From: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
To: gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org,
jslaby-IBi9RG/b67k@public.gmane.org,
linux-serial-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
kernel-F5mvAk5X5gdBDgjK7y7TUQ@public.gmane.org,
patrice.chotard-qxv4g6HH51o@public.gmane.org,
Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Subject: [PATCH v4 09/10] ARM: dts: STiH407-family: Use new Pinctrl groups
Date: Fri, 3 Feb 2017 10:23:18 +0000 [thread overview]
Message-ID: <20170203102319.23489-10-lee.jones@linaro.org> (raw)
In-Reply-To: <20170203102319.23489-1-lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Having just defined some new Pinctrl groups for when HW flow-control
is {en,dis}abled, let's reference them for use within the driver.
Acked-by: Peter Griffin <peter.griffin-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/stih407-family.dtsi | 3 +--
arch/arm/boot/dts/stih410-b2260.dts | 5 ++++-
2 files changed, 5 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi
index c8b2944..e480e32 100644
--- a/arch/arm/boot/dts/stih407-family.dtsi
+++ b/arch/arm/boot/dts/stih407-family.dtsi
@@ -222,9 +222,8 @@
compatible = "st,asc";
reg = <0x9830000 0x2c>;
interrupts = <GIC_SPI 122 IRQ_TYPE_NONE>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_serial0>;
clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+ /* Pinctrl moved out to a per-board configuration */
status = "disabled";
};
diff --git a/arch/arm/boot/dts/stih410-b2260.dts b/arch/arm/boot/dts/stih410-b2260.dts
index fa16aba..cbcbcb4 100644
--- a/arch/arm/boot/dts/stih410-b2260.dts
+++ b/arch/arm/boot/dts/stih410-b2260.dts
@@ -62,8 +62,11 @@
/* Low speed expansion connector */
uart0: serial@9830000 {
label = "LS-UART0";
- status = "okay";
+ pinctrl-names = "default", "no-hw-flowctrl";
+ pinctrl-0 = <&pinctrl_serial0_hw_flowctrl>;
+ pinctrl-1 = <&pinctrl_serial0>;
rts-gpios = <&pio17 3 GPIO_ACTIVE_LOW>;
+ status = "okay";
};
/* Low speed expansion connector */
--
2.9.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2017-02-03 10:23 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-02-03 10:23 [PATCH v4 00/10] serial: st-asc: Allow handling of RTS lin Lee Jones
2017-02-03 10:23 ` [PATCH v4 01/10] serial: st-asc: Ignore the parity error bit if 8-bit mode is enabled Lee Jones
2017-02-03 10:23 ` [PATCH v4 02/10] serial: st-asc: Provide RTS functionality Lee Jones
2017-02-03 10:23 ` [PATCH v4 03/10] serial: st-asc: Read in all Pinctrl states Lee Jones
2017-02-03 10:23 ` [PATCH v4 04/10] serial: st-asc: (De)Register GPIOD and swap Pinctrl profiles Lee Jones
2017-02-03 10:23 ` [PATCH v4 05/10] serial: st-asc: Use generic DT binding for announcing RTS/CTS lines Lee Jones
[not found] ` <20170203102319.23489-1-lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2017-02-03 10:23 ` [PATCH v4 06/10] dt-bindings: serial: Update 'uart-has-rtscts' description Lee Jones
[not found] ` <20170203102319.23489-7-lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2017-02-08 21:17 ` Rob Herring
2017-02-03 10:23 ` [PATCH v4 07/10] ARM: dts: STiH410-b2260: Identify the UART RTS line Lee Jones
2017-02-03 10:23 ` [PATCH v4 08/10] ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control Lee Jones
2017-02-03 10:23 ` Lee Jones [this message]
2017-02-03 10:23 ` [PATCH v4 10/10] ARM: dts: STiH410-b2260: Enable " Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170203102319.23489-10-lee.jones@linaro.org \
--to=lee.jones-qsej5fyqhm4dnm+yrofe0a@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org \
--cc=jslaby-IBi9RG/b67k@public.gmane.org \
--cc=kernel-F5mvAk5X5gdBDgjK7y7TUQ@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-serial-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=patrice.chotard-qxv4g6HH51o@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).