[PATCH v2 00/10] ARM: dts: Add iodelay data for MMC

[PATCH v2 00/10] ARM: dts: Add iodelay data for MMC

[Kishon Vijay Abraham I]

This series only adds data and it won't be used until
the next series which adds UHS support to omap_hsmmc/sdhci driver.

Changes from v1:
*) Add missing Signed-off-by in a couple of patches
*) Fixed Author of "Move common MMC/SD properties to common file" patch.

Kishon Vijay Abraham I (7):
  ARM: dts: dra7-evm: Add pinmux configuration for MMC
  ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
  ARM: dts: am571x-idk: Add pinmux configuration for MMC
  ARM: dts: am572x-idk: Add pinmux configuration for MMC
  ARM: dts: dra72-evm: Add pinmux configuration for MMC
  ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
  ARM: dts: dra71-evm: Add pinmux configuration for MMC

Sekhar Nori (3):
  ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data
  ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data
  ARM: dts: am57xx-idk: Move common MMC/SD properties to common file

 arch/arm/boot/dts/am571x-idk.dts                |  26 +-
 arch/arm/boot/dts/am572x-idk.dts                |  27 +-
 arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi |  29 +-
 arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts   |  15 +
 arch/arm/boot/dts/am57xx-beagle-x15.dts         |  11 +
 arch/arm/boot/dts/am57xx-idk-common.dtsi        |   8 +
 arch/arm/boot/dts/dra7-evm.dts                  |  22 +-
 arch/arm/boot/dts/dra71-evm.dts                 |  14 +
 arch/arm/boot/dts/dra72-evm-revc.dts            |  14 +
 arch/arm/boot/dts/dra72-evm.dts                 |  14 +
 arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi       | 350 +++++++++++++
 arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi       | 647 ++++++++++++++++++++++++
 12 files changed, 1130 insertions(+), 47 deletions(-)
 create mode 100644 arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
 create mode 100644 arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi

-- 
2.11.0

[PATCH v2 01/10] ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data

[Kishon Vijay Abraham I]

From: Sekhar Nori <nsekhar@ti.com>

Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.

IOdelay data for both silicon revision 1.0 and 2.0 is
added here.

The datamanual revisions used are:
 * AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017
 * AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017
 * DRA71x : SPRS960B, Revised February 2017

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi | 350 ++++++++++++++++++++++++++++++
 1 file changed, 350 insertions(+)
 create mode 100644 arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi

diff --git a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
new file mode 100644
index 000000000000..088013c6dc6e
--- /dev/null
+++ b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
@@ -0,0 +1,350 @@
+/*
+ * MMC IOdelay values for TI's DRA72x, DRA71x and AM571x SoCs.
+ *
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Rules for modifying this file:
+ * a) Update of this file should typically correspond to a datamanual revision.
+ *    Datamanual revision that was used should be updated in comment below.
+ *    If there is no update to datamanual, do not update the values. If you
+ *    need to use values different from that recommended by the datamanual
+ *    for your design, then you should consider adding values to the device-
+ *    -tree file for your board directly.
+ * b) We keep the mode names as close to the datamanual as possible. So
+ *    if the manual calls a mode, DDR50, or DDR or DDR 1.8v or DDR 3.3v,
+ *    we follow that in code too.
+ * c) If the values change between multiple revisions of silicon, we add
+ *    a revision tag to both the new and old entry. Use 'rev10' for PG 1.0,
+ *    'rev20' for PG 2.0 and so on.
+ * d) The node name and node label should be the exact same string. This is
+ *    to curb naming creativity and achieve consistency.
+ * e) If in future, DRA71x and DRA72x values differ, then add 'dra71_' and
+ *    'dra72_' tag to entries. Both the new and old entries should gain a tag.
+ *
+ * Datamanual Revisions:
+ *
+ * AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017
+ * AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017
+ * DRA71x : SPRS960B, Revised February 2017
+ */
+
+&dra7_pmx_core {
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr12: mmc1_pins_sdr12 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_hs: mmc1_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr25: mmc1_pins_sdr25 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr50: mmc1_pins_sdr50 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_ddr50_rev10: mmc1_pins_ddr50_rev10 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_clk.mmc1_clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_cmd.mmc1_cmd */
+			DRA7XX_CORE_IOPAD(0x375C, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_dat0.mmc1_dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_dat1.mmc1_dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_dat2.mmc1_dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_dat3.mmc1_dat3 */
+		>;
+	};
+
+	mmc1_pins_ddr50_rev20: mmc1_pins_ddr50_rev20 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr104: mmc1_pins_sdr104 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc2_pins_default: mmc2_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_hs: mmc2_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_ddr_rev10: mmc2_pins_ddr_rev10 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a22.mmc2_dat7 */
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_cs1.mmc2_cmd */
+		>;
+	};
+
+	mmc2_pins_ddr_rev20: mmc2_pins_ddr_rev20 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_hs200: mmc2_pins_hs200 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+};
+
+&dra7_iodelay_core {
+
+	/* Corresponds to MMC1_MANUAL1 in datamanual */
+	mmc1_iodelay_ddr50_conf: mmc1_iodelay_ddr50_conf {
+		pinctrl-pin-array = <
+			0x618 A_DELAY_PS(588) G_DELAY_PS(0)	/* CFG_MMC1_CLK_IN */
+			0x624 A_DELAY_PS(1000) G_DELAY_PS(0)	/* CFG_MMC1_CMD_IN */
+			0x630 A_DELAY_PS(1375) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_IN */
+			0x63C A_DELAY_PS(1000) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_IN */
+			0x648 A_DELAY_PS(1000) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_IN */
+			0x654 A_DELAY_PS(1000) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_IN */
+			0x620 A_DELAY_PS(1230) G_DELAY_PS(0)	/* CFG_MMC1_CLK_OUT */
+			0x62C A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x638 A_DELAY_PS(56) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x644 A_DELAY_PS(76) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x650 A_DELAY_PS(91) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x65C A_DELAY_PS(99) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+			0x628 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x640 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x64C A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x658 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC1_MANUAL2 in datamanual */
+	mmc1_iodelay_sdr104_rev10_conf: mmc1_iodelay_sdr104_rev10_conf {
+		pinctrl-pin-array = <
+			0x620 A_DELAY_PS(560) G_DELAY_PS(365)	/* CFG_MMC1_CLK_OUT */
+			0x62c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x638 A_DELAY_PS(29) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x644 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x650 A_DELAY_PS(47) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x65c A_DELAY_PS(30) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+			0x628 A_DELAY_PS(125) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x634 A_DELAY_PS(43) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x640 A_DELAY_PS(433) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x64c A_DELAY_PS(287) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x658 A_DELAY_PS(351) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC1_MANUAL2 in datamanual */
+	mmc1_iodelay_sdr104_rev20_conf: mmc1_iodelay_sdr104_rev20_conf {
+		pinctrl-pin-array = <
+			0x620 A_DELAY_PS(520) G_DELAY_PS(320)	/* CFG_MMC1_CLK_OUT */
+			0x62c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x638 A_DELAY_PS(40) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x644 A_DELAY_PS(83) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x650 A_DELAY_PS(98) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x65c A_DELAY_PS(106) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+			0x628 A_DELAY_PS(51) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x640 A_DELAY_PS(363) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x64c A_DELAY_PS(199) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x658 A_DELAY_PS(273) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC2_MANUAL1 in datamanual */
+	mmc2_iodelay_ddr_conf: mmc2_iodelay_ddr_conf {
+		pinctrl-pin-array = <
+			0x18c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_IN */
+			0x1a4 A_DELAY_PS(119) G_DELAY_PS(0)	/* CFG_GPMC_A20_IN */
+			0x1b0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A21_IN */
+			0x1bc A_DELAY_PS(18) G_DELAY_PS(0)	/* CFG_GPMC_A22_IN */
+			0x1c8 A_DELAY_PS(894) G_DELAY_PS(0)	/* CFG_GPMC_A23_IN */
+			0x1d4 A_DELAY_PS(30) G_DELAY_PS(0)	/* CFG_GPMC_A24_IN */
+			0x1e0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_IN */
+			0x1ec A_DELAY_PS(23) G_DELAY_PS(0)	/* CFG_GPMC_A26_IN */
+			0x1f8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_IN */
+			0x360 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_IN */
+			0x194 A_DELAY_PS(152) G_DELAY_PS(0)	/* CFG_GPMC_A19_OUT */
+			0x1ac A_DELAY_PS(206) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b8 A_DELAY_PS(78) G_DELAY_PS(0)	/* CFG_GPMC_A21_OUT */
+			0x1c4 A_DELAY_PS(2) G_DELAY_PS(0)	/* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(266) G_DELAY_PS(0)	/* CFG_GPMC_A23_OUT */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1f4 A_DELAY_PS(43) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x200 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x368 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OUT */
+			0x190 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_OEN */
+			0x1a8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A20_OEN */
+			0x1b4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A21_OEN */
+			0x1c0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A22_OEN */
+			0x1d8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OEN */
+			0x1e4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OEN */
+			0x1f0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A26_OEN */
+			0x1fc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OEN */
+			0x364 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC2_MANUAL3 in datamanual */
+	mmc2_iodelay_hs200_rev10_conf: mmc2_iodelay_hs200_rev10_conf {
+		pinctrl-pin-array = <
+			0x194 A_DELAY_PS(150) G_DELAY_PS(95)	/* CFG_GPMC_A19_OUT */
+			0x1ac A_DELAY_PS(250) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b8 A_DELAY_PS(125) G_DELAY_PS(0)	/* CFG_GPMC_A21_OUT */
+			0x1c4 A_DELAY_PS(100) G_DELAY_PS(0)	/* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(870) G_DELAY_PS(415)	/* CFG_GPMC_A23_OUT */
+			0x1dc A_DELAY_PS(30) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e8 A_DELAY_PS(200) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1f4 A_DELAY_PS(200) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x200 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x368 A_DELAY_PS(240) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OUT */
+			0x190 A_DELAY_PS(695) G_DELAY_PS(0)	/* CFG_GPMC_A19_OEN */
+			0x1a8 A_DELAY_PS(924) G_DELAY_PS(0)	/* CFG_GPMC_A20_OEN */
+			0x1b4 A_DELAY_PS(719) G_DELAY_PS(0)	/* CFG_GPMC_A21_OEN */
+			0x1c0 A_DELAY_PS(824) G_DELAY_PS(0)	/* CFG_GPMC_A22_OEN */
+			0x1d8 A_DELAY_PS(877) G_DELAY_PS(0)	/* CFG_GPMC_A24_OEN */
+			0x1e4 A_DELAY_PS(446) G_DELAY_PS(0)	/* CFG_GPMC_A25_OEN */
+			0x1f0 A_DELAY_PS(847) G_DELAY_PS(0)	/* CFG_GPMC_A26_OEN */
+			0x1fc A_DELAY_PS(586) G_DELAY_PS(0)	/* CFG_GPMC_A27_OEN */
+			0x364 A_DELAY_PS(1039) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC2_MANUAL3 in datamanual */
+	mmc2_iodelay_hs200_rev20_conf: mmc2_iodelay_hs200_rev20_conf {
+		pinctrl-pin-array = <
+			0x194 A_DELAY_PS(285) G_DELAY_PS(0)	/* CFG_GPMC_A19_OUT */
+			0x1ac A_DELAY_PS(189) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b8 A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A21_OUT */
+			0x1c4 A_DELAY_PS(0) G_DELAY_PS(70)	/* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(730) G_DELAY_PS(360)	/* CFG_GPMC_A23_OUT */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1f4 A_DELAY_PS(70) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x200 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x368 A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_CS1_OUT */
+			0x190 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_OEN */
+			0x1a8 A_DELAY_PS(231) G_DELAY_PS(0)	/* CFG_GPMC_A20_OEN */
+			0x1b4 A_DELAY_PS(39) G_DELAY_PS(0)	/* CFG_GPMC_A21_OEN */
+			0x1c0 A_DELAY_PS(91) G_DELAY_PS(0)	/* CFG_GPMC_A22_OEN */
+			0x1d8 A_DELAY_PS(176) G_DELAY_PS(0)	/* CFG_GPMC_A24_OEN */
+			0x1e4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OEN */
+			0x1f0 A_DELAY_PS(101) G_DELAY_PS(0)	/* CFG_GPMC_A26_OEN */
+			0x1fc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OEN */
+			0x364 A_DELAY_PS(360) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OEN */
+		>;
+	};
+};
-- 
2.11.0

