[PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Tony Lindgren]

This is needed in preparation of adding support for omap3 and
later OHCI. The runtime PM will only do something on platforms
that implement it.

Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Cc: Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org>
Cc: Sebastian Reichel <sebastian.reichel-ZGY8ohtN/8pPYcu2f3hruQ@public.gmane.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
---

Alan, do you have some better ideas for the ohci_platform_remove()
path below?

---
 drivers/usb/host/ohci-platform.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/ohci-platform.c b/drivers/usb/host/ohci-platform.c
--- a/drivers/usb/host/ohci-platform.c
+++ b/drivers/usb/host/ohci-platform.c
@@ -24,6 +24,7 @@
 #include <linux/err.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/reset.h>
 #include <linux/usb/ohci_pdriver.h>
 #include <linux/usb.h>
@@ -242,6 +243,8 @@ static int ohci_platform_probe(struct platform_device *dev)
 	}
 #endif
 
+	pm_runtime_set_active(&dev->dev);
+	pm_runtime_enable(&dev->dev);
 	if (pdata->power_on) {
 		err = pdata->power_on(dev);
 		if (err < 0)
@@ -271,6 +274,7 @@ static int ohci_platform_probe(struct platform_device *dev)
 	if (pdata->power_off)
 		pdata->power_off(dev);
 err_reset:
+	pm_runtime_disable(&dev->dev);
 	while (--rst >= 0)
 		reset_control_assert(priv->resets[rst]);
 err_put_clks:
@@ -290,7 +294,14 @@ static int ohci_platform_remove(struct platform_device *dev)
 	struct usb_hcd *hcd = platform_get_drvdata(dev);
 	struct usb_ohci_pdata *pdata = dev_get_platdata(&dev->dev);
 	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
-	int clk, rst;
+	int clk, rst, enabled;
+
+	enabled = pm_runtime_get_sync(&dev->dev);
+	if (enabled < 0) {
+		dev_warn(&dev->dev, "pm_runtime_get failed: %i\n",
+			 enabled);
+		pm_runtime_put_noidle(&dev->dev);
+	}
 
 	usb_remove_hcd(hcd);
 
@@ -305,6 +316,10 @@ static int ohci_platform_remove(struct platform_device *dev)
 
 	usb_put_hcd(hcd);
 
+	if (enabled >= 0)
+		pm_runtime_put_sync(&dev->dev);
+	pm_runtime_disable(&dev->dev);
+
 	if (pdata == &ohci_platform_defaults)
 		dev->dev.platform_data = NULL;
 
-- 
2.13.0
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Roger Quadros]

Hi,

On 22/05/17 19:00, Tony Lindgren wrote:
> This is needed in preparation of adding support for omap3 and
> later OHCI. The runtime PM will only do something on platforms
> that implement it.
> 
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Cc: Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org>
> Cc: Sebastian Reichel <sebastian.reichel-ZGY8ohtN/8pPYcu2f3hruQ@public.gmane.org>
> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
> Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
> ---
> 
> Alan, do you have some better ideas for the ohci_platform_remove()
> path below?
> 
> ---
>  drivers/usb/host/ohci-platform.c | 17 ++++++++++++++++-
>  1 file changed, 16 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/usb/host/ohci-platform.c b/drivers/usb/host/ohci-platform.c
> --- a/drivers/usb/host/ohci-platform.c
> +++ b/drivers/usb/host/ohci-platform.c
> @@ -24,6 +24,7 @@
>  #include <linux/err.h>
>  #include <linux/phy/phy.h>
>  #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
>  #include <linux/reset.h>
>  #include <linux/usb/ohci_pdriver.h>
>  #include <linux/usb.h>
> @@ -242,6 +243,8 @@ static int ohci_platform_probe(struct platform_device *dev)
>  	}
>  #endif
>  
> +	pm_runtime_set_active(&dev->dev);
> +	pm_runtime_enable(&dev->dev);
>  	if (pdata->power_on) {
>  		err = pdata->power_on(dev);
>  		if (err < 0)
> @@ -271,6 +274,7 @@ static int ohci_platform_probe(struct platform_device *dev)
>  	if (pdata->power_off)
>  		pdata->power_off(dev);
>  err_reset:
> +	pm_runtime_disable(&dev->dev);
>  	while (--rst >= 0)
>  		reset_control_assert(priv->resets[rst]);
>  err_put_clks:
> @@ -290,7 +294,14 @@ static int ohci_platform_remove(struct platform_device *dev)
>  	struct usb_hcd *hcd = platform_get_drvdata(dev);
>  	struct usb_ohci_pdata *pdata = dev_get_platdata(&dev->dev);
>  	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
> -	int clk, rst;
> +	int clk, rst, enabled;
> +
> +	enabled = pm_runtime_get_sync(&dev->dev);

