* [PATCH 1/4] ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet
2017-10-04 18:58 [PATCH 0/4] Sony Xperia Z2 Tablet Initial DTS Bjorn Andersson
@ 2017-10-04 18:58 ` Bjorn Andersson
2017-10-13 12:05 ` Linus Walleij
2017-10-04 18:58 ` [PATCH 2/4] ARM: qcom_defconfig: Resync with new Kconfig options Bjorn Andersson
` (2 subsequent siblings)
3 siblings, 1 reply; 6+ messages in thread
From: Bjorn Andersson @ 2017-10-04 18:58 UTC (permalink / raw)
To: Andy Gross
Cc: Rob Herring, Mark Rutland, devicetree, linux-arm-kernel,
linux-kernel, linux-arm-msm, linux-soc
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This adds a basic DTS file for the Sony Xperia Z2 Tablet, containing
definitions for regulators, eMMC/SD-card, USB, WiFi, Touchscreen,
charger, backlight, coincell and buttons.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/qcom-msm8974-sony-xperia-castor.dts | 641 +++++++++++++++++++++
arch/arm/boot/dts/qcom-msm8974.dtsi | 14 +
arch/arm/boot/dts/qcom-msm8974pro.dtsi | 18 +
4 files changed, 674 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
create mode 100644 arch/arm/boot/dts/qcom-msm8974pro.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index faf46abaa4a2..4da1b19178ec 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -701,6 +701,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \
qcom-msm8974-lge-nexus5-hammerhead.dtb \
+ qcom-msm8974-sony-xperia-castor.dtb \
qcom-msm8974-sony-xperia-honami.dtb \
qcom-mdm9615-wp8548-mangoh-green.dtb
dtb-$(CONFIG_ARCH_REALVIEW) += \
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
new file mode 100644
index 000000000000..e87f2c99060d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
@@ -0,0 +1,641 @@
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+ model = "Sony Xperia Z2 Tablet";
+ compatible = "sony,xperia-castor", "qcom,msm8974";
+
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ input-name = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pin_a>;
+
+ volume-down {
+ label = "volume_down";
+ gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ camera-snapshot {
+ label = "camera_snapshot";
+ gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_CAMERA>;
+ };
+
+ camera-focus {
+ label = "camera_focus";
+ gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_CAMERA_FOCUS>;
+ };
+
+ volume-up {
+ label = "volume_up";
+ gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ smd {
+ rpm {
+ rpm_requests {
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-system-load = <154000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ regulator-system-load = <500000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ };
+
+ vreg_bl_vddio: lcd-backlight-vddio {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_bl_vddio";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+
+ gpio = <&msmgpio 69 0>;
+ enable-active-high;
+
+ vin-supply = <&pm8941_s3>;
+ startup-delay-us = <70000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_backlight_en_pin_a>;
+ };
+
+ vreg_vsp: lcd-dcdc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_vsp";
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+
+ gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_dcdc_en_pin_a>;
+ };
+
+ vreg_wlan: wlan-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_regulator_pin>;
+ };
+};
+
+&soc {
+ sdhci@f9824900 {
