[PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

From: Rafał Miłecki <rafal@milecki.pl>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
uses 3 x BCM4366 chipsets for wireless.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
---
 arch/arm/boot/dts/Makefile                    |  1 +
 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts | 36 +++++++++++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 52a05289c538..931db0b41246 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-netgear-r8000.dtb \
 	bcm4709-tplink-archer-c9-v1.dtb \
 	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-linksys-ea9500.dtb \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm94708.dtb \
diff --git a/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts b/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts
new file mode 100644
index 000000000000..31639e5b8c72
--- /dev/null
+++ b/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Linksys EA9500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
-- 
2.11.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Imre Kaloz]

Hi Rafal,

As discussed for other platforms as well, please use the board's name as 
the same board can end up being sold under multiple model numbers.

So please rename the file to bcm47094-linksys-panamera.dts


Best,

Imre


On 2017-02-23 11:40, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
>
> It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
> uses 3 x BCM4366 chipsets for wireless.
>
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
> ---
>  arch/arm/boot/dts/Makefile                    |  1 +
>  arch/arm/boot/dts/bcm47094-linksys-ea9500.dts | 36 +++++++++++++++++++++++++++
>  2 files changed, 37 insertions(+)
>  create mode 100644 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 52a05289c538..931db0b41246 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
>  	bcm4709-netgear-r8000.dtb \
>  	bcm4709-tplink-archer-c9-v1.dtb \
>  	bcm47094-dlink-dir-885l.dtb \
> +	bcm47094-linksys-ea9500.dtb \
>  	bcm47094-luxul-xwr-3100.dtb \
>  	bcm47094-netgear-r8500.dtb \
>  	bcm94708.dtb \
> diff --git a/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts b/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts
> new file mode 100644
> index 000000000000..31639e5b8c72
> --- /dev/null
> +++ b/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts
> @@ -0,0 +1,36 @@
> +/*
> + * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
> + *
> + * Licensed under the ISC license.
> + */
> +
> +/dts-v1/;
> +
> +#include "bcm47094.dtsi"
> +#include "bcm5301x-nand-cs0-bch8.dtsi"
> +
> +/ {
> +	compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708";
> +	model = "Linksys EA9500";
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200";
> +	};
> +
> +	memory {
> +		reg = <0x00000000 0x08000000
> +		       0x88000000 0x08000000>;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		wps {
> +			label = "WPS";
> +			linux,code = <KEY_WPS_BUTTON>;
> +			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

On 23 February 2017 at 13:27, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
> As discussed for other platforms as well, please use the board's name as the
> same board can end up being sold under multiple model numbers.
>
> So please rename the file to bcm47094-linksys-panamera.dts

Huh? Where did you get panamera name from?!
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Imre Kaloz]

Dear Rafal,

On 2017-02-23 13:29, Rafał Miłecki wrote:
> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote:
>> As discussed for other platforms as well, please use the board's name as the
>> same board can end up being sold under multiple model numbers.
>>
>> So please rename the file to bcm47094-linksys-panamera.dts
> Huh? Where did you get panamera name from?!
Your manners shine on these dark days of winter. For about a decade now, 
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information 
if you are too lazy to look into the GPL tarball or at the original 
bootlogs.


Best,

Imre

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

On 23 February 2017 at 13:44, Imre Kaloz <kaloz@openwrt.org> wrote:
> On 2017-02-23 13:29, Rafał Miłecki wrote:
>>
>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote:
>>>
>>> As discussed for other platforms as well, please use the board's name as
>>> the
>>> same board can end up being sold under multiple model numbers.
>>>
>>> So please rename the file to bcm47094-linksys-panamera.dts
>>
>> Huh? Where did you get panamera name from?!
>
> Your manners shine on these dark days of winter. For about a decade now,
> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
> you are too lazy to look into the GPL tarball or at the original bootlogs.

Sadly Linksys doesn't sponsor me or provide me any hardware. The
bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.

-- 
Rafał

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.

Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
---
V2: Use panamera board name
---
 arch/arm/boot/dts/Makefile                      |  1 +
 arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 36 +++++++++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-linksys-panamera.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 52a05289c538..2feabbe16d53 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-netgear-r8000.dtb \
 	bcm4709-tplink-archer-c9-v1.dtb \
 	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-linksys-panamera.dtb \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm94708.dtb \
diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
new file mode 100644
index 000000000000..31639e5b8c72
--- /dev/null
+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2017 Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Linksys EA9500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
-- 
2.11.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

On 23 February 2017 at 13:51, Rafał Miłecki <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> On 23 February 2017 at 13:44, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
>> On 2017-02-23 13:29, Rafał Miłecki wrote:
>>>
>>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
>>>>
>>>> As discussed for other platforms as well, please use the board's name as
>>>> the
>>>> same board can end up being sold under multiple model numbers.
>>>>
>>>> So please rename the file to bcm47094-linksys-panamera.dts
>>>
>>> Huh? Where did you get panamera name from?!
>>
>> Your manners shine on these dark days of winter. For about a decade now,
>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
>> you are too lazy to look into the GPL tarball or at the original bootlogs.
>
> Sadly Linksys doesn't sponsor me or provide me any hardware. The
> bootlogs I found:
> https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
> http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
> didn't include board name. As you probably can guess
> http://192.168.1.1/ was useful in my case as well.

Or rather "useless" ;)

-- 
Rafał
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Imre Kaloz]

Dear Rafal,

On 2017-02-23 13:51, Rafał Miłecki wrote:
> On 23 February 2017 at 13:44, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
>> On 2017-02-23 13:29, Rafał Miłecki wrote:
>>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
>>>> As discussed for other platforms as well, please use the board's name as
>>>> the
>>>> same board can end up being sold under multiple model numbers.
>>>>
>>>> So please rename the file to bcm47094-linksys-panamera.dts
>>> Huh? Where did you get panamera name from?!
>> Your manners shine on these dark days of winter. For about a decade now,
>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
>> you are too lazy to look into the GPL tarball or at the original bootlogs.
> Sadly Linksys doesn't sponsor me or provide me any hardware. The
> bootlogs I found:
> https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
> http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
> didn't include board name. As you probably can guess
> http://192.168.1.1/ was useful in my case as well.
>

I've guessed you have the hardware - so you're submitting dts files 
without testing it? I know they don't do much, but still, this is an 
interesting concept.

Anyways, if you are just adding support for hardware blindly, the dd-wrt 
forum you've mentioned has other posts that might help you [1].


Best,

Imre

[1] http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1062050
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH V2] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Imre Kaloz]

Dear Rafal,

On 2017-02-23 13:56, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
>
> It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
> uses 3 x BCM4366 chipsets for wireless.
> Panamera seems to be board name used by Linksys.
>
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
> ---
> V2: Use panamera board name

My bad, forgot to mention that you should also use "linksys,panamera" as 
a compatibility name as well. "model" should stay as-is of course.



Best,

Imre

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

On 23 February 2017 at 13:59, Imre Kaloz <kaloz@openwrt.org> wrote:
> On 2017-02-23 13:51, Rafał Miłecki wrote:
>>
>> On 23 February 2017 at 13:44, Imre Kaloz <kaloz@openwrt.org> wrote:
>>>
>>> On 2017-02-23 13:29, Rafał Miłecki wrote:
>>>>
>>>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote:
>>>>>
>>>>> As discussed for other platforms as well, please use the board's name
>>>>> as
>>>>> the
>>>>> same board can end up being sold under multiple model numbers.
>>>>>
>>>>> So please rename the file to bcm47094-linksys-panamera.dts
>>>>
>>>> Huh? Where did you get panamera name from?!
>>>
>>> Your manners shine on these dark days of winter. For about a decade now,
>>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information
>>> if
>>> you are too lazy to look into the GPL tarball or at the original
>>> bootlogs.
>>
>> Sadly Linksys doesn't sponsor me or provide me any hardware. The
>> bootlogs I found:
>> https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
>> http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
>> didn't include board name. As you probably can guess
>> http://192.168.1.1/ was useful in my case as well.
>>
>
> I've guessed you have the hardware - so you're submitting dts files without
> testing it? I know they don't do much, but still, this is an interesting
> concept.

I'm sending what was tested by EA9500 user:
https://forum.lede-project.org/t/lede-tested-on-linksys-ea9500/1612

I'm planning to add better support for this device, but it requires
extra testing which may take some time. So I just started with what I
can provide so far.

-- 
Rafał

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

On 23 February 2017 at 14:03, Imre Kaloz <kaloz@openwrt.org> wrote:
> On 2017-02-23 13:56, Rafał Miłecki wrote:
>>
>> From: Rafał Miłecki <rafal@milecki.pl>
>>
>> It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
>> uses 3 x BCM4366 chipsets for wireless.
>> Panamera seems to be board name used by Linksys.
>>
>> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
>> ---
>> V2: Use panamera board name
>
>
> My bad, forgot to mention that you should also use "linksys,panamera" as a
> compatibility name as well. "model" should stay as-is of course.

Oops, I missed that. You're correct obviously.