[PATCH v2 02/10] ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data

[Kishon Vijay Abraham I]

From: Sekhar Nori <nsekhar@ti.com>

Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.

IOdelay data for both silicon revision 1.1 and 2.0 is
added here.

The datamanual revisions used are:
* AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016
* AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi | 647 ++++++++++++++++++++++++++++++
 1 file changed, 647 insertions(+)
 create mode 100644 arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi

diff --git a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
new file mode 100644
index 000000000000..28ebb4eb884a
--- /dev/null
+++ b/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
@@ -0,0 +1,647 @@
+/*
+ * MMC IOdelay values for TI's DRA74x, DRA75x and AM572x SoCs.
+ *
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Rules for modifying this file:
+ * a) Update of this file should typically correspond to a datamanual revision.
+ *    Datamanual revision that was used should be updated in comment below.
+ *    If there is no update to datamanual, do not update the values. If you
+ *    need to use values different from that recommended by the datamanual
+ *    for your design, then you should consider adding values to the device-
+ *    -tree file for your board directly.
+ * b) We keep the mode names as close to the datamanual as possible. So
+ *    if the manual calls a mode, DDR50, or DDR or DDR 1.8v or DDR 3.3v,
+ *    we follow that in code too.
+ * c) If the values change between multiple revisions of silicon, we add
+ *    a revision tag to both the new and old entry. Use 'rev11' for PG 1.1,
+ *    'rev20' for PG 2.0 and so on.
+ * d) The node name and node label should be the exact same string. This is
+ *    to curb naming creativity and achieve consistency.
+ *
+ * Datamanual Revisions:
+ *
+ * AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016
+ * AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016
+ *
+ */
+
+&dra7_pmx_core {
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr12: mmc1_pins_sdr12 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_hs: mmc1_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr25: mmc1_pins_sdr25 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr50: mmc1_pins_sdr50 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_ddr50: mmc1_pins_ddr50 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr104: mmc1_pins_sdr104 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc2_pins_default: mmc2_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_hs: mmc2_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_ddr_3_3v_rev11: mmc2_pins_ddr_3_3v_rev11 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_ddr_1_8v_rev11: mmc2_pins_ddr_1_8v_rev11 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_ddr_rev20: mmc2_pins_ddr_rev20 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_hs200: mmc2_pins_hs200 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc4_pins_default: mmc4_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
+			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
+			DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
+			DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
+			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
+			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
+		>;
+	};
+
+	mmc4_pins_hs: mmc4_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
+			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
+			DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
+			DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
+			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
+			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
+		>;
+	};
+
+	mmc3_pins_default: mmc3_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+			DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+			DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+			DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+			DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+		>;
+	};
+
+	mmc3_pins_hs: mmc3_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+			DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+			DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+			DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+			DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+		>;
+	};
+
+	mmc3_pins_sdr12: mmc3_pins_sdr12 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+			DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+			DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+			DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+			DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+		>;
+	};
+
+	mmc3_pins_sdr25: mmc3_pins_sdr25 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+			DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+			DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+			DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+			DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+		>;
+	};
+
+	mmc3_pins_sdr50: mmc3_pins_sdr50 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+			DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+			DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+			DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+			DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+		>;
+	};
+
+	mmc4_pins_sdr12: mmc4_pins_sdr12 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
+			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
+			DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
+			DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
+			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
+			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
+		>;
+	};
+
+	mmc4_pins_sdr25: mmc4_pins_sdr25 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
+			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
+			DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
+			DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
+			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
+			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
+		>;
+	};
+};
+
+&dra7_iodelay_core {
