initialisation thing (so should be in
> > config_init()?)
> 
> What I change is what the PHY advertise, so it seems logical to do it
> where "genphy_config_advert" was called. Just taking the existing code
> as an example

You need to adjust the adverisment in two places:

1. On initialisation, when you need to change the default value.
2. Whenever the user requests a different EEE advertisment.

You don't need to do it each time config_aneg() is called - nothing's
going to change the EEE advertisment in that path.  Hence, to check
it each and every time seems like a waste of CPU cycles.

However, there's another path that needs to be considered, which the
current EEE code fails to do, and that is the resume path.  Nothing
at present saves and restores the EEE settings, they are completely
lost if the PHY is powered down.  This is just another symptom of the
current poor quality EEE implementation in phylib, and another reason
why I say above that the EEE code is in need of a rewrite... which is
something I will be looking at.

If the EEE settings are properly saved and restored over suspend/
resume, then the previously programmed EEE advertisment would also
be restored.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH net-next v4 2/4] dt-bindings: net: add EEE capability constants

[Jerome Brunet]

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
---
 include/dt-bindings/net/mdio.h | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
 create mode 100644 include/dt-bindings/net/mdio.h

diff --git a/include/dt-bindings/net/mdio.h b/include/dt-bindings/net/mdio.h
new file mode 100644
index 000000000000..99c6d903d439
--- /dev/null
+++ b/include/dt-bindings/net/mdio.h
@@ -0,0 +1,19 @@
+/*
+ * This header provides generic constants for ethernet MDIO bindings
+ */
+
+#ifndef _DT_BINDINGS_NET_MDIO_H
+#define _DT_BINDINGS_NET_MDIO_H
+
+/*
+ * EEE capability Advertisement
+ */
+
+#define MDIO_EEE_100TX		0x0002	/* 100TX EEE cap */
+#define MDIO_EEE_1000T		0x0004	/* 1000T EEE cap */
+#define MDIO_EEE_10GT		0x0008	/* 10GT EEE cap */
+#define MDIO_EEE_1000KX		0x0010	/* 1000KX EEE cap */
+#define MDIO_EEE_10GKX4		0x0020	/* 10G KX4 EEE cap */
+#define MDIO_EEE_10GKR		0x0040	/* 10G KR EEE cap */
+
+#endif
-- 
2.7.4

Re: [PATCH net-next v4 2/4] dt-bindings: net: add EEE capability constants

[Rob Herring]

On Mon, Nov 28, 2016 at 04:50:26PM +0100, Jerome Brunet wrote:
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
> Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
> Tested-by: Andreas Färber <afaerber@suse.de>
> Tested-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  include/dt-bindings/net/mdio.h | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
>  create mode 100644 include/dt-bindings/net/mdio.h

Seems changes are wanted on this, but patches 2 and 3 should be 
combined. The header is part of the binding doc.

Rob

Re: [PATCH net-next v4 2/4] dt-bindings: net: add EEE capability constants

[Jerome Brunet]

Hi Rob,

First, Thx for this information and sorry for this late reply
As you may have seen yourself, there was little bit of confusion while
discussing this patch series.

The point is the v3 was applied before your reply (patches 2 and 3 not
combined unfortunately).
Because of this confusion, the series needed a few fixes witch removes
the previously added bindings [0].
This time, I made sure to modify (remove) the bindings along with the
documentation.

[0]: http://lkml.kernel.org/r/1482159938-13239-1-git-send-email-jbrunet
@baylibre.com

Cheers
Jerome

On Mon, 2016-12-05 at 08:39 -0600, Rob Herring wrote:
> On Mon, Nov 28, 2016 at 04:50:26PM +0100, Jerome Brunet wrote:
> > 
> > Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
> > Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
> > Tested-by: Andreas Färber <afaerber@suse.de>
> > Tested-by: Neil Armstrong <narmstrong@baylibre.com>
> > ---
> >  include/dt-bindings/net/mdio.h | 19 +++++++++++++++++++
> >  1 file changed, 19 insertions(+)
> >  create mode 100644 include/dt-bindings/net/mdio.h
> 
> Seems changes are wanted on this, but patches 2 and 3 should be 
> combined. The header is part of the binding doc.
> 
> Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v4 3/4] dt: bindings: add ethernet phy eee-broken-modes option documentation

[Jerome Brunet]

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
---
 Documentation/devicetree/bindings/net/phy.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index 4627da3d52c4..54749b60a466 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -38,6 +38,8 @@ Optional Properties:
 - enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to
   compensate for the board being designed with the lanes swapped.
 
+- eee-broken-modes: Bits to clear in the MDIO_AN_EEE_ADV register to
+  disable EEE broken modes.
 
 Example:
 
-- 
2.7.4