Re: [PATCH v2 12/25] dt-bindings: qcom_nandc: QPIC NAND documentation

[Boris Brezillon <boris.brezillon-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>]

On Wed, 19 Jul 2017 17:18:00 +0530
Abhishek Sahu <absahu-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org> wrote:

> 1. QPIC NAND will use compatible string "qcom,qpic-nandc-v1.4.0"
> 2. QPIC NAND will 3 BAM channels: command, data tx and data rx
>    while EBI2 NAND uses only single ADM channel.
> 3. CRCI is only required for ADM DMA and its not required for
>    QPIC NAND.
> 
> Signed-off-by: Abhishek Sahu <absahu-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
> ---
>  .../devicetree/bindings/mtd/qcom_nandc.txt         | 54 ++++++++++++++++++++--
>  1 file changed, 51 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> index b24adfe..8efaeb0 100644
> --- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> @@ -1,13 +1,15 @@
>  * Qualcomm NAND controller
>  
>  Required properties:
> -- compatible:		should be "qcom,ebi2-nandc" - EBI2 NAND which uses ADM
> -			DMA like IPQ8064.
> -
> +- compatible:		must be one of the following:
> +	* "qcom,ebi2-nandc" - EBI2 NAND which uses ADM DMA like IPQ8064.
> +	* "qcom,qpic-nandc-v1.4.0" - QPIC NAND v1.4.0 which uses BAM DMA like IPQ4019.
>  - reg:			MMIO address range
>  - clocks:		must contain core clock and always on clock
>  - clock-names:		must contain "core" for the core clock and "aon" for the
>  			always on clock
> +
> +EBI2 specific properties:
>  - dmas:			DMA specifier, consisting of a phandle to the ADM DMA
>  			controller node and the channel number to be used for
>  			NAND. Refer to dma.txt and qcom_adm.txt for more details
> @@ -18,6 +20,12 @@ Required properties:
>  - qcom,data-crci:	must contain the ADM data type CRCI block instance
>  			number specified for the NAND controller on the given
>  			platform
> +
> +QPIC specific properties:
> +- dmas:			DMA specifier, consisting of a phandle to the BAM DMA
> +			and the channel number to be used for NAND. Refer to
> +			dma.txt, qcom_bam_dma.txt for more details
> +- dma-names:		must contain all 3 channel names : "tx", "rx", "cmd"
>  - #address-cells:	<1> - subnodes give the chip-select number
>  - #size-cells:		<0>
>  
> @@ -84,3 +92,43 @@ nand@1ac00000 {
>  		};
>  	};
>  };
> +
> +nand@79b0000 {

I think I already mentioned I'd prefer to have

nand-controller@xxxx {

> +	compatible = "qcom,qpic-nandc-v1.4.0";
> +	reg = <0x79b0000 0x1000>;
> +
> +	clocks = <&gcc GCC_QPIC_CLK>,
> +		<&gcc GCC_QPIC_AHB_CLK>;
> +	clock-names = "core", "aon";
> +
> +	dmas = <&qpicbam 0>,
> +		<&qpicbam 1>,
> +		<&qpicbam 2>;
> +	dma-names = "tx", "rx", "cmd";
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	nandcs@0 {

and
	nand@x {

here.

> +		reg = <0>;
> +		nand-ecc-strength = <4>;
> +		nand-ecc-step-size = <512>;
> +		nand-bus-width = <8>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			partition@0 {
> +				label = "boot-nand";
> +				reg = <0 0x58a0000>;
> +			};
> +
> +			partition@58a0000 {
> +				label = "fs-nand";
> +				reg = <0x58a0000 0x4000000>;
> +			};
> +		};
> +	};
> +};

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html