+
+	/* Corresponds to MMC1_DDR_MANUAL1 in datamanual */
+	mmc1_iodelay_ddr_rev11_conf: mmc1_iodelay_ddr_rev11_conf {
+		pinctrl-pin-array = <
+			0x618 A_DELAY_PS(572) G_DELAY_PS(540)	/* CFG_MMC1_CLK_IN */
+			0x620 A_DELAY_PS(1525) G_DELAY_PS(0)	/* CFG_MMC1_CLK_OUT */
+			0x624 A_DELAY_PS(0) G_DELAY_PS(600)	/* CFG_MMC1_CMD_IN */
+			0x628 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x62c A_DELAY_PS(55) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x630 A_DELAY_PS(403) G_DELAY_PS(120)	/* CFG_MMC1_DAT0_IN */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x638 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x63c A_DELAY_PS(23) G_DELAY_PS(60)	/* CFG_MMC1_DAT1_IN */
+			0x640 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x644 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x648 A_DELAY_PS(25) G_DELAY_PS(60)	/* CFG_MMC1_DAT2_IN */
+			0x64c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x650 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x654 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_IN */
+			0x658 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+			0x65c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC1_DDR_MANUAL1 in datamanual */
+	mmc1_iodelay_ddr_rev20_conf: mmc1_iodelay_ddr50_rev20_conf {
+		pinctrl-pin-array = <
+			0x618 A_DELAY_PS(1076) G_DELAY_PS(330)	/* CFG_MMC1_CLK_IN */
+			0x620 A_DELAY_PS(1271) G_DELAY_PS(0)	/* CFG_MMC1_CLK_OUT */
+			0x624 A_DELAY_PS(722) G_DELAY_PS(0)	/* CFG_MMC1_CMD_IN */
+			0x628 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x62C A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x630 A_DELAY_PS(751) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_IN */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x638 A_DELAY_PS(20) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x63C A_DELAY_PS(256) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_IN */
+			0x640 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x644 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x648 A_DELAY_PS(263) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_IN */
+			0x64C A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x650 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x654 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_IN */
+			0x658 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+			0x65C A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC1_SDR104_MANUAL1 in datamanual */
+	mmc1_iodelay_sdr104_rev11_conf: mmc1_iodelay_sdr104_rev11_conf {
+		pinctrl-pin-array = <
+			0x620 A_DELAY_PS(1063) G_DELAY_PS(17)	/* CFG_MMC1_CLK_OUT */
+			0x628 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x62c A_DELAY_PS(23) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x638 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x640 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x644 A_DELAY_PS(2) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x64c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x650 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x658 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+			0x65c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC1_SDR104_MANUAL1 in datamanual */
+	mmc1_iodelay_sdr104_rev20_conf: mmc1_iodelay_sdr104_rev20_conf {
+		pinctrl-pin-array = <
+			0x620 A_DELAY_PS(600) G_DELAY_PS(400)	/* CFG_MMC1_CLK_OUT */
+			0x628 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x62c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x638 A_DELAY_PS(30) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x640 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x644 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x64c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x650 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x658 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+			0x65c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC2_HS200_MANUAL1 in datamanual */
+	mmc2_iodelay_hs200_rev11_conf: mmc2_iodelay_hs200_rev11_conf {
+		pinctrl-pin-array = <
+			0x190 A_DELAY_PS(621) G_DELAY_PS(600)	/* CFG_GPMC_A19_OEN */
+			0x194 A_DELAY_PS(300) G_DELAY_PS(0)	/* CFG_GPMC_A19_OUT */
+			0x1a8 A_DELAY_PS(739) G_DELAY_PS(600)	/* CFG_GPMC_A20_OEN */
+			0x1ac A_DELAY_PS(240) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b4 A_DELAY_PS(812) G_DELAY_PS(600)	/* CFG_GPMC_A21_OEN */
+			0x1b8 A_DELAY_PS(240) G_DELAY_PS(0)	/* CFG_GPMC_A21_OUT */
+			0x1c0 A_DELAY_PS(954) G_DELAY_PS(600)	/* CFG_GPMC_A22_OEN */
+			0x1c4 A_DELAY_PS(60)  G_DELAY_PS(0)	/* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(1340) G_DELAY_PS(420)	/* CFG_GPMC_A23_OUT */
+			0x1d8 A_DELAY_PS(935) G_DELAY_PS(600)	/* CFG_GPMC_A24_OEN */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e4 A_DELAY_PS(525) G_DELAY_PS(600)	/* CFG_GPMC_A25_OEN */
+			0x1e8 A_DELAY_PS(120) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1f0 A_DELAY_PS(767) G_DELAY_PS(600)	/* CFG_GPMC_A26_OEN */
+			0x1f4 A_DELAY_PS(225) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x1fc A_DELAY_PS(565) G_DELAY_PS(600)	/* CFG_GPMC_A27_OEN */
+			0x200 A_DELAY_PS(60) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x364 A_DELAY_PS(969) G_DELAY_PS(600)	/* CFG_GPMC_CS1_OEN */
+			0x368 A_DELAY_PS(180) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OUT */
+	      >;
+	};
+
+	/* Corresponds to MMC2_HS200_MANUAL1 in datamanual */
+	mmc2_iodelay_hs200_rev20_conf: mmc2_iodelay_hs200_rev20_conf {
+		pinctrl-pin-array = <
+			0x190 A_DELAY_PS(274) G_DELAY_PS(0)       /* CFG_GPMC_A19_OEN */
+			0x194 A_DELAY_PS(162) G_DELAY_PS(0)       /* CFG_GPMC_A19_OUT */
+			0x1a8 A_DELAY_PS(401) G_DELAY_PS(0)       /* CFG_GPMC_A20_OEN */
+			0x1ac A_DELAY_PS(73) G_DELAY_PS(0)        /* CFG_GPMC_A20_OUT */
+			0x1b4 A_DELAY_PS(465) G_DELAY_PS(0)       /* CFG_GPMC_A21_OEN */
+			0x1b8 A_DELAY_PS(115) G_DELAY_PS(0)       /* CFG_GPMC_A21_OUT */
+			0x1c0 A_DELAY_PS(633) G_DELAY_PS(0)       /* CFG_GPMC_A22_OEN */
+			0x1c4 A_DELAY_PS(47) G_DELAY_PS(0)        /* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(935) G_DELAY_PS(280)     /* CFG_GPMC_A23_OUT */
+			0x1d8 A_DELAY_PS(621) G_DELAY_PS(0)       /* CFG_GPMC_A24_OEN */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)         /* CFG_GPMC_A24_OUT */
