[PATCH RESEND 1/4] dt-bindings: mtd: make partitions doc a bit more generic

["Rafał Miłecki" <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>]

From: Brian Norris <computersforpeace-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Currently the only documented partitioning is "fixed-partitions" but
there are more methods in use that we may want to support in the future.
Mention them and make it clear Fixed Partitions are just a single case.

Signed-off-by: Brian Norris <computersforpeace-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
---
 .../devicetree/bindings/mtd/partition.txt          | 28 +++++++++++++++++-----
 1 file changed, 22 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt
index 81a224da63be..27593adc45c2 100644
--- a/Documentation/devicetree/bindings/mtd/partition.txt
+++ b/Documentation/devicetree/bindings/mtd/partition.txt
@@ -1,29 +1,45 @@
-Representing flash partitions in devicetree
+Flash partitions in device tree
+===============================
 
-Partitions can be represented by sub-nodes of an mtd device. This can be used
+Flash devices can be partitioned into one or more functional ranges (e.g. "boot
+code", "nvram", "kernel").
+
+Different devices may be partitioned in a different ways. Some may use a fixed
+flash layout set at production time. Some may use on-flash table that describes
+the geometry and naming/purpose of each functional region. It is also possible
+to see these methods mixed.
+
+To assist system software in locating partitions, we provide a binding to
+describe which method is used for a given flash.
+
+
+Fixed Partitions
+================
+
+Partitions can be represented by sub-nodes of a flash device. This can be used
 on platforms which have strong conventions about which portions of a flash are
 used for what purposes, but which don't use an on-flash partition table such
 as RedBoot.
 
-The partition table should be a subnode of the mtd node and should be named
+The partition table should be a subnode of the flash node and should be named
 'partitions'. This node should have the following property:
 - compatible : (required) must be "fixed-partitions"
 Partitions are then defined in subnodes of the partitions node.
 
-For backwards compatibility partitions as direct subnodes of the mtd device are
+For backwards compatibility partitions as direct subnodes of the flash device are
 supported. This use is discouraged.
 NOTE: also for backwards compatibility, direct subnodes that have a compatible
 string are not considered partitions, as they may be used for other bindings.
 
 #address-cells & #size-cells must both be present in the partitions subnode of the
-mtd device. There are two valid values for both:
+flash device. There are two valid values for both:
 <1>: for partitions that require a single 32-bit cell to represent their
      size/address (aka the value is below 4 GiB)
 <2>: for partitions that require two 32-bit cells to represent their
      size/address (aka the value is 4 GiB or greater).
 
 Required properties:
-- reg : The partition's offset and size within the mtd bank.
+- reg : The partition's offset and size within the flash
 
 Optional properties:
 - label : The label / name for this partition.  If omitted, the label is taken
-- 
2.11.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html