* [PATCH linux v5 0/2] Support for ASPEED AST2400/AST2500 PWM and Fan Tach driver
@ 2017-03-24 18:17 Jaghathiswari Rankappagounder Natarajan
[not found] ` <20170324181723.29379-1-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>
2017-03-24 18:17 ` [PATCH linux v5 2/2] drivers: hwmon: Support for ASPEED PWM/Fan tach Jaghathiswari Rankappagounder Natarajan
0 siblings, 2 replies; 7+ messages in thread
From: Jaghathiswari Rankappagounder Natarajan @ 2017-03-24 18:17 UTC (permalink / raw)
To: joel, jdelvare, linux, linux-hwmon, linux-kernel, openbmc, corbet,
linux-doc, robh+dt, mark.rutland, devicetree
Cc: Jaghathiswari Rankappagounder Natarajan
Support for ASPEED AST2400/AST2500 PWM and Fan Tach driver.
Patches based on the upstream tag 4.9. Changes made in Version 4 are indicated
in the individual patches.
The AST2400/AST2500 PWM controller can support 8 PWM output ports.
The AST2400/AST2500 Fan Tach controller can support 16 tachometer inputs.
The hwmon driver provides sysfs entries through which the user can configure the
duty cycle for the particular PWM output port and read the fan rpm value for
the particular tachometer input.
Added devicetree binding documentation for AST2400/AST2500 PWM and Fan Tach
support.
Tested on Zaius board (which has AST2500 chip) and observed that when
duty cycle is lowered then the fan speed is lowered and lower fan rpm value(
corresponding to the duty cycle) is reported and when the duty cycle is
increased then the fan speed increases and higher fan rpm value(corresponding
to the duty cycle) is reported.
Jaghathiswari Rankappagounder Natarajan (2):
Documentation: dt-bindings: Document bindings for ASPEED
AST2400/AST2500 PWM and Fan tach controller device driver
drivers: hwmon: Support for ASPEED PWM/Fan tach
.../devicetree/bindings/hwmon/aspeed-pwm-tacho.txt | 68 ++
Documentation/hwmon/aspeed-pwm-tacho | 22 +
drivers/hwmon/Kconfig | 13 +-
drivers/hwmon/Makefile | 1 +
drivers/hwmon/aspeed-pwm-tacho.c | 854 +++++++++++++++++++++
5 files changed, 956 insertions(+), 2 deletions(-)
create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt
create mode 100644 Documentation/hwmon/aspeed-pwm-tacho
create mode 100644 drivers/hwmon/aspeed-pwm-tacho.c
--
2.12.1.578.ge9c3154ca4-goog
^ permalink raw reply [flat|nested] 7+ messages in thread[parent not found: <20170324181723.29379-1-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>]
* [PATCH linux v5 1/2] Documentation: dt-bindings: Document bindings for ASPEED AST2400/AST2500 PWM and Fan tach controller device driver [not found] ` <20170324181723.29379-1-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org> @ 2017-03-24 18:17 ` Jaghathiswari Rankappagounder Natarajan 2017-03-29 22:14 ` Jaghathiswari Rankappagounder Natarajan 2017-03-30 22:46 ` Rob Herring 0 siblings, 2 replies; 7+ messages in thread From: Jaghathiswari Rankappagounder Natarajan @ 2017-03-24 18:17 UTC (permalink / raw) To: joel-U3u1mxZcP9KHXe+LvDLADg, jdelvare-IBi9RG/b67k, linux-0h96xk9xTtrk1uMJSBkQmQ, linux-hwmon-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, openbmc-uLR06cmDAlY/bJ5BZ2RsiQ, corbet-T1hC0tSOHrs, linux-doc-u79uwXL29TY76Z2rM5mHXA, robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, devicetree-u79uwXL29TY76Z2rM5mHXA Cc: Jaghathiswari Rankappagounder Natarajan This binding provides interface for adding values related to ASPEED AST2400/2500 PWM and Fan tach controller support. The PWM controller can support upto 8 PWM output ports. The Fan tach controller can support upto 16 tachometer inputs. Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org> --- v5: - Changed the naming scheme to aspeed,ast2400/2500-pwm-tacho - Removed gpio pin muxing - Added aspeed vendor prefix for fan-tach-ch - Changed to fan@0/1 - Changed reg to 32 bits v4: - Used 'reg' v3: - Made the structure more common v2: - Removed '_' in node and property names - Gave some explanation for the properties used .../devicetree/bindings/hwmon/aspeed-pwm-tacho.txt | 68 ++++++++++++++++++++++ 1 file changed, 68 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt diff --git a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt new file mode 100644 index 000000000000..f96d32bfcdfa --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt @@ -0,0 +1,68 @@ +ASPEED AST2400/AST2500 PWM and Fan Tacho controller device driver + +The ASPEED PWM controller can support upto 8 PWM outputs. The ASPEED Fan Tacho +controller can support upto 16 Fan tachometer inputs. + +There can be upto 8 fans supported. Each fan can have one PWM output and +one/two Fan tach inputs. + +Required properties for pwm-tacho node: +- #address-cells : should be 1. + +- #size-cells : should be 1. + +- reg : address and length of the register set for the device. + +- pinctrl-names : a pinctrl state named "default" must be defined. + +- pinctrl-0 : phandle referencing pin configuration of the PWM ports. + +- compatible : should be "aspeed,ast2400-pwm-tacho" for AST2400 and + "aspeed,ast2500-pwm-tacho" for AST2500. + +- clocks : a fixed clock providing input clock frequency(PWM + and Fan Tach clock) + +fan subnode format: +=================== +Under fan subnode there can upto 8 child nodes, with each child node +representing a fan. If there are 8 fans each fan can have one PWM port and +one/two Fan tach inputs. + +Required properties for each child node: +- reg : should specify PWM source port. + integer value in the range 0 to 7 with 0 indicating PWM port A and + 7 indicating PWM port H. + +- aspeed-fan-tach-ch : should specify the Fan tach input channel. + integer value in the range 0 through 15, with 0 indicating + Fan tach channel 0 and 15 indicating Fan tach channel 15. + Atleast one Fan tach input channel is required. + +Examples: + +pwm_tacho_fixed_clk: fixedclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; +} + +pwm_tacho: pwmtachocontroller@1e786000 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0x1E786000 0x1000>; + compatible = "aspeed,ast2500-pwm-tacho"; + clocks = <&pwm_tacho_fixed_clk>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>; + + fan@0 { + reg = <0x00>; + aspeed-fan-tach-ch = /bits/ 8 <0x00>; + }; + + fan@1 { + reg = <0x01>; + aspeed-fan-tach-ch = /bits/ 8 <0x01 0x02>; + }; +}; -- 2.12.1.578.ge9c3154ca4-goog -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH linux v5 1/2] Documentation: dt-bindings: Document bindings for ASPEED AST2400/AST2500 PWM and Fan tach controller device driver 2017-03-24 18:17 ` [PATCH linux v5 1/2] Documentation: dt-bindings: Document bindings for ASPEED AST2400/AST2500 PWM and Fan tach controller device driver Jaghathiswari Rankappagounder Natarajan @ 2017-03-29 22:14 ` Jaghathiswari Rankappagounder Natarajan 2017-03-30 22:46 ` Rob Herring 1 sibling, 0 replies; 7+ messages in thread From: Jaghathiswari Rankappagounder Natarajan @ 2017-03-29 22:14 UTC (permalink / raw) To: Joel Stanley, jdelvare, Guenter Roeck, linux-hwmon, linux-kernel, OpenBMC Maillist, Jonathan Corbet, linux-doc, robh+dt, mark.rutland, devicetree Cc: Jaghathiswari Rankappagounder Natarajan Please provide review comments. On Fri, Mar 24, 2017 at 11:17 AM, Jaghathiswari Rankappagounder Natarajan <jaghu@google.com> wrote: > This binding provides interface for adding values related to ASPEED > AST2400/2500 PWM and Fan tach controller support. > The PWM controller can support upto 8 PWM output ports. > The Fan tach controller can support upto 16 tachometer inputs. > > Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com> > --- > v5: > - Changed the naming scheme to aspeed,ast2400/2500-pwm-tacho > - Removed gpio pin muxing > - Added aspeed vendor prefix for fan-tach-ch > - Changed to fan@0/1 > - Changed reg to 32 bits > > v4: > - Used 'reg' > > v3: > - Made the structure more common > > v2: > - Removed '_' in node and property names > - Gave some explanation for the properties used > > .../devicetree/bindings/hwmon/aspeed-pwm-tacho.txt | 68 ++++++++++++++++++++++ > 1 file changed, 68 insertions(+) > create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > > diff --git a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > new file mode 100644 > index 000000000000..f96d32bfcdfa > --- /dev/null > +++ b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > @@ -0,0 +1,68 @@ > +ASPEED AST2400/AST2500 PWM and Fan Tacho controller device driver > + > +The ASPEED PWM controller can support upto 8 PWM outputs. The ASPEED Fan Tacho > +controller can support upto 16 Fan tachometer inputs. > + > +There can be upto 8 fans supported. Each fan can have one PWM output and > +one/two Fan tach inputs. > + > +Required properties for pwm-tacho node: > +- #address-cells : should be 1. > + > +- #size-cells : should be 1. > + > +- reg : address and length of the register set for the device. > + > +- pinctrl-names : a pinctrl state named "default" must be defined. > + > +- pinctrl-0 : phandle referencing pin configuration of the PWM ports. > + > +- compatible : should be "aspeed,ast2400-pwm-tacho" for AST2400 and > + "aspeed,ast2500-pwm-tacho" for AST2500. > + > +- clocks : a fixed clock providing input clock frequency(PWM > + and Fan Tach clock) > + > +fan subnode format: > +=================== > +Under fan subnode there can upto 8 child nodes, with each child node > +representing a fan. If there are 8 fans each fan can have one PWM port and > +one/two Fan tach inputs. > + > +Required properties for each child node: > +- reg : should specify PWM source port. > + integer value in the range 0 to 7 with 0 indicating PWM port A and > + 7 indicating PWM port H. > + > +- aspeed-fan-tach-ch : should specify the Fan tach input channel. > + integer value in the range 0 through 15, with 0 indicating > + Fan tach channel 0 and 15 indicating Fan tach channel 15. > + Atleast one Fan tach input channel is required. > + > +Examples: > + > +pwm_tacho_fixed_clk: fixedclk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <24000000>; > +} > + > +pwm_tacho: pwmtachocontroller@1e786000 { > + #address-cells = <1>; > + #size-cells = <1>; > + reg = <0x1E786000 0x1000>; > + compatible = "aspeed,ast2500-pwm-tacho"; > + clocks = <&pwm_tacho_fixed_clk>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>; > + > + fan@0 { > + reg = <0x00>; > + aspeed-fan-tach-ch = /bits/ 8 <0x00>; > + }; > + > + fan@1 { > + reg = <0x01>; > + aspeed-fan-tach-ch = /bits/ 8 <0x01 0x02>; > + }; > +}; > -- > 2.12.1.578.ge9c3154ca4-goog > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH linux v5 1/2] Documentation: dt-bindings: Document bindings for ASPEED AST2400/AST2500 PWM and Fan tach controller device driver 2017-03-24 18:17 ` [PATCH linux v5 1/2] Documentation: dt-bindings: Document bindings for ASPEED AST2400/AST2500 PWM and Fan tach controller device driver Jaghathiswari Rankappagounder Natarajan 2017-03-29 22:14 ` Jaghathiswari Rankappagounder Natarajan @ 2017-03-30 22:46 ` Rob Herring 1 sibling, 0 replies; 7+ messages in thread From: Rob Herring @ 2017-03-30 22:46 UTC (permalink / raw) To: Jaghathiswari Rankappagounder Natarajan Cc: joel, jdelvare, linux, linux-hwmon, linux-kernel, openbmc, corbet, linux-doc, mark.rutland, devicetree On Fri, Mar 24, 2017 at 11:17:22AM -0700, Jaghathiswari Rankappagounder Natarajan wrote: > This binding provides interface for adding values related to ASPEED > AST2400/2500 PWM and Fan tach controller support. > The PWM controller can support upto 8 PWM output ports. > The Fan tach controller can support upto 16 tachometer inputs. > > Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com> > --- > v5: > - Changed the naming scheme to aspeed,ast2400/2500-pwm-tacho > - Removed gpio pin muxing > - Added aspeed vendor prefix for fan-tach-ch > - Changed to fan@0/1 > - Changed reg to 32 bits > > v4: > - Used 'reg' > > v3: > - Made the structure more common > > v2: > - Removed '_' in node and property names > - Gave some explanation for the properties used > > .../devicetree/bindings/hwmon/aspeed-pwm-tacho.txt | 68 ++++++++++++++++++++++ > 1 file changed, 68 insertions(+) > create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > > diff --git a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > new file mode 100644 > index 000000000000..f96d32bfcdfa > --- /dev/null > +++ b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > @@ -0,0 +1,68 @@ > +ASPEED AST2400/AST2500 PWM and Fan Tacho controller device driver > + > +The ASPEED PWM controller can support upto 8 PWM outputs. The ASPEED Fan Tacho > +controller can support upto 16 Fan tachometer inputs. > + > +There can be upto 8 fans supported. Each fan can have one PWM output and > +one/two Fan tach inputs. > + > +Required properties for pwm-tacho node: > +- #address-cells : should be 1. > + > +- #size-cells : should be 1. > + > +- reg : address and length of the register set for the device. > + > +- pinctrl-names : a pinctrl state named "default" must be defined. > + > +- pinctrl-0 : phandle referencing pin configuration of the PWM ports. > + > +- compatible : should be "aspeed,ast2400-pwm-tacho" for AST2400 and > + "aspeed,ast2500-pwm-tacho" for AST2500. > + > +- clocks : a fixed clock providing input clock frequency(PWM > + and Fan Tach clock) > + > +fan subnode format: > +=================== > +Under fan subnode there can upto 8 child nodes, with each child node > +representing a fan. If there are 8 fans each fan can have one PWM port and > +one/two Fan tach inputs. > + > +Required properties for each child node: > +- reg : should specify PWM source port. > + integer value in the range 0 to 7 with 0 indicating PWM port A and > + 7 indicating PWM port H. > + > +- aspeed-fan-tach-ch : should specify the Fan tach input channel. aspeed,fan-tach-ch With that, Acked-by: Rob Herring <robh@kernel.org> > + integer value in the range 0 through 15, with 0 indicating > + Fan tach channel 0 and 15 indicating Fan tach channel 15. > + Atleast one Fan tach input channel is required. > + > +Examples: > + > +pwm_tacho_fixed_clk: fixedclk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <24000000>; > +} > + > +pwm_tacho: pwmtachocontroller@1e786000 { > + #address-cells = <1>; > + #size-cells = <1>; > + reg = <0x1E786000 0x1000>; > + compatible = "aspeed,ast2500-pwm-tacho"; > + clocks = <&pwm_tacho_fixed_clk>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>; > + > + fan@0 { > + reg = <0x00>; > + aspeed-fan-tach-ch = /bits/ 8 <0x00>; > + }; > + > + fan@1 { > + reg = <0x01>; > + aspeed-fan-tach-ch = /bits/ 8 <0x01 0x02>; > + }; > +}; > -- > 2.12.1.578.ge9c3154ca4-goog > ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH linux v5 2/2] drivers: hwmon: Support for ASPEED PWM/Fan tach 2017-03-24 18:17 [PATCH linux v5 0/2] Support for ASPEED AST2400/AST2500 PWM and Fan Tach driver Jaghathiswari Rankappagounder Natarajan [not found] ` <20170324181723.29379-1-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org> @ 2017-03-24 18:17 ` Jaghathiswari Rankappagounder Natarajan 2017-03-29 22:15 ` Jaghathiswari Rankappagounder Natarajan [not found] ` <20170324181723.29379-3-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org> 1 sibling, 2 replies; 7+ messages in thread From: Jaghathiswari Rankappagounder Natarajan @ 2017-03-24 18:17 UTC (permalink / raw) To: joel, jdelvare, linux, linux-hwmon, linux-kernel, openbmc, corbet, linux-doc, robh+dt, mark.rutland, devicetree Cc: Jaghathiswari Rankappagounder Natarajan The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports. The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer inputs. The device driver matches on the device tree node. The configuration values are read from the device tree and written to the respective registers. The driver provides a sysfs entries through which the user can configure the duty-cycle value (ranging from 0 to 100 percent) and read the fan tach rpm value. Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com> --- v5: - Changed the driver to suit the changes in the device tree documentation v4: - Modified this driver to suit the representation in the devicetree v3: - Only sent out device tree documentation; did not send this driver v2: - Used BIT() - Used regmap - Avoided division when raw data is 0 - Removed empty lines between declaration - Removed macros; Used two attribute groups and used is_visible callback - Returned error when properties are undefined - Removed .owner field - Used PTR_ERR_OR_ZERO - Removed explicit of_node_put for child nodes Documentation/hwmon/aspeed-pwm-tacho | 22 + drivers/hwmon/Kconfig | 13 +- drivers/hwmon/Makefile | 1 + drivers/hwmon/aspeed-pwm-tacho.c | 854 +++++++++++++++++++++++++++++++++++ 4 files changed, 888 insertions(+), 2 deletions(-) create mode 100644 Documentation/hwmon/aspeed-pwm-tacho create mode 100644 drivers/hwmon/aspeed-pwm-tacho.c diff --git a/Documentation/hwmon/aspeed-pwm-tacho b/Documentation/hwmon/aspeed-pwm-tacho new file mode 100644 index 000000000000..0e9ec6d5f900 --- /dev/null +++ b/Documentation/hwmon/aspeed-pwm-tacho @@ -0,0 +1,22 @@ +Kernel driver aspeed-pwm-tacho +============================== + +Supported chips: + ASPEED AST2400/2500 + +Authors: + <jaghu@google.com> + +Description: +------------ +This driver implements support for ASPEED AST2400/2500 PWM and Fan Tacho +controller. The PWM controller supports upto 8 PWM outputs. The Fan tacho +controller supports upto 16 tachometer inputs. + +The driver provides the following sensor accesses in sysfs: + +fanX_input ro provide current fan rotation value in RPM as reported + by the fan to the device. + +pwmX rw get or set PWM fan control value. This is an integer + value between 0(off) and 255(full speed). diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 45cef3d2c75c..487110f21827 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -341,6 +341,15 @@ config SENSORS_ASB100 This driver can also be built as a module. If so, the module will be called asb100. +config SENSORS_ASPEED + tristate "ASPEED AST2400/AST2500 PWM and Fan tach driver" + help + This driver provides support for ASPEED AST2400/AST2500 PWM + and Fan Tacho controllers. + + This driver can also be built as a module. If so, the module + will be called aspeed_pwm_tacho. + config SENSORS_ATXP1 tristate "Attansic ATXP1 VID controller" depends on I2C @@ -952,7 +961,7 @@ config SENSORS_LM70 help If you say yes here you get support for the National Semiconductor LM70, LM71, LM74 and Texas Instruments TMP121/TMP123 digital tempera- - ture sensor chips. + true sensor chips. This driver can also be built as a module. If so, the module will be called lm70. @@ -1506,7 +1515,7 @@ config SENSORS_ADS7871 config SENSORS_AMC6821 tristate "Texas Instruments AMC6821" - depends on I2C + depends on I2C help If you say yes here you get support for the Texas Instruments AMC6821 hardware monitoring chips. diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index aecf4ba17460..83025cc9bb45 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -46,6 +46,7 @@ obj-$(CONFIG_SENSORS_ADT7475) += adt7475.o obj-$(CONFIG_SENSORS_APPLESMC) += applesmc.o obj-$(CONFIG_SENSORS_ARM_SCPI) += scpi-hwmon.o obj-$(CONFIG_SENSORS_ASC7621) += asc7621.o +obj-$(CONFIG_SENSORS_ASPEED) += aspeed-pwm-tacho.o obj-$(CONFIG_SENSORS_ATXP1) += atxp1.o obj-$(CONFIG_SENSORS_CORETEMP) += coretemp.o obj-$(CONFIG_SENSORS_DA9052_ADC)+= da9052-hwmon.o diff --git a/drivers/hwmon/aspeed-pwm-tacho.c b/drivers/hwmon/aspeed-pwm-tacho.c new file mode 100644 index 000000000000..28888cc34555 --- /dev/null +++ b/drivers/hwmon/aspeed-pwm-tacho.c @@ -0,0 +1,854 @@ +/* + * Copyright (c) 2016 Google, Inc + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 or later as + * published by the Free Software Foundation. + */ + +#include <linux/clk.h> +#include <linux/gpio/consumer.h> +#include <linux/delay.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of_platform.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/sysfs.h> +#include <linux/regmap.h> + +/* ASPEED PWM & FAN Tach Register Definition */ +#define ASPEED_PTCR_CTRL 0x00 +#define ASPEED_PTCR_CLK_CTRL 0x04 +#define ASPEED_PTCR_DUTY0_CTRL 0x08 +#define ASPEED_PTCR_DUTY1_CTRL 0x0c +#define ASPEED_PTCR_TYPEM_CTRL 0x10 +#define ASPEED_PTCR_TYPEM_CTRL1 0x14 +#define ASPEED_PTCR_TYPEN_CTRL 0x18 +#define ASPEED_PTCR_TYPEN_CTRL1 0x1c +#define ASPEED_PTCR_TACH_SOURCE 0x20 +#define ASPEED_PTCR_TRIGGER 0x28 +#define ASPEED_PTCR_RESULT 0x2c +#define ASPEED_PTCR_INTR_CTRL 0x30 +#define ASPEED_PTCR_INTR_STS 0x34 +#define ASPEED_PTCR_TYPEM_LIMIT 0x38 +#define ASPEED_PTCR_TYPEN_LIMIT 0x3C +#define ASPEED_PTCR_CTRL_EXT 0x40 +#define ASPEED_PTCR_CLK_CTRL_EXT 0x44 +#define ASPEED_PTCR_DUTY2_CTRL 0x48 +#define ASPEED_PTCR_DUTY3_CTRL 0x4c +#define ASPEED_PTCR_TYPEO_CTRL 0x50 +#define ASPEED_PTCR_TYPEO_CTRL1 0x54 +#define ASPEED_PTCR_TACH_SOURCE_EXT 0x60 +#define ASPEED_PTCR_TYPEO_LIMIT 0x78 + +/* ASPEED_PTCR_CTRL : 0x00 - General Control Register */ +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART1 15 +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART2 6 +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_MASK (BIT(7) | BIT(15)) + +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART1 14 +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART2 5 +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_MASK (BIT(6) | BIT(14)) + +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART1 13 +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART2 4 +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_MASK (BIT(5) | BIT(13)) + +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART1 12 +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART2 3 +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_MASK (BIT(4) | BIT(12)) + +#define ASPEED_PTCR_CTRL_FAN_NUM_EN(x) BIT(16 + (x)) + +#define ASPEED_PTCR_CTRL_PWMD_EN BIT(11) +#define ASPEED_PTCR_CTRL_PWMC_EN BIT(10) +#define ASPEED_PTCR_CTRL_PWMB_EN BIT(9) +#define ASPEED_PTCR_CTRL_PWMA_EN BIT(8) + +#define ASPEED_PTCR_CTRL_CLK_SRC BIT(1) +#define ASPEED_PTCR_CTRL_CLK_EN BIT(0) + +/* ASPEED_PTCR_CLK_CTRL : 0x04 - Clock Control Register */ +/* TYPE N */ +#define ASPEED_PTCR_CLK_CTRL_TYPEN_MASK GENMASK(31, 16) +#define ASPEED_PTCR_CLK_CTRL_TYPEN_UNIT 24 +#define ASPEED_PTCR_CLK_CTRL_TYPEN_H 20 +#define ASPEED_PTCR_CLK_CTRL_TYPEN_L 16 +/* TYPE M */ +#define ASPEED_PTCR_CLK_CTRL_TYPEM_MASK GENMASK(15, 0) +#define ASPEED_PTCR_CLK_CTRL_TYPEM_UNIT 8 +#define ASPEED_PTCR_CLK_CTRL_TYPEM_H 4 +#define ASPEED_PTCR_CLK_CTRL_TYPEM_L 0 + +/* + * ASPEED_PTCR_DUTY_CTRL/1/2/3 : 0x08/0x0C/0x48/0x4C - PWM-FAN duty control + * 0/1/2/3 register + */ +#define DUTY_CTRL_PWM2_FALL_POINT 24 +#define DUTY_CTRL_PWM2_RISE_POINT 16 +#define DUTY_CTRL_PWM2_RISE_FALL_MASK GENMASK(31, 16) +#define DUTY_CTRL_PWM1_FALL_POINT 8 +#define DUTY_CTRL_PWM1_RISE_POINT 0 +#define DUTY_CTRL_PWM1_RISE_FALL_MASK GENMASK(15, 0) + +/* ASPEED_PTCR_TYPEM_CTRL : 0x10/0x18/0x50 - Type M/N/O Ctrl 0 Register */ +#define TYPE_CTRL_FAN_MASK (GENMASK(5, 1) | GENMASK(31, 16)) +#define TYPE_CTRL_FAN1_MASK GENMASK(31, 0) +#define TYPE_CTRL_FAN_PERIOD 16 +#define TYPE_CTRL_FAN_MODE 4 +#define TYPE_CTRL_FAN_DIVISION 1 +#define TYPE_CTRL_FAN_TYPE_EN 1 + +/* ASPEED_PTCR_TACH_SOURCE : 0x20/0x60 - Tach Source Register */ +/* bit [0,1] at 0x20, bit [2] at 0x60 */ +#define TACH_PWM_SOURCE_BIT01(x) ((x) * 2) +#define TACH_PWM_SOURCE_BIT2(x) ((x) * 2) +#define TACH_PWM_SOURCE_MASK_BIT01(x) (0x3 << ((x) * 2)) +#define TACH_PWM_SOURCE_MASK_BIT2(x) BIT((x) * 2) + +/* ASPEED_PTCR_RESULT : 0x2c - Result Register */ +#define RESULT_STATUS_MASK BIT(31) +#define RESULT_VALUE_MASK 0xfffff + +/* ASPEED_PTCR_CTRL_EXT : 0x40 - General Control Extension #1 Register */ +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART1 15 +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART2 6 +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_MASK (BIT(7) | BIT(15)) + +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART1 14 +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART2 5 +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_MASK (BIT(6) | BIT(14)) + +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART1 13 +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART2 4 +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_MASK (BIT(5) | BIT(13)) + +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART1 12 +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART2 3 +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_MASK (BIT(4) | BIT(12)) + +#define ASPEED_PTCR_CTRL_PWMH_EN BIT(11) +#define ASPEED_PTCR_CTRL_PWMG_EN BIT(10) +#define ASPEED_PTCR_CTRL_PWMF_EN BIT(9) +#define ASPEED_PTCR_CTRL_PWME_EN BIT(8) + +/* ASPEED_PTCR_CLK_EXT_CTRL : 0x44 - Clock Control Extension #1 Register */ +/* TYPE O */ +#define ASPEED_PTCR_CLK_CTRL_TYPEO_MASK GENMASK(15, 0) +#define ASPEED_PTCR_CLK_CTRL_TYPEO_UNIT 8 +#define ASPEED_PTCR_CLK_CTRL_TYPEO_H 4 +#define ASPEED_PTCR_CLK_CTRL_TYPEO_L 0 + +#define PWM_MAX 255 + +#define M_PWM_DIV_H 0x00 +#define M_PWM_DIV_L 0x05 +#define M_PWM_PERIOD 0x5F +#define M_TACH_CLK_DIV 0x00 +#define M_TACH_MODE 0x00 +#define M_TACH_UNIT 0x1000 +#define INIT_FAN_CTRL 0xFF + +struct aspeed_pwm_tacho_regmap { + void __iomem *regs; +}; + +struct aspeed_pwm_tacho_data { + struct regmap *regmap; + unsigned long clk_freq; + bool pwm_present[8]; + bool fan_tach_present[16]; + u8 type_pwm_clock_unit[3]; + u8 type_pwm_clock_division_h[3]; + u8 type_pwm_clock_division_l[3]; + u8 type_fan_tach_clock_division[3]; + u16 type_fan_tach_unit[3]; + u8 pwm_port_type[8]; + u8 pwm_port_fan_ctrl[8]; + u8 fan_tach_ch_source[16]; + const struct attribute_group *groups[2]; +}; + +enum type { TYPEM, TYPEN, TYPEO }; + +struct type_params { + u32 l_value; + u32 h_value; + u32 unit_value; + u32 clk_ctrl_mask; + u32 clk_ctrl_reg; + u32 ctrl_reg; + u32 ctrl_reg1; +}; + +static const struct type_params type_params[] = { + [TYPEM] = { + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEM_L, + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEM_H, + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEM_UNIT, + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEM_MASK, + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL, + .ctrl_reg = ASPEED_PTCR_TYPEM_CTRL, + .ctrl_reg1 = ASPEED_PTCR_TYPEM_CTRL1, + }, + [TYPEN] = { + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEN_L, + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEN_H, + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEN_UNIT, + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEN_MASK, + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL, + .ctrl_reg = ASPEED_PTCR_TYPEN_CTRL, + .ctrl_reg1 = ASPEED_PTCR_TYPEN_CTRL1, + }, + [TYPEO] = { + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEO_L, + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEO_H, + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEO_UNIT, + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEO_MASK, + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL_EXT, + .ctrl_reg = ASPEED_PTCR_TYPEO_CTRL, + .ctrl_reg1 = ASPEED_PTCR_TYPEO_CTRL1, + } +}; + +enum pwm_port { PWMA, PWMB, PWMC, PWMD, PWME, PWMF, PWMG, PWMH }; + +struct pwm_port_params { + u32 pwm_en; + u32 ctrl_reg; + u32 type_part1; + u32 type_part2; + u32 type_mask; + u32 duty_ctrl_rise_point; + u32 duty_ctrl_fall_point; + u32 duty_ctrl_reg; + u32 duty_ctrl_rise_fall_mask; +}; + +static const struct pwm_port_params pwm_port_params[] = { + [PWMA] = { + .pwm_en = ASPEED_PTCR_CTRL_PWMA_EN, + .ctrl_reg = ASPEED_PTCR_CTRL, + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART1, + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART2, + .type_mask = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_MASK, + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, + .duty_ctrl_reg = ASPEED_PTCR_DUTY0_CTRL, + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, + }, + [PWMB] = { + .pwm_en = ASPEED_PTCR_CTRL_PWMB_EN, + .ctrl_reg = ASPEED_PTCR_CTRL, + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART1, + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART2, + .type_mask = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_MASK, + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, + .duty_ctrl_reg = ASPEED_PTCR_DUTY0_CTRL, + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, + }, + [PWMC] = { + .pwm_en = ASPEED_PTCR_CTRL_PWMC_EN, + .ctrl_reg = ASPEED_PTCR_CTRL, + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART1, + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART2, + .type_mask = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_MASK, + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, + .duty_ctrl_reg = ASPEED_PTCR_DUTY1_CTRL, + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, + }, + [PWMD] = { + .pwm_en = ASPEED_PTCR_CTRL_PWMD_EN, + .ctrl_reg = ASPEED_PTCR_CTRL, + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART1, + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART2, + .type_mask = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_MASK, + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, + .duty_ctrl_reg = ASPEED_PTCR_DUTY1_CTRL, + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, + }, + [PWME] = { + .pwm_en = ASPEED_PTCR_CTRL_PWME_EN, + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, + .type_part1 = ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART1, + .type_part2 = ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART2, + .type_mask = ASPEED_PTCR_CTRL_SET_PWME_TYPE_MASK, + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, + .duty_ctrl_reg = ASPEED_PTCR_DUTY2_CTRL, + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, + }, + [PWMF] = { + .pwm_en = ASPEED_PTCR_CTRL_PWMF_EN, + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART1, + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART2, + .type_mask = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_MASK, + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, + .duty_ctrl_reg = ASPEED_PTCR_DUTY2_CTRL, + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, + }, + [PWMG] = { + .pwm_en = ASPEED_PTCR_CTRL_PWMG_EN, + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART1, + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART2, + .type_mask = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_MASK, + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, + .duty_ctrl_reg = ASPEED_PTCR_DUTY3_CTRL, + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, + }, + [PWMH] = { + .pwm_en = ASPEED_PTCR_CTRL_PWMH_EN, + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART1, + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART2, + .type_mask = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_MASK, + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, + .duty_ctrl_reg = ASPEED_PTCR_DUTY3_CTRL, + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, + } +}; + +static int regmap_aspeed_pwm_tacho_reg_write(void *context, unsigned int reg, + unsigned int val) +{ + struct aspeed_pwm_tacho_regmap *hregmap = context; + + writel(val, hregmap->regs + reg); + return 0; +} + +static int regmap_aspeed_pwm_tacho_reg_read(void *context, unsigned int reg, + unsigned int *val) +{ + struct aspeed_pwm_tacho_regmap *hregmap = context; + + *val = readl(hregmap->regs + reg); + return 0; +} + +static const struct regmap_config aspeed_pwm_tacho_regmap_config = { + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, + .max_register = ASPEED_PTCR_TYPEO_LIMIT, + .reg_write = regmap_aspeed_pwm_tacho_reg_write, + .reg_read = regmap_aspeed_pwm_tacho_reg_read, + .fast_io = true, +}; + +static void aspeed_set_clock_enable(struct regmap *regmap, bool val) +{ + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, + ASPEED_PTCR_CTRL_CLK_EN, + val ? ASPEED_PTCR_CTRL_CLK_EN : 0); +} + +static void aspeed_set_clock_source(struct regmap *regmap, int val) +{ + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, + ASPEED_PTCR_CTRL_CLK_SRC, + val ? ASPEED_PTCR_CTRL_CLK_SRC : 0); +} + +static void aspeed_set_pwm_clock_values(struct regmap *regmap, u8 type, + u8 div_high, u8 div_low, u8 unit) +{ + u32 reg_value = ((div_high << type_params[type].h_value) | + (div_low << type_params[type].l_value) | + (unit << type_params[type].unit_value)); + + regmap_update_bits(regmap, type_params[type].clk_ctrl_reg, + type_params[type].clk_ctrl_mask, reg_value); +} + +static void aspeed_set_pwm_port_enable(struct regmap *regmap, u8 pwm_port, + bool enable) +{ + regmap_update_bits(regmap, pwm_port_params[pwm_port].ctrl_reg, + pwm_port_params[pwm_port].pwm_en, + enable ? pwm_port_params[pwm_port].pwm_en : 0); +} + +static void aspeed_set_pwm_port_type(struct regmap *regmap, + u8 pwm_port, u8 type) +{ + u32 reg_value = (type & 0x1) << pwm_port_params[pwm_port].type_part1; + + reg_value |= (type & 0x2) << pwm_port_params[pwm_port].type_part2; + + regmap_update_bits(regmap, pwm_port_params[pwm_port].ctrl_reg, + pwm_port_params[pwm_port].type_mask, reg_value); +} + +static void aspeed_set_pwm_port_duty_rising_falling(struct regmap *regmap, + u8 pwm_port, u8 rising, + u8 falling) +{ + u32 reg_value = (rising << + pwm_port_params[pwm_port].duty_ctrl_rise_point); + reg_value |= (falling << + pwm_port_params[pwm_port].duty_ctrl_fall_point); + + regmap_update_bits(regmap, pwm_port_params[pwm_port].duty_ctrl_reg, + pwm_port_params[pwm_port].duty_ctrl_rise_fall_mask, + reg_value); +} + +static void aspeed_set_tacho_type_enable(struct regmap *regmap, u8 type, + bool enable) +{ + regmap_update_bits(regmap, type_params[type].ctrl_reg, + TYPE_CTRL_FAN_TYPE_EN, + enable ? TYPE_CTRL_FAN_TYPE_EN : 0); +} + +static void aspeed_set_tacho_type_values(struct regmap *regmap, u8 type, + u8 mode, u16 unit, u8 division) +{ + u32 reg_value = ((mode << TYPE_CTRL_FAN_MODE) | + (unit << TYPE_CTRL_FAN_PERIOD) | + (division << TYPE_CTRL_FAN_DIVISION)); + + regmap_update_bits(regmap, type_params[type].ctrl_reg, + TYPE_CTRL_FAN_MASK, reg_value); + regmap_update_bits(regmap, type_params[type].ctrl_reg1, + TYPE_CTRL_FAN1_MASK, unit << 16); +} + +static void aspeed_set_fan_tach_ch_enable(struct regmap *regmap, u8 fan_tach_ch, + bool enable) +{ + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, + ASPEED_PTCR_CTRL_FAN_NUM_EN(fan_tach_ch), + enable ? + ASPEED_PTCR_CTRL_FAN_NUM_EN(fan_tach_ch) : 0); +} + +static void aspeed_set_fan_tach_ch_source(struct regmap *regmap, u8 fan_tach_ch, + u8 fan_tach_ch_source) +{ + u32 reg_value1 = ((fan_tach_ch_source & 0x3) << + TACH_PWM_SOURCE_BIT01(fan_tach_ch)); + u32 reg_value2 = (((fan_tach_ch_source & 0x4) >> 2) << + TACH_PWM_SOURCE_BIT2(fan_tach_ch)); + + regmap_update_bits(regmap, ASPEED_PTCR_TACH_SOURCE, + TACH_PWM_SOURCE_MASK_BIT01(fan_tach_ch), + reg_value1); + + regmap_update_bits(regmap, ASPEED_PTCR_TACH_SOURCE_EXT, + TACH_PWM_SOURCE_MASK_BIT2(fan_tach_ch), + reg_value2); +} + +static void aspeed_set_pwm_port_fan_ctrl(struct aspeed_pwm_tacho_data *priv, + u8 index, u8 fan_ctrl) +{ + u16 period, dc_time_on; + + period = priv->type_pwm_clock_unit[priv->pwm_port_type[index]]; + period += 1; + dc_time_on = (fan_ctrl * period) / PWM_MAX; + + if (dc_time_on == 0) { + aspeed_set_pwm_port_enable(priv->regmap, index, false); + } else { + if (dc_time_on == period) + dc_time_on = 0; + + aspeed_set_pwm_port_duty_rising_falling(priv->regmap, index, 0, + dc_time_on); + aspeed_set_pwm_port_enable(priv->regmap, index, true); + } +} + +static u32 aspeed_get_fan_tach_ch_measure_period(struct aspeed_pwm_tacho_data + *priv, u8 type) +{ + u32 clk; + u16 tacho_unit; + u8 clk_unit, div_h, div_l, tacho_div; + + clk = priv->clk_freq; + clk_unit = priv->type_pwm_clock_unit[type]; + div_h = priv->type_pwm_clock_division_h[type]; + div_h = 0x1 << div_h; + div_l = priv->type_pwm_clock_division_l[type]; + if (div_l == 0) + div_l = 1; + else + div_l = div_l * 2; + + tacho_unit = priv->type_fan_tach_unit[type]; + tacho_div = priv->type_fan_tach_clock_division[type]; + + tacho_div = 0x4 << (tacho_div * 2); + return clk / (clk_unit * div_h * div_l * tacho_div * tacho_unit); +} + +static u32 aspeed_get_fan_tach_ch_rpm(struct aspeed_pwm_tacho_data *priv, + u8 fan_tach_ch) +{ + u32 raw_data, tach_div, clk_source, timeout = 0, sec, val; + u8 fan_tach_ch_source, type; + + regmap_write(priv->regmap, ASPEED_PTCR_TRIGGER, 0); + regmap_write(priv->regmap, ASPEED_PTCR_TRIGGER, 0x1 << fan_tach_ch); + + fan_tach_ch_source = priv->fan_tach_ch_source[fan_tach_ch]; + type = priv->pwm_port_type[fan_tach_ch_source]; + + sec = (1000 / aspeed_get_fan_tach_ch_measure_period(priv, type)); + + msleep(sec); + + regmap_read(priv->regmap, ASPEED_PTCR_RESULT, &val); + while (!(val & RESULT_STATUS_MASK)) { + timeout++; + if (timeout > 1) + return 0; + msleep(sec); + } + + regmap_read(priv->regmap, ASPEED_PTCR_RESULT, &val); + raw_data = val & RESULT_VALUE_MASK; + tach_div = priv->type_fan_tach_clock_division[type]; + + tach_div = 0x4 << (tach_div * 2); + clk_source = priv->clk_freq; + + if (raw_data == 0) + return 0; + else + return (clk_source * 60) / (2 * raw_data * tach_div); +} + +static ssize_t set_pwm(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int index = sensor_attr->index; + int ret; + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); + long fan_ctrl; + + ret = kstrtol(buf, 10, &fan_ctrl); + if (ret != 0) + return ret; + + if (fan_ctrl < 0 || fan_ctrl > PWM_MAX) + return -EINVAL; + + if (priv->pwm_port_fan_ctrl[index] == fan_ctrl) + return count; + + priv->pwm_port_fan_ctrl[index] = fan_ctrl; + aspeed_set_pwm_port_fan_ctrl(priv, index, fan_ctrl); + + return count; +} + +static ssize_t show_pwm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int index = sensor_attr->index; + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); + + return sprintf(buf, "%u\n", priv->pwm_port_fan_ctrl[index]); +} + +static ssize_t show_rpm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int index = sensor_attr->index; + u32 rpm; + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); + + rpm = aspeed_get_fan_tach_ch_rpm(priv, index); + + return sprintf(buf, "%u\n", rpm); +} + +static umode_t pwm_is_visible(struct kobject *kobj, + struct attribute *a, int index) +{ + struct device *dev = container_of(kobj, struct device, kobj); + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); + + if (!priv->pwm_present[index]) + return 0; + return a->mode; +} + +static umode_t fan_dev_is_visible(struct kobject *kobj, + struct attribute *a, int index) +{ + struct device *dev = container_of(kobj, struct device, kobj); + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); + + if (!priv->fan_tach_present[index]) + return 0; + return a->mode; +} + +static SENSOR_DEVICE_ATTR(pwm0, 0644, + show_pwm, set_pwm, 0); +static SENSOR_DEVICE_ATTR(pwm1, 0644, + show_pwm, set_pwm, 1); +static SENSOR_DEVICE_ATTR(pwm2, 0644, + show_pwm, set_pwm, 2); +static SENSOR_DEVICE_ATTR(pwm3, 0644, + show_pwm, set_pwm, 3); +static SENSOR_DEVICE_ATTR(pwm4, 0644, + show_pwm, set_pwm, 4); +static SENSOR_DEVICE_ATTR(pwm5, 0644, + show_pwm, set_pwm, 5); +static SENSOR_DEVICE_ATTR(pwm6, 0644, + show_pwm, set_pwm, 6); +static SENSOR_DEVICE_ATTR(pwm7, 0644, + show_pwm, set_pwm, 7); + +static struct attribute *pwm_dev_attrs[] = { + &sensor_dev_attr_pwm0.dev_attr.attr, + &sensor_dev_attr_pwm1.dev_attr.attr, + &sensor_dev_attr_pwm2.dev_attr.attr, + &sensor_dev_attr_pwm3.dev_attr.attr, + &sensor_dev_attr_pwm4.dev_attr.attr, + &sensor_dev_attr_pwm5.dev_attr.attr, + &sensor_dev_attr_pwm6.dev_attr.attr, + &sensor_dev_attr_pwm7.dev_attr.attr, + NULL, +}; + +static const struct attribute_group pwm_dev_group = { + .attrs = pwm_dev_attrs, + .is_visible = pwm_is_visible, +}; + +static SENSOR_DEVICE_ATTR(fan0_input, 0444, + show_rpm, NULL, 0); +static SENSOR_DEVICE_ATTR(fan1_input, 0444, + show_rpm, NULL, 1); +static SENSOR_DEVICE_ATTR(fan2_input, 0444, + show_rpm, NULL, 2); +static SENSOR_DEVICE_ATTR(fan3_input, 0444, + show_rpm, NULL, 3); +static SENSOR_DEVICE_ATTR(fan4_input, 0444, + show_rpm, NULL, 4); +static SENSOR_DEVICE_ATTR(fan5_input, 0444, + show_rpm, NULL, 5); +static SENSOR_DEVICE_ATTR(fan6_input, 0444, + show_rpm, NULL, 6); +static SENSOR_DEVICE_ATTR(fan7_input, 0444, + show_rpm, NULL, 7); +static SENSOR_DEVICE_ATTR(fan8_input, 0444, + show_rpm, NULL, 8); +static SENSOR_DEVICE_ATTR(fan9_input, 0444, + show_rpm, NULL, 9); +static SENSOR_DEVICE_ATTR(fan10_input, 0444, + show_rpm, NULL, 10); +static SENSOR_DEVICE_ATTR(fan11_input, 0444, + show_rpm, NULL, 11); +static SENSOR_DEVICE_ATTR(fan12_input, 0444, + show_rpm, NULL, 12); +static SENSOR_DEVICE_ATTR(fan13_input, 0444, + show_rpm, NULL, 13); +static SENSOR_DEVICE_ATTR(fan14_input, 0444, + show_rpm, NULL, 14); +static SENSOR_DEVICE_ATTR(fan15_input, 0444, + show_rpm, NULL, 15); + +static struct attribute *fan_dev_attrs[] = { + &sensor_dev_attr_fan0_input.dev_attr.attr, + &sensor_dev_attr_fan1_input.dev_attr.attr, + &sensor_dev_attr_fan2_input.dev_attr.attr, + &sensor_dev_attr_fan3_input.dev_attr.attr, + &sensor_dev_attr_fan4_input.dev_attr.attr, + &sensor_dev_attr_fan5_input.dev_attr.attr, + &sensor_dev_attr_fan6_input.dev_attr.attr, + &sensor_dev_attr_fan7_input.dev_attr.attr, + &sensor_dev_attr_fan8_input.dev_attr.attr, + &sensor_dev_attr_fan9_input.dev_attr.attr, + &sensor_dev_attr_fan10_input.dev_attr.attr, + &sensor_dev_attr_fan11_input.dev_attr.attr, + &sensor_dev_attr_fan12_input.dev_attr.attr, + &sensor_dev_attr_fan13_input.dev_attr.attr, + &sensor_dev_attr_fan14_input.dev_attr.attr, + &sensor_dev_attr_fan15_input.dev_attr.attr, + NULL +}; + +static const struct attribute_group fan_dev_group = { + .attrs = fan_dev_attrs, + .is_visible = fan_dev_is_visible, +}; + +/* + * The clock type is type M : + * The PWM frequency = 24MHz / (type M clock division L bit * + * type M clock division H bit * (type M PWM period bit + 1)) + */ +static void aspeed_create_type(struct aspeed_pwm_tacho_data *priv) +{ + priv->type_pwm_clock_division_h[TYPEM] = M_PWM_DIV_H; + priv->type_pwm_clock_division_l[TYPEM] = M_PWM_DIV_L; + priv->type_pwm_clock_unit[TYPEM] = M_PWM_PERIOD; + aspeed_set_pwm_clock_values(priv->regmap, TYPEM, M_PWM_DIV_H, + M_PWM_DIV_L, M_PWM_PERIOD); + aspeed_set_tacho_type_enable(priv->regmap, TYPEM, true); + priv->type_fan_tach_clock_division[TYPEM] = M_TACH_CLK_DIV; + priv->type_fan_tach_unit[TYPEM] = M_TACH_UNIT; + aspeed_set_tacho_type_values(priv->regmap, TYPEM, M_TACH_MODE, + M_TACH_UNIT, M_TACH_CLK_DIV); +} + +static void aspeed_create_pwm_port(struct aspeed_pwm_tacho_data *priv, + u8 pwm_port) +{ + aspeed_set_pwm_port_enable(priv->regmap, pwm_port, true); + priv->pwm_present[pwm_port] = true; + + priv->pwm_port_type[pwm_port] = TYPEM; + aspeed_set_pwm_port_type(priv->regmap, pwm_port, TYPEM); + + priv->pwm_port_fan_ctrl[pwm_port] = INIT_FAN_CTRL; + aspeed_set_pwm_port_fan_ctrl(priv, pwm_port, INIT_FAN_CTRL); +} + +static void aspeed_create_fan_tach_channel(struct aspeed_pwm_tacho_data *priv, + u8 *fan_tach_ch, + int count, + u8 pwm_source) +{ + u8 val, index; + + for (val = 0; val < count; val++) { + index = fan_tach_ch[val]; + aspeed_set_fan_tach_ch_enable(priv->regmap, index, true); + priv->fan_tach_present[index] = true; + priv->fan_tach_ch_source[index] = pwm_source; + aspeed_set_fan_tach_ch_source(priv->regmap, index, pwm_source); + } +} + +static int aspeed_create_fan(struct device *dev, + struct device_node *child, + struct aspeed_pwm_tacho_data *priv) +{ + u8 *fan_tach_ch; + u32 pwm_port; + int ret, count; + + ret = of_property_read_u32(child, "reg", &pwm_port); + if (ret) + return ret; + aspeed_create_pwm_port(priv, (u8)pwm_port); + + count = of_property_count_u8_elems(child, "aspeed-fan-tach-ch"); + if (count < 1) + return -EINVAL; + fan_tach_ch = devm_kzalloc(dev, sizeof(*fan_tach_ch) * count, + GFP_KERNEL); + if (!fan_tach_ch) + return -ENOMEM; + ret = of_property_read_u8_array(child, "aspeed-fan-tach-ch", + fan_tach_ch, count); + if (ret) + return ret; + aspeed_create_fan_tach_channel(priv, fan_tach_ch, count, pwm_port); + + return 0; +} + +static int aspeed_pwm_tacho_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np, *child; + struct aspeed_pwm_tacho_data *priv; + struct aspeed_pwm_tacho_regmap *hregmap; + struct resource *res; + struct device *hwmon; + struct clk *clk; + int ret; + + np = dev->of_node; + + hregmap = devm_kzalloc(dev, sizeof(*hregmap), GFP_KERNEL); + if (!hregmap) + return -ENOMEM; + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -ENOENT; + hregmap->regs = devm_ioremap_resource(dev, res); + if (IS_ERR(hregmap->regs)) + return PTR_ERR(hregmap->regs); + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + priv->regmap = devm_regmap_init(dev, NULL, hregmap, + &aspeed_pwm_tacho_regmap_config); + if (IS_ERR(priv->regmap)) + return PTR_ERR(priv->regmap); + regmap_write(priv->regmap, ASPEED_PTCR_TACH_SOURCE, 0); + regmap_write(priv->regmap, ASPEED_PTCR_TACH_SOURCE_EXT, 0); + + clk = devm_clk_get(dev, NULL); + if (IS_ERR(clk)) + return -ENODEV; + priv->clk_freq = clk_get_rate(clk); + aspeed_set_clock_enable(priv->regmap, true); + aspeed_set_clock_source(priv->regmap, 0); + + aspeed_create_type(priv); + + for_each_child_of_node(np, child) { + ret = aspeed_create_fan(dev, child, priv); + of_node_put(child); + if (ret) + return ret; + } + of_node_put(np); + + priv->groups[0] = &pwm_dev_group; + priv->groups[1] = &fan_dev_group; + hwmon = devm_hwmon_device_register_with_groups(dev, + "aspeed_pwm_tacho", + priv, priv->groups); + + return PTR_ERR_OR_ZERO(hwmon); +} + +static const struct of_device_id of_pwm_tacho_match_table[] = { + { .compatible = "aspeed,ast2400-pwm-tacho", }, + { .compatible = "aspeed,ast2500-pwm-tacho", }, + {}, +}; +MODULE_DEVICE_TABLE(of, of_pwm_tacho_match_table); + +static struct platform_driver aspeed_pwm_tacho_driver = { + .probe = aspeed_pwm_tacho_probe, + .driver = { + .name = "aspeed_pwm_tacho", + .of_match_table = of_pwm_tacho_match_table, + }, +}; + +module_platform_driver(aspeed_pwm_tacho_driver); + +MODULE_AUTHOR("Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>"); +MODULE_DESCRIPTION("ASPEED PWM and Fan Tacho device driver"); +MODULE_LICENSE("GPL"); -- 2.12.1.578.ge9c3154ca4-goog ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH linux v5 2/2] drivers: hwmon: Support for ASPEED PWM/Fan tach 2017-03-24 18:17 ` [PATCH linux v5 2/2] drivers: hwmon: Support for ASPEED PWM/Fan tach Jaghathiswari Rankappagounder Natarajan @ 2017-03-29 22:15 ` Jaghathiswari Rankappagounder Natarajan [not found] ` <20170324181723.29379-3-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org> 1 sibling, 0 replies; 7+ messages in thread From: Jaghathiswari Rankappagounder Natarajan @ 2017-03-29 22:15 UTC (permalink / raw) To: Joel Stanley, jdelvare, Guenter Roeck, linux-hwmon, linux-kernel, OpenBMC Maillist, Jonathan Corbet, linux-doc, robh+dt, mark.rutland, devicetree Cc: Jaghathiswari Rankappagounder Natarajan Please provide review comments. On Fri, Mar 24, 2017 at 11:17 AM, Jaghathiswari Rankappagounder Natarajan <jaghu@google.com> wrote: > The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports. > The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer > inputs. > The device driver matches on the device tree node. The configuration > values > are read from the device tree and written to the respective registers. > The driver provides a sysfs entries through which the user can > configure the duty-cycle value (ranging from 0 to 100 percent) and read > the > fan tach rpm value. > > Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com> > --- > v5: > - Changed the driver to suit the changes in the device tree documentation > > v4: > - Modified this driver to suit the representation in the devicetree > > v3: > - Only sent out device tree documentation; did not send this driver > > v2: > - Used BIT() > - Used regmap > - Avoided division when raw data is 0 > - Removed empty lines between declaration > - Removed macros; Used two attribute groups and used is_visible callback > - Returned error when properties are undefined > - Removed .owner field > - Used PTR_ERR_OR_ZERO > - Removed explicit of_node_put for child nodes > > Documentation/hwmon/aspeed-pwm-tacho | 22 + > drivers/hwmon/Kconfig | 13 +- > drivers/hwmon/Makefile | 1 + > drivers/hwmon/aspeed-pwm-tacho.c | 854 +++++++++++++++++++++++++++++++++++ > 4 files changed, 888 insertions(+), 2 deletions(-) > create mode 100644 Documentation/hwmon/aspeed-pwm-tacho > create mode 100644 drivers/hwmon/aspeed-pwm-tacho.c > > diff --git a/Documentation/hwmon/aspeed-pwm-tacho b/Documentation/hwmon/aspeed-pwm-tacho > new file mode 100644 > index 000000000000..0e9ec6d5f900 > --- /dev/null > +++ b/Documentation/hwmon/aspeed-pwm-tacho > @@ -0,0 +1,22 @@ > +Kernel driver aspeed-pwm-tacho > +============================== > + > +Supported chips: > + ASPEED AST2400/2500 > + > +Authors: > + <jaghu@google.com> > + > +Description: > +------------ > +This driver implements support for ASPEED AST2400/2500 PWM and Fan Tacho > +controller. The PWM controller supports upto 8 PWM outputs. The Fan tacho > +controller supports upto 16 tachometer inputs. > + > +The driver provides the following sensor accesses in sysfs: > + > +fanX_input ro provide current fan rotation value in RPM as reported > + by the fan to the device. > + > +pwmX rw get or set PWM fan control value. This is an integer > + value between 0(off) and 255(full speed). > diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig > index 45cef3d2c75c..487110f21827 100644 > --- a/drivers/hwmon/Kconfig > +++ b/drivers/hwmon/Kconfig > @@ -341,6 +341,15 @@ config SENSORS_ASB100 > This driver can also be built as a module. If so, the module > will be called asb100. > > +config SENSORS_ASPEED > + tristate "ASPEED AST2400/AST2500 PWM and Fan tach driver" > + help > + This driver provides support for ASPEED AST2400/AST2500 PWM > + and Fan Tacho controllers. > + > + This driver can also be built as a module. If so, the module > + will be called aspeed_pwm_tacho. > + > config SENSORS_ATXP1 > tristate "Attansic ATXP1 VID controller" > depends on I2C > @@ -952,7 +961,7 @@ config SENSORS_LM70 > help > If you say yes here you get support for the National Semiconductor > LM70, LM71, LM74 and Texas Instruments TMP121/TMP123 digital tempera- > - ture sensor chips. > + true sensor chips. > > This driver can also be built as a module. If so, the module > will be called lm70. > @@ -1506,7 +1515,7 @@ config SENSORS_ADS7871 > > config SENSORS_AMC6821 > tristate "Texas Instruments AMC6821" > - depends on I2C > + depends on I2C > help > If you say yes here you get support for the Texas Instruments > AMC6821 hardware monitoring chips. > diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile > index aecf4ba17460..83025cc9bb45 100644 > --- a/drivers/hwmon/Makefile > +++ b/drivers/hwmon/Makefile > @@ -46,6 +46,7 @@ obj-$(CONFIG_SENSORS_ADT7475) += adt7475.o > obj-$(CONFIG_SENSORS_APPLESMC) += applesmc.o > obj-$(CONFIG_SENSORS_ARM_SCPI) += scpi-hwmon.o > obj-$(CONFIG_SENSORS_ASC7621) += asc7621.o > +obj-$(CONFIG_SENSORS_ASPEED) += aspeed-pwm-tacho.o > obj-$(CONFIG_SENSORS_ATXP1) += atxp1.o > obj-$(CONFIG_SENSORS_CORETEMP) += coretemp.o > obj-$(CONFIG_SENSORS_DA9052_ADC)+= da9052-hwmon.o > diff --git a/drivers/hwmon/aspeed-pwm-tacho.c b/drivers/hwmon/aspeed-pwm-tacho.c > new file mode 100644 > index 000000000000..28888cc34555 > --- /dev/null > +++ b/drivers/hwmon/aspeed-pwm-tacho.c > @@ -0,0 +1,854 @@ > +/* > + * Copyright (c) 2016 Google, Inc > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 or later as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/clk.h> > +#include <linux/gpio/consumer.h> > +#include <linux/delay.h> > +#include <linux/hwmon.h> > +#include <linux/hwmon-sysfs.h> > +#include <linux/io.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/of_platform.h> > +#include <linux/of_device.h> > +#include <linux/platform_device.h> > +#include <linux/sysfs.h> > +#include <linux/regmap.h> > + > +/* ASPEED PWM & FAN Tach Register Definition */ > +#define ASPEED_PTCR_CTRL 0x00 > +#define ASPEED_PTCR_CLK_CTRL 0x04 > +#define ASPEED_PTCR_DUTY0_CTRL 0x08 > +#define ASPEED_PTCR_DUTY1_CTRL 0x0c > +#define ASPEED_PTCR_TYPEM_CTRL 0x10 > +#define ASPEED_PTCR_TYPEM_CTRL1 0x14 > +#define ASPEED_PTCR_TYPEN_CTRL 0x18 > +#define ASPEED_PTCR_TYPEN_CTRL1 0x1c > +#define ASPEED_PTCR_TACH_SOURCE 0x20 > +#define ASPEED_PTCR_TRIGGER 0x28 > +#define ASPEED_PTCR_RESULT 0x2c > +#define ASPEED_PTCR_INTR_CTRL 0x30 > +#define ASPEED_PTCR_INTR_STS 0x34 > +#define ASPEED_PTCR_TYPEM_LIMIT 0x38 > +#define ASPEED_PTCR_TYPEN_LIMIT 0x3C > +#define ASPEED_PTCR_CTRL_EXT 0x40 > +#define ASPEED_PTCR_CLK_CTRL_EXT 0x44 > +#define ASPEED_PTCR_DUTY2_CTRL 0x48 > +#define ASPEED_PTCR_DUTY3_CTRL 0x4c > +#define ASPEED_PTCR_TYPEO_CTRL 0x50 > +#define ASPEED_PTCR_TYPEO_CTRL1 0x54 > +#define ASPEED_PTCR_TACH_SOURCE_EXT 0x60 > +#define ASPEED_PTCR_TYPEO_LIMIT 0x78 > + > +/* ASPEED_PTCR_CTRL : 0x00 - General Control Register */ > +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART1 15 > +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART2 6 > +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_MASK (BIT(7) | BIT(15)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART1 14 > +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART2 5 > +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_MASK (BIT(6) | BIT(14)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART1 13 > +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART2 4 > +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_MASK (BIT(5) | BIT(13)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART1 12 > +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART2 3 > +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_MASK (BIT(4) | BIT(12)) > + > +#define ASPEED_PTCR_CTRL_FAN_NUM_EN(x) BIT(16 + (x)) > + > +#define ASPEED_PTCR_CTRL_PWMD_EN BIT(11) > +#define ASPEED_PTCR_CTRL_PWMC_EN BIT(10) > +#define ASPEED_PTCR_CTRL_PWMB_EN BIT(9) > +#define ASPEED_PTCR_CTRL_PWMA_EN BIT(8) > + > +#define ASPEED_PTCR_CTRL_CLK_SRC BIT(1) > +#define ASPEED_PTCR_CTRL_CLK_EN BIT(0) > + > +/* ASPEED_PTCR_CLK_CTRL : 0x04 - Clock Control Register */ > +/* TYPE N */ > +#define ASPEED_PTCR_CLK_CTRL_TYPEN_MASK GENMASK(31, 16) > +#define ASPEED_PTCR_CLK_CTRL_TYPEN_UNIT 24 > +#define ASPEED_PTCR_CLK_CTRL_TYPEN_H 20 > +#define ASPEED_PTCR_CLK_CTRL_TYPEN_L 16 > +/* TYPE M */ > +#define ASPEED_PTCR_CLK_CTRL_TYPEM_MASK GENMASK(15, 0) > +#define ASPEED_PTCR_CLK_CTRL_TYPEM_UNIT 8 > +#define ASPEED_PTCR_CLK_CTRL_TYPEM_H 4 > +#define ASPEED_PTCR_CLK_CTRL_TYPEM_L 0 > + > +/* > + * ASPEED_PTCR_DUTY_CTRL/1/2/3 : 0x08/0x0C/0x48/0x4C - PWM-FAN duty control > + * 0/1/2/3 register > + */ > +#define DUTY_CTRL_PWM2_FALL_POINT 24 > +#define DUTY_CTRL_PWM2_RISE_POINT 16 > +#define DUTY_CTRL_PWM2_RISE_FALL_MASK GENMASK(31, 16) > +#define DUTY_CTRL_PWM1_FALL_POINT 8 > +#define DUTY_CTRL_PWM1_RISE_POINT 0 > +#define DUTY_CTRL_PWM1_RISE_FALL_MASK GENMASK(15, 0) > + > +/* ASPEED_PTCR_TYPEM_CTRL : 0x10/0x18/0x50 - Type M/N/O Ctrl 0 Register */ > +#define TYPE_CTRL_FAN_MASK (GENMASK(5, 1) | GENMASK(31, 16)) > +#define TYPE_CTRL_FAN1_MASK GENMASK(31, 0) > +#define TYPE_CTRL_FAN_PERIOD 16 > +#define TYPE_CTRL_FAN_MODE 4 > +#define TYPE_CTRL_FAN_DIVISION 1 > +#define TYPE_CTRL_FAN_TYPE_EN 1 > + > +/* ASPEED_PTCR_TACH_SOURCE : 0x20/0x60 - Tach Source Register */ > +/* bit [0,1] at 0x20, bit [2] at 0x60 */ > +#define TACH_PWM_SOURCE_BIT01(x) ((x) * 2) > +#define TACH_PWM_SOURCE_BIT2(x) ((x) * 2) > +#define TACH_PWM_SOURCE_MASK_BIT01(x) (0x3 << ((x) * 2)) > +#define TACH_PWM_SOURCE_MASK_BIT2(x) BIT((x) * 2) > + > +/* ASPEED_PTCR_RESULT : 0x2c - Result Register */ > +#define RESULT_STATUS_MASK BIT(31) > +#define RESULT_VALUE_MASK 0xfffff > + > +/* ASPEED_PTCR_CTRL_EXT : 0x40 - General Control Extension #1 Register */ > +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART1 