[parent not found: <1507891383-15452-1-git-send-email-LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>]
* [PATCH 1/7] ARM: dts: imx6ul-txul: enable I2C bus recovery
[not found] ` <1507891383-15452-1-git-send-email-LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
@ 2017-10-13 10:42 ` Lothar Waßmann
2017-10-13 10:42 ` [PATCH 2/7] ARM: dts: imx6ul-txul: specify ethernet phy reset post-delay Lothar Waßmann
1 sibling, 0 replies; 11+ messages in thread
From: Lothar Waßmann @ 2017-10-13 10:42 UTC (permalink / raw)
To: Fabio Estevam, Mark Rutland, Rob Herring, Russell King,
Sascha Hauer, Shawn Guo, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Lothar Waßmann
Define the required properties to enable I2C bus recovery supported by
the I2C subsystem.
Signed-off-by: Lothar Waßmann <LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
---
arch/arm/boot/dts/imx6ul-tx6ul.dtsi | 14 ++++++++++++--
1 file changed, 12 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
index ec745eb..d30c4e05 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
@@ -1,5 +1,5 @@
/*
- * Copyright 2015 Lothar Waßmann <LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
+ * Copyright 2015-2017 Lothar Waßmann <LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -357,8 +357,11 @@
};
&i2c2 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
clock-frequency = <400000>;
status = "okay";
@@ -817,6 +820,13 @@
>;
};
+ pinctrl_i2c2_gpio: i2c2-gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__GPIO1_IO00 0x4001b0b9
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x4001b0b9
+ >;
+ };
+
pinctrl_kpp: kppgrp {
fsl,pins = <
MX6UL_PAD_ENET2_RX_DATA1__KPP_COL04 0x1b0b0
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 2/7] ARM: dts: imx6ul-txul: specify ethernet phy reset post-delay
[not found] ` <1507891383-15452-1-git-send-email-LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
2017-10-13 10:42 ` [PATCH 1/7] ARM: dts: imx6ul-txul: enable I2C bus recovery Lothar Waßmann
@ 2017-10-13 10:42 ` Lothar Waßmann
1 sibling, 0 replies; 11+ messages in thread
From: Lothar Waßmann @ 2017-10-13 10:42 UTC (permalink / raw)
To: Fabio Estevam, Mark Rutland, Rob Herring, Russell King,
Sascha Hauer, Shawn Guo, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Lothar Waßmann
Under certain circumstances the ethernet PHY cannot be detected on
Ka-Ro electronics TXUL modules. Using a phy-reset-post-delay of > 5ms
alleviates this problem. Specify a value of 10ms to be on the safe side.
Signed-off-by: Lothar Waßmann <LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
---
arch/arm/boot/dts/imx6ul-tx6ul.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
index d30c4e05..9e2a966 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
@@ -308,6 +308,7 @@
pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio &pinctrl_etnphy0_rst>;
phy-mode = "rmii";
phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
+ phy-reset-post-delay = <10>;
phy-supply = <®_3v3_etn>;
phy-handle = <&etnphy0>;
status = "okay";
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 3/7] ARM: dts: imx6ul: add support for TXUL-8013
2017-10-13 10:42 [PATCH 0/7] ARM: dts: imx6ul: Update dts files for the Ka-Ro TXUL module series Lothar Waßmann
[not found] ` <1507891383-15452-1-git-send-email-LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
@ 2017-10-13 10:42 ` Lothar Waßmann
2017-10-13 10:43 ` [PATCH 4/7] ARM: dts: imx6ul-txul: use panel-simple driver for LCD Lothar Waßmann
` (3 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Lothar Waßmann @ 2017-10-13 10:42 UTC (permalink / raw)
To: Fabio Estevam, Mark Rutland, Rob Herring, Russell King,
Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel,
linux-kernel
Cc: Lothar Waßmann
The TXUL-8013 is a Computer On Module manufactured by
Ka-Ro electronics GmbH with the following characteristics:
Processor Freescale i.MX 6ULL MCIMX6Y2, 528 MHz
RAM 256MB 16-bit DDR3 SDRAM
ROM 4GB eMMC
Power supply Single 3.3 to 5V
Size 26mm SO-DIMM
Temp. Range -40°C to 85°C
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/imx6ull-txul-8013.dts | 69 +++++++++++++++++++++++++++++++++
2 files changed, 71 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx6ull-txul-8013.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4b17f35..6d25253 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -475,7 +475,8 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-tx6ul-0010.dtb \
imx6ul-tx6ul-0011.dtb \
imx6ul-tx6ul-mainboard.dtb \
- imx6ull-14x14-evk.dtb
+ imx6ull-14x14-evk.dtb \