-- 
Rafał

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V3] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

From: Rafał Miłecki <rafal@milecki.pl>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
---
 arch/arm/boot/dts/Makefile                      |  1 +
 arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 36 +++++++++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-linksys-panamera.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 52a05289c538..2feabbe16d53 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-netgear-r8000.dtb \
 	bcm4709-tplink-archer-c9-v1.dtb \
 	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-linksys-panamera.dtb \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm94708.dtb \
diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
new file mode 100644
index 000000000000..b6750f70dffb
--- /dev/null
+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,panamera", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Linksys EA9500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
-- 
2.11.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

On 23 February 2017 at 13:44, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
> On 2017-02-23 13:29, Rafał Miłecki wrote:
>>
>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
>>>
>>> As discussed for other platforms as well, please use the board's name as
>>> the
>>> same board can end up being sold under multiple model numbers.
>>>
>>> So please rename the file to bcm47094-linksys-panamera.dts
>>
>> Huh? Where did you get panamera name from?!
>
> Your manners shine on these dark days of winter. For about a decade now,
> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
> you are too lazy to look into the GPL tarball or at the original bootlogs.

Today I decided to do my homework & check GPL sources of EA9500 fw.

I grepped them for panamera and I found this name in few files:
./checkpatches
./src/mod_bdutil/platform/brcm/usbhub.h
./src/mod_bdutil/platform/brcm/buttons.h
./src/mod_bdutil/platform/brcm/usbhub.c
./src/mod_bdutil/platform/brcm/leds_panamera.c
./src/mod_bdutil/platform/brcm/leds.c
./src/mod_bdutil/bdutil.h.panamera
./src/mod_bdutil/Makefile.panamera

Unfortunately all these results aren't very clear for getting board
name of EA9500. I checked them and panamera is only one of listed
boards there. E.g. checkpatches contains following lines:
# patched by BRCM for Panamera
# patched by BRCM for F70
# patched by BRCM for Pinnacles
# patched by BRCM for EA9200

So EA9500 board name could be any of above.

Similarly there are following Makefiles in EA9500 GPL package:
Makefile.audi
Makefile.bentley
Makefile.blk-mamba
Makefile.carrera
Makefile.esprit
Makefile.f70
Makefile.focus
Makefile.honda
Makefile.impala
Makefile.lemans
Makefile.mamba
Makefile.panamera
Makefile.pub
Makefile.r8
Makefile.spyder
Makefile.taurus
Makefile.viper
Makefile.viperuivm
Makefile.wraith

So again, any of these name could be EA9500 board name.

Will you be so generous to tell us how did you get EA9500 board name
by just looking at GPL sources?

-- 
Rafał
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

On 24 February 2017 at 07:02, Rafał Miłecki <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> On 23 February 2017 at 13:44, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
>> On 2017-02-23 13:29, Rafał Miłecki wrote:
>>>
>>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
>>>>
>>>> As discussed for other platforms as well, please use the board's name as
>>>> the
>>>> same board can end up being sold under multiple model numbers.
>>>>
>>>> So please rename the file to bcm47094-linksys-panamera.dts
>>>
>>> Huh? Where did you get panamera name from?!
>>
>> Your manners shine on these dark days of winter. For about a decade now,
>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
>> you are too lazy to look into the GPL tarball or at the original bootlogs.
>
> Today I decided to do my homework & check GPL sources of EA9500 fw.
>
> (...)
>
> Will you be so generous to tell us how did you get EA9500 board name
> by just looking at GPL sources?

I also tried find with -name "*panamera*". One way of guessing board
name seems to be checking names of patches in ./src/linux/patches/.
Any other, more reliable method?

-- 
Rafał
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Imre Kaloz]

Dear Rafal,

On 2017-02-24 07:10, Rafał Miłecki wrote:
>>> Your manners shine on these dark days of winter. For about a decade now,
>>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
>>> you are too lazy to look into the GPL tarball or at the original bootlogs.
>> Today I decided to do my homework & check GPL sources of EA9500 fw.
>>
>> (...)
>>
>> Will you be so generous to tell us how did you get EA9500 board name
>> by just looking at GPL sources?
> I also tried find with -name "*panamera*". One way of guessing board
> name seems to be checking names of patches in ./src/linux/patches/.
> Any other, more reliable method?
>