+			0x1e4 A_DELAY_PS(183) G_DELAY_PS(0)       /* CFG_GPMC_A25_OEN */
+			0x1e8 A_DELAY_PS(0) G_DELAY_PS(0)         /* CFG_GPMC_A25_OUT */
+			0x1f0 A_DELAY_PS(467) G_DELAY_PS(0)       /* CFG_GPMC_A26_OEN */
+			0x1f4 A_DELAY_PS(0) G_DELAY_PS(0)         /* CFG_GPMC_A26_OUT */
+			0x1fc A_DELAY_PS(262) G_DELAY_PS(0)       /* CFG_GPMC_A27_OEN */
+			0x200 A_DELAY_PS(46) G_DELAY_PS(0)        /* CFG_GPMC_A27_OUT */
+			0x364 A_DELAY_PS(684) G_DELAY_PS(0)       /* CFG_GPMC_CS1_OEN */
+			0x368 A_DELAY_PS(76) G_DELAY_PS(0)        /* CFG_GPMC_CS1_OUT */
+	      >;
+	};
+
+	/* Correspnds to MMC2_DDR_3V3_MANUAL1 in datamanual */
+	mmc2_iodelay_ddr_3_3v_rev11_conf: mmc2_iodelay_ddr_3_3v_rev11_conf {
+		pinctrl-pin-array = <
+			0x18c A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A19_IN */
+			0x190 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_OEN */
+			0x194 A_DELAY_PS(174) G_DELAY_PS(0)	/* CFG_GPMC_A19_OUT */
+			0x1a4 A_DELAY_PS(265) G_DELAY_PS(360)	/* CFG_GPMC_A20_IN */
+			0x1a8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A20_OEN */
+			0x1ac A_DELAY_PS(168) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b0 A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A21_IN */
+			0x1b4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A21_OEN */
+			0x1b8 A_DELAY_PS(136) G_DELAY_PS(0)	/* CFG_GPMC_A21_OUT */
+			0x1bc A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A22_IN */
+			0x1c0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A22_OEN */
+			0x1c4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A22_OUT */
+			0x1c8 A_DELAY_PS(287) G_DELAY_PS(420)	/* CFG_GPMC_A23_IN */
+			0x1d0 A_DELAY_PS(879) G_DELAY_PS(0)	/* CFG_GPMC_A23_OUT */
+			0x1d4 A_DELAY_PS(144) G_DELAY_PS(240)	/* CFG_GPMC_A24_IN */
+			0x1d8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OEN */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_IN */
+			0x1e4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OEN */
+			0x1e8 A_DELAY_PS(34) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1ec A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A26_IN */
+			0x1f0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A26_OEN */
+			0x1f4 A_DELAY_PS(120) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x1f8 A_DELAY_PS(120) G_DELAY_PS(180)	/* CFG_GPMC_A27_IN */
+			0x1fc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OEN */
+			0x200 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x360 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_IN */
+			0x364 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OEN */
+			0x368 A_DELAY_PS(11) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC2_DDR_1V8_MANUAL1 in datamanual */
+	mmc2_iodelay_ddr_1_8v_rev11_conf: mmc2_iodelay_ddr_1_8v_rev11_conf {
+		pinctrl-pin-array = <
+			0x18c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_IN */
+			0x190 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_OEN */
+			0x194 A_DELAY_PS(174) G_DELAY_PS(0)	/* CFG_GPMC_A19_OUT */
+			0x1a4 A_DELAY_PS(274) G_DELAY_PS(240)	/* CFG_GPMC_A20_IN */
+			0x1a8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A20_OEN */
+			0x1ac A_DELAY_PS(168) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b0 A_DELAY_PS(0) G_DELAY_PS(60)	/* CFG_GPMC_A21_IN */
+			0x1b4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A21_OEN */
+			0x1b8 A_DELAY_PS(136) G_DELAY_PS(0)	/* CFG_GPMC_A21_OUT */
+			0x1bc A_DELAY_PS(0) G_DELAY_PS(60)	/* CFG_GPMC_A22_IN */
+			0x1c0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A22_OEN */
+			0x1c4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A22_OUT */
+			0x1c8 A_DELAY_PS(514) G_DELAY_PS(360)	/* CFG_GPMC_A23_IN */
+			0x1d0 A_DELAY_PS(879) G_DELAY_PS(0)	/* CFG_GPMC_A23_OUT */
+			0x1d4 A_DELAY_PS(187) G_DELAY_PS(120)	/* CFG_GPMC_A24_IN */
+			0x1d8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OEN */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_IN */
+			0x1e4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OEN */
+			0x1e8 A_DELAY_PS(34) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1ec A_DELAY_PS(0) G_DELAY_PS(60)	/* CFG_GPMC_A26_IN */
+			0x1f0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A26_OEN */
+			0x1f4 A_DELAY_PS(120) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x1f8 A_DELAY_PS(121) G_DELAY_PS(60)	/* CFG_GPMC_A27_IN */
+			0x1fc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OEN */
+			0x200 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x360 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_IN */
+			0x364 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OEN */
+			0x368 A_DELAY_PS(11) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC3_MANUAL1 in datamanual */
+	mmc3_iodelay_manual1_rev20_conf: mmc3_iodelay_manual1_conf {
+		pinctrl-pin-array = <
+			0x678 A_DELAY_PS(0) G_DELAY_PS(386)	/* CFG_MMC3_CLK_IN */
+			0x680 A_DELAY_PS(605) G_DELAY_PS(0)	/* CFG_MMC3_CLK_OUT */
+			0x684 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_IN */
+			0x688 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_OEN */
+			0x68c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_OUT */
+			0x690 A_DELAY_PS(171) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_IN */
+			0x694 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_OEN */
+			0x698 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_OUT */
+			0x69c A_DELAY_PS(221) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_IN */
+			0x6a0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_OEN */
+			0x6a4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_OUT */
+			0x6a8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_IN */
+			0x6ac A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_OEN */
+			0x6b0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_OUT */
+			0x6b4 A_DELAY_PS(474) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_IN */
+			0x6b8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_OEN */
+			0x6bc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC3_MANUAL1 in datamanual */
+	mmc3_iodelay_manual1_rev11_conf: mmc3_iodelay_manual1_conf {
+		pinctrl-pin-array = <
+			0x678 A_DELAY_PS(406) G_DELAY_PS(0)	/* CFG_MMC3_CLK_IN */
+			0x680 A_DELAY_PS(659) G_DELAY_PS(0)	/* CFG_MMC3_CLK_OUT */
+			0x684 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_IN */
+			0x688 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_OEN */
+			0x68c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_OUT */
+			0x690 A_DELAY_PS(130) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_IN */
+			0x694 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_OEN */
+			0x698 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_OUT */
+			0x69c A_DELAY_PS(169) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_IN */
+			0x6a0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_OEN */
+			0x6a4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_OUT */
+			0x6a8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_IN */
+			0x6ac A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_OEN */
+			0x6b0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_OUT */
+			0x6b4 A_DELAY_PS(457) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_IN */
+			0x6b8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_OEN */
+			0x6bc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC4_DS_MANUAL1 in datamanual */
+	mmc4_iodelay_ds_rev11_conf: mmc4_iodelay_ds_rev11_conf {
+		pinctrl-pin-array = <
+			0x840 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_IN */
+			0x848 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_OUT */
+			0x84c A_DELAY_PS(96) G_DELAY_PS(0)	/* CFG_UART1_RTSN_IN */
+			0x850 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OEN */
+			0x854 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OUT */
+			0x870 A_DELAY_PS(582) G_DELAY_PS(0)	/* CFG_UART2_CTSN_IN */
+			0x874 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OEN */
+			0x878 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OUT */
+			0x87c A_DELAY_PS(391) G_DELAY_PS(0)	/* CFG_UART2_RTSN_IN */
+			0x880 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OEN */
+			0x884 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OUT */
+			0x888 A_DELAY_PS(561) G_DELAY_PS(0)	/* CFG_UART2_RXD_IN */
+			0x88c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OEN */
+			0x890 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OUT */
+			0x894 A_DELAY_PS(588) G_DELAY_PS(0)	/* CFG_UART2_TXD_IN */
+			0x898 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OEN */
+			0x89c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC4_DS_MANUAL1 in datamanual */
+	mmc4_iodelay_ds_rev20_conf: mmc4_iodelay_ds_rev20_conf {
+		pinctrl-pin-array = <
+			0x840 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_IN */
+			0x848 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_OUT */
+			0x84c A_DELAY_PS(307) G_DELAY_PS(0)	/* CFG_UART1_RTSN_IN */
+			0x850 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OEN */
+			0x854 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OUT */
+			0x870 A_DELAY_PS(785) G_DELAY_PS(0)	/* CFG_UART2_CTSN_IN */
+			0x874 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OEN */
+			0x878 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OUT */
+			0x87c A_DELAY_PS(613) G_DELAY_PS(0)	/* CFG_UART2_RTSN_IN */
+			0x880 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OEN */
+			0x884 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OUT */
+			0x888 A_DELAY_PS(683) G_DELAY_PS(0)	/* CFG_UART2_RXD_IN */
+			0x88c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OEN */
+			0x890 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OUT */
+			0x894 A_DELAY_PS(835) G_DELAY_PS(0)	/* CFG_UART2_TXD_IN */
+			0x898 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OEN */
+			0x89c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC4_MANUAL1 in datamanual */
+	mmc4_iodelay_sdr12_hs_sdr25_rev11_conf: mmc4_iodelay_sdr12_hs_sdr25_rev11_conf {
+		pinctrl-pin-array = <
+			0x840 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_IN */
+			0x848 A_DELAY_PS(2651) G_DELAY_PS(0)	/* CFG_UART1_CTSN_OUT */
+			0x84c A_DELAY_PS(1572) G_DELAY_PS(0)	/* CFG_UART1_RTSN_IN */
+			0x850 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OEN */
+			0x854 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OUT */
+			0x870 A_DELAY_PS(1913) G_DELAY_PS(0)	/* CFG_UART2_CTSN_IN */
+			0x874 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OEN */
+			0x878 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OUT */
+			0x87c A_DELAY_PS(1721) G_DELAY_PS(0)	/* CFG_UART2_RTSN_IN */
+			0x880 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OEN */
+			0x884 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OUT */
+			0x888 A_DELAY_PS(1891) G_DELAY_PS(0)	/* CFG_UART2_RXD_IN */
+			0x88c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OEN */
+			0x890 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OUT */
+			0x894 A_DELAY_PS(1919) G_DELAY_PS(0)	/* CFG_UART2_TXD_IN */
+			0x898 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OEN */
+			0x89c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC4_MANUAL1 in datamanual */
+	mmc4_iodelay_sdr12_hs_sdr25_rev20_conf: mmc4_iodelay_sdr12_hs_sdr25_rev20_conf {
+		pinctrl-pin-array = <
+			0x840 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_IN */
+			0x848 A_DELAY_PS(1147) G_DELAY_PS(0)	/* CFG_UART1_CTSN_OUT */
+			0x84c A_DELAY_PS(1834) G_DELAY_PS(0)	/* CFG_UART1_RTSN_IN */
+			0x850 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OEN */
+			0x854 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OUT */
+			0x870 A_DELAY_PS(2165) G_DELAY_PS(0)	/* CFG_UART2_CTSN_IN */
+			0x874 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OEN */
+			0x878 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OUT */
+			0x87c A_DELAY_PS(1929) G_DELAY_PS(64)	/* CFG_UART2_RTSN_IN */
+			0x880 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OEN */
+			0x884 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OUT */
+			0x888 A_DELAY_PS(1935) G_DELAY_PS(128)	/* CFG_UART2_RXD_IN */
+			0x88c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OEN */
+			0x890 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OUT */
+			0x894 A_DELAY_PS(2172) G_DELAY_PS(44)	/* CFG_UART2_TXD_IN */
+			0x898 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OEN */
+			0x89c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OUT */
+		>;
+	};
+};
-- 
2.11.0

[PATCH v2 03/10] ARM: dts: dra7-evm: Add pinmux configuration for MMC

[Kishon Vijay Abraham I]

Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/dra7-evm.dts | 22 ++++++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 5e3f9ba861f0..aa426dabb6c3 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -9,6 +9,7 @@
 
 #include "dra74x.dtsi"
 #include "dra7-evm-common.dtsi"
+#include "dra74x-mmc-iodelay.dtsi"
 
 / {
 	model = "TI DRA742";
@@ -326,8 +327,6 @@
 
 &mmc1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_default>;
 	vmmc-supply = <&evm_3v3_sd>;
 	vqmmc-supply = <&ldo1_reg>;
 	bus-width = <4>;
@@ -336,14 +335,29 @@
 	 * is always hardwired.
 	 */
 	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+	pinctrl-2 = <&mmc1_pins_sdr12>;
+	pinctrl-3 = <&mmc1_pins_sdr25>;
+	pinctrl-4 = <&mmc1_pins_sdr50>;
+	pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
+	pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
+	pinctrl-7 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
+	pinctrl-8 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
 };
 
 &mmc2 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_default>;
 	vmmc-supply = <&evm_1v8_sw>;
 	bus-width = <8>;
+	pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr_1_8v_rev11 &mmc2_iodelay_ddr_1_8v_rev11_conf>;
+	pinctrl-3 = <&mmc2_pins_ddr_rev20>;
+	pinctrl-4 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev11_conf>;
+	pinctrl-5 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
 };
 
 &cpu0 {
-- 
2.11.0

[PATCH v2 04/10] ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC

[Kishon Vijay Abraham I]

Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 29 +------------------------
 arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts   | 15 +++++++++++++
 arch/arm/boot/dts/am57xx-beagle-x15.dts         | 11 ++++++++++
 3 files changed, 27 insertions(+), 28 deletions(-)

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index d433a50cd18a..49aeecd312b4 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -9,6 +9,7 @@
 
 #include "dra74x.dtsi"
 #include "am57xx-commercial-grade.dtsi"
+#include "dra74x-mmc-iodelay.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
@@ -166,34 +167,6 @@
 	};
 };
 
-&dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-};
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
index 578398c781b1..5a77b334923d 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
@@ -19,10 +19,25 @@
 };
 
 &mmc1 {
+	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+	pinctrl-2 = <&mmc1_pins_sdr12>;
+	pinctrl-3 = <&mmc1_pins_sdr25>;
+	pinctrl-4 = <&mmc1_pins_sdr50>;
+	pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
+	pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
 	vmmc-supply = <&vdd_3v3>;
 	vqmmc-supply = <&ldo1_reg>;
 };
 
+&mmc2 {
+	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;
+};
+
 /* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
 &phy1 {
 	max-speed = <100>;
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 19a60a11c198..d6689106d2a8 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -20,9 +20,20 @@
 };
 
 &mmc1 {
+	pinctrl-names = "default", "hs";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+
 	vmmc-supply = <&ldo1_reg>;
 };
 
+&mmc2 {
+	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;
+};
+
 /* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
 &phy1 {
 	max-speed = <100>;
-- 
2.11.0

[PATCH v2 05/10] ARM: dts: am57xx-idk: Move common MMC/SD properties to common file

[Kishon Vijay Abraham I]

From: Sekhar Nori <nsekhar@ti.com>

AM572x IDK and AM571x IDK boards have equivalent
design of how SD card and eMMC are connected.

The two EVMs mainly differ in IOdelay configuration
needed (because of difference in SoC used).

Move the common properties to am57xx-idk-common.dtsi
file which is common for both EVMs.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/am571x-idk.dts         | 7 -------
 arch/arm/boot/dts/am572x-idk.dts         | 8 --------
 arch/arm/boot/dts/am57xx-idk-common.dtsi | 8 ++++++++
 3 files changed, 8 insertions(+), 15 deletions(-)

diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index 0c0bb4e93f25..78c5c7462fcc 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -64,13 +64,6 @@
 	};
 };
 
-&mmc1 {
-	status = "okay";
-	vmmc-supply = <&ldo1_reg>;
-	bus-width = <4>;
-	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
-};
-
 &omap_dwc3_2 {
 	extcon = <&extcon_usb2>;
 };
diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts
index 604d52554eda..5b22944fedad 100644
--- a/arch/arm/boot/dts/am572x-idk.dts
+++ b/arch/arm/boot/dts/am572x-idk.dts
@@ -76,14 +76,6 @@
 	vbus-gpio = <&gpio3 26 GPIO_ACTIVE_HIGH>;
 };
 
-&mmc1 {
-	status = "okay";
-	vmmc-supply = <&v3_3d>;
-	vqmmc-supply = <&ldo1_reg>;
-	bus-width = <4>;
-	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
-};
-
 &sn65hvs882 {
 	load-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 };
diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi
index c536b2f5389f..97aa8e6a56da 100644
--- a/arch/arm/boot/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi
@@ -399,6 +399,14 @@
 	dr_mode = "peripheral";
 };
 
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&v3_3d>;
+	vqmmc-supply = <&ldo1_reg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
+};
+
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&v3_3d>;
-- 
2.11.0