15 > +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART2 6 > +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_MASK (BIT(7) | BIT(15)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART1 14 > +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART2 5 > +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_MASK (BIT(6) | BIT(14)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART1 13 > +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART2 4 > +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_MASK (BIT(5) | BIT(13)) > + > +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART1 12 > +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART2 3 > +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_MASK (BIT(4) | BIT(12)) > + > +#define ASPEED_PTCR_CTRL_PWMH_EN BIT(11) > +#define ASPEED_PTCR_CTRL_PWMG_EN BIT(10) > +#define ASPEED_PTCR_CTRL_PWMF_EN BIT(9) > +#define ASPEED_PTCR_CTRL_PWME_EN BIT(8) > + > +/* ASPEED_PTCR_CLK_EXT_CTRL : 0x44 - Clock Control Extension #1 Register */ > +/* TYPE O */ > +#define ASPEED_PTCR_CLK_CTRL_TYPEO_MASK GENMASK(15, 0) > +#define ASPEED_PTCR_CLK_CTRL_TYPEO_UNIT 8 > +#define ASPEED_PTCR_CLK_CTRL_TYPEO_H 4 > +#define ASPEED_PTCR_CLK_CTRL_TYPEO_L 0 > + > +#define PWM_MAX 255 > + > +#define M_PWM_DIV_H 0x00 > +#define M_PWM_DIV_L 0x05 > +#define M_PWM_PERIOD 0x5F > +#define M_TACH_CLK_DIV 0x00 > +#define M_TACH_MODE 0x00 > +#define M_TACH_UNIT 0x1000 > +#define INIT_FAN_CTRL 0xFF > + > +struct aspeed_pwm_tacho_regmap { > + void __iomem *regs; > +}; > + > +struct aspeed_pwm_tacho_data { > + struct regmap *regmap; > + unsigned long clk_freq; > + bool pwm_present[8]; > + bool fan_tach_present[16]; > + u8 type_pwm_clock_unit[3]; > + u8 type_pwm_clock_division_h[3]; > + u8 type_pwm_clock_division_l[3]; > + u8 type_fan_tach_clock_division[3]; > + u16 type_fan_tach_unit[3]; > + u8 pwm_port_type[8]; > + u8 pwm_port_fan_ctrl[8]; > + u8 fan_tach_ch_source[16]; > + const struct attribute_group *groups[2]; > +}; > + > +enum type { TYPEM, TYPEN, TYPEO }; > + > +struct type_params { > + u32 l_value; > + u32 h_value; > + u32 unit_value; > + u32 clk_ctrl_mask; > + u32 clk_ctrl_reg; > + u32 ctrl_reg; > + u32 ctrl_reg1; > +}; > + > +static const struct type_params type_params[] = { > + [TYPEM] = { > + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEM_L, > + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEM_H, > + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEM_UNIT, > + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEM_MASK, > + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL, > + .ctrl_reg = ASPEED_PTCR_TYPEM_CTRL, > + .ctrl_reg1 = ASPEED_PTCR_TYPEM_CTRL1, > + }, > + [TYPEN] = { > + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEN_L, > + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEN_H, > + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEN_UNIT, > + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEN_MASK, > + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL, > + .ctrl_reg = ASPEED_PTCR_TYPEN_CTRL, > + .ctrl_reg1 = ASPEED_PTCR_TYPEN_CTRL1, > + }, > + [TYPEO] = { > + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEO_L, > + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEO_H, > + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEO_UNIT, > + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEO_MASK, > + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL_EXT, > + .ctrl_reg = ASPEED_PTCR_TYPEO_CTRL, > + .ctrl_reg1 = ASPEED_PTCR_TYPEO_CTRL1, > + } > +}; > + > +enum pwm_port { PWMA, PWMB, PWMC, PWMD, PWME, PWMF, PWMG, PWMH }; > + > +struct pwm_port_params { > + u32 pwm_en; > + u32 ctrl_reg; > + u32 type_part1; > + u32 type_part2; > + u32 type_mask; > + u32 duty_ctrl_rise_point; > + u32 duty_ctrl_fall_point; > + u32 duty_ctrl_reg; > + u32 duty_ctrl_rise_fall_mask; > +}; > + > +static const struct pwm_port_params pwm_port_params[] = { > + [PWMA] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMA_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY0_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, > + }, > + [PWMB] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMB_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY0_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, > + }, > + [PWMC] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMC_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY1_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, > + }, > + [PWMD] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMD_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY1_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, > + }, > + [PWME] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWME_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWME_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY2_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, > + }, > + [PWMF] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMF_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY2_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, > + }, > + [PWMG] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMG_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY3_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, > + }, > + [PWMH] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMH_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY3_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, > + } > +}; > + > +static int regmap_aspeed_pwm_tacho_reg_write(void *context, unsigned int reg, > + unsigned int val) > +{ > + struct aspeed_pwm_tacho_regmap *hregmap = context; > + > + writel(val, hregmap->regs + reg); > + return 0; > +} > + > +static int regmap_aspeed_pwm_tacho_reg_read(void *context, unsigned int reg, > + unsigned int *val) > +{ > + struct aspeed_pwm_tacho_regmap *hregmap = context; > + > + *val = readl(hregmap->regs + reg); > + return 0; > +} > + > +static const struct regmap_config aspeed_pwm_tacho_regmap_config = { > + .reg_bits = 32, > + .val_bits = 32, > + .reg_stride = 4, > + .max_register = ASPEED_PTCR_TYPEO_LIMIT, > + .reg_write = regmap_aspeed_pwm_tacho_reg_write, > + .reg_read = regmap_aspeed_pwm_tacho_reg_read, > + .fast_io = true, > +}; > + > +static void aspeed_set_clock_enable(struct regmap *regmap, bool val) > +{ > + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, > + ASPEED_PTCR_CTRL_CLK_EN, > + val ? ASPEED_PTCR_CTRL_CLK_EN : 0); > +} > + > +static void aspeed_set_clock_source(struct regmap *regmap, int val) > +{ > + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, > + ASPEED_PTCR_CTRL_CLK_SRC, > + val ? ASPEED_PTCR_CTRL_CLK_SRC : 0); > +} > + > +static void aspeed_set_pwm_clock_values(struct regmap *regmap, u8 type, > + u8 div_high, u8 div_low, u8 unit) > +{ > + u32 reg_value = ((div_high << type_params[type].h_value) | > + (div_low << type_params[type].l_value) | > + (unit << type_params[type].unit_value)); > + > + regmap_update_bits(regmap, type_params[type].clk_ctrl_reg, > + type_params[type].clk_ctrl_mask, reg_value); > +} > + > +static void aspeed_set_pwm_port_enable(struct regmap *regmap, u8 pwm_port, > + bool enable) > +{ > + regmap_update_bits(regmap, pwm_port_params[pwm_port].ctrl_reg, > + pwm_port_params[pwm_port].pwm_en, > + enable ? pwm_port_params[pwm_port].pwm_en : 0); > +} > + > +static void aspeed_set_pwm_port_type(struct regmap *regmap, > + u8 pwm_port, u8 type) > +{ > + u32 reg_value = (type & 0x1) << pwm_port_params[pwm_port].type_part1; > + > + reg_value |= (type & 0x2) << pwm_port_params[pwm_port].type_part2; > + > + regmap_update_bits(regmap, pwm_port_params[pwm_port].ctrl_reg, > + pwm_port_params[pwm_port].type_mask, reg_value); > +} > + > +static void aspeed_set_pwm_port_duty_rising_falling(struct regmap *regmap, > + u8 pwm_port, u8 rising, > + u8 falling) > +{ > + u32 reg_value = (rising << > + pwm_port_params[pwm_port].duty_ctrl_rise_point); > + reg_value |= (falling << > + pwm_port_params[pwm_port].duty_ctrl_fall_point); > + > + regmap_update_bits(regmap, pwm_port_params[pwm_port].duty_ctrl_reg, > + pwm_port_params[pwm_port].duty_ctrl_rise_fall_mask, > + reg_value); > +} > + > +static void aspeed_set_tacho_type_enable(struct regmap *regmap, u8 type, > + bool enable) > +{ > + regmap_update_bits(regmap, type_params[type].ctrl_reg, > + TYPE_CTRL_FAN_TYPE_EN, > + enable ? TYPE_CTRL_FAN_TYPE_EN : 0); > +} > + > +static void aspeed_set_tacho_type_values(struct regmap *regmap, u8 type, > + u8 mode, u16 unit, u8 division) > +{ > + u32 reg_value = ((mode << TYPE_CTRL_FAN_MODE) | > + (unit << TYPE_CTRL_FAN_PERIOD) | > + (division << TYPE_CTRL_FAN_DIVISION)); > + > + regmap_update_bits(regmap, type_params[type].ctrl_reg, > + TYPE_CTRL_FAN_MASK, reg_value); > + regmap_update_bits(regmap, type_params[type].ctrl_reg1, > + TYPE_CTRL_FAN1_MASK, unit << 16); > +} > + > +static void aspeed_set_fan_tach_ch_enable(struct regmap *regmap, u8 fan_tach_ch, > + bool enable) > +{ > + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, > + ASPEED_PTCR_CTRL_FAN_NUM_EN(fan_tach_ch), > + enable ? > + ASPEED_PTCR_CTRL_FAN_NUM_EN(fan_tach_ch) : 0); > +} > + > +static void aspeed_set_fan_tach_ch_source(struct regmap *regmap, u8 fan_tach_ch, > + u8 fan_tach_ch_source) > +{ > + u32 reg_value1 = ((fan_tach_ch_source & 0x3) << > + TACH_PWM_SOURCE_BIT01(fan_tach_ch)); > + u32 reg_value2 = (((fan_tach_ch_source & 0x4) >> 2) << > + TACH_PWM_SOURCE_BIT2(fan_tach_ch)); > + > + regmap_update_bits(regmap, ASPEED_PTCR_TACH_SOURCE, > + TACH_PWM_SOURCE_MASK_BIT01(fan_tach_ch), > + reg_value1); > + > + regmap_update_bits(regmap, ASPEED_PTCR_TACH_SOURCE_EXT, > + TACH_PWM_SOURCE_MASK_BIT2(fan_tach_ch), > + reg_value2); > +} > + > +static void aspeed_set_pwm_port_fan_ctrl(struct aspeed_pwm_tacho_data *priv, > + u8 index, u8 fan_ctrl) > +{ > + u16 period, dc_time_on; > + > + period = priv->type_pwm_clock_unit[priv->pwm_port_type[index]]; > + period += 1; > + dc_time_on = (fan_ctrl * period) / PWM_MAX; > + > + if (dc_time_on == 0) { > + aspeed_set_pwm_port_enable(priv->regmap, index, false); > + } else { > + if (dc_time_on == period) > + dc_time_on = 0; > + > + aspeed_set_pwm_port_duty_rising_falling(priv->regmap, index, 0, > + dc_time_on); > + aspeed_set_pwm_port_enable(priv->regmap, index, true); > + } > +} > + > +static u32 aspeed_get_fan_tach_ch_measure_period(struct aspeed_pwm_tacho_data > + *priv, u8 type) > +{ > + u32 clk; > + u16 tacho_unit; > + u8 clk_unit, div_h, div_l, tacho_div; > + > + clk = priv->clk_freq; > + clk_unit = priv->type_pwm_clock_unit[type]; > + div_h = priv->type_pwm_clock_division_h[type]; > + div_h = 0x1 << div_h; > + div_l = priv->type_pwm_clock_division_l[type]; > + if (div_l == 0) > + div_l = 1; > + else > + div_l = div_l * 2; > + > + tacho_unit = priv->type_fan_tach_unit[type]; > + tacho_div = priv->type_fan_tach_clock_division[type]; > + > + tacho_div = 0x4 << (tacho_div * 2); > + return clk / (clk_unit * div_h * div_l * tacho_div * tacho_unit); > +} > + > +static u32 aspeed_get_fan_tach_ch_rpm(struct aspeed_pwm_tacho_data *priv, > + u8 fan_tach_ch) > +{ > + u32 raw_data, tach_div, clk_source, timeout = 0, sec, val; > + u8 fan_tach_ch_source, type; > + > + regmap_write(priv->regmap, ASPEED_PTCR_TRIGGER, 0); > + regmap_write(priv->regmap, ASPEED_PTCR_TRIGGER, 0x1 << fan_tach_ch); > + > + fan_tach_ch_source = priv->fan_tach_ch_source[fan_tach_ch]; > + type = priv->pwm_port_type[fan_tach_ch_source]; > + > + sec = (1000 / aspeed_get_fan_tach_ch_measure_period(priv, type)); > + > + msleep(sec); > + > + regmap_read(priv->regmap, ASPEED_PTCR_RESULT, &val); > + while (!(val & RESULT_STATUS_MASK)) { > + timeout++; > + if (timeout > 1) > + return 0; > + msleep(sec); > + } > + > + regmap_read(priv->regmap, ASPEED_PTCR_RESULT, &val); > + raw_data = val & RESULT_VALUE_MASK; > + tach_div = priv->type_fan_tach_clock_division[type]; > + > + tach_div = 0x4 << (tach_div * 2); > + clk_source = priv->clk_freq; > + > + if (raw_data == 0) > + return 0; > + else > + return (clk_source * 60) / (2 * raw_data * tach_div); > +} > + > +static ssize_t set_pwm(struct device *dev, struct device_attribute *attr, > + const char *buf, size_t count) > +{ > + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); > + int index = sensor_attr->index; > + int ret; > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + long fan_ctrl; > + > + ret = kstrtol(buf, 10, &fan_ctrl); > + if (ret != 0) > + return ret; > + > + if (fan_ctrl < 0 || fan_ctrl > PWM_MAX) > + return -EINVAL; > + > + if (priv->pwm_port_fan_ctrl[index] == fan_ctrl) > + return count; > + > + priv->pwm_port_fan_ctrl[index] = fan_ctrl; > + aspeed_set_pwm_port_fan_ctrl(priv, index, fan_ctrl); > + > + return count; > +} > + > +static ssize_t show_pwm(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); > + int index = sensor_attr->index; > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + > + return sprintf(buf, "%u\n", priv->pwm_port_fan_ctrl[index]); > +} > + > +static ssize_t show_rpm(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); > + int index = sensor_attr->index; > + u32 rpm; > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + > + rpm = aspeed_get_fan_tach_ch_rpm(priv, index); > + > + return sprintf(buf, "%u\n", rpm); > +} > + > +static umode_t pwm_is_visible(struct kobject *kobj, > + struct attribute *a, int index) > +{ > + struct device *dev = container_of(kobj, struct device, kobj); > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + > + if (!priv->pwm_present[index]) > + return 0; > + return a->mode; > +} > + > +static umode_t fan_dev_is_visible(struct kobject *kobj, > + struct attribute *a, int index) > +{ > + struct device *dev = container_of(kobj, struct device, kobj); > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + > + if (!priv->fan_tach_present[index]) > + return 0; > + return a->mode; > +} > + > +static SENSOR_DEVICE_ATTR(pwm0, 0644, > + show_pwm, set_pwm, 0); > +static SENSOR_DEVICE_ATTR(pwm1, 0644, > + show_pwm, set_pwm, 1); > +static SENSOR_DEVICE_ATTR(pwm2, 0644, > + show_pwm, set_pwm, 2); > +static SENSOR_DEVICE_ATTR(pwm3, 0644, > + show_pwm, set_pwm, 3); > +static SENSOR_DEVICE_ATTR(pwm4, 0644, > + show_pwm, set_pwm, 4); > +static SENSOR_DEVICE_ATTR(pwm5, 0644, > + show_pwm, set_pwm, 5); > +static SENSOR_DEVICE_ATTR(pwm6, 0644, > + show_pwm, set_pwm, 6); > +static SENSOR_DEVICE_ATTR(pwm7, 0644, > + show_pwm, set_pwm, 7); > + > +static struct attribute *pwm_dev_attrs[] = { > + &sensor_dev_attr_pwm0.dev_attr.attr, > + &sensor_dev_attr_pwm1.dev_attr.attr, > + &sensor_dev_attr_pwm2.dev_attr.attr, > + &sensor_dev_attr_pwm3.dev_attr.attr, > + &sensor_dev_attr_pwm4.dev_attr.attr, > + &sensor_dev_attr_pwm5.dev_attr.attr, > + &sensor_dev_attr_pwm6.dev_attr.attr, > + &sensor_dev_attr_pwm7.dev_attr.attr, > + NULL, > +}; > + > +static const struct attribute_group pwm_dev_group = { > + .attrs = pwm_dev_attrs, > + .is_visible = pwm_is_visible, > +}; > + > +static SENSOR_DEVICE_ATTR(fan0_input, 0444, > + show_rpm, NULL, 0); > +static SENSOR_DEVICE_ATTR(fan1_input, 0444, > + show_rpm, NULL, 1); > +static SENSOR_DEVICE_ATTR(fan2_input, 0444, > + show_rpm, NULL, 2); > +static SENSOR_DEVICE_ATTR(fan3_input, 0444, > + show_rpm, NULL, 3); > +static SENSOR_DEVICE_ATTR(fan4_input, 0444, > + show_rpm, NULL, 4); > +static SENSOR_DEVICE_ATTR(fan5_input, 0444, > + show_rpm, NULL, 5); > +static SENSOR_DEVICE_ATTR(fan6_input, 0444, > + show_rpm, NULL, 6); > +static SENSOR_DEVICE_ATTR(fan7_input, 0444, > + show_rpm, NULL, 7); > +static SENSOR_DEVICE_ATTR(fan8_input, 0444, > + show_rpm, NULL, 8); > +static SENSOR_DEVICE_ATTR(fan9_input, 0444, > + show_rpm, NULL, 9); > +static SENSOR_DEVICE_ATTR(fan10_input, 0444, > + show_rpm, NULL, 10); > +static SENSOR_DEVICE_ATTR(fan11_input, 0444, > + show_rpm, NULL, 11); > +static SENSOR_DEVICE_ATTR(fan12_input, 0444, > + show_rpm, NULL, 12); > +static SENSOR_DEVICE_ATTR(fan13_input, 0444, > + show_rpm, NULL, 13); > +static SENSOR_DEVICE_ATTR(fan14_input, 0444, > + show_rpm, NULL, 14); > +static SENSOR_DEVICE_ATTR(fan15_input, 0444, > + show_rpm, NULL, 15); > + > +static struct attribute *fan_dev_attrs[] = { > + &sensor_dev_attr_fan0_input.dev_attr.attr, > + &sensor_dev_attr_fan1_input.dev_attr.attr, > + &sensor_dev_attr_fan2_input.dev_attr.attr, > + &sensor_dev_attr_fan3_input.dev_attr.attr, > + &sensor_dev_attr_fan4_input.dev_attr.attr, > + &sensor_dev_attr_fan5_input.dev_attr.attr, > + &sensor_dev_attr_fan6_input.dev_attr.attr, > + &sensor_dev_attr_fan7_input.dev_attr.attr, > + &sensor_dev_attr_fan8_input.dev_attr.attr, > + &sensor_dev_attr_fan9_input.dev_attr.attr, > + &sensor_dev_attr_fan10_input.dev_attr.attr, > + &sensor_dev_attr_fan11_input.dev_attr.attr, > + &sensor_dev_attr_fan12_input.dev_attr.attr, > + &sensor_dev_attr_fan13_input.dev_attr.attr, > + &sensor_dev_attr_fan14_input.dev_attr.attr, > + &sensor_dev_attr_fan15_input.dev_attr.attr, > + NULL > +}; > + > +static const struct attribute_group fan_dev_group = { > + .attrs = fan_dev_attrs, > + .is_visible = fan_dev_is_visible, > +}; > + > +/* > + * The clock type is type M : > + * The PWM frequency = 24MHz / (type M clock division L bit * > + * type M clock division H bit * (type M PWM period bit + 1)) > + */ > +static void aspeed_create_type(struct aspeed_pwm_tacho_data *priv) > +{ > + priv->type_pwm_clock_division_h[TYPEM] = M_PWM_DIV_H; > + priv->type_pwm_clock_division_l[TYPEM] = M_PWM_DIV_L; > + priv->type_pwm_clock_unit[TYPEM] = M_PWM_PERIOD; > + aspeed_set_pwm_clock_values(priv->regmap, TYPEM, M_PWM_DIV_H, > + M_PWM_DIV_L, M_PWM_PERIOD); > + aspeed_set_tacho_type_enable(priv->regmap, TYPEM, true); > + priv->type_fan_tach_clock_division[TYPEM] = M_TACH_CLK_DIV; > + priv->type_fan_tach_unit[TYPEM] = M_TACH_UNIT; > + aspeed_set_tacho_type_values(priv->regmap, TYPEM, M_TACH_MODE, > + M_TACH_UNIT, M_TACH_CLK_DIV); > +} > + > +static void aspeed_create_pwm_port(struct aspeed_pwm_tacho_data *priv, > + u8 pwm_port) > +{ > + aspeed_set_pwm_port_enable(priv->regmap, pwm_port, true); > + priv->pwm_present[pwm_port] = true; > + > + priv->pwm_port_type[pwm_port] = TYPEM; > + aspeed_set_pwm_port_type(priv->regmap, pwm_port, TYPEM); > + > + priv->pwm_port_fan_ctrl[pwm_port] = INIT_FAN_CTRL; > + aspeed_set_pwm_port_fan_ctrl(priv, pwm_port, INIT_FAN_CTRL); > +} > + > +static void aspeed_create_fan_tach_channel(struct aspeed_pwm_tacho_data *priv, > + u8 *fan_tach_ch, > + int count, > + u8 pwm_source) > +{ > + u8 val, index; > + > + for (val = 0; val < count; val++) { > + index = fan_tach_ch[val]; > + aspeed_set_fan_tach_ch_enable(priv->regmap, index, true); > + priv->fan_tach_present[index] = true; > + priv->fan_tach_ch_source[index] = pwm_source; > + aspeed_set_fan_tach_ch_source(priv->regmap, index, pwm_source); > + } > +} > + > +static int aspeed_create_fan(struct device *dev, > + struct device_node *child, > + struct aspeed_pwm_tacho_data *priv) > +{ > + u8 *fan_tach_ch; > + u32 pwm_port; > + int ret, count; > + > + ret = of_property_read_u32(child, "reg", &pwm_port); > + if (ret) > + return ret; > + aspeed_create_pwm_port(priv, (u8)pwm_port); > + > + count = of_property_count_u8_elems(child, "aspeed-fan-tach-ch"); > + if (count < 1) > + return -EINVAL; > + fan_tach_ch = devm_kzalloc(dev, sizeof(*fan_tach_ch) * count, > + GFP_KERNEL); > + if (!fan_tach_ch) > + return -ENOMEM; > + ret = of_property_read_u8_array(child, "aspeed-fan-tach-ch", > + fan_tach_ch, count); > + if (ret) > + return ret; > + aspeed_create_fan_tach_channel(priv, fan_tach_ch, count, pwm_port); > + > + return 0; > +} > + > +static int aspeed_pwm_tacho_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct device_node *np, *child; > + struct aspeed_pwm_tacho_data *priv; > + struct aspeed_pwm_tacho_regmap *hregmap; > + struct resource *res; > + struct device *hwmon; > + struct clk *clk; > + int ret; > + > + np = dev->of_node; > + > + hregmap = devm_kzalloc(dev, sizeof(*hregmap), GFP_KERNEL); > + if (!hregmap) > + return -ENOMEM; > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + if (!res) > + return -ENOENT; > + hregmap->regs = devm_ioremap_resource(dev, res); > + if (IS_ERR(hregmap->regs)) > + return PTR_ERR(hregmap->regs); > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); > + if (!priv) > + return -ENOMEM; > + priv->regmap = devm_regmap_init(dev, NULL, hregmap, > + &aspeed_pwm_tacho_regmap_config); > + if (IS_ERR(priv->regmap)) > + return PTR_ERR(priv->regmap); > + regmap_write(priv->regmap, ASPEED_PTCR_TACH_SOURCE, 0); > + regmap_write(priv->regmap, ASPEED_PTCR_TACH_SOURCE_EXT, 0); > + > + clk = devm_clk_get(dev, NULL); > + if (IS_ERR(clk)) > + return -ENODEV; > + priv->clk_freq = clk_get_rate(clk); > + aspeed_set_clock_enable(priv->regmap, true); > + aspeed_set_clock_source(priv->regmap, 0); > + > + aspeed_create_type(priv); > + > + for_each_child_of_node(np, child) { > + ret = aspeed_create_fan(dev, child, priv); > + of_node_put(child); > + if (ret) > + return ret; > + } > + of_node_put(np); > + > + priv->groups[0] = &pwm_dev_group; > + priv->groups[1] = &fan_dev_group; > + hwmon = devm_hwmon_device_register_with_groups(dev, > + "aspeed_pwm_tacho", > + priv, priv->groups); > + > + return PTR_ERR_OR_ZERO(hwmon); > +} > + > +static const struct of_device_id of_pwm_tacho_match_table[] = { > + { .compatible = "aspeed,ast2400-pwm-tacho", }, > + { .compatible = "aspeed,ast2500-pwm-tacho", }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, of_pwm_tacho_match_table); > + > +static struct platform_driver aspeed_pwm_tacho_driver = { > + .probe = aspeed_pwm_tacho_probe, > + .driver = { > + .name = "aspeed_pwm_tacho", > + .of_match_table = of_pwm_tacho_match_table, > + }, > +}; > + > +module_platform_driver(aspeed_pwm_tacho_driver); > + > +MODULE_AUTHOR("Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>"); > +MODULE_DESCRIPTION("ASPEED PWM and Fan Tacho device driver"); > +MODULE_LICENSE("GPL"); > -- > 2.12.1.578.ge9c3154ca4-goog > ^ permalink raw reply [flat|nested] 7+ messages in thread
[parent not found: <20170324181723.29379-3-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>]
* Re: [PATCH linux v5 2/2] drivers: hwmon: Support for ASPEED PWM/Fan tach [not found] ` <20170324181723.29379-3-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org> @ 2017-04-01 22:45 ` Guenter Roeck 0 siblings, 0 replies; 7+ messages in thread From: Guenter Roeck @ 2017-04-01 22:45 UTC (permalink / raw) To: Jaghathiswari Rankappagounder Natarajan, joel-U3u1mxZcP9KHXe+LvDLADg, jdelvare-IBi9RG/b67k, linux-hwmon-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA, openbmc-uLR06cmDAlY/bJ5BZ2RsiQ, corbet-T1hC0tSOHrs, linux-doc-u79uwXL29TY76Z2rM5mHXA, robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8, devicetree-u79uwXL29TY76Z2rM5mHXA On 03/24/2017 11:17 AM, Jaghathiswari Rankappagounder Natarajan wrote: > The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports. > The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer > inputs. > The device driver matches on the device tree node. The configuration > values > are read from the device tree and written to the respective registers. > The driver provides a sysfs entries through which the user can > configure the duty-cycle value (ranging from 0 to 100 percent) and read > the > fan tach rpm value. > Odd line breaks. > Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org> > --- > v5: > - Changed the driver to suit the changes in the device tree documentation > > v4: > - Modified this driver to suit the representation in the devicetree > > v3: > - Only sent out device tree documentation; did not send this driver > > v2: > - Used BIT() > - Used regmap > - Avoided division when raw data is 0 > - Removed empty lines between declaration > - Removed macros; Used two attribute groups and used is_visible callback > - Returned error when properties are undefined > - Removed .owner field > - Used PTR_ERR_OR_ZERO > - Removed explicit of_node_put for child nodes > > Documentation/hwmon/aspeed-pwm-tacho | 22 + > drivers/hwmon/Kconfig | 13 +- > drivers/hwmon/Makefile | 1 + > drivers/hwmon/aspeed-pwm-tacho.c | 854 +++++++++++++++++++++++++++++++++++ > 4 files changed, 888 insertions(+), 2 deletions(-) > create mode 100644 Documentation/hwmon/aspeed-pwm-tacho > create mode 100644 drivers/hwmon/aspeed-pwm-tacho.c > > diff --git a/Documentation/hwmon/aspeed-pwm-tacho b/Documentation/hwmon/aspeed-pwm-tacho > new file mode 100644 > index 000000000000..0e9ec6d5f900 > --- /dev/null > +++ b/Documentation/hwmon/aspeed-pwm-tacho > @@ -0,0 +1,22 @@ > +Kernel driver aspeed-pwm-tacho > +============================== > + > +Supported chips: > + ASPEED AST2400/2500 > + > +Authors: > + <jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org> > + > +Description: > +------------ > +This driver implements support for ASPEED AST2400/2500 PWM and Fan Tacho > +controller. The PWM controller supports upto 8 PWM outputs. The Fan tacho > +controller supports upto 16 tachometer inputs. > + up to > +The driver provides the following sensor accesses in sysfs: > + > +fanX_input ro provide current fan rotation value in RPM as reported > + by the fan to the device. > + > +pwmX rw get or set PWM fan control value. This is an integer > + value between 0(off) and 255(full speed). > diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig > index 45cef3d2c75c..487110f21827 100644 > --- a/drivers/hwmon/Kconfig > +++ b/drivers/hwmon/Kconfig > @@ -341,6 +341,15 @@ config SENSORS_ASB100 > This driver can also be built as a module. If so, the module > will be called asb100. > > +config SENSORS_ASPEED > + tristate "ASPEED AST2400/AST2500 PWM and Fan tach driver" > + help > + This driver provides support for ASPEED AST2400/AST2500 PWM > + and Fan Tacho controllers. > + > + This driver can also be built as a module. If so, the module > + will be called aspeed_pwm_tacho. > + > config SENSORS_ATXP1 > tristate "Attansic ATXP1 VID controller" > depends on I2C > @@ -952,7 +961,7 @@ config SENSORS_LM70 > help > If you say yes here you get support for the National Semiconductor > LM70, LM71, LM74 and Texas Instruments TMP121/TMP123 digital tempera- > - ture sensor chips. > + true sensor chips. Unrelated. Please drop. Separate patch would be appreciated, of course. > > This driver can also be built as a module. If so, the module > will be called lm70. > @@ -1506,7 +1515,7 @@ config SENSORS_ADS7871 > > config SENSORS_AMC6821 > tristate "Texas Instruments AMC6821" > - depends on I2C > + depends on I2C Unrelated. Please drop. > help > If you say yes here you get support for the Texas Instruments > AMC6821 hardware monitoring chips. > diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile > index aecf4ba17460..83025cc9bb45 100644 > --- a/drivers/hwmon/Makefile > +++ b/drivers/hwmon/Makefile > @@ -46,6 +46,7 @@ obj-$(CONFIG_SENSORS_ADT7475) += adt7475.o > obj-$(CONFIG_SENSORS_APPLESMC) += applesmc.o > obj-$(CONFIG_SENSORS_ARM_SCPI) += scpi-hwmon.o > obj-$(CONFIG_SENSORS_ASC7621) += asc7621.o > +obj-$(CONFIG_SENSORS_ASPEED) += aspeed-pwm-tacho.o > obj-$(CONFIG_SENSORS_ATXP1) += atxp1.o > obj-$(CONFIG_SENSORS_CORETEMP) += coretemp.o > obj-$(CONFIG_SENSORS_DA9052_ADC)+= da9052-hwmon.o > diff --git a/drivers/hwmon/aspeed-pwm-tacho.c b/drivers/hwmon/aspeed-pwm-tacho.c > new file mode 100644 > index 000000000000..28888cc34555 > --- /dev/null > +++ b/drivers/hwmon/aspeed-pwm-tacho.c > @@ -0,0 +1,854 @@ > +/* > + * Copyright (c) 2016 Google, Inc > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 or later as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/clk.h> > +#include <linux/gpio/consumer.h> > +#include <linux/delay.h> > +#include <linux/hwmon.h> > +#include <linux/hwmon-sysfs.h> > +#include <linux/io.