From: Guodong Xu <guodong.xu@linaro.org>
To: robh+dt@kernel.org, mark.rutland@arm.com, lee.jones@linaro.org,
ulf.hansson@linaro.org, bhelgaas@google.com,
xuwei5@hisilicon.com, catalin.marinas@arm.com,
will.deacon@arm.com, wangkefeng.wang@huawei.com, arnd@arndb.de,
xuejiancheng@hisilicon.com, puck.chen@hisilicon.com
Cc: zhangfei.gao@linaro.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, linux-mmc@vger.kernel.org,
linux-pci@vger.kernel.org,
Xiaowei Song <songxiaowei@hisilicon.com>,
Guodong Xu <guodong.xu@linaro.org>
Subject: [PATCH v5 15/20] arm64: dts: hisi: add kirin pcie node
Date: Fri, 16 Jun 2017 22:13:22 +0800 [thread overview]
Message-ID: <20170616141322.30466-1-guodong.xu@linaro.org> (raw)
In-Reply-To: <20170615030417.14059-16-guodong.xu@linaro.org>
From: Xiaowei Song <songxiaowei@hisilicon.com>
Add PCIe node for hi3660
Cc: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Xiaowei Song <songxiaowei@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Changes in v5:
* fix interrupt-map, to conform to gic's #address-cells = <0>
* remove redundant status = "ok"
---
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 36 +++++++++++++++++++++++++++++++
1 file changed, 36 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index e138973..8183d71 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -754,5 +754,41 @@
cs-gpios = <&gpio18 5 0>;
status = "disabled";
};
+
+ pcie@f4000000 {
+ compatible = "hisilicon,kirin960-pcie";
+ reg = <0x0 0xf4000000 0x0 0x1000>,
+ <0x0 0xff3fe000 0x0 0x1000>,
+ <0x0 0xf3f20000 0x0 0x40000>,
+ <0x0 0xf5000000 0x0 0x2000>;
+ reg-names = "dbi", "apb", "phy", "config";
+ bus-range = <0x0 0x1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x02000000 0x0 0x00000000
+ 0x0 0xf6000000
+ 0x0 0x02000000>;
+ num-lanes = <1>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0x0 0 0 1
+ &gic GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0 0 2
+ &gic GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0 0 3
+ &gic GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0 0 4
+ &gic GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
+ <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
+ <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
+ <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
+ clock-names = "pcie_phy_ref", "pcie_aux",
+ "pcie_apb_phy", "pcie_apb_sys",
+ "pcie_aclk";
+ reset-gpios = <&gpio11 1 0 >;
+ };
};
};
--
2.10.2
next prev parent reply other threads:[~2017-06-16 14:13 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-15 3:03 [PATCH v4 00/20] arm64: dts: hi3660: add device nodes Guodong Xu
2017-06-15 3:03 ` [PATCH v4 01/20] dt-bindings: arm: hisilicon: add bindings for HiKey960 board Guodong Xu
2017-06-15 3:03 ` [PATCH v4 02/20] arm64: dts: hisilicon: update compatible string for hikey960 Guodong Xu
2017-06-15 3:04 ` [PATCH v4 03/20] arm64: dts: hikey960: pinctrl: add more pinmux and pinconfig Guodong Xu
2017-06-15 3:04 ` [PATCH v4 04/20] arm64: dts: hi3660: add resources for clock and reset Guodong Xu
2017-06-15 3:04 ` [PATCH v4 05/20] arm64: dts: Add I2C nodes for Hi3660 Guodong Xu
2017-06-15 3:04 ` [PATCH v4 07/20] arm64: dts: hi3660: Add uarts nodes Guodong Xu
2017-06-15 3:04 ` [PATCH v4 11/20] arm64: dts: hikey960: add LED nodes Guodong Xu
2017-06-15 3:04 ` [PATCH v4 12/20] arm64: dts: hi3660: add spi device nodes Guodong Xu
2017-06-15 3:04 ` [PATCH v4 13/20] arm64: dts: hi3660: add sp804 timer node Guodong Xu
2017-06-15 3:04 ` [PATCH v4 15/20] arm64: dts: hisi: add kirin pcie node Guodong Xu
2017-06-16 14:13 ` Guodong Xu [this message]
2017-06-16 14:43 ` [PATCH v5 " Wei Xu
2017-06-15 3:04 ` [PATCH v4 16/20] dt-bindings: mfd: hi6421: Add hi6421v530 compatible string Guodong Xu
2017-06-15 3:04 ` [PATCH v4 17/20] arm64: dts: hikey960: add device node for pmic and regulators Guodong Xu
[not found] ` <20170615030417.14059-1-guodong.xu-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2017-06-15 3:04 ` [PATCH v4 06/20] arm64: dts: hi3660: add gpio dtsi file for Hisilicon Hi3660 SOC Guodong Xu
2017-06-15 3:04 ` [PATCH v4 08/20] arm64: dts: hikey960: add WL1837 Bluetooth device node Guodong Xu
2017-06-15 3:04 ` [PATCH v4 09/20] arm64: dts: hi3660: Add pl031 rtc node Guodong Xu
2017-06-15 3:04 ` [PATCH v4 10/20] arm64: dts: hi3660: add power key dts node Guodong Xu
2017-06-15 3:04 ` [PATCH v4 14/20] dt-bindings: PCI: hisi: Add document for PCIe of Kirin SoCs Guodong Xu
2017-06-15 3:04 ` [PATCH v4 18/20] dt-bindings: mmc: dw_mmc-k3: add document of hi3660 mmc Guodong Xu
2017-06-15 3:04 ` [PATCH v4 19/20] arm64: dts: hi3660: add sd/sdio device nodes Guodong Xu
2017-06-15 19:49 ` [PATCH v4 00/20] arm64: dts: hi3660: add " Wei Xu
2017-06-15 3:04 ` [PATCH v4 20/20] arm64: dts: hi3660-hikey960: add nodes for WiFi Guodong Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170616141322.30466-1-guodong.xu@linaro.org \
--to=guodong.xu@linaro.org \
--cc=arnd@arndb.de \
--cc=bhelgaas@google.com \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=puck.chen@hisilicon.com \
--cc=robh+dt@kernel.org \
--cc=songxiaowei@hisilicon.com \
--cc=ulf.hansson@linaro.org \
--cc=wangkefeng.wang@huawei.com \
--cc=will.deacon@arm.com \
--cc=xuejiancheng@hisilicon.com \
--cc=xuwei5@hisilicon.com \
--cc=zhangfei.gao@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).