Why do we need to pm_runtime_get_sync() here?

> +	if (enabled < 0) {
> +		dev_warn(&dev->dev, "pm_runtime_get failed: %i\n",
> +			 enabled);
> +		pm_runtime_put_noidle(&dev->dev);
> +	}
>  
>  	usb_remove_hcd(hcd);
>  
> @@ -305,6 +316,10 @@ static int ohci_platform_remove(struct platform_device *dev)
>  
>  	usb_put_hcd(hcd);
>  
> +	if (enabled >= 0)
> +		pm_runtime_put_sync(&dev->dev);
> +	pm_runtime_disable(&dev->dev);
> +
>  	if (pdata == &ohci_platform_defaults)
>  		dev->dev.platform_data = NULL;
>  
> 

-- 
cheers,
-roger
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Tony Lindgren]

* Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org> [170523 00:14]:
> On 22/05/17 19:00, Tony Lindgren wrote:
> > --- a/drivers/usb/host/ohci-platform.c
> > +++ b/drivers/usb/host/ohci-platform.c
> > @@ -290,7 +294,14 @@ static int ohci_platform_remove(struct platform_device *dev)
> >  	struct usb_hcd *hcd = platform_get_drvdata(dev);
> >  	struct usb_ohci_pdata *pdata = dev_get_platdata(&dev->dev);
> >  	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
> > -	int clk, rst;
> > +	int clk, rst, enabled;
> > +
> > +	enabled = pm_runtime_get_sync(&dev->dev);
> 
> Why do we need to pm_runtime_get_sync() here?

ohci_platform_remove()
	usb_remove_hcd()
		ohci_stop()

Will cause "external abort on non-linefetch" otherwise.

Regards,

Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Roger Quadros]

On 23/05/17 17:08, Tony Lindgren wrote:
> * Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org> [170523 00:14]:
>> On 22/05/17 19:00, Tony Lindgren wrote:
>>> --- a/drivers/usb/host/ohci-platform.c
>>> +++ b/drivers/usb/host/ohci-platform.c
>>> @@ -290,7 +294,14 @@ static int ohci_platform_remove(struct platform_device *dev)
>>>  	struct usb_hcd *hcd = platform_get_drvdata(dev);
>>>  	struct usb_ohci_pdata *pdata = dev_get_platdata(&dev->dev);
>>>  	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
>>> -	int clk, rst;
>>> +	int clk, rst, enabled;
>>> +
>>> +	enabled = pm_runtime_get_sync(&dev->dev);
>>
>> Why do we need to pm_runtime_get_sync() here?
> 
> ohci_platform_remove()
> 	usb_remove_hcd()
> 		ohci_stop()
> 
> Will cause "external abort on non-linefetch" otherwise.

Got it, thanks.

