[PATCH v2 1/4] gpio: mvebu: Add limited PWM support

[PATCH v2 1/4] gpio: mvebu: Add limited PWM support

[Ralph Sennhauser]

From: Andrew Lunn <andrew@lunn.ch>

Armada 370/XP devices can 'blink' gpio lines with a configurable on
and off period. This can be modelled as a PWM.

However, there are only two sets of PWM configuration registers for
all the gpio lines. This driver simply allows a single gpio line per
gpio chip of 32 lines to be used as a PWM. Attempts to use more return
EBUSY.

Due to the interleaving of registers it is not simple to separate the
PWM driver from the gpio driver. Thus the gpio driver has been
extended with a PWM driver.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
URL: https://patchwork.ozlabs.org/patch/427287/
URL: https://patchwork.ozlabs.org/patch/427295/
[Ralph Sennhauser:
  * port forward
  * merge pwm portion into gpio-mvebu.c
  * merge documentation patch
  * update MAINTAINERS]
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
---
 .../devicetree/bindings/gpio/gpio-mvebu.txt        |  31 +++
 MAINTAINERS                                        |   2 +
 drivers/gpio/gpio-mvebu.c                          | 291 +++++++++++++++++++--
 3 files changed, 307 insertions(+), 17 deletions(-)

diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
index a6f3bec..86932e3 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
@@ -38,6 +38,23 @@ Required properties:
 - #gpio-cells: Should be two. The first cell is the pin number. The
   second cell is reserved for flags, unused at the moment.
 
+Optional properties:
+
+In order to use the gpio lines in PWM mode, some additional optional
+properties are required. Only Armada 370 and XP support these properties.
+
+- reg: an additional register set is needed, for the GPIO Blink
+  Counter on/off registers.
+
+- reg-names: Must contain an entry "pwm" corresponding to the
+  additional register range needed for pwm operation.
+
+- #pwm-cells: Should be two. The first cell is the pin number. The
+  second cell is reserved for flags and should be set to 0, so it has a
+  known value. It then becomes possible to use it in the future.
+
+- clocks: Must be a phandle to the clock for the gpio controller.
+
 Example:
 
 		gpio0: gpio@d0018100 {
@@ -51,3 +68,17 @@ Example:
 			#interrupt-cells = <2>;
 			interrupts = <16>, <17>, <18>, <19>;
 		};
+
+		gpio1: gpio@18140 {
+			compatible = "marvell,orion-gpio";
+			reg = <0x18140 0x40>, <0x181c8 0x08>;
+			reg-names = "gpio", "pwm";
+			ngpios = <17>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			#pwm-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <87>, <88>, <89>;
+			clocks = <&coreclk 0>;
+		};
diff --git a/MAINTAINERS b/MAINTAINERS
index 40ac605..efe3a22 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -10266,6 +10266,8 @@ F:	include/linux/pwm.h
 F:	drivers/pwm/
 F:	drivers/video/backlight/pwm_bl.c
 F:	include/linux/pwm_backlight.h
+F:	drivers/gpio/gpio-mvebu.c
+F:	Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
 
 PXA2xx/PXA3xx SUPPORT
 M:	Daniel Mack <daniel@zonque.org>
diff --git a/drivers/gpio/gpio-mvebu.c b/drivers/gpio/gpio-mvebu.c
index fae4db6..ee49589 100644
--- a/drivers/gpio/gpio-mvebu.c
+++ b/drivers/gpio/gpio-mvebu.c
@@ -42,22 +42,34 @@
 #include <linux/io.h>
 #include <linux/of_irq.h>
 #include <linux/of_device.h>
+#include <linux/pwm.h>
 #include <linux/clk.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/irqchip/chained_irq.h>
+#include <linux/platform_device.h>
 #include <linux/bitops.h>
 
+#include "gpiolib.h"
+
 /*
  * GPIO unit register offsets.
  */
-#define GPIO_OUT_OFF		0x0000
-#define GPIO_IO_CONF_OFF	0x0004
-#define GPIO_BLINK_EN_OFF	0x0008
-#define GPIO_IN_POL_OFF		0x000c
-#define GPIO_DATA_IN_OFF	0x0010
-#define GPIO_EDGE_CAUSE_OFF	0x0014
-#define GPIO_EDGE_MASK_OFF	0x0018
-#define GPIO_LEVEL_MASK_OFF	0x001c
+#define GPIO_OUT_OFF			0x0000
+#define GPIO_IO_CONF_OFF		0x0004
+#define GPIO_BLINK_EN_OFF		0x0008
+#define GPIO_IN_POL_OFF			0x000c
+#define GPIO_DATA_IN_OFF		0x0010
+#define GPIO_EDGE_CAUSE_OFF		0x0014
+#define GPIO_EDGE_MASK_OFF		0x0018
+#define GPIO_LEVEL_MASK_OFF		0x001c
+#define GPIO_BLINK_CNT_SELECT_OFF	0x0020
+
+/*
+ * PWM register offsets.
+ */
+#define PWM_BLINK_ON_DURATION_OFF	0x0
+#define PWM_BLINK_OFF_DURATION_OFF	0x4
+
 
 /* The MV78200 has per-CPU registers for edge mask and level mask */
 #define GPIO_EDGE_MASK_MV78200_OFF(cpu)	  ((cpu) ? 0x30 : 0x18)
@@ -78,6 +90,21 @@
 