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/of_platform.h> > +#include <linux/of_device.h> > +#include <linux/platform_device.h> > +#include <linux/sysfs.h> > +#include <linux/regmap.h> > + > +/* ASPEED PWM & FAN Tach Register Definition */ > +#define ASPEED_PTCR_CTRL 0x00 > +#define ASPEED_PTCR_CLK_CTRL 0x04 > +#define ASPEED_PTCR_DUTY0_CTRL 0x08 > +#define ASPEED_PTCR_DUTY1_CTRL 0x0c > +#define ASPEED_PTCR_TYPEM_CTRL 0x10 > +#define ASPEED_PTCR_TYPEM_CTRL1 0x14 > +#define ASPEED_PTCR_TYPEN_CTRL 0x18 > +#define ASPEED_PTCR_TYPEN_CTRL1 0x1c > +#define ASPEED_PTCR_TACH_SOURCE 0x20 > +#define ASPEED_PTCR_TRIGGER 0x28 > +#define ASPEED_PTCR_RESULT 0x2c > +#define ASPEED_PTCR_INTR_CTRL 0x30 > +#define ASPEED_PTCR_INTR_STS 0x34 > +#define ASPEED_PTCR_TYPEM_LIMIT 0x38 > +#define ASPEED_PTCR_TYPEN_LIMIT 0x3C > +#define ASPEED_PTCR_CTRL_EXT 0x40 > +#define ASPEED_PTCR_CLK_CTRL_EXT 0x44 > +#define ASPEED_PTCR_DUTY2_CTRL 0x48 > +#define ASPEED_PTCR_DUTY3_CTRL 0x4c > +#define ASPEED_PTCR_TYPEO_CTRL 0x50 > +#define ASPEED_PTCR_TYPEO_CTRL1 0x54 > +#define ASPEED_PTCR_TACH_SOURCE_EXT 0x60 > +#define ASPEED_PTCR_TYPEO_LIMIT 0x78 > + > +/* ASPEED_PTCR_CTRL : 0x00 - General Control Register */ > +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART1 15 > +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART2 6 > +#define ASPEED_PTCR_CTRL_SET_PWMD_TYPE_MASK (BIT(7) | BIT(15)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART1 14 > +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART2 5 > +#define ASPEED_PTCR_CTRL_SET_PWMC_TYPE_MASK (BIT(6) | BIT(14)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART1 13 > +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART2 4 > +#define ASPEED_PTCR_CTRL_SET_PWMB_TYPE_MASK (BIT(5) | BIT(13)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART1 12 > +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART2 3 > +#define ASPEED_PTCR_CTRL_SET_PWMA_TYPE_MASK (BIT(4) | BIT(12)) > + > +#define ASPEED_PTCR_CTRL_FAN_NUM_EN(x) BIT(16 + (x)) > + > +#define ASPEED_PTCR_CTRL_PWMD_EN BIT(11) > +#define ASPEED_PTCR_CTRL_PWMC_EN BIT(10) > +#define ASPEED_PTCR_CTRL_PWMB_EN BIT(9) > +#define ASPEED_PTCR_CTRL_PWMA_EN BIT(8) > + > +#define ASPEED_PTCR_CTRL_CLK_SRC BIT(1) > +#define ASPEED_PTCR_CTRL_CLK_EN BIT(0) > + > +/* ASPEED_PTCR_CLK_CTRL : 0x04 - Clock Control Register */ > +/* TYPE N */ > +#define ASPEED_PTCR_CLK_CTRL_TYPEN_MASK GENMASK(31, 16) > +#define ASPEED_PTCR_CLK_CTRL_TYPEN_UNIT 24 > +#define ASPEED_PTCR_CLK_CTRL_TYPEN_H 20 > +#define ASPEED_PTCR_CLK_CTRL_TYPEN_L 16 > +/* TYPE M */ > +#define ASPEED_PTCR_CLK_CTRL_TYPEM_MASK GENMASK(15, 0) > +#define ASPEED_PTCR_CLK_CTRL_TYPEM_UNIT 8 > +#define ASPEED_PTCR_CLK_CTRL_TYPEM_H 4 > +#define ASPEED_PTCR_CLK_CTRL_TYPEM_L 0 > + > +/* > + * ASPEED_PTCR_DUTY_CTRL/1/2/3 : 0x08/0x0C/0x48/0x4C - PWM-FAN duty control > + * 0/1/2/3 register > + */ > +#define DUTY_CTRL_PWM2_FALL_POINT 24 > +#define DUTY_CTRL_PWM2_RISE_POINT 16 > +#define DUTY_CTRL_PWM2_RISE_FALL_MASK GENMASK(31, 16) > +#define DUTY_CTRL_PWM1_FALL_POINT 8 > +#define DUTY_CTRL_PWM1_RISE_POINT 0 > +#define DUTY_CTRL_PWM1_RISE_FALL_MASK GENMASK(15, 0) > + > +/* ASPEED_PTCR_TYPEM_CTRL : 0x10/0x18/0x50 - Type M/N/O Ctrl 0 Register */ > +#define TYPE_CTRL_FAN_MASK (GENMASK(5, 1) | GENMASK(31, 16)) > +#define TYPE_CTRL_FAN1_MASK GENMASK(31, 0) > +#define TYPE_CTRL_FAN_PERIOD 16 > +#define TYPE_CTRL_FAN_MODE 4 > +#define TYPE_CTRL_FAN_DIVISION 1 > +#define TYPE_CTRL_FAN_TYPE_EN 1 > + > +/* ASPEED_PTCR_TACH_SOURCE : 0x20/0x60 - Tach Source Register */ > +/* bit [0,1] at 0x20, bit [2] at 0x60 */ > +#define TACH_PWM_SOURCE_BIT01(x) ((x) * 2) > +#define TACH_PWM_SOURCE_BIT2(x) ((x) * 2) > +#define TACH_PWM_SOURCE_MASK_BIT01(x) (0x3 << ((x) * 2)) > +#define TACH_PWM_SOURCE_MASK_BIT2(x) BIT((x) * 2) > + > +/* ASPEED_PTCR_RESULT : 0x2c - Result Register */ > +#define RESULT_STATUS_MASK BIT(31) > +#define RESULT_VALUE_MASK 0xfffff > + > +/* ASPEED_PTCR_CTRL_EXT : 0x40 - General Control Extension #1 Register */ > +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART1 15 > +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART2 6 > +#define ASPEED_PTCR_CTRL_SET_PWMH_TYPE_MASK (BIT(7) | BIT(15)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART1 14 > +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART2 5 > +#define ASPEED_PTCR_CTRL_SET_PWMG_TYPE_MASK (BIT(6) | BIT(14)) > + > +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART1 13 > +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART2 4 > +#define ASPEED_PTCR_CTRL_SET_PWMF_TYPE_MASK (BIT(5) | BIT(13)) > + > +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART1 12 > +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART2 3 > +#define ASPEED_PTCR_CTRL_SET_PWME_TYPE_MASK (BIT(4) | BIT(12)) > + > +#define ASPEED_PTCR_CTRL_PWMH_EN BIT(11) > +#define ASPEED_PTCR_CTRL_PWMG_EN BIT(10) > +#define ASPEED_PTCR_CTRL_PWMF_EN BIT(9) > +#define ASPEED_PTCR_CTRL_PWME_EN BIT(8) > + > +/* ASPEED_PTCR_CLK_EXT_CTRL : 0x44 - Clock Control Extension #1 Register */ > +/* TYPE O */ > +#define ASPEED_PTCR_CLK_CTRL_TYPEO_MASK GENMASK(15, 0) > +#define ASPEED_PTCR_CLK_CTRL_TYPEO_UNIT 8 > +#define ASPEED_PTCR_CLK_CTRL_TYPEO_H 4 > +#define ASPEED_PTCR_CLK_CTRL_TYPEO_L 0 > + > +#define PWM_MAX 255 > + > +#define M_PWM_DIV_H 0x00 > +#define M_PWM_DIV_L 0x05 > +#define M_PWM_PERIOD 0x5F > +#define M_TACH_CLK_DIV 0x00 > +#define M_TACH_MODE 0x00 > +#define M_TACH_UNIT 0x1000 > +#define INIT_FAN_CTRL 0xFF > + > +struct aspeed_pwm_tacho_regmap { > + void __iomem *regs; > +}; > + Can't you just use the regs pointer directly ? Why a structure with just one variable in it ? > +struct aspeed_pwm_tacho_data { > + struct regmap *regmap; > + unsigned long clk_freq; > + bool pwm_present[8]; > + bool fan_tach_present[16]; > + u8 type_pwm_clock_unit[3]; > + u8 type_pwm_clock_division_h[3]; > + u8 type_pwm_clock_division_l[3]; > + u8 type_fan_tach_clock_division[3]; > + u16 type_fan_tach_unit[3]; > + u8 pwm_port_type[8]; > + u8 pwm_port_fan_ctrl[8]; > + u8 fan_tach_ch_source[16]; > + const struct attribute_group *groups[2]; groups must be NULL terminated, so you'll need three groups here since two are used. > +}; > + > +enum type { TYPEM, TYPEN, TYPEO }; > + > +struct type_params { > + u32 l_value; > + u32 h_value; > + u32 unit_value; > + u32 clk_ctrl_mask; > + u32 clk_ctrl_reg; > + u32 ctrl_reg; > + u32 ctrl_reg1; > +}; > + > +static const struct type_params type_params[] = { > + [TYPEM] = { > + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEM_L, > + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEM_H, > + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEM_UNIT, > + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEM_MASK, > + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL, > + .ctrl_reg = ASPEED_PTCR_TYPEM_CTRL, > + .ctrl_reg1 = ASPEED_PTCR_TYPEM_CTRL1, > + }, > + [TYPEN] = { > + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEN_L, > + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEN_H, > + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEN_UNIT, > + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEN_MASK, > + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL, > + .ctrl_reg = ASPEED_PTCR_TYPEN_CTRL, > + .ctrl_reg1 = ASPEED_PTCR_TYPEN_CTRL1, > + }, > + [TYPEO] = { > + .l_value = ASPEED_PTCR_CLK_CTRL_TYPEO_L, > + .h_value = ASPEED_PTCR_CLK_CTRL_TYPEO_H, > + .unit_value = ASPEED_PTCR_CLK_CTRL_TYPEO_UNIT, > + .clk_ctrl_mask = ASPEED_PTCR_CLK_CTRL_TYPEO_MASK, > + .clk_ctrl_reg = ASPEED_PTCR_CLK_CTRL_EXT, > + .ctrl_reg = ASPEED_PTCR_TYPEO_CTRL, > + .ctrl_reg1 = ASPEED_PTCR_TYPEO_CTRL1, > + } > +}; > + > +enum pwm_port { PWMA, PWMB, PWMC, PWMD, PWME, PWMF, PWMG, PWMH }; > + > +struct pwm_port_params { > + u32 pwm_en; > + u32 ctrl_reg; > + u32 type_part1; > + u32 type_part2; > + u32 type_mask; > + u32 duty_ctrl_rise_point; > + u32 duty_ctrl_fall_point; > + u32 duty_ctrl_reg; > + u32 duty_ctrl_rise_fall_mask; > +}; > + > +static const struct pwm_port_params pwm_port_params[] = { > + [PWMA] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMA_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMA_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY0_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, > + }, > + [PWMB] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMB_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMB_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY0_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, > + }, > + [PWMC] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMC_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMC_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY1_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, > + }, > + [PWMD] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMD_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMD_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY1_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, > + }, > + [PWME] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWME_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWME_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWME_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY2_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, > + }, > + [PWMF] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMF_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMF_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY2_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, > + }, > + [PWMG] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMG_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMG_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM1_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM1_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY3_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM1_RISE_FALL_MASK, > + }, > + [PWMH] = { > + .pwm_en = ASPEED_PTCR_CTRL_PWMH_EN, > + .ctrl_reg = ASPEED_PTCR_CTRL_EXT, > + .type_part1 = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART1, > + .type_part2 = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_PART2, > + .type_mask = ASPEED_PTCR_CTRL_SET_PWMH_TYPE_MASK, > + .duty_ctrl_rise_point = DUTY_CTRL_PWM2_RISE_POINT, > + .duty_ctrl_fall_point = DUTY_CTRL_PWM2_FALL_POINT, > + .duty_ctrl_reg = ASPEED_PTCR_DUTY3_CTRL, > + .duty_ctrl_rise_fall_mask = DUTY_CTRL_PWM2_RISE_FALL_MASK, > + } > +}; > + > +static int regmap_aspeed_pwm_tacho_reg_write(void *context, unsigned int reg, > + unsigned int val) > +{ > + struct aspeed_pwm_tacho_regmap *hregmap = context; > + > + writel(val, hregmap->regs + reg); > + return 0; > +} > + > +static int regmap_aspeed_pwm_tacho_reg_read(void *context, unsigned int reg, > + unsigned int *val) > +{ > + struct aspeed_pwm_tacho_regmap *hregmap = context; > + > + *val = readl(hregmap->regs + reg); > + return 0; > +} > + > +static const struct regmap_config aspeed_pwm_tacho_regmap_config = { > + .reg_bits = 32, > + .val_bits = 32, > + .reg_stride = 4, > + .max_register = ASPEED_PTCR_TYPEO_LIMIT, > + .reg_write = regmap_aspeed_pwm_tacho_reg_write, > + .reg_read = regmap_aspeed_pwm_tacho_reg_read, > + .fast_io = true, > +}; > + > +static void aspeed_set_clock_enable(struct regmap *regmap, bool val) > +{ > + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, > + ASPEED_PTCR_CTRL_CLK_EN, > + val ? ASPEED_PTCR_CTRL_CLK_EN : 0); > +} > + > +static void aspeed_set_clock_source(struct regmap *regmap, int val) > +{ > + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, > + ASPEED_PTCR_CTRL_CLK_SRC, > + val ? ASPEED_PTCR_CTRL_CLK_SRC : 0); > +} > + > +static void aspeed_set_pwm_clock_values(struct regmap *regmap, u8 type, > + u8 div_high, u8 div_low, u8 unit) > +{ > + u32 reg_value = ((div_high << type_params[type].h_value) | > + (div_low << type_params[type].l_value) | > + (unit << type_params[type].unit_value)); > + > + regmap_update_bits(regmap, type_params[type].clk_ctrl_reg, > + type_params[type].clk_ctrl_mask, reg_value); > +} > + > +static void aspeed_set_pwm_port_enable(struct regmap *regmap, u8 pwm_port, > + bool enable) > +{ > + regmap_update_bits(regmap, pwm_port_params[pwm_port].ctrl_reg, > + pwm_port_params[pwm_port].pwm_en, > + enable ? pwm_port_params[pwm_port].pwm_en : 0); > +} > + > +static void aspeed_set_pwm_port_type(struct regmap *regmap, > + u8 pwm_port, u8 type) > +{ > + u32 reg_value = (type & 0x1) << pwm_port_params[pwm_port].type_part1; > + > + reg_value |= (type & 0x2) << pwm_port_params[pwm_port].type_part2; > + > + regmap_update_bits(regmap, pwm_port_params[pwm_port].ctrl_reg, > + pwm_port_params[pwm_port].type_mask, reg_value); > +} > + > +static void aspeed_set_pwm_port_duty_rising_falling(struct regmap *regmap, > + u8 pwm_port, u8 rising, > + u8 falling) > +{ > + u32 reg_value = (rising << > + pwm_port_params[pwm_port].duty_ctrl_rise_point); > + reg_value |= (falling << > + pwm_port_params[pwm_port].duty_ctrl_fall_point); > + > + regmap_update_bits(regmap, pwm_port_params[pwm_port].duty_ctrl_reg, > + pwm_port_params[pwm_port].duty_ctrl_rise_fall_mask, > + reg_value); > +} > + > +static void aspeed_set_tacho_type_enable(struct regmap *regmap, u8 type, > + bool enable) > +{ > + regmap_update_bits(regmap, type_params[type].ctrl_reg, > + TYPE_CTRL_FAN_TYPE_EN, > + enable ? TYPE_CTRL_FAN_TYPE_EN : 0); > +} > + > +static void aspeed_set_tacho_type_values(struct regmap *regmap, u8 type, > + u8 mode, u16 unit, u8 division) > +{ > + u32 reg_value = ((mode << TYPE_CTRL_FAN_MODE) | > + (unit << TYPE_CTRL_FAN_PERIOD) | > + (division << TYPE_CTRL_FAN_DIVISION)); > + > + regmap_update_bits(regmap, type_params[type].ctrl_reg, > + TYPE_CTRL_FAN_MASK, reg_value); > + regmap_update_bits(regmap, type_params[type].ctrl_reg1, > + TYPE_CTRL_FAN1_MASK, unit << 16); > +} > + > +static void aspeed_set_fan_tach_ch_enable(struct regmap *regmap, u8 fan_tach_ch, > + bool enable) > +{ > + regmap_update_bits(regmap, ASPEED_PTCR_CTRL, > + ASPEED_PTCR_CTRL_FAN_NUM_EN(fan_tach_ch), > + enable ? > + ASPEED_PTCR_CTRL_FAN_NUM_EN(fan_tach_ch) : 0); > +} > + > +static void aspeed_set_fan_tach_ch_source(struct regmap *regmap, u8 