+ imx6ull-txul-8013.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-colibri-eval-v3.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-txul-8013.dts b/arch/arm/boot/dts/imx6ull-txul-8013.dts
new file mode 100644
index 0000000..34af49b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-txul-8013.dts
@@ -0,0 +1,69 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ul-tx6ul.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-8013 Module";
+ compatible = "karo,imx6ull-txul", "fsl,imx6ull";
+
+ aliases {
+ /* make eMMC first mmc block device */
+ mmc0 = &usdhc2;
+ mmc1 = &usdhc1;
+ };
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <4>;
+ no-1-8-v;
+ non-removable;
+ fsl,wp-controller;
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 4/7] ARM: dts: imx6ul-txul: use panel-simple driver for LCD
2017-10-13 10:42 [PATCH 0/7] ARM: dts: imx6ul: Update dts files for the Ka-Ro TXUL module series Lothar Waßmann
[not found] ` <1507891383-15452-1-git-send-email-LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
2017-10-13 10:42 ` [PATCH 3/7] ARM: dts: imx6ul: add support for TXUL-8013 Lothar Waßmann
@ 2017-10-13 10:43 ` Lothar Waßmann
[not found] ` <1507891383-15452-5-git-send-email-LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
2017-10-13 10:43 ` [PATCH 5/7] ARM: dts: imx6ul-txul: use interrupts-extended property Lothar Waßmann
` (2 subsequent siblings)
5 siblings, 1 reply; 11+ messages in thread
From: Lothar Waßmann @ 2017-10-13 10:43 UTC (permalink / raw)
To: Fabio Estevam, Mark Rutland, Rob Herring, Russell King,
Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel,
linux-kernel
Cc: Lothar Waßmann
Convert the TXUL board support to use the panel-simple driver.
The now obsolete 'display-timings' node is kept for compatibility with
U-Boot, which derives its display configuration therefrom.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6ul-tx6ul.dtsi | 263 ++++++++++++++++++------------------
1 file changed, 134 insertions(+), 129 deletions(-)
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
index 9e2a966..f8f7685 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
@@ -47,7 +47,7 @@
aliases {
can0 = &can2;
can1 = &can1;
- display = &display;
+ display = &lcdif;
i2c0 = &i2c2;
i2c1 = &i2c_gpio;
i2c2 = &i2c1;
@@ -85,10 +85,10 @@
backlight: backlight {
compatible = "pwm-backlight";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd_rst>;
- enable-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pinctrl_lcd_pwr>;
+ enable-gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
pwms = <&pwm5 0 500000 PWM_POLARITY_INVERTED>;
- power-supply = <®_lcd_pwr>;
+ power-supply = <®_3v3>;
/*
* a poor man's way to create a 1:1 relationship between
* the PWM value and the actual duty cycle
@@ -127,6 +127,22 @@
};
};
+ lcd-panel {
+ compatible = "edt,etm0700g0dh6";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_rst>;
+ enable-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_3v3>;
+ backlight = <&backlight>;
+ bus-format-override = "rgb24";
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -176,19 +192,6 @@
gpio = <&gpio3 5 GPIO_ACTIVE_LOW>;
};
- reg_lcd_pwr: regulator-lcdpwr {
- compatible = "regulator-fixed";
- regulator-name = "LCD POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd_pwr>;
- gpio = <&gpio5 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- regulator-always-on;
- };
-
reg_usbh1_vbus: regulator-usbh1vbus {
compatible = "regulator-fixed";
regulator-name = "usbh1_vbus";
@@ -424,127 +427,129 @@
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_disp0_1>;
- lcd-supply = <®_lcd_pwr>;
- display = <&display>;
status = "okay";
- display: display@di0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
- status = "okay";
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
- display-timings {
- VGA {
- clock-frequency = <25200000>;
- hactive = <640>;
- vactive = <480>;
- hback-porch = <48>;
- hsync-len = <96>;
- hfront-porch = <16>;
- vback-porch = <31>;
- vsync-len = <2>;
- vfront-porch = <12>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
- ETV570 {
- clock-frequency = <25200000>;
- hactive = <640>;
- vactive = <480>;
- hback-porch = <114>;
- hsync-len = <30>;
- hfront-porch = <16>;
- vback-porch = <32>;
- vsync-len = <3>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
+ ETV570 {
+ u-boot,panel-name = "edt,et057090dhu";
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
- ET0350 {
- clock-frequency = <6413760>;
- hactive = <320>;
- vactive = <240>;
- hback-porch = <34>;
- hsync-len = <34>;