 #define MVEBU_MAX_GPIO_PER_BANK		32
 
+struct mvebu_pwm {
+	void __iomem		*membase;
+	unsigned long		 clk_rate;
+	bool			 used;
+	unsigned int		 pin;
+	struct pwm_chip		 chip;
+	spinlock_t		 lock;
+	struct mvebu_gpio_chip	*mvchip;
+
+	/* Used to preserve GPIO/PWM registers across suspend/resume */
+	u32			 blink_select;
+	u32			 blink_on_duration;
+	u32			 blink_off_duration;
+};
+
 struct mvebu_gpio_chip {
 	struct gpio_chip   chip;
 	spinlock_t	   lock;
@@ -87,6 +114,11 @@ struct mvebu_gpio_chip {
 	struct irq_domain *domain;
 	int		   soc_variant;
 
+	/* Used for PWM support */
+	struct clk	  *clk;
+	struct mvebu_pwm  *pwm;
+	int		   id;
+
 	/* Used to preserve GPIO registers across suspend/resume */
 	u32		   out_reg;
 	u32		   io_conf_reg;
@@ -110,6 +142,11 @@ static void __iomem *mvebu_gpioreg_blink(struct mvebu_gpio_chip *mvchip)
 	return mvchip->membase + GPIO_BLINK_EN_OFF;
 }
 
+static void __iomem *mvebu_gpioreg_blink_select(struct mvebu_gpio_chip *mvchip)
+{
+	return mvchip->membase + GPIO_BLINK_CNT_SELECT_OFF;
+}
+
 static void __iomem *mvebu_gpioreg_io_conf(struct mvebu_gpio_chip *mvchip)
 {
 	return mvchip->membase + GPIO_IO_CONF_OFF;
@@ -181,6 +218,20 @@ static void __iomem *mvebu_gpioreg_level_mask(struct mvebu_gpio_chip *mvchip)
 }
 
 /*
+ * Functions returning addresses of individual registers for a given
+ * PWM controller.
+ */
+static void __iomem *mvebu_pwmreg_blink_on_duration(struct mvebu_pwm *pwm)
+{
+	return pwm->membase + PWM_BLINK_ON_DURATION_OFF;
+}
+
+static void __iomem *mvebu_pwmreg_blink_off_duration(struct mvebu_pwm *pwm)
+{
+	return pwm->membase + PWM_BLINK_OFF_DURATION_OFF;
+}
+
+/*
  * Functions implementing the gpio_chip methods
  */
 static void mvebu_gpio_set(struct gpio_chip *chip, unsigned int pin, int value)
@@ -484,6 +535,203 @@ static void mvebu_gpio_irq_handler(struct irq_desc *desc)
 	chained_irq_exit(chip, desc);
 }
 
