Re: [PATCH 1/5] drm: zte: add interlace mode support

[Sean Paul <seanpaul-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>]

On Fri, Jan 20, 2017 at 12:24:56AM +0800, Shawn Guo wrote:
> From: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> 
> It adds interlace mode support in VOU TIMING_CTRL and channel control
> block, so that VOU driver gets ready to support output device in
> interlace mode like TV Encoder.
> 
> Signed-off-by: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> ---
>  drivers/gpu/drm/zte/zx_vou.c      | 53 +++++++++++++++++++++++++++++++++++++--
>  drivers/gpu/drm/zte/zx_vou_regs.h | 15 +++++++++++
>  2 files changed, 66 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/zte/zx_vou.c b/drivers/gpu/drm/zte/zx_vou.c
> index 3056b41df518..8c4f0e2885f3 100644
> --- a/drivers/gpu/drm/zte/zx_vou.c
> +++ b/drivers/gpu/drm/zte/zx_vou.c

<snip>

> @@ -196,19 +211,26 @@ static inline void vou_chn_set_update(struct zx_crtc *zcrtc)
>  static void zx_crtc_enable(struct drm_crtc *crtc)
>  {
>  	struct drm_display_mode *mode = &crtc->state->adjusted_mode;
> +	bool interlaced = mode->flags & DRM_MODE_FLAG_INTERLACE;
>  	struct zx_crtc *zcrtc = to_zx_crtc(crtc);
>  	struct zx_vou_hw *vou = zcrtc->vou;
>  	const struct zx_crtc_regs *regs = zcrtc->regs;
>  	const struct zx_crtc_bits *bits = zcrtc->bits;
>  	struct videomode vm;
> +	u32 vactive;
>  	u32 pol = 0;
>  	u32 val;
> +	u32 mask;
>  	int ret;
>  
>  	drm_display_mode_to_videomode(mode, &vm);
>  
>  	/* Set up timing parameters */
> -	val = V_ACTIVE(vm.vactive - 1);
> +	vactive = vm.vactive;
> +	if (interlaced)
> +		vactive /= 2;
> +
> +	val = V_ACTIVE(vactive - 1);

Instead of introducing a new var, I think you can get away with:

if (interlaced)
        val = V_ACTIVE(vm.vactive / 2);
else
        val = V_ACTIVE(vm.vactive - 1);


>  	val |= H_ACTIVE(vm.hactive - 1);
>  	zx_writel(vou->timing + regs->fir_active, val);
>  
> @@ -222,6 +244,22 @@ static void zx_crtc_enable(struct drm_crtc *crtc)
>  	val |= FRONT_PORCH(vm.vfront_porch - 1);
>  	zx_writel(vou->timing + regs->fir_vtiming, val);
>  
> +	if (interlaced) {
> +		u32 shift = bits->sec_vactive_shift;
> +		u32 mask = bits->sec_vactive_mask;

mask is already defined at the function scope

> +
> +		val = zx_readl(vou->timing + SEC_V_ACTIVE);
> +		val &= ~mask;
> +		val |= ((vactive - 1) << shift) & mask;
> +		zx_writel(vou->timing + SEC_V_ACTIVE, val);
> +
> +		val = SYNC_WIDE(vm.vsync_len - 1);
> +		/* sec_vbp = fir_vbp + 1 */

Looks like leftover kruft here.

