* [PATCH v3 2/2] ARM: dts: imx6q: Add mccmon6 board support
2017-01-03 10:46 [PATCH v3 1/2] Doc: devicetree: bindings: Add vendor prefix entry - lwn Lukasz Majewski
@ 2017-01-03 10:46 ` Lukasz Majewski
[not found] ` <1483440381-24268-2-git-send-email-lukma-ynQEQJNshbs@public.gmane.org>
2017-01-04 14:16 ` [PATCH v3 1/2] Doc: devicetree: bindings: Add vendor prefix entry - lwn Rob Herring
[not found] ` <1483440381-24268-1-git-send-email-lukma-ynQEQJNshbs@public.gmane.org>
2 siblings, 1 reply; 5+ messages in thread
From: Lukasz Majewski @ 2017-01-03 10:46 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Russell King, Shawn Guo, Fabio Estevam,
linux-kernel, devicetree, linux-arm-kernel, Vladimir Zapolskiy
Cc: Sascha Hauer, Zerlauth Karl (LWN), Lukasz Majewski,
Lukasz Majewski
From: Lukasz Majewski <l.majewski@majess.pl>
This patch provides support for Liebherr's Monitor 6 board (abverrated as
mccmon6) to Linux kernel.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
---
Changes for v3:
- Reorganize the dts file according to Shawn Guo's comments
Changes for v2:
- Reorganize the dts file according to Valdimir Zapolskiy's comments
---
MCCMON6 board support depends on following patches:
1. "video: backlight: pwm_bl: Initialize fb_bl_on[x] and use_count during pwm_backlight_probe()"
http://patchwork.ozlabs.org/patch/708844/
2. "pwm: imx: Provide atomic operation for IMX PWM driver"
http://patchwork.ozlabs.org/patch/708847/ - http://patchwork.ozlabs.org/patch/708843/
The patch applies to v4.10-rc2
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-mccmon6.dts | 473 ++++++++++++++++++++++++++++++++++++
2 files changed, 474 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-mccmon6.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb..316c178 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -393,6 +393,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-icore.dtb \
imx6q-icore-rqs.dtb \
imx6q-marsboard.dtb \
+ imx6q-mccmon6.dtb \
imx6q-nitrogen6x.dtb \
imx6q-nitrogen6_max.dtb \
imx6q-nitrogen6_som2.dtb \
diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts b/arch/arm/boot/dts/imx6q-mccmon6.dts
new file mode 100644
index 0000000..eedbe73
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-mccmon6.dts
@@ -0,0 +1,473 @@
+/*
+ * Copyright 2016-2017
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Liebherr (LWN) monitor6 i.MX6 Quad Board";
+ compatible = "lwn,mccmon6", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100 101 102 103 104 105 106 107 108 109
+ 110 111 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127 128 129
+ 130 131 132 133 134 135 136 137 138 139
+ 140 141 142 143 144 145 146 147 148 149
+ 150 151 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167 168 169
+ 170 171 172 173 174 175 176 177 178 179
+ 180 181 182 183 184 185 186 187 188 189
+ 190 191 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207 208 209
+ 210 211 212 213 214 215 216 217 218 219
+ 220 221 222 223 224 225 226 227 228 229
+ 230 231 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247 248 249
+ 250 251 252 253 254 255>;
+ default-brightness-level = <50>;
+ enable-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ };
+
+ reg_lvds: regulator-lvds {
+ compatible = "regulator-fixed";
+ regulator-name = "lvds_ppen";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_lvds>;
+ gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ panel-lvds0 {
+ compatible = "innolux,g121x1-l03";
+ backlight = <&backlight_lvds>;
+ power-supply = <®_lvds>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
+ status = "okay";
+
+ s25sl032p: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pfuze100: pmic@08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pwm2 {
+ #pwm-cells = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&weim {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ status = "okay";
+
+ nor@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x02000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ bank-width = <2>;
+ use-advanced-sector-protection;
+ fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+ 0x0000c000 0x1404a38e 0x00000000>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_backlight: dispgrp {
+ fsl,pins = <
+ /* BLEN_OUT */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi3_cs: ecspi3csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000
+ >;
+ };
+
+ pinctrl_ecspi3_flwp: ecspi3flwpgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x80000000
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_lvds: reqlvdsgrp {
+ fsl,pins = <
+ /* LVDS_PPEN_OUT */
+ MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x17059
+ >;
+ };
+
+ pinctrl_weim_cs0: weimcs0grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
+ >;
+ };
+
+ pinctrl_weim_nor: weimnorgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
+ MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
+ MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+ MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+ MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+ MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+ MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+ MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+ MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+ MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+ MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+ MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+ MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+ MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+ MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+ MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+ MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+ MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+ MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+ MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+ MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+ MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+ MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+ MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+ MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+ MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+ MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+ MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
+ MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
+ MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
+ MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
+ MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
+ MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
+ MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
+ MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
+ MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
+ MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
+ MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
+ MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
+ MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
+ MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
+ MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
+ MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
+ >;
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 5+ messages in thread* Re: [PATCH v3 1/2] Doc: devicetree: bindings: Add vendor prefix entry - lwn
2017-01-03 10:46 [PATCH v3 1/2] Doc: devicetree: bindings: Add vendor prefix entry - lwn Lukasz Majewski
2017-01-03 10:46 ` [PATCH v3 2/2] ARM: dts: imx6q: Add mccmon6 board support Lukasz Majewski
@ 2017-01-04 14:16 ` Rob Herring
[not found] ` <1483440381-24268-1-git-send-email-lukma-ynQEQJNshbs@public.gmane.org>
2 siblings, 0 replies; 5+ messages in thread
From: Rob Herring @ 2017-01-04 14:16 UTC (permalink / raw)
To: Lukasz Majewski
Cc: Mark Rutland, Russell King, Shawn Guo, Fabio Estevam,
linux-kernel, devicetree, linux-arm-kernel, Vladimir Zapolskiy,
Sascha Hauer, Zerlauth Karl (LWN), Lukasz Majewski
On Tue, Jan 03, 2017 at 11:46:20AM +0100, Lukasz Majewski wrote:
> This patch adds entry for LWN - the Liebherr-Werk Nenzing GmbH company to
> vendor-prefixes.txt file.
>
> Signed-off-by: Lukasz Majewski <lukma@denx.de>
> ---
> Changes for v3:
> - Update to v4.10-rc2
>
> Changes for v2:
> - New patch
> ---
> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
> 1 file changed, 1 insertion(+)
I guess LWN.net will never make any devices...
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 5+ messages in thread