+/*
+ * Functions implementing the pwm_chip methods
+ */
+static struct mvebu_pwm *to_mvebu_pwm(struct pwm_chip *chip)
+{
+	return container_of(chip, struct mvebu_pwm, chip);
+}
+
+static int mvebu_pwm_request(struct pwm_chip *chip, struct pwm_device *pwmd)
+{
+	struct mvebu_pwm *pwm = to_mvebu_pwm(chip);
+	struct mvebu_gpio_chip *mvchip = pwm->mvchip;
+	struct gpio_desc *desc = gpio_to_desc(pwmd->pwm);
+	unsigned long flags;
+	int ret = 0;
+
+	spin_lock_irqsave(&pwm->lock, flags);
+	if (pwm->used) {
+		ret = -EBUSY;
+	} else {
+		if (!desc) {
+			ret = -ENODEV;
+			goto out;
+		}
+		ret = gpiod_request(desc, "mvebu-pwm");
+		if (ret)
+			goto out;
+
+		ret = gpiod_direction_output(desc, 0);
+		if (ret) {
+			gpiod_free(desc);
+			goto out;
+		}
+
+		pwm->pin = pwmd->pwm - mvchip->chip.base;
+		pwm->used = true;
+	}
+
+out:
+	spin_unlock_irqrestore(&pwm->lock, flags);
+	return ret;
+}
+
+static void mvebu_pwm_free(struct pwm_chip *chip, struct pwm_device *pwmd)
+{
+	struct mvebu_pwm *pwm = to_mvebu_pwm(chip);
+	struct gpio_desc *desc = gpio_to_desc(pwmd->pwm);
+	unsigned long flags;
+
+	spin_lock_irqsave(&pwm->lock, flags);
+	gpiod_free(desc);
+	pwm->used = false;
+	spin_unlock_irqrestore(&pwm->lock, flags);
+}
+
+static int mvebu_pwm_config(struct pwm_chip *chip, struct pwm_device *pwmd,
+			    int duty_ns, int period_ns)
+{
+	struct mvebu_pwm *pwm = to_mvebu_pwm(chip);
+	struct mvebu_gpio_chip *mvchip = pwm->mvchip;
+	unsigned int on, off;
+	unsigned long long val;
+	u32 u;
+
+	val = (unsigned long long) pwm->clk_rate * duty_ns;
+	do_div(val, NSEC_PER_SEC);
+	if (val > UINT_MAX)
+		return -EINVAL;
+	if (val)
+		on = val;
+	else
+		on = 1;
+
+	val = (unsigned long long) pwm->clk_rate * (period_ns - duty_ns);
+	do_div(val, NSEC_PER_SEC);
+	if (val > UINT_MAX)
+		return -EINVAL;
+	if (val)
+		off = val;
+	else
+		off = 1;
+
+	u = readl_relaxed(mvebu_gpioreg_blink_select(mvchip));
+	/* mvchip->id is either 0 or 1 */
+	if (mvchip->id)
+		u |= BIT(pwm->pin);
+	else
+		u &= ~BIT(pwm->pin);
+	writel_relaxed(u, mvebu_gpioreg_blink_select(mvchip));
+
+	writel_relaxed(on, mvebu_pwmreg_blink_on_duration(pwm));
+	writel_relaxed(off, mvebu_pwmreg_blink_off_duration(pwm));
+
+	return 0;
+}
+
+static int mvebu_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwmd)
+{
+	struct mvebu_pwm *pwm = to_mvebu_pwm(chip);
+	struct mvebu_gpio_chip *mvchip = pwm->mvchip;
+
+	mvebu_gpio_blink(&mvchip->chip, pwm->pin, 1);
+
+	return 0;
+}
+
+static void mvebu_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwmd)
+{
+	struct mvebu_pwm *pwm = to_mvebu_pwm(chip);
+	struct mvebu_gpio_chip *mvchip = pwm->mvchip;
+
+	mvebu_gpio_blink(&mvchip->chip, pwm->pin, 0);
+}
+
+static const struct pwm_ops mvebu_pwm_ops = {
+	.request = mvebu_pwm_request,
+	.free = mvebu_pwm_free,
+	.config = mvebu_pwm_config,
+	.enable = mvebu_pwm_enable,
+	.disable = mvebu_pwm_disable,
+	.owner = THIS_MODULE,
+};
+
+static void mvebu_pwm_suspend(struct mvebu_gpio_chip *mvchip)
+{
+	struct mvebu_pwm *pwm = mvchip->pwm;
+
+	pwm->blink_select = readl_relaxed(mvebu_gpioreg_blink_select(mvchip));
+	pwm->blink_on_duration =
+		readl_relaxed(mvebu_pwmreg_blink_on_duration(pwm));
+	pwm->blink_off_duration =
+		readl_relaxed(mvebu_pwmreg_blink_off_duration(pwm));
+}
+
+static void mvebu_pwm_resume(struct mvebu_gpio_chip *mvchip)
+{
+	struct mvebu_pwm *pwm = mvchip->pwm;
+
+	writel_relaxed(pwm->blink_select, mvebu_gpioreg_blink_select(mvchip));
+	writel_relaxed(pwm->blink_on_duration,
+		       mvebu_pwmreg_blink_on_duration(pwm));
+	writel_relaxed(pwm->blink_off_duration,
+		       mvebu_pwmreg_blink_off_duration(pwm));
+}
+
+static int mvebu_pwm_probe(struct platform_device *pdev,
+			   struct mvebu_gpio_chip *mvchip)
+{
+	struct device *dev = &pdev->dev;
+	struct mvebu_pwm *pwm;
+	struct resource *res;
+
+	/*
+	 * Armada 370/XP has simple PWM support for gpio lines. Other SoCs
+	 * don't have this hardware. So if we don't have the necessary
+	 * resource, it is not an error.
+	 */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pwm");
+	if (!res)
+		return 0;
+	/*
+	 * There are only two sets of PWM configuration registers for all
+	 * the gpio lines on those SoCs. Assert one set for each of the
+	 * first two (and only) gpio chips, return an error otherwise.
+	 */
+	if (mvchip->id < 0 || mvchip->id > 1)
+		return -EINVAL;
+
+	pwm = devm_kzalloc(dev, sizeof(struct mvebu_pwm), GFP_KERNEL);
+	if (!pwm)
+		return -ENOMEM;
+	mvchip->pwm = pwm;
+	pwm->mvchip = mvchip;
+
+	pwm->membase = devm_ioremap_resource(dev, res);
+	if (IS_ERR(pwm->membase))
+		return PTR_ERR(pwm->membase);
+
+	if (IS_ERR(mvchip->clk))
+		return PTR_ERR(mvchip->clk);
+
+	pwm->clk_rate = clk_get_rate(mvchip->clk);
+	if (!pwm->clk_rate) {
+		dev_err(dev, "failed to get clock rate\n");
+		return -EINVAL;
+	}
+
+	pwm->chip.dev = dev;
+	pwm->chip.ops = &mvebu_pwm_ops;
+	pwm->chip.base = mvchip->chip.base;
+	pwm->chip.npwm = mvchip->chip.ngpio;
+
+	spin_lock_init(&pwm->lock);
+
+	return pwmchip_add(&pwm->chip);
+}
+
 #ifdef CONFIG_DEBUG_FS
 #include <linux/seq_file.h>
 
@@ -600,6 +848,9 @@ static int mvebu_gpio_suspend(struct platform_device *pdev, pm_message_t state)
 		BUG();
 	}
 
+	if (IS_ENABLED(CONFIG_PWM))
+		mvebu_pwm_suspend(mvchip);
+
 	return 0;
 }
 
@@ -643,6 +894,9 @@ static int mvebu_gpio_resume(struct platform_device *pdev)
 		BUG();
 	}
 
+	if (IS_ENABLED(CONFIG_PWM))
+		mvebu_pwm_resume(mvchip);
+
 	return 0;
 }
 
@@ -654,11 +908,10 @@ static int mvebu_gpio_probe(struct platform_device *pdev)
 	struct resource *res;
 	struct irq_chip_generic *gc;
 	struct irq_chip_type *ct;
-	struct clk *clk;
 	unsigned int ngpios;
 	bool have_irqs;
 	int soc_variant;
-	int i, cpu, id;
+	int i, cpu;
 	int err;
 
 	match = of_match_device(mvebu_gpio_of_match, &pdev->dev);
@@ -682,16 +935,16 @@ static int mvebu_gpio_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	id = of_alias_get_id(pdev->dev.of_node, "gpio");
-	if (id < 0) {
+	mvchip->id = of_alias_get_id(pdev->dev.of_node, "gpio");
+	if (mvchip->id < 0) {
 		dev_err(&pdev->dev, "Couldn't get OF id\n");
-		return id;
+		return mvchip->id;
 	}
 
-	clk = devm_clk_get(&pdev->dev, NULL);
+	mvchip->clk = devm_clk_get(&pdev->dev, NULL);
 	/* Not all SoCs require a clock.*/
-	if (!IS_ERR(clk))
-		clk_prepare_enable(clk);
+	if (!IS_ERR(mvchip->clk))
+		clk_prepare_enable(mvchip->clk);
 
 	mvchip->soc_variant = soc_variant;
 	mvchip->chip.label = dev_name(&pdev->dev);
@@ -704,7 +957,7 @@ static int mvebu_gpio_probe(struct platform_device *pdev)
 	mvchip->chip.set = mvebu_gpio_set;
 	if (have_irqs)
 		mvchip->chip.to_irq = mvebu_gpio_to_irq;
-	mvchip->chip.base = id * MVEBU_MAX_GPIO_PER_BANK;
+	mvchip->chip.base = mvchip->id * MVEBU_MAX_GPIO_PER_BANK;
 	mvchip->chip.ngpio = ngpios;
 	mvchip->chip.can_sleep = false;
 	mvchip->chip.of_node = np;
@@ -822,6 +1075,10 @@ static int mvebu_gpio_probe(struct platform_device *pdev)
 						 mvchip);
 	}
 
+	/* Armada 370/XP has simple PWM support for gpio lines */
+	if (IS_ENABLED(CONFIG_PWM))
+		return mvebu_pwm_probe(pdev, mvchip);
+
 	return 0;
 
 err_domain:
-- 
2.10.2

Re: [PATCH v2 1/4] gpio: mvebu: Add limited PWM support

[Rob Herring]

On Sat, Mar 18, 2017 at 04:43:01PM +0100, Ralph Sennhauser wrote:
> From: Andrew Lunn <andrew@lunn.ch>
> 
> Armada 370/XP devices can 'blink' gpio lines with a configurable on
> and off period. This can be modelled as a PWM.
> 
> However, there are only two sets of PWM configuration registers for
> all the gpio lines. This driver simply allows a single gpio line per
> gpio chip of 32 lines to be used as a PWM. Attempts to use more return
> EBUSY.
> 
> Due to the interleaving of registers it is not simple to separate the
> PWM driver from the gpio driver. Thus the gpio driver has been
> extended with a PWM driver.
> 
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> URL: https://patchwork.ozlabs.org/patch/427287/
> URL: https://patchwork.ozlabs.org/patch/427295/
> [Ralph Sennhauser:
>   * port forward
>   * merge pwm portion into gpio-mvebu.c
>   * merge documentation patch
>   * update MAINTAINERS]
> Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
> ---
>  .../devicetree/bindings/gpio/gpio-mvebu.txt        |  31 +++
>  MAINTAINERS                                        |   2 +
>  drivers/gpio/gpio-mvebu.c                          | 291 +++++++++++++++++++--
>  3 files changed, 307 insertions(+), 17 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
> index a6f3bec..86932e3 100644
> --- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
> +++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
> @@ -38,6 +38,23 @@ Required properties:
>  - #gpio-cells: Should be two. The first cell is the pin number. The
>    second cell is reserved for flags, unused at the moment.
>  
> +Optional properties:
> +
> +In order to use the gpio lines in PWM mode, some additional optional
> +properties are required. Only Armada 370 and XP support these properties.
> +
> +- reg: an additional register set is needed, for the GPIO Blink
> +  Counter on/off registers.
> +
> +- reg-names: Must contain an entry "pwm" corresponding to the
> +  additional register range needed for pwm operation.
> +
> +- #pwm-cells: Should be two. The first cell is the pin number. The

s/pin number/gpio line/ ?

> +  second cell is reserved for flags and should be set to 0, so it has a
> +  known value. It then becomes possible to use it in the future.
> +
> +- clocks: Must be a phandle to the clock for the gpio controller.
> +
>  Example:
>  
>  		gpio0: gpio@d0018100 {
> @@ -51,3 +68,17 @@ Example:
>  			#interrupt-cells = <2>;
>  			interrupts = <16>, <17>, <18>, <19>;
>  		};
> +
> +		gpio1: gpio@18140 {
> +			compatible = "marvell,orion-gpio";

If only 370 and XP support this, I'd expect a compatible string for one 
of them here.

> +			reg = <0x18140 0x40>, <0x181c8 0x08>;
> +			reg-names = "gpio", "pwm";
> +			ngpios = <17>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			#pwm-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			interrupts = <87>, <88>, <89>;
> +			clocks = <&coreclk 0>;
> +		};

Re: [PATCH v2 1/4] gpio: mvebu: Add limited PWM support

[Ralph Sennhauser]

On Fri, 24 Mar 2017 10:18:29 -0500
Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:

> On Sat, Mar 18, 2017 at 04:43:01PM +0100, Ralph Sennhauser wrote:
> > From: Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>
> > 
> > Armada 370/XP devices can 'blink' gpio lines with a configurable on
> > and off period. This can be modelled as a PWM.
> > 
> > However, there are only two sets of PWM configuration registers for
> > all the gpio lines. This driver simply allows a single gpio line per
> > gpio chip of 32 lines to be used as a PWM. Attempts to use more
> > return EBUSY.
> > 
> > Due to the interleaving of registers it is not simple to separate
> > the PWM driver from the gpio driver. Thus the gpio driver has been
> > extended with a PWM driver.
> > 
> > Signed-off-by: Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>
> > URL: https://patchwork.ozlabs.org/patch/427287/
> > URL: https://patchwork.ozlabs.org/patch/427295/
> > [Ralph Sennhauser:
> >   * port forward
> >   * merge pwm portion into gpio-mvebu.c
> >   * merge documentation patch
> >   * update MAINTAINERS]
> > Signed-off-by: Ralph Sennhauser <ralph.sennhauser-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> > ---
> >  .../devicetree/bindings/gpio/gpio-mvebu.txt        |  31 +++
> >  MAINTAINERS                                        |   2 +
> >  drivers/gpio/gpio-mvebu.c                          | 291
> > +++++++++++++++++++-- 3 files changed, 307 insertions(+), 17
> > deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
> > b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt index
> > a6f3bec..86932e3 100644 ---
> > a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt +++
> > b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt @@ -38,6
> > +38,23 @@ Required properties:
> >  - #gpio-cells: Should be two. The first cell is the pin number. The
> >    second cell is reserved for flags, unused at the moment.
> >  
> > +Optional properties:
> > +
> > +In order to use the gpio lines in PWM mode, some additional
> > optional +properties are required. Only Armada 370 and XP support
> > these properties. +
> > +- reg: an additional register set is needed, for the GPIO Blink
> > +  Counter on/off registers.
> > +
> > +- reg-names: Must contain an entry "pwm" corresponding to the
> > +  additional register range needed for pwm operation.
> > +
> > +- #pwm-cells: Should be two. The first cell is the pin number.
> > The  
> 
> s/pin number/gpio line/ ?

Better indeed.

> 
> > +  second cell is reserved for flags and should be set to 0, so it
> > has a
> > +  known value. It then becomes possible to use it in the future.
> > +
> > +- clocks: Must be a phandle to the clock for the gpio controller.
> > +
> >  Example:
> >  
> >  		gpio0: gpio@d0018100 {
> > @@ -51,3 +68,17 @@ Example:
> >  			#interrupt-cells = <2>;
> >  			interrupts = <16>, <17>, <18>, <19>;
> >  		};
> > +
> > +		gpio1: gpio@18140 {
> > +			compatible = "marvell,orion-gpio";  
> 
> If only 370 and XP support this, I'd expect a compatible string for
> one of them here.

Commit 5f79c651e81e ("arm: mvebu: use global interrupts for GPIOs on
Armada XP") changes it from "marvell,armadaxp-gpio". The commit message
says for 3.8 basically leaving it open for a "fix" later.

Adding Thomas Petazzoni as the author.

Thomas, would you happen to know if this is still how it's supposed to
be for now?

Thanks
Ralph


> 
> > +			reg = <0x18140 0x40>, <0x181c8 0x08>;
> > +			reg-names = "gpio", "pwm";
> > +			ngpios = <17>;
> > +			gpio-controller;
> > +			#gpio-cells = <2>;
> > +			#pwm-cells = <2>;
> > +			interrupt-controller;
> > +			#interrupt-cells = <2>;
> > +			interrupts = <87>, <88>, <89>;
> > +			clocks = <&coreclk 0>;
> > +		};  

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 2/4] mvebu: xp: Add pwm properties to .dtsi files

[Ralph Sennhauser]

From: Andrew Lunn <andrew@lunn.ch>

Add properties to the gpio nodes to allow them to be also used as pwm
lines.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
URL: https://patchwork.ozlabs.org/patch/427294/
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
---
 arch/arm/boot/dts/armada-370.dtsi        | 10 ++++++++--
 arch/arm/boot/dts/armada-xp-mv78230.dtsi | 10 ++++++++--
 arch/arm/boot/dts/armada-xp-mv78260.dtsi |  8 ++++++--
 arch/arm/boot/dts/armada-xp-mv78460.dtsi | 10 ++++++++--
 4 files changed, 30 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi
index cc011c8..aa9fe72 100644
--- a/arch/arm/boot/dts/armada-370.dtsi
+++ b/arch/arm/boot/dts/armada-370.dtsi
@@ -138,24 +138,30 @@
 
 			gpio0: gpio@18100 {
 				compatible = "marvell,orion-gpio";
-				reg = <0x18100 0x40>;
+				reg = <0x18100 0x40>, <0x181c0 0x08>;
+				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#pwm-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				interrupts = <82>, <83>, <84>, <85>;
+				clocks = <&coreclk 0>;
 			};
 
 			gpio1: gpio@18140 {
 				compatible = "marvell,orion-gpio";
-				reg = <0x18140 0x40>;
+				reg = <0x18140 0x40>, <0x181c8 0x08>;
+				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#pwm-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				interrupts = <87>, <88>, <89>, <90>;
+				clocks = <&coreclk 0>;
 			};
 
 			gpio2: gpio@18180 {
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
index 07c5090..fc3934f 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -203,24 +203,30 @@
 		internal-regs {
 			gpio0: gpio@18100 {
 				compatible = "marvell,orion-gpio";
-				reg = <0x18100 0x40>;
+				reg = <0x18100 0x40>, <0x181c0 0x08>;
+				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#pwm-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				interrupts = <82>, <83>, <84>, <85>;
+				clocks = <&coreclk 0>;
 			};
 
 			gpio1: gpio@18140 {
 				compatible = "marvell,orion-gpio";
-				reg = <0x18140 0x40>;
+				reg = <0x18140 0x40>, <0x181c8 0x08>;
+				reg-names = "gpio", "pwm";
 				ngpios = <17>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#pwm-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				interrupts = <87>, <88>, <89>;
+				clocks = <&coreclk 0>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
index 64e936a..04dda6a 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -286,24 +286,28 @@
 		internal-regs {
 			gpio0: gpio@18100 {
 				compatible = "marvell,orion-gpio";
-				reg = <0x18100 0x40>;
+				reg = <0x18100 0x40>, <0x181c0 0x08>;
+				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#pwm-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				interrupts = <82>, <83>, <84>, <85>;
+				clocks = <&coreclk 0>;
 			};
 
 			gpio1: gpio@18140 {
 				compatible = "marvell,orion-gpio";
-				reg = <0x18140 0x40>;
+				reg = <0x18140 0x40>, <0x181c8 0x08>;
 				ngpios = <32>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				interrupts = <87>, <88>, <89>, <90>;
+				clocks = <&coreclk 0>;
 			};
 
 			gpio2: gpio@18180 {
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
index d1383dd..fb6d28a 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
@@ -324,24 +324,30 @@
 		internal-regs {
 			gpio0: gpio@18100 {
 				compatible = "marvell,orion-gpio";
-				reg = <0x18100 0x40>;
+				reg = <0x18100 0x40>, <0x181c0 0x08>;
+				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#pwm-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				interrupts = <82>, <83>, <84>, <85>;
+				clocks = <&coreclk 0>;
 			};
 
 			gpio1: gpio@18140 {
 				compatible = "marvell,orion-gpio";
-				reg = <0x18140 0x40>;
+				reg = <0x18140 0x40>, <0x181c8 0x08>;
+				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#pwm-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				interrupts = <87>, <88>, <89>, <90>;
+				clocks = <&coreclk 0>;
 			};
 
 			gpio2: gpio@18180 {
-- 
2.10.2

Re: [PATCH v2 2/4] mvebu: xp: Add pwm properties to .dtsi files

[Gregory CLEMENT]

Hi Ralph,
 
 On sam., mars 18 2017, Ralph Sennhauser <ralph.sennhauser@gmail.com> wrote:

It seems that I don't receive the 1st patch of the series.

Also could you refresh my mind to expose why these patchse were not
apply the first time and why we should apply them now?

Thanks,

Gregory


> From: Andrew Lunn <andrew@lunn.ch>
>
> Add properties to the gpio nodes to allow them to be also used as pwm
> lines.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> URL: https://patchwork.ozlabs.org/patch/427294/
> Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
> ---
>  arch/arm/boot/dts/armada-370.dtsi        | 10 ++++++++--
>  arch/arm/boot/dts/armada-xp-mv78230.dtsi | 10 ++++++++--
>  arch/arm/boot/dts/armada-xp-mv78260.dtsi |  8 ++++++--
>  arch/arm/boot/dts/armada-xp-mv78460.dtsi | 10 ++++++++--
>  4 files changed, 30 insertions(+), 8 deletions(-)
>
> diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi
> index cc011c8..aa9fe72 100644
> --- a/arch/arm/boot/dts/armada-370.dtsi
> +++ b/arch/arm/boot/dts/armada-370.dtsi
> @@ -138,24 +138,30 @@
>  
>  			gpio0: gpio@18100 {
>  				compatible = "marvell,orion-gpio";
> -				reg = <0x18100 0x40>;
> +				reg = <0x18100 0x40>, <0x181c0 0x08>;
> +				reg-names = "gpio", "pwm";
>  				ngpios = <32>;
>  				gpio-controller;
>  				#gpio-cells = <2>;
> +				#pwm-cells = <2>;
>  				interrupt-controller;
>  				#interrupt-cells = <2>;
>  				interrupts = <82>, <83>, <84>, <85>;
> +				clocks = <&coreclk 0>;
>  			};
>  
>  			gpio1: gpio@18140 {
>  				compatible = "marvell,orion-gpio";
> -				reg = <0x18140 0x40>;
> +				reg = <0x18140 0x40>, <0x181c8 0x08>;
> +				reg-names = "gpio", "pwm";
>  				ngpios = <32>;
>  				gpio-controller;
>  				#gpio-cells = <2>;
> +				#pwm-cells = <2>;
>  				interrupt-controller;
>  				#interrupt-cells = <2>;
>  				interrupts = <87>, <88>, <89>, <90>;
> +				clocks = <&coreclk 0>;
>  			};
>  
>  			gpio2: gpio@18180 {
> diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
> index 07c5090..fc3934f 100644
> --- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
> +++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
> @@ -203,24 +203,30 @@
>  		internal-regs {
>  			gpio0: gpio@18100 {
>  				compatible = "marvell,orion-gpio";
> -				reg = <0x18100 0x40>;
> +				reg = <0x18100 0x40>, <0x181c0 0x08>;
> +				reg-names = "gpio", "pwm";
>  				ngpios = <32>;
>  				gpio-controller;
>  				#gpio-cells = <2>;
> +				#pwm-cells = <2>;
>  				interrupt-controller;
>  				#interrupt-cells = <2>;
>  				interrupts = <82>, <83>, <84>, <85>;
> +				clocks = <&coreclk 0>;
>  			};
>  
>  			gpio1: gpio@18140 {
>  				compatible = "marvell,orion-gpio";
> -				reg = <0x18140 0x40>;
> +				reg = <0x18140 0x40>, <0x181c8 0x08>;
> +				reg-names = "gpio", "pwm";
>  				ngpios = <17>;
>  				gpio-controller;
>  				#gpio-cells = <2>;
> +				#pwm-cells = <2>;
>  				interrupt-controller;
>  				#interrupt-cells = <2>;
>  				interrupts = <87>, <88>, <89>;
> +				clocks = <&coreclk 0>;
>  			};
>  		};
>  	};
> diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
> index 64e936a..04dda6a 100644
> --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
> +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
> @@ -286,24 +286,28 @@
>  		internal-regs {
>  			gpio0: gpio@18100 {
>  				compatible = "marvell,orion-gpio";
> -				reg = <0x18100 0x40>;
> +				reg = <0x18100 0x40>, <0x181c0 0x08>;
> +				reg-names = "gpio", "pwm";
>  				ngpios = <32>;
>  				gpio-controller;
>  				#gpio-cells = <2>;
> +				#pwm-cells = <2>;
>  				interrupt-controller;
>  				#interrupt-cells = <2>;
>  				interrupts = <82>, <83>, <84>, <85>;
> +				clocks = <&coreclk 0>;
>  			};
>  
>  			gpio1: gpio@18140 {
>  				compatible = "marvell,orion-gpio";
> -				reg = <0x18140 0x40>;
> +				reg = <0x18140 0x40>, <0x181c8 0x08>;
>  				ngpios = <32>;
>  				gpio-controller;
>  				#gpio-cells = <2>;
>  				interrupt-controller;
>  				#interrupt-cells = <2>;
>  				interrupts = <87>, <88>, <89>, <90>;
> +				clocks = <&coreclk 0>;
>  			};
>  
>  			gpio2: gpio@18180 {
> diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
> index d1383dd..fb6d28a 100644
> --- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
> +++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
> @@ -324,24 +324,30 @@
>  		internal-regs {
>  			gpio0: gpio@18100 {
>  				compatible = "marvell,orion-gpio";
> -				reg = <0x18100 0x40>;
> +				reg = <0x18100 0x40>, <0x181c0 0x08>;
> +				reg-names = "gpio", "pwm";
>  				ngpios = <32>;
>  				gpio-controller;
>  				#gpio-cells = <2>;
> +				#pwm-cells = <2>;
>  				interrupt-controller;
>  				#interrupt-cells = <2>;
>  				interrupts = <82>, <83>, <84>, <85>;
> +				clocks = <&coreclk 0>;
>  			};
>  
>  			gpio1: gpio@18140 {
>  				compatible = "marvell,orion-gpio";
> -				reg = <0x18140 0x40>;
> +				reg = <0x18140 0x40>, <0x181c8 0x08>;
> +				reg-names = "gpio", "pwm";
>  				ngpios = <32>;
>  				gpio-controller;
>  				#gpio-cells = <2>;
> +				#pwm-cells = <2>;
>  				interrupt-controller;
>  				#interrupt-cells = <2>;
>  				interrupts = <87>, <88>, <89>, <90>;
> +				clocks = <&coreclk 0>;
>  			};
>  
>  			gpio2: gpio@18180 {
> -- 
> 2.10.2
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

Re: [PATCH v2 2/4] mvebu: xp: Add pwm properties to .dtsi files

[Andrew Lunn]

> Also could you refresh my mind to expose why these patchse were not
> apply the first time and why we should apply them now?

Hi Gregory

Because i got busy with other things, and never spent the time needed
to address the comments. Ralph has addressed all the comments from the
original posting.

	 Andrew

Re: [PATCH v2 2/4] mvebu: xp: Add pwm properties to .dtsi files

[Ralph Sennhauser]

On Thu, 23 Mar 2017 17:40:53 +0100
Gregory CLEMENT <gregory.clement@free-electrons.com> wrote:

> Hi Ralph,
>  
>  On sam., mars 18 2017, Ralph Sennhauser <ralph.sennhauser@gmail.com>
> wrote:
> 
> It seems that I don't receive the 1st patch of the series.

Hi Gregory,

it makes no sense to only send part of a series to a recipient. Will
have to improve my use of --cc-cmd it seems. Will pay attention to this
for v3.

Sorry
Ralph

> 
> Also could you refresh my mind to expose why these patchse were not
> apply the first time and why we should apply them now?
> 
> Thanks,
> 
> Gregory
> 
> 
> > From: Andrew Lunn <andrew@lunn.ch>
> >
> > Add properties to the gpio nodes to allow them to be also used as
> > pwm lines.
> >
> > Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> > URL: https://patchwork.ozlabs.org/patch/427294/
> > Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
> > ---
> >  arch/arm/boot/dts/armada-370.dtsi        | 10 ++++++++--
> >  arch/arm/boot/dts/armada-xp-mv78230.dtsi | 10 ++++++++--
> >  arch/arm/boot/dts/armada-xp-mv78260.dtsi |  8 ++++++--
> >  arch/arm/boot/dts/armada-xp-mv78460.dtsi | 10 ++++++++--
> >  4 files changed, 30 insertions(+), 8 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/armada-370.dtsi
> > b/arch/arm/boot/dts/armada-370.dtsi index cc011c8..aa9fe72 100644
> > --- a/arch/arm/boot/dts/armada-370.dtsi
> > +++ b/arch/arm/boot/dts/armada-370.dtsi
> > @@ -138,24 +138,30 @@
> >  
> >  			gpio0: gpio@18100 {
> >  				compatible = "marvell,orion-gpio";
> > -				reg = <0x18100 0x40>;
> > +				reg = <0x18100 0x40>, <0x181c0
> > 0x08>;
> > +				reg-names = "gpio", "pwm";
> >  				ngpios = <32>;
> >  				gpio-controller;
> >  				#gpio-cells = <2>;
> > +				#pwm-cells = <2>;
> >  				interrupt-controller;
> >  				#interrupt-cells = <2>;
> >  				interrupts = <82>, <83>, <84>,
> > <85>;
> > +				clocks = <&coreclk 0>;
> >  			};
> >  
> >  			gpio1: gpio@18140 {
> >  				compatible = "marvell,orion-gpio";
> > -				reg = <0x18140 0x40>;
> > +				reg = <0x18140 0x40>, <0x181c8
> > 0x08>;
> > +				reg-names = "gpio", "pwm";
> >  				ngpios = <32>;
> >  				gpio-controller;
> >  				#gpio-cells = <2>;
> > +				#pwm-cells = <2>;
> >  				interrupt-controller;
> >  				#interrupt-cells = <2>;
> >  				interrupts = <87>, <88>, <89>,
> > <90>;
> > +				clocks = <&coreclk 0>;
> >  			};
> >  
> >  			gpio2: gpio@18180 {
> > diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
> > b/arch/arm/boot/dts/armada-xp-mv78230.dtsi index 07c5090..fc3934f
> > 100644 --- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
> > +++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
> > @@ -203,24 +203,30 @@
> >  		internal-regs {
> >  			gpio0: gpio@18100 {
> >  				compatible = "marvell,orion-gpio";
> > -				reg = <0x18100 0x40>;
> > +				reg = <0x18100 0x40>, <0x181c0
> > 0x08>;
> > +				reg-names = "gpio", "pwm";
> >  				ngpios = <32>;
> >  				gpio-controller;
> >  				#gpio-cells = <2>;
> > +				#pwm-cells = <2>;
> >  				interrupt-controller;
> >  				#interrupt-cells = <2>;
> >  				interrupts = <82>, <83>, <84>,
> > <85>;
> > +				clocks = <&coreclk 0>;
> >  			};
> >  
> >  			gpio1: gpio@18140 {
> >  				compatible = "marvell,orion-gpio";
> > -				reg = <0x18140 0x40>;
> > +				reg = <0x18140 0x40>, <0x181c8
> > 0x08>;
> > +				reg-names = "gpio", "pwm";
> >  				ngpios = <17>;
> >  				gpio-controller;
> >  				#gpio-cells = <2>;
> > +				#pwm-cells = <2>;
> >  				interrupt-controller;
> >  				#interrupt-cells = <2>;
> >  				interrupts = <87>, <88>, <89>;
> > +				clocks = <&coreclk 0>;
> >  			};
> >  		};
> >  	};
> > diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
> > b/arch/arm/boot/dts/armada-xp-mv78260.dtsi index 64e936a..04dda6a
> > 100644 --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
> > +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
> > @@ -286,24 +286,28 @@
> >  		internal-regs {
> >  			gpio0: gpio@18100 {
> >  				compatible = "marvell,orion-gpio";
> > -				reg = <0x18100 0x40>;
> > +				reg = <0x18100 0x40>, <0x181c0
> > 0x08>;
> > +				reg-names = "gpio", "pwm";
> >  				ngpios = <32>;
> >  				gpio-controller;
> >  				#gpio-cells = <2>;
> > +				#pwm-cells = <2>;
> >  				interrupt-controller;
> >  				#interrupt-cells = <2>;
> >  				interrupts = <82>, <83>, <84>,
> > <85>;
> > +				clocks = <&coreclk 0>;
> >  			};
> >  
> >  			gpio1: gpio@18140 {
> >  				compatible = "marvell,orion-gpio";
> > -				reg = <0x18140 0x40>;
> > +				reg = <0x18140 0x40>, <0x181c8
> > 0x08>; ngpios = <32>;
> >  				gpio-controller;
> >  				#gpio-cells = <2>;
> >  				interrupt-controller;
> >  				#interrupt-cells = <2>;
> >  				interrupts = <87>, <88>, <89>,
> > <90>;
> > +				clocks = <&coreclk 0>;
> >  			};
> >  
> >  			gpio2: gpio@18180 {
> > diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
> > b/arch/arm/boot/dts/armada-xp-mv78460.dtsi index d1383dd..fb6d28a
> > 100644 --- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
> > +++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
> > @@ -324,24 +324,30 @@
> >  		internal-regs {
> >  			gpio0: gpio@18100 {
> >  				compatible = "marvell,orion-gpio";
> > -				reg = <0x18100 0x40>;
> > +				reg = <0x18100 0x40>, <0x181c0
> > 0x08>;
> > +				reg-names = "gpio", "pwm";
> >  				ngpios = <32>;
> >  				gpio-controller;
> >  				#gpio-cells = <2>;
> > +				#pwm-cells = <2>;
> >  				interrupt-controller;
> >  				#interrupt-cells = <2>;
> >  				interrupts = <82>, <83>, <84>,
> > <85>;
> > +				clocks = <&coreclk 0>;
> >  			};
> >  
> >  			gpio1: gpio@18140 {
> >  				compatible = "marvell,orion-gpio";
> > -				reg = <0x18140 0x40>;
> > +				reg = <0x18140 0x40>, <0x181c8
> > 0x08>;
> > +				reg-names = "gpio", "pwm";
> >  				ngpios = <32>;
> >  				gpio-controller;
> >  				#gpio-cells = <2>;
> > +				#pwm-cells = <2>;
> >  				interrupt-controller;
> >  				#interrupt-cells = <2>;
> >  				interrupts = <87>, <88>, <89>,
> > <90>;
> > +				clocks = <&coreclk 0>;
> >  			};
> >  
> >  			gpio2: gpio@18180 {
> > -- 
> > 2.10.2
> >  
> 

[PATCH v2 4/4] mvebu: wrt1900ac: Use pwm-fan rather than gpio-fan

[Ralph Sennhauser]

From: Andrew Lunn <andrew@lunn.ch>

The mvebu gpio driver can also perform PWM on some pins. Us the pwm-fan
driver to control the fan of the WRT1900AC, giving us finer grained
control over its speed and hence noise.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
URL: https://patchwork.ozlabs.org/patch/427291/
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
---
 arch/arm/boot/dts/armada-xp-linksys-mamba.dts | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
index 3744ba3..836b275e 100644
--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
@@ -293,13 +293,11 @@
 		};
 	};
 
-	gpio_fan {
+	pwm_fan {
 		/* SUNON HA4010V4-0000-C99 */
-		compatible = "gpio-fan";
-		gpios = <&gpio0 24 0>;
 
-		gpio-fan,speed-map = <0    0
-				      4500 1>;
+		compatible = "pwm-fan";
+		pwms = <&gpio0 24 4000 0>;
 	};
 
 	dsa {
-- 
2.10.2