+ status = "ok";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+ };
+
+ sdhci@f9864900 {
+ status = "ok";
+
+ max-frequency = <100000000>;
+ non-removable;
+ vmmc-supply = <&vreg_wlan>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc3_pin_a>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bcrmf@1 {
+ compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ brcm,drive-strength = <10>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_sleep_clk_pin>;
+ };
+ };
+
+ sdhci@f98a4900 {
+ status = "ok";
+
+ bus-width = <4>;
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+ };
+
+ serial@f991e000 {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_pin_a>;
+ };
+
+ usb@f9a55000 {
+ status = "ok";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "ok";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
+ };
+ };
+
+ pinctrl@fd510000 {
+ blsp1_uart2_pin_a: blsp1-uart2-pin-active {
+ rx {
+ pins = "gpio5";
+ function = "blsp_uart2";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ tx {
+ pins = "gpio4";
+ function = "blsp_uart2";
+
+ drive-strength = <4>;
+ bias-disable;
+ };
+ };
+
+ i2c8_pins: i2c8 {
+ mux {
+ pins = "gpio47", "gpio48";
+ function = "blsp_i2c8";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ lcd_backlight_en_pin_a: lcd-backlight-vddio {
+ pins = "gpio69";
+ drive-strength = <10>;
+ output-low;
+ bias-disable;
+ };
+
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ sdhc3_pin_a: sdhc3-pin-active {
+ clk {
+ pins = "gpio40";
+ function = "sdc3";
+
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ cmd {
+ pins = "gpio39";
+ function = "sdc3";
+
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ data {
+ pins = "gpio35", "gpio36", "gpio37", "gpio38";
+ function = "sdc3";
+
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ ts_int_pin: synaptics {
+ pin {
+ pins = "gpio86";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
+ };
+ };
+
+ i2c@f9964000 {
+ status = "ok";
+
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c8_pins>;
+
+ synaptics@2c {
+ compatible = "syna,rmi-i2c";
+ reg = <0x2c>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_pin>;
+
+ rmi-f01@1 {
+ reg = <0x1>;
+ syna,nosleep = <1>;
+ };
+
+ rmi-f11@11 {
+ reg = <0x11>;
+ syna,f11-flip-x = <1>;
+ syna,sensor-type = <1>;
+ };
+ };
+ };
+
+ i2c@f9967000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c11_pins>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ lp8566_wled: backlight@2c {
+ compatible = "ti,lp8556";
+ reg = <0x2c>;
+ power-supply = <&vreg_bl_vddio>;
+
+ bl-name = "backlight";
+ dev-ctrl = /bits/ 8 <0x05>;
+ init-brt = /bits/ 8 <0x3f>;
+ rom_a0h {
+ rom-addr = /bits/ 8 <0xa0>;
+ rom-val = /bits/ 8 <0xff>;
+ };
+ rom_a1h {
+ rom-addr = /bits/ 8 <0xa1>;
+ rom-val = /bits/ 8 <0x3f>;
+ };
+ rom_a2h {
+ rom-addr = /bits/ 8 <0xa2>;
+ rom-val = /bits/ 8 <0x20>;
+ };
+ rom_a3h {
+ rom-addr = /bits/ 8 <0xa3>;
+ rom-val = /bits/ 8 <0x5e>;
+ };
+ rom_a4h {
+ rom-addr = /bits/ 8 <0xa4>;
+ rom-val = /bits/ 8 <0x02>;
+ };
+ rom_a5h {
+ rom-addr = /bits/ 8 <0xa5>;
+ rom-val = /bits/ 8 <0x04>;
+ };
+ rom_a6h {
+ rom-addr = /bits/ 8 <0xa6>;
+ rom-val = /bits/ 8 <0x80>;
+ };
+ rom_a7h {
+ rom-addr = /bits/ 8 <0xa7>;
+ rom-val = /bits/ 8 <0xf7>;
+ };
+ rom_a9h {
+ rom-addr = /bits/ 8 <0xa9>;
+ rom-val = /bits/ 8 <0x80>;
+ };
+ rom_aah {
+ rom-addr = /bits/ 8 <0xaa>;
+ rom-val = /bits/ 8 <0x0f>;
+ };
+ rom_aeh {
+ rom-addr = /bits/ 8 <0xae>;
+ rom-val = /bits/ 8 <0x0f>;
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pm8941@0 {
+ charger@1000 {
+ qcom,fast-charge-safe-current = <1500000>;
+ qcom,fast-charge-current-limit = <1500000>;
+ qcom,dc-current-limit = <1800000>;
+ qcom,fast-charge-safe-voltage = <4400000>;
+ qcom,fast-charge-high-threshold-voltage = <4350000>;
+ qcom,fast-charge-low-threshold-voltage = <3400000>;
+ qcom,auto-recharge-threshold-voltage = <4200000>;
+ qcom,minimum-input-voltage = <4300000>;
+ };
+
+ gpios@c000 {
+ gpio_keys_pin_a: gpio-keys-active {
+ pins = "gpio2", "gpio5";
+ function = "normal";
+
+ bias-pull-up;
+ power-source = <PM8941_GPIO_S3>;
+ };
+
+ wlan_sleep_clk_pin: wl-sleep-clk {
+ pins = "gpio17";
+ function = "func2";
+
+ output-high;
+ power-source = <PM8941_GPIO_S3>;
+ };
+
+ wlan_regulator_pin: wl-reg-active {
+ pins = "gpio18";
+ function = "normal";
+
+ bias-disable;
+ power-source = <PM8941_GPIO_S3>;
+ };
+
+ lcd_dcdc_en_pin_a: lcd-dcdc-en-active {
+ pins = "gpio20";
+ function = "normal";
+
+ bias-disable;
+ power-source = <PM8941_GPIO_S3>;
+ input-disable;
+ output-low;
+ };
+
+ };
+
+ coincell@2800 {
+ status = "ok";
+ qcom,rset-ohms = <2100>;
+ qcom,vset-millivolts = <3000>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index a39207625354..75cae87219d6 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -613,6 +613,20 @@
status = "disabled";
};
+ sdhci@f9864900 {
+ compatible = "qcom,sdhci-msm-v4";
+ reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+ reg-names = "hc_mem", "core_mem";
+ interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>,
+ <GIC_SPI 224 IRQ_TYPE_NONE>;
+ interrupt-names = "hc_irq", "pwr_irq";
+ clocks = <&gcc GCC_SDCC3_APPS_CLK>,
+ <&gcc GCC_SDCC3_AHB_CLK>,
+ <&xo_board>;
+ clock-names = "core", "iface", "xo";
+ status = "disabled";
+ };
+
sdhci@f98a4900 {
compatible = "qcom,sdhci-msm-v4";
reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
diff --git a/arch/arm/boot/dts/qcom-msm8974pro.dtsi b/arch/arm/boot/dts/qcom-msm8974pro.dtsi
new file mode 100644
index 000000000000..6740a4cb7da8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974pro.dtsi
@@ -0,0 +1,18 @@
+#include "qcom-msm8974.dtsi"
+
+/ {
+ soc {
+ sdhci@f9824900 {
+ clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+ <&gcc GCC_SDCC1_AHB_CLK>,
+ <&xo_board>,
+ <&gcc GCC_SDCC1_CDCCAL_FF_CLK>,
+ <&gcc GCC_SDCC1_CDCCAL_SLEEP_CLK>;
+ clock-names = "core", "iface", "xo", "cal", "sleep";
+ };
+
+ clock-controller@fc400000 {
+ compatible = "qcom,gcc-msm8974pro";
+ };
+ };
+};
--
2.12.0
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 2/4] ARM: qcom_defconfig: Resync with new Kconfig options
2017-10-04 18:58 [PATCH 0/4] Sony Xperia Z2 Tablet Initial DTS Bjorn Andersson
2017-10-04 18:58 ` [PATCH 1/4] ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet Bjorn Andersson
@ 2017-10-04 18:58 ` Bjorn Andersson
2017-10-04 18:58 ` [PATCH 3/4] ARM: qcom_defconfig: Disable DEBUG_GPIO Bjorn Andersson
2017-10-04 18:58 ` [PATCH 4/4] ARM: qcom_defconfig: Enable Z2 Tablet related options Bjorn Andersson
3 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2017-10-04 18:58 UTC (permalink / raw)
To: Andy Gross
Cc: Mark Rutland, devicetree, linux-arm-msm, linux-kernel,
Rob Herring, linux-soc, linux-arm-kernel
CONFIG_HWSPINLOCK must be selected explicitly for SMEM and its
dependencies to be enabled.
The update is generated by "make savedefconfig" and as such reflects
changes to the implicit state of other options, as of v4.14-rc1.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm/configs/qcom_defconfig | 17 +++--------------
1 file changed, 3 insertions(+), 14 deletions(-)
diff --git a/arch/arm/configs/qcom_defconfig b/arch/arm/configs/qcom_defconfig
index 879159e4ab58..82cd86e524a4 100644
--- a/arch/arm/configs/qcom_defconfig
+++ b/arch/arm/configs/qcom_defconfig
@@ -1,5 +1,4 @@
CONFIG_SYSVIPC=y
-CONFIG_FHANDLE=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_IKCONFIG=y
@@ -28,9 +27,7 @@ CONFIG_PCI=y
CONFIG_PCI_MSI=y
CONFIG_PCIE_QCOM=y
CONFIG_SMP=y
-CONFIG_HAVE_ARM_ARCH_TIMER=y
CONFIG_PREEMPT=y
-CONFIG_AEABI=y
CONFIG_HIGHMEM=y
CONFIG_CLEANCACHE=y
CONFIG_ARM_APPENDED_DTB=y
@@ -57,14 +54,12 @@ CONFIG_CFG80211=y
CONFIG_RFKILL=y
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_QCOM_EBI2=y
CONFIG_MTD=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_M25P80=y
CONFIG_MTD_SPI_NOR=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
-CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_SG=y
CONFIG_CHR_DEV_SCH=y
@@ -103,7 +98,6 @@ CONFIG_SERIO_LIBPS2=y
CONFIG_SERIAL_MSM=y
CONFIG_SERIAL_MSM_CONSOLE=y
CONFIG_HW_RANDOM=y
-CONFIG_HW_RANDOM_MSM=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_QUP=y
@@ -123,9 +117,9 @@ CONFIG_PINCTRL_QCOM_SSBI_PMIC=y
CONFIG_GPIOLIB=y
CONFIG_DEBUG_GPIO=y
CONFIG_GPIO_SYSFS=y
-CONFIG_CHARGER_QCOM_SMBB=y
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_MSM=y
+CONFIG_CHARGER_QCOM_SMBB=y
CONFIG_THERMAL=y
CONFIG_QCOM_TSENS=y
CONFIG_MFD_PM8XXX=y
@@ -163,7 +157,6 @@ CONFIG_USB_GADGET_VBUS_DRAW=500
CONFIG_MMC=y
CONFIG_MMC_BLOCK_MINORS=32
CONFIG_MMC_ARMMMCI=y
-CONFIG_MMC_QCOM_DML=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_PLTFM=y
CONFIG_MMC_SDHCI_MSM=y
@@ -173,7 +166,6 @@ CONFIG_LEDS_GPIO=y
CONFIG_LEDS_PM8058=y
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_RPMSG_QCOM_SMD=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_PM8XXX=y
CONFIG_DMADEVICES=y
@@ -187,15 +179,16 @@ CONFIG_IPQ_GCC_4019=y
CONFIG_IPQ_LCC_806X=y
CONFIG_MSM_GCC_8660=y
CONFIG_MSM_LCC_8960=y
-CONFIG_MDM_GCC_9615=y
CONFIG_MDM_LCC_9615=y
CONFIG_MSM_MMCC_8960=y
CONFIG_MSM_MMCC_8974=y
+CONFIG_HWSPINLOCK=y
CONFIG_HWSPINLOCK_QCOM=y
CONFIG_REMOTEPROC=y
CONFIG_QCOM_ADSP_PIL=y
CONFIG_QCOM_Q6V5_PIL=y
CONFIG_QCOM_WCNSS_PIL=y
+CONFIG_RPMSG_QCOM_SMD=y
CONFIG_QCOM_GSBI=y
CONFIG_QCOM_PM=y
CONFIG_QCOM_SMEM=y
@@ -213,7 +206,6 @@ CONFIG_IIO_HRTIMER_TRIGGER=y
CONFIG_BMP280=y
CONFIG_PHY_QCOM_APQ8064_SATA=y
CONFIG_PHY_QCOM_IPQ806X_SATA=y
-CONFIG_NVMEM=y
CONFIG_QCOM_QFPROM=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
@@ -234,7 +226,4 @@ CONFIG_PRINTK_TIME=y
CONFIG_DYNAMIC_DEBUG=y
CONFIG_DEBUG_INFO=y
CONFIG_MAGIC_SYSRQ=y
-CONFIG_LOCKUP_DETECTOR=y
-# CONFIG_DETECT_HUNG_TASK is not set
# CONFIG_SCHED_DEBUG is not set
-CONFIG_TIMER_STATS=y
--
2.12.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 4/4] ARM: qcom_defconfig: Enable Z2 Tablet related options
2017-10-04 18:58 [PATCH 0/4] Sony Xperia Z2 Tablet Initial DTS Bjorn Andersson
` (2 preceding siblings ...)
