Re: [RESEND PATCH 6/6] dt-bindings: phy-mt65xx-usb: add support for mt2712 platform

[Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>]

On Wed, Jan 18, 2017 at 02:00:14PM +0800, Chunfeng Yun wrote:
> add a new compatible string for "mt2712", and a new reference clock
> for SuperSpeed analog phy;
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> ---
>  .../devicetree/bindings/phy/phy-mt65xx-usb.txt     |   81 +++++++++++++++++---
>  1 file changed, 70 insertions(+), 11 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> index 33a2b1e..8f91136 100644
> --- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> @@ -6,19 +6,25 @@ This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
>  Required properties (controller (parent) node):
>   - compatible	: should be one of
>  		  "mediatek,mt2701-u3phy"
> +		  "mediatek,mt2712-u3phy"
>  		  "mediatek,mt8173-u3phy"
> - - reg		: offset and length of register for phy, exclude port's
> -		  register.
>   - clocks	: a list of phandle + clock-specifier pairs, one for each
>  		  entry in clock-names
>   - clock-names	: must contain
> -		  "u3phya_ref": for reference clock of usb3.0 analog phy.
> +		  "u2ref_clk": 48M reference clock of HighSpeed analog phy.
> +		  "u3ref_clk": 26M reference clock of SuperSpeed analog phy,
> +			sometimes is 24M, 25M or 27M, depended on platform.

_clk is redundant.

>  
>  Required nodes	: a sub-node is required for each port the controller
>  		  provides. Address range information including the usual
>  		  'reg' property is used inside these nodes to describe
>  		  the controller's topology.
>  
> +Optional properties (controller (parent) node):
> + - reg		: offset and length of register shared by multiple ports,
> +		  exclude port's private register. It is needed on mt2701
> +		  and mt8173, but not on mt2712.
> +
>  Required properties (port (child) node):
>  - reg		: address and length of the register set for the port.
>  - #phy-cells	: should be 1 (See second example)
> @@ -31,21 +37,27 @@ Example:
>  u3phy: usb-phy@11290000 {
>  	compatible = "mediatek,mt8173-u3phy";
>  	reg = <0 0x11290000 0 0x800>;
> -	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
> -	clock-names = "u3phya_ref";
> +	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>, <&clk26m>;
> +	clock-names = "u2ref_clk", "u3ref_clk";
>  	#address-cells = <2>;
>  	#size-cells = <2>;
>  	ranges;
>  	status = "okay";
>  
> -	phy_port0: port@11290800 {
> -		reg = <0 0x11290800 0 0x800>;
> +	u2port0: port@11290800 {

port is for OF graph. This should be usb-phy@... instead.

> +		reg = <0 0x11290800 0 0x100>;
> +		#phy-cells = <1>;
> +		status = "okay";
> +	};
> +
> +	u3port0: port@11290900 {
> +		reg = <0 0x11290800 0 0x700>;
>  		#phy-cells = <1>;
>  		status = "okay";
>  	};
>  
> -	phy_port1: port@11291000 {
> -		reg = <0 0x11291000 0 0x800>;
> +	u2port1: port@11291000 {
> +		reg = <0 0x11291000 0 0x100>;
>  		#phy-cells = <1>;
>  		status = "okay";
>  	};
> @@ -64,7 +76,54 @@ Example:
>  
>  usb30: usb@11270000 {
>  	...
> -	phys = <&phy_port0 PHY_TYPE_USB3>;
> -	phy-names = "usb3-0";
> +	phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
> +	phy-names = "usb2-0", "usb3-0";
>  	...
>  };
> +
> +
> +Layout differences of banks between mt8173/mt2701 and mt2712
> +-------------------------------------------------------------
> +mt8173 and mt2701:
> +port        offset    bank
> +shared      0x0000    SPLLC
> +            0x0100    FMREG
> +u2 port0    0x0800    U2PHY_COM
> +u3 port0    0x0900    U3PHYD
> +            0x0a00    U3PHYD_BANK2
> +            0x0b00    U3PHYA
> +            0x0c00    U3PHYA_DA
> +u2 port1    0x1000    U2PHY_COM
> +u3 port1    0x1100    U3PHYD
> +            0x1200    U3PHYD_BANK2
> +            0x1300    U3PHYA
> +            0x1400    U3PHYA_DA
> +u2 port2    0x1800    U2PHY_COM
> +            ...
> +
> +mt2712:
> +port        offset    bank
> +u2 port0    0x0000    MISC
> +            0x0100    FMREG
> +            0x0300    U2PHY_COM
> +u3 port0    0x0700    SPLLC
> +            0x0800    CHIP
> +            0x0900    U3PHYD
> +            0x0a00    U3PHYD_BANK2
> +            0x0b00    U3PHYA
> +            0x0c00    U3PHYA_DA
> +u2 port1    0x1000    MISC
> +            0x1100    FMREG
> +            0x1300    U2PHY_COM
> +u3 port1    0x1700    SPLLC
> +            0x1800    CHIP
> +            0x1900    U3PHYD
> +            0x1a00    U3PHYD_BANK2
> +            0x1b00    U3PHYA
> +            0x1c00    U3PHYA_DA
> +u2 port2    0x2000    MISC
> +            ...
> +
> +    SPLLC shared by u3 ports and FMREG shared by u2 ports on
> +mt8173/mt2701 are put back into each port; a new bank MISC for
> +u2 ports and CHIP for u3 ports are added on mt2712.
> -- 
> 1.7.9.5
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html