> +		val |= BACK_PORCH(vm.vback_porch);
> +		val |= FRONT_PORCH(vm.vfront_porch - 1);
> +		zx_writel(vou->timing + regs->sec_vtiming, val);
> +	}
> +
>  	/* Set up polarities */
>  	if (vm.flags & DISPLAY_FLAGS_VSYNC_LOW)
>  		pol |= 1 << POL_VSYNC_SHIFT;
> @@ -232,9 +270,16 @@ static void zx_crtc_enable(struct drm_crtc *crtc)
>  		       pol << bits->polarity_shift);
>  
>  	/* Setup SHIFT register by following what ZTE BSP does */
> -	zx_writel(vou->timing + regs->timing_shift, H_SHIFT_VAL);
> +	val = H_SHIFT_VAL;
> +	if (interlaced)
> +		val |= V_SHIFT_VAL << 16;
> +	zx_writel(vou->timing + regs->timing_shift, val);
>  	zx_writel(vou->timing + regs->timing_pi_shift, H_PI_SHIFT_VAL);
>  
> +	/* Progressive or interlace scan select */
> +	mask = bits->interlace_select | bits->pi_enable;
> +	zx_writel_mask(vou->timing + SCAN_CTRL, mask, interlaced ? mask : 0);
> +
>  	/* Enable TIMING_CTRL */
>  	zx_writel_mask(vou->timing + TIMING_TC_ENABLE, bits->tc_enable,
>  		       bits->tc_enable);
> @@ -245,6 +290,10 @@ static void zx_crtc_enable(struct drm_crtc *crtc)
>  	zx_writel_mask(zcrtc->chnreg + CHN_CTRL1, CHN_SCREEN_H_MASK,
>  		       vm.vactive << CHN_SCREEN_H_SHIFT);
>  
> +	/* Configure channel interlace buffer control */
> +	zx_writel_mask(zcrtc->chnreg + CHN_INTERLACE_BUF_CTRL, CHN_INTERLACE_EN,
> +		       interlaced ? CHN_INTERLACE_EN : 0);
> +
>  	/* Update channel */
>  	vou_chn_set_update(zcrtc);
>  
> diff --git a/drivers/gpu/drm/zte/zx_vou_regs.h b/drivers/gpu/drm/zte/zx_vou_regs.h
> index 193c1ce01fe7..e6ed844e068a 100644
> --- a/drivers/gpu/drm/zte/zx_vou_regs.h
> +++ b/drivers/gpu/drm/zte/zx_vou_regs.h
> @@ -75,6 +75,8 @@
>  #define CHN_SCREEN_H_SHIFT		5
>  #define CHN_SCREEN_H_MASK		(0x1fff << CHN_SCREEN_H_SHIFT)
>  #define CHN_UPDATE			0x08
> +#define CHN_INTERLACE_BUF_CTRL		0x24

Maybe it's my email reader, but it seems like there's an alignment issue here.

> +#define CHN_INTERLACE_EN		BIT(2)
>  
>  /* TIMING_CTRL registers */
>  #define TIMING_TC_ENABLE		0x04
> @@ -117,6 +119,19 @@
>  #define TIMING_MAIN_SHIFT		0x2c
>  #define TIMING_AUX_SHIFT		0x30
>  #define H_SHIFT_VAL			0x0048
> +#define V_SHIFT_VAL			0x0001
> +#define SCAN_CTRL			0x34
> +#define AUX_PI_EN			BIT(19)
> +#define MAIN_PI_EN			BIT(18)
> +#define AUX_INTERLACE_SEL		BIT(1)
> +#define MAIN_INTERLACE_SEL		BIT(0)
> +#define SEC_V_ACTIVE			0x38
> +#define SEC_VACT_MAIN_SHIFT		0
> +#define SEC_VACT_MAIN_MASK		(0xffff << SEC_VACT_MAIN_SHIFT)
> +#define SEC_VACT_AUX_SHIFT		16
> +#define SEC_VACT_AUX_MASK		(0xffff << SEC_VACT_AUX_SHIFT)
> +#define SEC_MAIN_V_TIMING		0x3c
> +#define SEC_AUX_V_TIMING		0x40
>  #define TIMING_MAIN_PI_SHIFT		0x68
>  #define TIMING_AUX_PI_SHIFT		0x6c
>  #define H_PI_SHIFT_VAL			0x000f
> -- 
> 1.9.1
> 
> _______________________________________________
> dri-devel mailing list
> dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW@public.gmane.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html