[PATCH v2 06/10] ARM: dts: am571x-idk: Add pinmux configuration for MMC

[Kishon Vijay Abraham I]

Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/am571x-idk.dts | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index 78c5c7462fcc..debf9464403e 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -11,6 +11,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include "am57xx-idk-common.dtsi"
+#include "dra72x-mmc-iodelay.dtsi"
 
 / {
 	model = "TI AM5718 IDK";
@@ -98,3 +99,21 @@
 &pcie1_ep {
 	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 };
+
+&mmc1 {
+	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+	pinctrl-2 = <&mmc1_pins_sdr12>;
+	pinctrl-3 = <&mmc1_pins_sdr25>;
+	pinctrl-4 = <&mmc1_pins_sdr50>;
+	pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>;
+	pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
+};
+
+&mmc2 {
+	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
+};
-- 
2.11.0

[PATCH v2 07/10] ARM: dts: am572x-idk: Add pinmux configuration for MMC

[Kishon Vijay Abraham I]

Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am572x-idk.dts.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/am572x-idk.dts | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts
index 5b22944fedad..a578fe97ba3b 100644
--- a/arch/arm/boot/dts/am572x-idk.dts
+++ b/arch/arm/boot/dts/am572x-idk.dts
@@ -12,6 +12,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include "am57xx-idk-common.dtsi"
+#include "dra74x-mmc-iodelay.dtsi"
 
 / {
 	model = "TI AM5728 IDK";
@@ -67,6 +68,24 @@
 	};
 };
 
+&mmc1 {
+	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+	pinctrl-2 = <&mmc1_pins_sdr12>;
+	pinctrl-3 = <&mmc1_pins_sdr25>;
+	pinctrl-4 = <&mmc1_pins_sdr50>;
+	pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
+	pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
+};
+
+&mmc2 {
+	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr_rev20>;
+};
+
 &omap_dwc3_2 {
 	extcon = <&extcon_usb2>;
 };
-- 
2.11.0

[PATCH v2 08/10] ARM: dts: dra72-evm: Add pinmux configuration for MMC

[Kishon Vijay Abraham I]

Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm.dts.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/dra72-evm.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index 99fdb3d8445b..c572693b1665 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -6,6 +6,7 @@
  * published by the Free Software Foundation.
  */
 #include "dra72-evm-common.dtsi"
+#include "dra72x-mmc-iodelay.dtsi"
 / {
 	model = "TI DRA722";
 
@@ -55,9 +56,22 @@
 };
 
 &mmc1 {
+	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+	pinctrl-2 = <&mmc1_pins_sdr12>;
+	pinctrl-3 = <&mmc1_pins_sdr25>;
+	pinctrl-4 = <&mmc1_pins_sdr50>;
+	pinctrl-5 = <&mmc1_pins_ddr50_rev10>;
+	pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev10_conf>;
 	vqmmc-supply = <&ldo1_reg>;
 };
 
 &mmc2 {
+	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr_rev10>;
+	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev10_conf>;
 	vmmc-supply = <&evm_1v8_sw>;
 };
-- 
2.11.0

[PATCH v2 09/10] ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC

[Kishon Vijay Abraham I]

Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm-revc.dts.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/dra72-evm-revc.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/dra72-evm-revc.dts
index 9b439851ff79..bf588d00728d 100644
--- a/arch/arm/boot/dts/dra72-evm-revc.dts
+++ b/arch/arm/boot/dts/dra72-evm-revc.dts
@@ -6,6 +6,7 @@
  * published by the Free Software Foundation.
  */
 #include "dra72-evm-common.dtsi"
+#include "dra72x-mmc-iodelay.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
 
 / {
@@ -96,9 +97,22 @@
 };
 
 &mmc1 {
+	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+	pinctrl-2 = <&mmc1_pins_sdr12>;
+	pinctrl-3 = <&mmc1_pins_sdr25>;
+	pinctrl-4 = <&mmc1_pins_sdr50>;
+	pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>;
+	pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
 	vqmmc-supply = <&ldo1_reg>;
 };
 
 &mmc2 {
+	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
+	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
 	vmmc-supply = <&evm_1v8_sw>;
 };
-- 
2.11.0

[PATCH v2 10/10] ARM: dts: dra71-evm: Add pinmux configuration for MMC

[Kishon Vijay Abraham I]

Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra71-evm.dts.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/dra71-evm.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts
index 49e3c76bcf97..41c9132eb550 100644
--- a/arch/arm/boot/dts/dra71-evm.dts
+++ b/arch/arm/boot/dts/dra71-evm.dts
@@ -7,6 +7,7 @@
  */
 
 #include "dra72-evm-common.dtsi"
+#include "dra72x-mmc-iodelay.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
 
 / {
@@ -172,10 +173,23 @@
 };
 
 &mmc1 {
+	pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
+	pinctrl-2 = <&mmc1_pins_sdr12>;
+	pinctrl-3 = <&mmc1_pins_sdr25>;
+	pinctrl-4 = <&mmc1_pins_sdr50>;
+	pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>;
+	pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
 	vqmmc-supply = <&vpo_sd_1v8_3v3>;
 };
 
 &mmc2 {
+	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
+	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
+	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
 	vmmc-supply = <&evm_1v8_sw>;
 };
 
-- 
2.11.0

Re: [PATCH v2 00/10] ARM: dts: Add iodelay data for MMC

[Tony Lindgren]

* Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org> [170816 06:45]:
> This series only adds data and it won't be used until
> the next series which adds UHS support to omap_hsmmc/sdhci driver.
> 
> Changes from v1:
> *) Add missing Signed-off-by in a couple of patches
> *) Fixed Author of "Move common MMC/SD properties to common file" patch.

Thanks for fixing these, applied and pushed out to
omap-for-v4.14/dt-v3 branch.

Regards,

Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html