First of all, it's really weird you never ever looked at the factory 
bootlogs, but let me help in hope to enhance your communication style:

filenames:

src/linux/patches/linux-2.6.36.4-panamera_000_BSP.patch
src/linux/patches/linux-2.6.36.4-panamera_001_brcm_build.patch
src/linux/patches/linux-2.6.36.4-panamera_002_brcm_build_flags_temp_fix.patch
src/linux/patches/linux-2.6.36.4-panamera_003_ctf_bypass.patch
src/linux/patches/linux-2.6.36.4-panamera_006_cisco_comment.patch
src/linux/patches/linux-2.6.36.4-panamera_007_usb_remove_oops.patch
src/linux/patches/linux-2.6.36.4-panamera_008_6rd_sit_fragment.patch
src/linux/patches/linux-2.6.36.4-panamera_009_cisco_rtsp_conntrack.patch
src/linux/patches/linux-2.6.36.4-panamera_010_cisco_rtsp_conntrack2.patch
src/linux/patches/linux-2.6.36.4-panamera_014_ftp_pasv_command.patch
src/linux/patches/linux-2.6.36.4-panamera_046_sip_alg.patch
src/linux/patches/linux-2.6.36.4-panamera_047_add_usb_led.patch
src/linux/patches/linux-2.6.36.4-panamera_050_PPTP_L2TP_ctf.patch
src/linux/patches/linux-2.6.36.4-panamera_052_cfe_pass_led_to_blink.patch
src/linux/patches/linux-2.6.36.4-panamera_201_brcm_patch_20160226.patch

file contents:

src/mod_bdutil/platform/brcm/.board_id.o.cmd
src/mod_bdutil/platform/brcm/.buttons.o.cmd
src/mod_bdutil/platform/brcm/.leds_panamera.o.cmd
src/mod_bdutil/platform/brcm/.usbhub.o.cmd


If you have further questions, feel free to mail me directly and keep 
off-topic discussion away from the lists.


Thank you and have a nice weekend,

Imre

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Rafał Miłecki]

On 25 February 2017 at 23:43, Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org> wrote:
> On 2017-02-24 07:10, Rafał Miłecki wrote:
>>>>
>>>> Your manners shine on these dark days of winter. For about a decade now,
>>>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information
>>>> if
>>>> you are too lazy to look into the GPL tarball or at the original
>>>> bootlogs.
>>>
>>> Today I decided to do my homework & check GPL sources of EA9500 fw.
>>>
>>> (...)
>>>
>>> Will you be so generous to tell us how did you get EA9500 board name
>>> by just looking at GPL sources?
>>
>> I also tried find with -name "*panamera*". One way of guessing board
>> name seems to be checking names of patches in ./src/linux/patches/.
>> Any other, more reliable method?
>>
>
> First of all, it's really weird you never ever looked at the factory
> bootlogs, but let me help in hope to enhance your communication style:
>
> filenames:
>
> src/linux/patches/linux-2.6.36.4-panamera_000_BSP.patch
> src/linux/patches/linux-2.6.36.4-panamera_001_brcm_build.patch
> src/linux/patches/linux-2.6.36.4-panamera_002_brcm_build_flags_temp_fix.patch
> src/linux/patches/linux-2.6.36.4-panamera_003_ctf_bypass.patch
> src/linux/patches/linux-2.6.36.4-panamera_006_cisco_comment.patch
> src/linux/patches/linux-2.6.36.4-panamera_007_usb_remove_oops.patch
> src/linux/patches/linux-2.6.36.4-panamera_008_6rd_sit_fragment.patch
> src/linux/patches/linux-2.6.36.4-panamera_009_cisco_rtsp_conntrack.patch
> src/linux/patches/linux-2.6.36.4-panamera_010_cisco_rtsp_conntrack2.patch
> src/linux/patches/linux-2.6.36.4-panamera_014_ftp_pasv_command.patch
> src/linux/patches/linux-2.6.36.4-panamera_046_sip_alg.patch
> src/linux/patches/linux-2.6.36.4-panamera_047_add_usb_led.patch
> src/linux/patches/linux-2.6.36.4-panamera_050_PPTP_L2TP_ctf.patch
> src/linux/patches/linux-2.6.36.4-panamera_052_cfe_pass_led_to_blink.patch
> src/linux/patches/linux-2.6.36.4-panamera_201_brcm_patch_20160226.patch
>
> file contents:
>
> src/mod_bdutil/platform/brcm/.board_id.o.cmd
> src/mod_bdutil/platform/brcm/.buttons.o.cmd
> src/mod_bdutil/platform/brcm/.leds_panamera.o.cmd
> src/mod_bdutil/platform/brcm/.usbhub.o.cmd
>
>
> If you have further questions, feel free to mail me directly and keep
> off-topic discussion away from the lists.

Thanks

-- 
Rafał
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH V3] ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

[Florian Fainelli]

On 02/23/2017 05:06 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
> 
> It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
> uses 3 x BCM4366 chipsets for wireless.
> Panamera seems to be board name used by Linksys.
> 
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

Applied, thanks!
-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel