[PATCH v2 0/8] ARM64: Initial Marvell IAP140 enablement

[PATCH v2 0/8] ARM64: Initial Marvell IAP140 enablement

[Andreas Färber]

Hello,

This series adds initial support for the Marvell IAP140 SoC (aka PXA1908)
and the Andromeda Box Edge development board.

v2 reuses ARCH_MMP.

Both earlycon and serial are working, but an explicit console=ttyS0,115200n8
is needed; with just "earlycon" and stdout-path the earlycon stops early and
switches to a tty0, long before disabling the bootconsole...

All four CPUs come up, and an initrd can be reached.

However, there are errors about CPUs 1-3 having a zero SYS_CNTFRQ_EL0:

[    0.095812] smp: Bringing up secondary CPUs ...
======pxa1908_pmu_core_pwr_on: mpidr = 0x1
======pxa1908_pmu_core_pwr_on: mpidr = 0x2
======pxa1908_pmu_core_pwr_on: mpidr = 0x3
[    0.133419] Detected VIPT I-cache on CPU1
[    0.133430] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU1: 0x00000000000000
[    0.133447] Unsupported CPU feature variation.
...
[    0.133748] CPU1: Booted secondary processor [410fd032]
[    0.165465] Detected VIPT I-cache on CPU2
[    0.165474] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU2: 0x00000000000000
[    0.165505] CPU2: Booted secondary processor [410fd032]
[    0.197539] Detected VIPT I-cache on CPU3
[    0.197546] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU3: 0x00000000000000
[    0.197573] CPU3: Booted secondary processor [410fd032]
[    0.197625] smp: Brought up 1 node, 4 CPUs
[    0.522514] SMP: Total of 4 processors activated.
[    0.527212] CPU features: detected feature: 32-bit EL0 Support
[    0.533105] CPU: All CPU(s) started at EL2

KVM appears to initialize okay, but was not yet tested with guests.

[    0.865255] kvm [1]: 8-bit VMID
[    0.868401] kvm [1]: IDMAP page: d23000
[    0.872233] kvm [1]: HYP VA range: 800000000000:ffffffffffff
[    0.878262] kvm [1]: Hyp mode initialized successfully
[    0.883429] kvm [1]: vgic-v2@d1dfc000
[    0.887179] kvm [1]: vgic interrupt IRQ1
[    0.891120] kvm [1]: virtual timer IRQ4

One limitation is currently the lack of an IAP140 clk driver. Patch 4/4 works
around that for UART0 with a fixed-clock.

A 3.14 based tree is available on GitHub acorn-marvell/brillo_pxa_kernel.

Booting required changes to the vendor U-Boot,
cf. https://en.opensuse.org/HCL:AndromedaBoxEdge

https://github.com/afaerber/linux/commits/edge-next

Have a lot of fun!

Cheers,
Andreas

v1 -> v2:
* Add non-DT documentation
* Use ARCH_MMP instead of ARCH_PXA
* Split off Kconfig cleanups per subsystem
* Drop "mrvl,pxa-uart" and instead implement mmp earlycon
* Add some more DT nodes

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: info@andromedabox.org
Cc: devicetree@vger.kernel.org

Andreas Färber (8):
  Documentation: arm: Marvell: Document IAP140
  tty: serial: Suppress deprecated SERIAL_PXA on arm64
  tty: serial: 8250_pxa: Implement mmp earlycon
  sound: soc: pxa: Suppress SND_MMP_SOC for arm64
  ARM64: Prepare Marvell IAP140 aka PXA1908
  Documentation: devicetree: arm: marvell: Document IAP140
  ARM64: dts: marvell: Add IAP140 and Andromeda Box Edge
  ARM64: dts: marvell: iap140-andromeda-box-edge: Add uart0 clock

 Documentation/arm/Marvell/README                   |  12 +-
 .../devicetree/bindings/arm/marvell/iap140.txt     |  11 +
 arch/arm64/Kconfig.platforms                       |   7 +
 arch/arm64/boot/dts/marvell/Makefile               |   3 +
 .../boot/dts/marvell/iap140-andromeda-box-edge.dts |  87 ++++++++
 arch/arm64/boot/dts/marvell/iap140.dtsi            | 241 +++++++++++++++++++++
 drivers/tty/serial/8250/8250_pxa.c                 |   1 +
 drivers/tty/serial/Kconfig                         |   2 +-
 sound/soc/pxa/Kconfig                              |   4 +-
 9 files changed, 364 insertions(+), 4 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/arm/marvell/iap140.txt
 create mode 100644 arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts
 create mode 100644 arch/arm64/boot/dts/marvell/iap140.dtsi

-- 
2.10.2

[PATCH v2 6/8] Documentation: devicetree: arm: marvell: Document IAP140

[Andreas Färber]

Signed-off-by: Andreas Färber <afaerber-l3A5Bk7waGM@public.gmane.org>
---
 v1 -> v2:
 * Adopted "marvell" vendor prefix (Thomas)
 * Documented Andromeda Box Edge as example
 
 Documentation/devicetree/bindings/arm/marvell/iap140.txt | 11 +++++++++++
 1 file changed, 11 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/marvell/iap140.txt

diff --git a/Documentation/devicetree/bindings/arm/marvell/iap140.txt b/Documentation/devicetree/bindings/arm/marvell/iap140.txt
new file mode 100644
index 0000000..37c6d92
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/iap140.txt
@@ -0,0 +1,11 @@
+Marvell IAP140 Device Tree Bindings
+-----------------------------------
+
+Boards using a SoC of the Marvell IAP140 family must carry the following
+root node property:
+
+ - compatible :  must contain "marvell,iap140"
+
+Example:
+
+    compatible = "marvell,andromeda-box-edge", "marvell,iap140";
-- 
2.10.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 7/8] ARM64: dts: marvell: Add IAP140 and Andromeda Box Edge

[Andreas Färber]

PPI interrupts 11, 10, 9 are guesses, and so are the second two memory
regions of the GIC.

Signed-off-by: Andreas Färber <afaerber-l3A5Bk7waGM@public.gmane.org>
---
 v1 -> v2:
 * Updated for ARCH_MMP, added Makefile comment
 * Adopted "marvell" vendor prefix (Thomas)
 * Disabled smmu in .dtsi, re-enabled in .dts
 * Enabled asram node
 * Added adma, timer, pinctrl nodes
 
 arch/arm64/boot/dts/marvell/Makefile               |   3 +
 .../boot/dts/marvell/iap140-andromeda-box-edge.dts |  80 +++++++
 arch/arm64/boot/dts/marvell/iap140.dtsi            | 241 +++++++++++++++++++++
 3 files changed, 324 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts
 create mode 100644 arch/arm64/boot/dts/marvell/iap140.dtsi

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 3e6ce6c..fa1bf06 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -2,6 +2,9 @@
 dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-dmp.dtb
 dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-stb.dtb
 