fan_tach_ch, > + u8 fan_tach_ch_source) > +{ > + u32 reg_value1 = ((fan_tach_ch_source & 0x3) << > + TACH_PWM_SOURCE_BIT01(fan_tach_ch)); > + u32 reg_value2 = (((fan_tach_ch_source & 0x4) >> 2) << > + TACH_PWM_SOURCE_BIT2(fan_tach_ch)); > + > + regmap_update_bits(regmap, ASPEED_PTCR_TACH_SOURCE, > + TACH_PWM_SOURCE_MASK_BIT01(fan_tach_ch), > + reg_value1); > + > + regmap_update_bits(regmap, ASPEED_PTCR_TACH_SOURCE_EXT, > + TACH_PWM_SOURCE_MASK_BIT2(fan_tach_ch), > + reg_value2); > +} > + > +static void aspeed_set_pwm_port_fan_ctrl(struct aspeed_pwm_tacho_data *priv, > + u8 index, u8 fan_ctrl) > +{ > + u16 period, dc_time_on; > + > + period = priv->type_pwm_clock_unit[priv->pwm_port_type[index]]; > + period += 1; > + dc_time_on = (fan_ctrl * period) / PWM_MAX; > + > + if (dc_time_on == 0) { > + aspeed_set_pwm_port_enable(priv->regmap, index, false); > + } else { > + if (dc_time_on == period) > + dc_time_on = 0; > + > + aspeed_set_pwm_port_duty_rising_falling(priv->regmap, index, 0, > + dc_time_on); > + aspeed_set_pwm_port_enable(priv->regmap, index, true); > + } > +} > + > +static u32 aspeed_get_fan_tach_ch_measure_period(struct aspeed_pwm_tacho_data > + *priv, u8 type) > +{ > + u32 clk; > + u16 tacho_unit; > + u8 clk_unit, div_h, div_l, tacho_div; > + > + clk = priv->clk_freq; > + clk_unit = priv->type_pwm_clock_unit[type]; > + div_h = priv->type_pwm_clock_division_h[type]; > + div_h = 0x1 << div_h; > + div_l = priv->type_pwm_clock_division_l[type]; > + if (div_l == 0) > + div_l = 1; > + else > + div_l = div_l * 2; > + > + tacho_unit = priv->type_fan_tach_unit[type]; > + tacho_div = priv->type_fan_tach_clock_division[type]; > + > + tacho_div = 0x4 << (tacho_div * 2); > + return clk / (clk_unit * div_h * div_l * tacho_div * tacho_unit); > +} > + > +static u32 aspeed_get_fan_tach_ch_rpm(struct aspeed_pwm_tacho_data *priv, > + u8 fan_tach_ch) > +{ > + u32 raw_data, tach_div, clk_source, timeout = 0, sec, val; > + u8 fan_tach_ch_source, type; > + > + regmap_write(priv->regmap, ASPEED_PTCR_TRIGGER, 0); > + regmap_write(priv->regmap, ASPEED_PTCR_TRIGGER, 0x1 << fan_tach_ch); > + > + fan_tach_ch_source = priv->fan_tach_ch_source[fan_tach_ch]; > + type = priv->pwm_port_type[fan_tach_ch_source]; > + > + sec = (1000 / aspeed_get_fan_tach_ch_measure_period(priv, type)); > + > + msleep(sec); > + > + regmap_read(priv->regmap, ASPEED_PTCR_RESULT, &val); > + while (!(val & RESULT_STATUS_MASK)) { > + timeout++; > + if (timeout > 1) > + return 0; > + msleep(sec); val never changes. > + } > + > + regmap_read(priv->regmap, ASPEED_PTCR_RESULT, &val); > + raw_data = val & RESULT_VALUE_MASK; > + tach_div = priv->type_fan_tach_clock_division[type]; > + > + tach_div = 0x4 << (tach_div * 2); > + clk_source = priv->clk_freq; > + > + if (raw_data == 0) > + return 0; > + else else is unnecessary after return > + return (clk_source * 60) / (2 * raw_data * tach_div); > +} > + > +static ssize_t set_pwm(struct device *dev, struct device_attribute *attr, > + const char *buf, size_t count) > +{ > + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); > + int index = sensor_attr->index; > + int ret; > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + long fan_ctrl; > + > + ret = kstrtol(buf, 10, &fan_ctrl); > + if (ret != 0) > + return ret; > + > + if (fan_ctrl < 0 || fan_ctrl > PWM_MAX) > + return -EINVAL; > + > + if (priv->pwm_port_fan_ctrl[index] == fan_ctrl) > + return count; > + > + priv->pwm_port_fan_ctrl[index] = fan_ctrl; > + aspeed_set_pwm_port_fan_ctrl(priv, index, fan_ctrl); > + > + return count; > +} > + > +static ssize_t show_pwm(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); > + int index = sensor_attr->index; > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + > + return sprintf(buf, "%u\n", priv->pwm_port_fan_ctrl[index]); > +} > + > +static ssize_t show_rpm(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); > + int index = sensor_attr->index; > + u32 rpm; > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + > + rpm = aspeed_get_fan_tach_ch_rpm(priv, index); > + > + return sprintf(buf, "%u\n", rpm); > +} > + > +static umode_t pwm_is_visible(struct kobject *kobj, > + struct attribute *a, int index) > +{ > + struct device *dev = container_of(kobj, struct device, kobj); > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + > + if (!priv->pwm_present[index]) > + return 0; > + return a->mode; > +} > + > +static umode_t fan_dev_is_visible(struct kobject *kobj, > + struct attribute *a, int index) > +{ > + struct device *dev = container_of(kobj, struct device, kobj); > + struct aspeed_pwm_tacho_data *priv = dev_get_drvdata(dev); > + > + if (!priv->fan_tach_present[index]) > + return 0; > + return a->mode; > +} > + > +static SENSOR_DEVICE_ATTR(pwm0, 0644, > + show_pwm, set_pwm, 0); > +static SENSOR_DEVICE_ATTR(pwm1, 0644, > + show_pwm, set_pwm, 1); > +static SENSOR_DEVICE_ATTR(pwm2, 0644, > + show_pwm, set_pwm, 2); > +static SENSOR_DEVICE_ATTR(pwm3, 0644, > + show_pwm, set_pwm, 3); > +static SENSOR_DEVICE_ATTR(pwm4, 0644, > + show_pwm, set_pwm, 4); > +static SENSOR_DEVICE_ATTR(pwm5, 0644, > + show_pwm, set_pwm, 5); > +static SENSOR_DEVICE_ATTR(pwm6, 0644, > + show_pwm, set_pwm, 6); > +static SENSOR_DEVICE_ATTR(pwm7, 0644, > + show_pwm, set_pwm, 7); Unnecessary continuation lines. > + > +static struct attribute *pwm_dev_attrs[] = { > + &sensor_dev_attr_pwm0.dev_attr.attr, > + &sensor_dev_attr_pwm1.dev_attr.attr, > + &sensor_dev_attr_pwm2.dev_attr.attr, > + &sensor_dev_attr_pwm3.dev_attr.attr, > + &sensor_dev_attr_pwm4.dev_attr.attr, > + &sensor_dev_attr_pwm5.dev_attr.attr, > + &sensor_dev_attr_pwm6.dev_attr.attr, > + &sensor_dev_attr_pwm7.dev_attr.attr, > + NULL, > +}; > + > +static const struct attribute_group pwm_dev_group = { > + .attrs = pwm_dev_attrs, > + .is_visible = pwm_is_visible, > +}; > + > +static SENSOR_DEVICE_ATTR(fan0_input, 0444, > + show_rpm, NULL, 0); > +static SENSOR_DEVICE_ATTR(fan1_input, 0444, > + show_rpm, NULL, 1); > +static SENSOR_DEVICE_ATTR(fan2_input, 0444, > + show_rpm, NULL, 2); > +static SENSOR_DEVICE_ATTR(fan3_input, 0444, > + show_rpm, NULL, 3); > +static SENSOR_DEVICE_ATTR(fan4_input, 0444, > + show_rpm, NULL, 4); > +static SENSOR_DEVICE_ATTR(fan5_input, 0444, > + show_rpm, NULL, 5); > +static SENSOR_DEVICE_ATTR(fan6_input, 0444, > + show_rpm, NULL, 6); > +static SENSOR_DEVICE_ATTR(fan7_input, 0444, > + show_rpm, NULL, 7); > +static SENSOR_DEVICE_ATTR(fan8_input, 0444, > + show_rpm, NULL, 8); > +static SENSOR_DEVICE_ATTR(fan9_input, 0444, > + show_rpm, NULL, 9); > +static SENSOR_DEVICE_ATTR(fan10_input, 0444, > + show_rpm, NULL, 10); > +static SENSOR_DEVICE_ATTR(fan11_input, 0444, > + show_rpm, NULL, 11); > +static SENSOR_DEVICE_ATTR(fan12_input, 0444, > + show_rpm, NULL, 12); > +static SENSOR_DEVICE_ATTR(fan13_input, 0444, > + show_rpm, NULL, 13); > +static SENSOR_DEVICE_ATTR(fan14_input, 0444, > + show_rpm, NULL, 14); > +static SENSOR_DEVICE_ATTR(fan15_input, 0444, > + show_rpm, NULL, 15); > + Unnecessary continuation lines. > +static struct attribute *fan_dev_attrs[] = { > + &sensor_dev_attr_fan0_input.dev_attr.attr, > + &sensor_dev_attr_fan1_input.dev_attr.attr, > + &sensor_dev_attr_fan2_input.dev_attr.attr, > + &sensor_dev_attr_fan3_input.dev_attr.attr, > + &sensor_dev_attr_fan4_input.dev_attr.attr, > + &sensor_dev_attr_fan5_input.dev_attr.attr, > + &sensor_dev_attr_fan6_input.dev_attr.attr, > + &sensor_dev_attr_fan7_input.dev_attr.attr, > + &sensor_dev_attr_fan8_input.dev_attr.attr, > + &sensor_dev_attr_fan9_input.dev_attr.attr, > + &sensor_dev_attr_fan10_input.dev_attr.attr, > + &sensor_dev_attr_fan11_input.dev_attr.attr, > + &sensor_dev_attr_fan12_input.dev_attr.attr, > + &sensor_dev_attr_fan13_input.dev_attr.attr, > + &sensor_dev_attr_fan14_input.dev_attr.attr, > + &sensor_dev_attr_fan15_input.dev_attr.attr, > + NULL > +}; > + > +static const struct attribute_group fan_dev_group = { > + .attrs = fan_dev_attrs, > + .is_visible = fan_dev_is_visible, > +}; > + > +/* > + * The clock type is type M : > + * The PWM frequency = 24MHz / (type M clock division L bit * > + * type M clock division H bit * (type M PWM period bit + 1)) > + */ > +static void aspeed_create_type(struct aspeed_pwm_tacho_data *priv) > +{ > + priv->type_pwm_clock_division_h[TYPEM] = M_PWM_DIV_H; > + priv->type_pwm_clock_division_l[TYPEM] = M_PWM_DIV_L; > + priv->type_pwm_clock_unit[TYPEM] = M_PWM_PERIOD; > + aspeed_set_pwm_clock_values(priv->regmap, TYPEM, M_PWM_DIV_H, > + M_PWM_DIV_L, M_PWM_PERIOD); > + aspeed_set_tacho_type_enable(priv->regmap, TYPEM, true); > + priv->type_fan_tach_clock_division[TYPEM] = M_TACH_CLK_DIV; > + priv->type_fan_tach_unit[TYPEM] = M_TACH_UNIT; > + aspeed_set_tacho_type_values(priv->regmap, TYPEM, M_TACH_MODE, > + M_TACH_UNIT, M_TACH_CLK_DIV); > +} > + > +static void aspeed_create_pwm_port(struct aspeed_pwm_tacho_data *priv, > + u8 pwm_port) > +{ > + aspeed_set_pwm_port_enable(priv->regmap, pwm_port, true); > + priv->pwm_present[pwm_port] = true; > + > + priv->pwm_port_type[pwm_port] = TYPEM; > + aspeed_set_pwm_port_type(priv->regmap, pwm_port, TYPEM); > + > + priv->pwm_port_fan_ctrl[pwm_port] = INIT_FAN_CTRL; > + aspeed_set_pwm_port_fan_ctrl(priv, pwm_port, INIT_FAN_CTRL); > +} > + > +static void aspeed_create_fan_tach_channel(struct aspeed_pwm_tacho_data *priv, > + u8 *fan_tach_ch, > + int count, > + u8 pwm_source) > +{ > + u8 val, index; > + > + for (val = 0; val < count; val++) { > + index = fan_tach_ch[val]; > + aspeed_set_fan_tach_ch_enable(priv->regmap, index, true); > + priv->fan_tach_present[index] = true; > + priv->fan_tach_ch_source[index] = pwm_source; > + aspeed_set_fan_tach_ch_source(priv->regmap, index, pwm_source); > + } > +} > + > +static int aspeed_create_fan(struct device *dev, > + struct device_node *child, > + struct aspeed_pwm_tacho_data *priv) > +{ > + u8 *fan_tach_ch; > + u32 pwm_port; > + int ret, count; > + > + ret = of_property_read_u32(child, "reg", &pwm_port); > + if (ret) > + return ret; > + aspeed_create_pwm_port(priv, (u8)pwm_port); > + > + count = of_property_count_u8_elems(child, "aspeed-fan-tach-ch"); > + if (count < 1) > + return -EINVAL; > + fan_tach_ch = devm_kzalloc(dev, sizeof(*fan_tach_ch) * count, > + GFP_KERNEL); > + if (!fan_tach_ch) > + return -ENOMEM; > + ret = of_property_read_u8_array(child, "aspeed-fan-tach-ch", > + fan_tach_ch, count); > + if (ret) > + return ret; > + aspeed_create_fan_tach_channel(priv, fan_tach_ch, count, pwm_port); > + > + return 0; > +} > + > +static int aspeed_pwm_tacho_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct device_node *np, *child; > + struct aspeed_pwm_tacho_data *priv; > + struct aspeed_pwm_tacho_regmap *hregmap; > + struct resource *res; > + struct device *hwmon; > + struct clk *clk; > + int ret; > + > + np = dev->of_node; > + > + hregmap = devm_kzalloc(dev, sizeof(*hregmap), GFP_KERNEL); > + if (!hregmap) > + return -ENOMEM; > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + if (!res) > + return -ENOENT; > + hregmap->regs = devm_ioremap_resource(dev, res); > + if (IS_ERR(hregmap->regs)) > + return PTR_ERR(hregmap->regs); > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); > + if (!priv) > + return -ENOMEM; > + priv->regmap = devm_regmap_init(dev, NULL, hregmap, > + &aspeed_pwm_tacho_regmap_config); > + if (IS_ERR(priv->regmap)) > + return PTR_ERR(priv->regmap); > + regmap_write(priv->regmap, ASPEED_PTCR_TACH_SOURCE, 0); > + regmap_write(priv->regmap, ASPEED_PTCR_TACH_SOURCE_EXT, 0); > + > + clk = devm_clk_get(dev, NULL); > + if (IS_ERR(clk)) > + return -ENODEV; > + priv->clk_freq = clk_get_rate(clk); > + aspeed_set_clock_enable(priv->regmap, true); > + aspeed_set_clock_source(priv->regmap, 0); > + > + aspeed_create_type(priv); > + > + for_each_child_of_node(np, child) { > + ret = aspeed_create_fan(dev, child, priv); > + of_node_put(child); > + if (ret) > + return ret; > + } > + of_node_put(np); > + > + priv->groups[0] = &pwm_dev_group; > + priv->groups[1] = &fan_dev_group; > + hwmon = devm_hwmon_device_register_with_groups(dev, > + "aspeed_pwm_tacho", > + priv, priv->groups); > + > + return PTR_ERR_OR_ZERO(hwmon); > +} > + > +static const struct of_device_id of_pwm_tacho_match_table[] = { > + { .compatible = "aspeed,ast2400-pwm-tacho", }, > + { .compatible = "aspeed,ast2500-pwm-tacho", }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, of_pwm_tacho_match_table); > + > +static struct platform_driver aspeed_pwm_tacho_driver = { > + .probe = aspeed_pwm_tacho_probe, > + .driver = { > + .name = "aspeed_pwm_tacho", > + .of_match_table = of_pwm_tacho_match_table, > + }, > +}; > + > +module_platform_driver(aspeed_pwm_tacho_driver); > + > +MODULE_AUTHOR("Jaghathiswari Rankappagounder Natarajan <jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>"); > +MODULE_DESCRIPTION("ASPEED PWM and Fan Tacho device driver"); > +MODULE_LICENSE("GPL"); > -- > 2.12.1.578.ge9c3154ca4-goog > > -- > To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in > the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2017-04-01 22:45 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2017-03-24 18:17 [PATCH linux v5 0/2] Support for ASPEED AST2400/AST2500 PWM and Fan Tach driver Jaghathiswari Rankappagounder Natarajan
[not found] ` <20170324181723.29379-1-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>
2017-03-24 18:17 ` [PATCH linux v5 1/2] Documentation: dt-bindings: Document bindings for ASPEED AST2400/AST2500 PWM and Fan tach controller device driver Jaghathiswari Rankappagounder Natarajan
2017-03-29 22:14 ` Jaghathiswari Rankappagounder Natarajan
2017-03-30 22:46 ` Rob Herring
2017-03-24 18:17 ` [PATCH linux v5 2/2] drivers: hwmon: Support for ASPEED PWM/Fan tach Jaghathiswari Rankappagounder Natarajan
2017-03-29 22:15 ` Jaghathiswari Rankappagounder Natarajan
[not found] ` <20170324181723.29379-3-jaghu-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>
2017-04-01 22:45 ` Guenter Roeck
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).