> 
> Regards,
> 
> Tony
> --
> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 

-- 
cheers,
-roger
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Alan Stern]

On Mon, 22 May 2017, Tony Lindgren wrote:

> This is needed in preparation of adding support for omap3 and
> later OHCI. The runtime PM will only do something on platforms
> that implement it.
> 
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Cc: Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org>
> Cc: Sebastian Reichel <sebastian.reichel-ZGY8ohtN/8pPYcu2f3hruQ@public.gmane.org>
> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
> Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
> ---
> 
> Alan, do you have some better ideas for the ohci_platform_remove()
> path below?
> 
> ---
>  drivers/usb/host/ohci-platform.c | 17 ++++++++++++++++-
>  1 file changed, 16 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/usb/host/ohci-platform.c b/drivers/usb/host/ohci-platform.c
> --- a/drivers/usb/host/ohci-platform.c
> +++ b/drivers/usb/host/ohci-platform.c
> @@ -24,6 +24,7 @@
>  #include <linux/err.h>
>  #include <linux/phy/phy.h>
>  #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
>  #include <linux/reset.h>
>  #include <linux/usb/ohci_pdriver.h>
>  #include <linux/usb.h>
> @@ -242,6 +243,8 @@ static int ohci_platform_probe(struct platform_device *dev)
>  	}
>  #endif
>  
> +	pm_runtime_set_active(&dev->dev);
> +	pm_runtime_enable(&dev->dev);
>  	if (pdata->power_on) {
>  		err = pdata->power_on(dev);
>  		if (err < 0)
> @@ -271,6 +274,7 @@ static int ohci_platform_probe(struct platform_device *dev)
>  	if (pdata->power_off)
>  		pdata->power_off(dev);
>  err_reset:
> +	pm_runtime_disable(&dev->dev);
>  	while (--rst >= 0)
>  		reset_control_assert(priv->resets[rst]);
>  err_put_clks:
> @@ -290,7 +294,14 @@ static int ohci_platform_remove(struct platform_device *dev)
>  	struct usb_hcd *hcd = platform_get_drvdata(dev);
>  	struct usb_ohci_pdata *pdata = dev_get_platdata(&dev->dev);
>  	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
> -	int clk, rst;
> +	int clk, rst, enabled;
> +
> +	enabled = pm_runtime_get_sync(&dev->dev);
> +	if (enabled < 0) {
> +		dev_warn(&dev->dev, "pm_runtime_get failed: %i\n",
> +			 enabled);
> +		pm_runtime_put_noidle(&dev->dev);
> +	}

I wouldn't worry about checking the return value.  There's no 
particular reason for this call to fail, is there?

>  
>  	usb_remove_hcd(hcd);
>  
> @@ -305,6 +316,10 @@ static int ohci_platform_remove(struct platform_device *dev)
>  
>  	usb_put_hcd(hcd);
>  
> +	if (enabled >= 0)
> +		pm_runtime_put_sync(&dev->dev);
> +	pm_runtime_disable(&dev->dev);

And here you could just do the put_sync, with no test.  If the get_sync
failed then this will probably fail too, but you won't be any worse off
for the attempt.

Alan Stern

> +
>  	if (pdata == &ohci_platform_defaults)
>  		dev->dev.platform_data = NULL;

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Tony Lindgren]

* Alan Stern <stern-nwvwT67g6+6dFdvTe/nMLpVzexx5G7lz@public.gmane.org> [170523 09:57]:
> On Mon, 22 May 2017, Tony Lindgren wrote:
> > Alan, do you have some better ideas for the ohci_platform_remove()
> > path below?
...
> > --- a/drivers/usb/host/ohci-platform.c
> > +++ b/drivers/usb/host/ohci-platform.c
> > @@ -290,7 +294,14 @@ static int ohci_platform_remove(struct platform_device *dev)
> >  	struct usb_hcd *hcd = platform_get_drvdata(dev);
> >  	struct usb_ohci_pdata *pdata = dev_get_platdata(&dev->dev);
> >  	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
> > -	int clk, rst;
> > +	int clk, rst, enabled;
> > +
> > +	enabled = pm_runtime_get_sync(&dev->dev);
> > +	if (enabled < 0) {
> > +		dev_warn(&dev->dev, "pm_runtime_get failed: %i\n",
> > +			 enabled);
> > +		pm_runtime_put_noidle(&dev->dev);
> > +	}
> 
> I wouldn't worry about checking the return value.  There's no 
> particular reason for this call to fail, is there?

OK yeah if it was to fail it would already fail on probe
already :)

> >  	usb_remove_hcd(hcd);
> >  
> > @@ -305,6 +316,10 @@ static int ohci_platform_remove(struct platform_device *dev)
> >  
> >  	usb_put_hcd(hcd);
> >  
> > +	if (enabled >= 0)
> > +		pm_runtime_put_sync(&dev->dev);
> > +	pm_runtime_disable(&dev->dev);
> 
> And here you could just do the put_sync, with no test.  If the get_sync
> failed then this will probably fail too, but you won't be any worse off
> for the attempt.

OK fine with me.

Thanks,

Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Tony Lindgren]

This is needed in preparation of adding support for omap3 and
later OHCI. The runtime PM will only do something on platforms
that implement it.

Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Cc: Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org>
Cc: Sebastian Reichel <sebastian.reichel-ZGY8ohtN/8pPYcu2f3hruQ@public.gmane.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
---
 drivers/usb/host/ohci-platform.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/usb/host/ohci-platform.c b/drivers/usb/host/ohci-platform.c
--- a/drivers/usb/host/ohci-platform.c
+++ b/drivers/usb/host/ohci-platform.c
@@ -24,6 +24,7 @@
 #include <linux/err.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/reset.h>
 #include <linux/usb/ohci_pdriver.h>
 #include <linux/usb.h>
@@ -242,6 +243,8 @@ static int ohci_platform_probe(struct platform_device *dev)
 	}
 #endif
 
+	pm_runtime_set_active(&dev->dev);
+	pm_runtime_enable(&dev->dev);
 	if (pdata->power_on) {
 		err = pdata->power_on(dev);
 		if (err < 0)
@@ -271,6 +274,7 @@ static int ohci_platform_probe(struct platform_device *dev)
 	if (pdata->power_off)
 		pdata->power_off(dev);
 err_reset:
+	pm_runtime_disable(&dev->dev);
 	while (--rst >= 0)
 		reset_control_assert(priv->resets[rst]);
 err_put_clks:
@@ -292,6 +296,7 @@ static int ohci_platform_remove(struct platform_device *dev)
 	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
 	int clk, rst;
 
+	pm_runtime_get_sync(&dev->dev);
 	usb_remove_hcd(hcd);
 
 	if (pdata->power_off)
@@ -305,6 +310,9 @@ static int ohci_platform_remove(struct platform_device *dev)
 
 	usb_put_hcd(hcd);
 
+	pm_runtime_put_sync(&dev->dev);
+	pm_runtime_disable(&dev->dev);
+
 	if (pdata == &ohci_platform_defaults)
 		dev->dev.platform_data = NULL;
 
-- 
2.13.0
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Alan Stern]

On Thu, 25 May 2017, Tony Lindgren wrote:

> This is needed in preparation of adding support for omap3 and
> later OHCI. The runtime PM will only do something on platforms
> that implement it.
> 
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Cc: Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org>
> Cc: Sebastian Reichel <sebastian.reichel-ZGY8ohtN/8pPYcu2f3hruQ@public.gmane.org>
> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
> Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
> ---
>  drivers/usb/host/ohci-platform.c | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/drivers/usb/host/ohci-platform.c b/drivers/usb/host/ohci-platform.c
> --- a/drivers/usb/host/ohci-platform.c
> +++ b/drivers/usb/host/ohci-platform.c
> @@ -24,6 +24,7 @@
>  #include <linux/err.h>
>  #include <linux/phy/phy.h>
>  #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
>  #include <linux/reset.h>
>  #include <linux/usb/ohci_pdriver.h>
>  #include <linux/usb.h>
> @@ -242,6 +243,8 @@ static int ohci_platform_probe(struct platform_device *dev)
>  	}
>  #endif
>  
> +	pm_runtime_set_active(&dev->dev);
> +	pm_runtime_enable(&dev->dev);
>  	if (pdata->power_on) {
>  		err = pdata->power_on(dev);
>  		if (err < 0)
> @@ -271,6 +274,7 @@ static int ohci_platform_probe(struct platform_device *dev)
>  	if (pdata->power_off)
>  		pdata->power_off(dev);
>  err_reset:
> +	pm_runtime_disable(&dev->dev);
>  	while (--rst >= 0)
>  		reset_control_assert(priv->resets[rst]);
>  err_put_clks:
> @@ -292,6 +296,7 @@ static int ohci_platform_remove(struct platform_device *dev)
>  	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
>  	int clk, rst;
>  
> +	pm_runtime_get_sync(&dev->dev);
>  	usb_remove_hcd(hcd);
>  
>  	if (pdata->power_off)
> @@ -305,6 +310,9 @@ static int ohci_platform_remove(struct platform_device *dev)
>  
>  	usb_put_hcd(hcd);
>  
> +	pm_runtime_put_sync(&dev->dev);
> +	pm_runtime_disable(&dev->dev);
> +
>  	if (pdata == &ohci_platform_defaults)
>  		dev->dev.platform_data = NULL;

Acked-by: Alan Stern <stern-nwvwT67g6+6dFdvTe/nMLpVzexx5G7lz@public.gmane.org>

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/3] usb: host: ohci-platform: Add basic runtime PM support

[Roger Quadros]

On 25/05/17 19:13, Tony Lindgren wrote:
> This is needed in preparation of adding support for omap3 and
> later OHCI. The runtime PM will only do something on platforms
> that implement it.
> 
> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Cc: Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org>
> Cc: Sebastian Reichel <sebastian.reichel-ZGY8ohtN/8pPYcu2f3hruQ@public.gmane.org>
> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
> Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>

Acked-by: Roger Quadros <rogerq-l0cyMroinI0@public.gmane.org>

> ---
>  drivers/usb/host/ohci-platform.c | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/drivers/usb/host/ohci-platform.c b/drivers/usb/host/ohci-platform.c
> --- a/drivers/usb/host/ohci-platform.c
> +++ b/drivers/usb/host/ohci-platform.c
> @@ -24,6 +24,7 @@
>  #include <linux/err.h>
>  #include <linux/phy/phy.h>
>  #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
>  #include <linux/reset.h>
>  #include <linux/usb/ohci_pdriver.h>
>  #include <linux/usb.h>
> @@ -242,6 +243,8 @@ static int ohci_platform_probe(struct platform_device *dev)
>  	}
>  #endif
>  
> +	pm_runtime_set_active(&dev->dev);
> +	pm_runtime_enable(&dev->dev);
>  	if (pdata->power_on) {
>  		err = pdata->power_on(dev);
>  		if (err < 0)
> @@ -271,6 +274,7 @@ static int ohci_platform_probe(struct platform_device *dev)
>  	if (pdata->power_off)
>  		pdata->power_off(dev);
>  err_reset:
> +	pm_runtime_disable(&dev->dev);
>  	while (--rst >= 0)
>  		reset_control_assert(priv->resets[rst]);
>  err_put_clks:
> @@ -292,6 +296,7 @@ static int ohci_platform_remove(struct platform_device *dev)
>  	struct ohci_platform_priv *priv = hcd_to_ohci_priv(hcd);
>  	int clk, rst;
>  
> +	pm_runtime_get_sync(&dev->dev);
>  	usb_remove_hcd(hcd);
>  
>  	if (pdata->power_off)
> @@ -305,6 +310,9 @@ static int ohci_platform_remove(struct platform_device *dev)
>  
>  	usb_put_hcd(hcd);
>  
> +	pm_runtime_put_sync(&dev->dev);
> +	pm_runtime_disable(&dev->dev);
> +
>  	if (pdata == &ohci_platform_defaults)
>  		dev->dev.platform_data = NULL;
>  
> 

-- 
cheers,
-roger
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html