+# MMP SoC Family
+dtb-$(CONFIG_ARCH_MMP) += iap140-andromeda-box-edge.dtb
+
 # Mvebu SoC Family
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
diff --git a/arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts b/arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts
new file mode 100644
index 0000000..0b0b150
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts
@@ -0,0 +1,80 @@
+/*
+ * Copyright (c) 2016-2017 Andreas Färber
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+/memreserve/ 0x09000000 0x01000000;
+/memreserve/ 0x0a000000 0x00080000;
+
+#include "iap140.dtsi"
+
+/ {
+	compatible = "marvell,andromeda-box-edge", "marvell,iap140";
+	model = "Andromeda Box Edge";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+};
+
+&pmx {
+	pinctrl-single,gpio-range = <&range 55 55 0>,
+	                            <&range 110 32 0>,
+	                            <&range 52 1 0>;
+};
+
+&smmu {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/iap140.dtsi b/arch/arm64/boot/dts/marvell/iap140.dtsi
new file mode 100644
index 0000000..a0cefa6
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/iap140.dtsi
@@ -0,0 +1,241 @@
+/*
+ * Copyright (c) 2016-2017 Andreas Färber
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "marvell,iap140";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		smmu: iommu@c0010000 {
+			compatible = "arm,mmu-400";
+			reg = <0x0 0xc0010000 0x0 0x10000>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+			             <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		adma: dma-controller@d128d800 {
+			compatible = "marvell,adma-1.0";
+			reg = <0x0 0xd128d800 0x0 0x100>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			asram = <&asram>;
+		};
+
+		asram: sram@d12a0000 {
+			compatible = "mmio-sram";
+			reg = <0x0 0xd12a0000 0x0 0x10000>;
+		};
+
+		gic: interrupt-controller@d1df9000 {
+			compatible = "arm,gic-400";
+			reg = <0x0 0xd1df9000 0x0 0x1000>,
+			      <0x0 0xd1dfa000 0x0 0x2000>,
+			      <0x0 0xd1dfc000 0x0 0x2000>,
+			      <0x0 0xd1dfe000 0x0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		apb@d4000000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xd4000000 0x0 0x00200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0xd4000000 0x00200000>;
+
+			pdma: dma-controller@0 {
+				compatible = "marvell,pdma-1.0";
+				reg = <0x0 0x10000>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				#dma-cells = <2>;
+				#dma-channels = <30>;
+			};
+
+			timer0: timer@14000 {
+				compatible = "mrvl,mmp-timer";
+				reg = <0x14000 0xc8>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				             <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			timer1: timer@16000 {
+				compatible = "mrvl,mmp-timer";
+				reg = <0x16000 0xc8>;
+				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				             <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			uart0: serial@17000 {
+				compatible = "mrvl,mmp-uart";
+				reg = <0x17000 0x1000>;
+				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&pdma 21 1>,
+				       <&pdma 22 1>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			uart1: serial@18000 {
+				compatible = "mrvl,mmp-uart";
+				reg = <0x18000 0x1000>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&pdma 23 1>,
+				       <&pdma 24 1>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			pmx: pinmux@1e000 {
+				compatible = "pinconf-single";
+				reg = <0x1e000 0x330>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#gpio-range-cells = <3>;
+				ranges;
+
+				#pinctrl-cells = <1>;
+				pinctrl-single,register-width = <32>;
+				pinctrl-single,function-mask = <7>;
+
+				range: gpio-range {
+					#pinctrl-single,gpio-range-cells = <3>;
+				};
+			};
+
+			timer2: timer@1f000 {
+				compatible = "mrvl,mmp-timer";
+				reg = <0x1f000 0xc8>;
+				status = "disabled";
+			};
+
+			uart2: serial@36000 {
+				compatible = "mrvl,mmp-uart";
+				reg = <0x36000 0x1000>;
+				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&pdma 4 1>,
+				       <&pdma 5 1>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+		};
+
+		axi@d4200000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xd4200000 0x0 0x00200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0xd4200000 0x00200000>;
+		};
+	};
+};
-- 
2.10.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 8/8] ARM64: dts: marvell: iap140-andromeda-box-edge: Add uart0 clock

[Andreas Färber]

Use a fixed clock to enable ttyS0 output.

Signed-off-by: Andreas Färber <afaerber@suse.de>
---
 v1 -> v2: unchanged
 
 arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts b/arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts
index 0b0b150..15ad0f3 100644
--- a/arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts
+++ b/arch/arm64/boot/dts/marvell/iap140-andromeda-box-edge.dts
@@ -63,6 +63,12 @@
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
 	};
+
+	uart0_clk: uart0-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <14740000>;
+		#clock-cells = <0>;
+	};
 };
 
 &pmx {
@@ -77,4 +83,5 @@
 
 &uart0 {
 	status = "okay";
+	clocks = <&uart0_clk>;
 };
-- 
2.10.2

Re: [PATCH v2 0/8] ARM64: Initial Marvell IAP140 enablement

[Rob Herring]

On Tue, Feb 21, 2017 at 8:29 PM, Andreas Färber <afaerber-l3A5Bk7waGM@public.gmane.org> wrote:
> Hello,
>
> This series adds initial support for the Marvell IAP140 SoC (aka PXA1908)
> and the Andromeda Box Edge development board.
>
> v2 reuses ARCH_MMP.
>
> Both earlycon and serial are working, but an explicit console=ttyS0,115200n8
> is needed; with just "earlycon" and stdout-path the earlycon stops early and
> switches to a tty0, long before disabling the bootconsole...
>
> All four CPUs come up, and an initrd can be reached.
>
> However, there are errors about CPUs 1-3 having a zero SYS_CNTFRQ_EL0:
>
> [    0.095812] smp: Bringing up secondary CPUs ...
> ======pxa1908_pmu_core_pwr_on: mpidr = 0x1
> ======pxa1908_pmu_core_pwr_on: mpidr = 0x2
> ======pxa1908_pmu_core_pwr_on: mpidr = 0x3
> [    0.133419] Detected VIPT I-cache on CPU1
> [    0.133430] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU1: 0x00000000000000
> [    0.133447] Unsupported CPU feature variation.
> ...
> [    0.133748] CPU1: Booted secondary processor [410fd032]
> [    0.165465] Detected VIPT I-cache on CPU2
> [    0.165474] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU2: 0x00000000000000
> [    0.165505] CPU2: Booted secondary processor [410fd032]
> [    0.197539] Detected VIPT I-cache on CPU3
> [    0.197546] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU3: 0x00000000000000
> [    0.197573] CPU3: Booted secondary processor [410fd032]
> [    0.197625] smp: Brought up 1 node, 4 CPUs
> [    0.522514] SMP: Total of 4 processors activated.
> [    0.527212] CPU features: detected feature: 32-bit EL0 Support
> [    0.533105] CPU: All CPU(s) started at EL2
>
> KVM appears to initialize okay, but was not yet tested with guests.
>
> [    0.865255] kvm [1]: 8-bit VMID
> [    0.868401] kvm [1]: IDMAP page: d23000
> [    0.872233] kvm [1]: HYP VA range: 800000000000:ffffffffffff
> [    0.878262] kvm [1]: Hyp mode initialized successfully
> [    0.883429] kvm [1]: vgic-v2@d1dfc000
> [    0.887179] kvm [1]: vgic interrupt IRQ1
> [    0.891120] kvm [1]: virtual timer IRQ4
>
> One limitation is currently the lack of an IAP140 clk driver. Patch 4/4 works
> around that for UART0 with a fixed-clock.

The PXA1928 clock driver should be close to what you need. They are
supposed to be very similar.

> A 3.14 based tree is available on GitHub acorn-marvell/brillo_pxa_kernel.
>
> Booting required changes to the vendor U-Boot,
> cf. https://en.opensuse.org/HCL:AndromedaBoxEdge
>
> https://github.com/afaerber/linux/commits/edge-next
>
> Have a lot of fun!
>
> Cheers,
> Andreas
>
> v1 -> v2:
> * Add non-DT documentation
> * Use ARCH_MMP instead of ARCH_PXA
> * Split off Kconfig cleanups per subsystem
> * Drop "mrvl,pxa-uart" and instead implement mmp earlycon
> * Add some more DT nodes
>
> Cc: Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> Cc: Gregory Clement <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> Cc: info-PWLG29+z7hGxBmiGZ5/UTQ@public.gmane.org
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>
> Andreas Färber (8):
>   Documentation: arm: Marvell: Document IAP140
>   tty: serial: Suppress deprecated SERIAL_PXA on arm64
>   tty: serial: 8250_pxa: Implement mmp earlycon

You should not use the pxa serial driver. AFAICT, it was separate to
add DMA support, but now the base 8250 driver supports DMA. The base
8250 driver works with the PXA1928 and should also work with the
PXA1908.

>   sound: soc: pxa: Suppress SND_MMP_SOC for arm64
>   ARM64: Prepare Marvell IAP140 aka PXA1908
>   Documentation: devicetree: arm: marvell: Document IAP140
>   ARM64: dts: marvell: Add IAP140 and Andromeda Box Edge
>   ARM64: dts: marvell: iap140-andromeda-box-edge: Add uart0 clock
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 0/8] ARM64: Initial Marvell IAP140 enablement

[Andreas Färber]

Hi Rob,

Am 22.02.2017 um 14:34 schrieb Rob Herring:
> On Tue, Feb 21, 2017 at 8:29 PM, Andreas Färber <afaerber-l3A5Bk7waGM@public.gmane.org> wrote:
>> One limitation is currently the lack of an IAP140 clk driver. Patch 4/4 works
>> around that for UART0 with a fixed-clock.
> 
> The PXA1928 clock driver should be close to what you need. They are
> supposed to be very similar.

Where do you see that in mainline? Not in drivers/clk/pxa/ at least. I'm
certain the acorn-marvell tree has a PXA1908 clk driver somewhere, too,
I just haven't ported it yet.

>> Andreas Färber (8):
>>   Documentation: arm: Marvell: Document IAP140
>>   tty: serial: Suppress deprecated SERIAL_PXA on arm64
>>   tty: serial: 8250_pxa: Implement mmp earlycon
> 
> You should not use the pxa serial driver. AFAICT, it was separate to
> add DMA support, but now the base 8250 driver supports DMA. The base
> 8250 driver works with the PXA1928 and should also work with the
> PXA1908.

Do you personally have one? I didn't spot a pxa1928 DT in mainline.

So, by my reading both 8250_of.c and 8250_pxa.c list "mrvl,mmp-uart" for
the platform driver. Is that really intentional?

What the early_pxa earlycon does is set the register shift and then
reuse the 8250 core - that looks perfectly valid to me. Are you possibly
mixing that up with the non-8250 pxa serial driver that I am already
suppressing one patch earlier?

While at it, are you aware that we have two drivers, one pxa and one
mmp, that bind to "marvell,pdma-1.0"? That seemed wrong to me, too.

Regards,
Andreas

-- 
SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer, Jane Smithard, Graham Norton
HRB 21284 (AG Nürnberg)
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 0/8] ARM64: Initial Marvell IAP140 enablement

[Andreas Färber]

Am 22.02.2017 um 17:43 schrieb Andreas Färber:
> Hi Rob,
> 
> Am 22.02.2017 um 14:34 schrieb Rob Herring:
>> On Tue, Feb 21, 2017 at 8:29 PM, Andreas Färber <afaerber-l3A5Bk7waGM@public.gmane.org> wrote:
>>> One limitation is currently the lack of an IAP140 clk driver. Patch 4/4 works
>>> around that for UART0 with a fixed-clock.
>>
>> The PXA1928 clock driver should be close to what you need. They are
>> supposed to be very similar.
> 
> Where do you see that in mainline? Not in drivers/clk/pxa/ at least. I'm
> certain the acorn-marvell tree has a PXA1908 clk driver somewhere, too,
> I just haven't ported it yet.
> 
>>> Andreas Färber (8):
>>>   Documentation: arm: Marvell: Document IAP140
>>>   tty: serial: Suppress deprecated SERIAL_PXA on arm64
>>>   tty: serial: 8250_pxa: Implement mmp earlycon
>>
>> You should not use the pxa serial driver. AFAICT, it was separate to
>> add DMA support, but now the base 8250 driver supports DMA. The base
>> 8250 driver works with the PXA1928 and should also work with the
>> PXA1908.
> 
> Do you personally have one? I didn't spot a pxa1928 DT in mainline.
> 
> So, by my reading both 8250_of.c and 8250_pxa.c list "mrvl,mmp-uart" for
> the platform driver. Is that really intentional?
> 
> What the early_pxa earlycon does is set the register shift and then
> reuse the 8250 core - that looks perfectly valid to me. Are you possibly
> mixing that up with the non-8250 pxa serial driver that I am already
> suppressing one patch earlier?

Hit send too early: There's also 8250_early.c, but that does not appear
to use the reg-shift property (which is not mentioned in the
mrvl,mmp-uart binding) and thus omap has a custom earlycon driver there,
similar to what is in 8250_pxa.c.

> 
> While at it, are you aware that we have two drivers, one pxa and one
> mmp, that bind to "marvell,pdma-1.0"? That seemed wrong to me, too.
> 
> Regards,
> Andreas
> 


-- 
SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer, Jane Smithard, Graham Norton
HRB 21284 (AG Nürnberg)
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 0/8] ARM64: Initial Marvell IAP140 enablement

[Rob Herring]

On Wed, Feb 22, 2017 at 10:43 AM, Andreas Färber <afaerber@suse.de> wrote:
> Hi Rob,
>
> Am 22.02.2017 um 14:34 schrieb Rob Herring:
>> On Tue, Feb 21, 2017 at 8:29 PM, Andreas Färber <afaerber@suse.de> wrote:
>>> One limitation is currently the lack of an IAP140 clk driver. Patch 4/4 works
>>> around that for UART0 with a fixed-clock.
>>
>> The PXA1928 clock driver should be close to what you need. They are
>> supposed to be very similar.
>
> Where do you see that in mainline? Not in drivers/clk/pxa/ at least. I'm
> certain the acorn-marvell tree has a PXA1908 clk driver somewhere, too,
> I just haven't ported it yet.

drivers/clk/mmp/clk-of-pxa1928.c

I ported/rewrote that from Marvell's 3.10 vendor tree.

>>> Andreas Färber (8):
>>>   Documentation: arm: Marvell: Document IAP140
>>>   tty: serial: Suppress deprecated SERIAL_PXA on arm64
>>>   tty: serial: 8250_pxa: Implement mmp earlycon
>>
>> You should not use the pxa serial driver. AFAICT, it was separate to
>> add DMA support, but now the base 8250 driver supports DMA. The base
>> 8250 driver works with the PXA1928 and should also work with the
>> PXA1908.
>
> Do you personally have one? I didn't spot a pxa1928 DT in mainline.

Yes. It never got released and got abandoned. I got several drivers
cleaned up to support it and the clock code in before that happened. I
had a in-progress DRM driver too. I was debugging why some monitors
worked and others didn't when I stopped working on it. I think the
board you are working on has the same ADV7533?

It's all up on my Linaro tree:
https://git.linaro.org/people/rob.herring/linux.git

> So, by my reading both 8250_of.c and 8250_pxa.c list "mrvl,mmp-uart" for
> the platform driver. Is that really intentional?

Humm, well I added support in commit 6ad991b699b4e to of_serial.c and
then it looks like it got copied to 8250_pxa.c recently. Not sure if
that really made sense or not. We should remove one of them.
8250_pxa.c looks fairly pointless to me. Turning a clock on/off in
resume/suspend is already supported by 8250_of.c (which doesn't have
the bug of turning off the console's clock in suspend). The only other
thing is the errata in serial_pxa_dl_write.

> What the early_pxa earlycon does is set the register shift and then
> reuse the 8250 core - that looks perfectly valid to me. Are you possibly
> mixing that up with the non-8250 pxa serial driver that I am already
> suppressing one patch earlier?

The earlycon core already sets up reg-shift for you.

I added earlycon support in commit a4c639b04f301d. I used "ns16650a"
as a fallback compatible string, so there's not an explicit PXA/MMP
compatible string there.

> While at it, are you aware that we have two drivers, one pxa and one
> mmp, that bind to "marvell,pdma-1.0"? That seemed wrong to me, too.

Yeah, it was drivers/tty/serial/pxa.c that I was thinking of. I was
incorrectly thinking 8250_pxa.c was that one.

Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 6/8] Documentation: devicetree: arm: marvell: Document IAP140

[Rob Herring]

On Wed, Feb 22, 2017 at 03:29:26AM +0100, Andreas Färber wrote:
> Signed-off-by: Andreas Färber <afaerber@suse.de>
> ---
>  v1 -> v2:
>  * Adopted "marvell" vendor prefix (Thomas)
>  * Documented Andromeda Box Edge as example
>  
>  Documentation/devicetree/bindings/arm/marvell/iap140.txt | 11 +++++++++++
>  1 file changed, 11 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/arm/marvell/iap140.txt

Acked-by: Rob Herring <robh@kernel.org>