2017-10-04 18:58 ` [PATCH 3/4] ARM: qcom_defconfig: Disable DEBUG_GPIO Bjorn Andersson
@ 2017-10-04 18:58 ` Bjorn Andersson
3 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2017-10-04 18:58 UTC (permalink / raw)
To: Andy Gross
Cc: Rob Herring, Mark Rutland, devicetree, linux-arm-kernel,
linux-kernel, linux-arm-msm, linux-soc
Select the options necessary to get USB, coincell, WiFI, touchscreen and
backlight on the Z2 Tablet (and other family B devices) working. The
device specific peripherals are selected as modules.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm/configs/qcom_defconfig | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm/configs/qcom_defconfig b/arch/arm/configs/qcom_defconfig
index f6aa100bf69c..d937f2be7c39 100644
--- a/arch/arm/configs/qcom_defconfig
+++ b/arch/arm/configs/qcom_defconfig
@@ -60,6 +60,7 @@ CONFIG_MTD_M25P80=y
CONFIG_MTD_SPI_NOR=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
+CONFIG_QCOM_COINCELL=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_SG=y
CONFIG_CHR_DEV_SCH=y
@@ -82,6 +83,7 @@ CONFIG_SLIP_MODE_SLIP6=y
CONFIG_USB_USBNET=y
# CONFIG_USB_NET_AX8817X is not set
# CONFIG_USB_NET_ZAURUS is not set
+CONFIG_BRCMFMAC=m
CONFIG_INPUT_EVDEV=y
# CONFIG_KEYBOARD_ATKBD is not set
CONFIG_KEYBOARD_GPIO=y
@@ -93,6 +95,10 @@ CONFIG_INPUT_MISC=y
CONFIG_INPUT_PM8XXX_VIBRATOR=y
CONFIG_INPUT_PMIC8XXX_PWRKEY=y
CONFIG_INPUT_UINPUT=y
+CONFIG_RMI4_CORE=m
+CONFIG_RMI4_I2C=m
+CONFIG_RMI4_F11=y
+CONFIG_RMI4_F12=y
CONFIG_SERIO_LIBPS2=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_MSM=y
@@ -128,8 +134,13 @@ CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_QCOM_RPM=y
CONFIG_REGULATOR_QCOM_SMD_RPM=y
+CONFIG_REGULATOR_QCOM_SPMI=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_FB=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_LP855X=m
CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_DYNAMIC_MINORS=y
@@ -148,11 +159,17 @@ CONFIG_USB_ACM=y
CONFIG_USB_CHIPIDEA=y
CONFIG_USB_CHIPIDEA_UDC=y
CONFIG_USB_CHIPIDEA_HOST=y
+CONFIG_USB_CHIPIDEA_ULPI=y
CONFIG_USB_SERIAL=y
CONFIG_USB_MSM_OTG=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DEBUG_FILES=y
CONFIG_USB_GADGET_VBUS_DRAW=500
+CONFIG_USB_CONFIGFS=y
+CONFIG_USB_CONFIGFS_NCM=y
+CONFIG_USB_CONFIGFS_ECM=y
+CONFIG_USB_CONFIGFS_F_FS=y
+CONFIG_USB_ULPI_BUS=y
CONFIG_MMC=y
CONFIG_MMC_BLOCK_MINORS=32
CONFIG_MMC_ARMMMCI=y
@@ -187,6 +204,7 @@ CONFIG_REMOTEPROC=y
CONFIG_QCOM_ADSP_PIL=y
CONFIG_QCOM_Q6V5_PIL=y
CONFIG_QCOM_WCNSS_PIL=y
+CONFIG_RPMSG_CHAR=y
CONFIG_RPMSG_QCOM_SMD=y
CONFIG_QCOM_GSBI=y
CONFIG_QCOM_PM=y
@@ -195,6 +213,7 @@ CONFIG_QCOM_SMD_RPM=y
CONFIG_QCOM_SMP2P=y
CONFIG_QCOM_SMSM=y
CONFIG_QCOM_WCNSS_CTRL=y
+CONFIG_EXTCON_QCOM_SPMI_MISC=y
CONFIG_IIO=y
CONFIG_IIO_BUFFER_CB=y
CONFIG_IIO_SW_TRIGGER=y
@@ -203,8 +222,10 @@ CONFIG_MPU3050_I2C=y
CONFIG_AK8975=y
CONFIG_IIO_HRTIMER_TRIGGER=y
CONFIG_BMP280=y
+CONFIG_PWM=y
CONFIG_PHY_QCOM_APQ8064_SATA=y
CONFIG_PHY_QCOM_IPQ806X_SATA=y
+CONFIG_PHY_QCOM_USB_HS=y
CONFIG_QCOM_QFPROM=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
@@ -226,3 +247,4 @@ CONFIG_DYNAMIC_DEBUG=y
CONFIG_DEBUG_INFO=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_SCHED_DEBUG is not set
+CONFIG_CRYPTO_DRBG_MENU=y
--
2.12.0
^ permalink raw reply related [flat|nested] 6+ messages in thread