- hfront-porch = <20>;
- vback-porch = <15>;
- vsync-len = <3>;
- vfront-porch = <4>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
+ ET0350 {
+ u-boot,panel-name = "edt,et0350g0dh6";
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
- ET0430 {
- clock-frequency = <9009000>;
- hactive = <480>;
- vactive = <272>;
- hback-porch = <2>;
- hsync-len = <41>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vsync-len = <10>;
- vfront-porch = <2>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
+ ET0430 {
+ u-boot,panel-name = "edt,et0430g0dh6";
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
- ET0500 {
- clock-frequency = <33264000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <88>;
- hsync-len = <128>;
- hfront-porch = <40>;
- vback-porch = <33>;
- vsync-len = <2>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
- ET0700 { /* same as ET0500 */
- clock-frequency = <33264000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <88>;
- hsync-len = <128>;
- hfront-porch = <40>;
- vback-porch = <33>;
- vsync-len = <2>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
+ ET0700 { /* same timing as ET0500 */
+ u-boot,panel-name = "edt,etm0700g0dh6";
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
- ETQ570 {
- clock-frequency = <6596040>;
- hactive = <320>;
- vactive = <240>;
- hback-porch = <38>;
- hsync-len = <30>;
- hfront-porch = <30>;
- vback-porch = <16>;
- vsync-len = <3>;
- vfront-porch = <4>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
};
};
};
--
2.1.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 5/7] ARM: dts: imx6ul-txul: use interrupts-extended property
2017-10-13 10:42 [PATCH 0/7] ARM: dts: imx6ul: Update dts files for the Ka-Ro TXUL module series Lothar Waßmann
` (2 preceding siblings ...)
2017-10-13 10:43 ` [PATCH 4/7] ARM: dts: imx6ul-txul: use panel-simple driver for LCD Lothar Waßmann
@ 2017-10-13 10:43 ` Lothar Waßmann
2017-10-13 10:43 ` [PATCH 6/7] ARM: dts: imx6ul: add support for TXUL modules on TXUL-Mainboard Lothar Waßmann
2017-10-13 10:43 ` [PATCH 7/7] ARM: dts: imx6ul-txul: add support for TXUL modules on MB7 baseboard Lothar Waßmann
5 siblings, 0 replies; 11+ messages in thread
From: Lothar Waßmann @ 2017-10-13 10:43 UTC (permalink / raw)
To: Fabio Estevam, Mark Rutland, Rob Herring, Russell King,
Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel,
linux-kernel
Cc: Lothar Waßmann
Use the 'interrupts-extended' property instead of pairs of
'interrupt-parent', 'interrupts' properties.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6ul-tx6ul.dtsi | 12 ++++--------
1 file changed, 4 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
index f8f7685..97c7047 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
@@ -325,8 +325,7 @@
reg = <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_etnphy0_int>;
- interrupt-parent = <&gpio5>;
- interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&gpio5 5 IRQ_TYPE_EDGE_FALLING>;
status = "okay";
};
@@ -335,8 +334,7 @@
reg = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_etnphy1_int>;
- interrupt-parent = <&gpio4>;
- interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&gpio4 27 IRQ_TYPE_EDGE_FALLING>;
status = "okay";
};
};
@@ -383,8 +381,7 @@
reg = <0x38>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_edt_ft5x06>;
- interrupt-parent = <&gpio5>;
- interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_FALLING>;
reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
wake-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
wakeup-source;
@@ -395,8 +392,7 @@
reg = <0x48>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc2007>;
- interrupt-parent = <&gpio3>;
- interrupts = <26 IRQ_TYPE_NONE>;
+ interrupts-extended = <&gpio3 26 IRQ_TYPE_NONE>;
gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
ti,x-plate-ohms = <660>;
wakeup-source;
--
2.1.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 6/7] ARM: dts: imx6ul: add support for TXUL modules on TXUL-Mainboard
2017-10-13 10:42 [PATCH 0/7] ARM: dts: imx6ul: Update dts files for the Ka-Ro TXUL module series Lothar Waßmann
` (3 preceding siblings ...)
2017-10-13 10:43 ` [PATCH 5/7] ARM: dts: imx6ul-txul: use interrupts-extended property Lothar Waßmann
@ 2017-10-13 10:43 ` Lothar Waßmann
[not found] ` <1507891383-15452-7-git-send-email-LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org>
2017-10-13 10:43 ` [PATCH 7/7] ARM: dts: imx6ul-txul: add support for TXUL modules on MB7 baseboard Lothar Waßmann
5 siblings, 1 reply; 11+ messages in thread
From: Lothar Waßmann @ 2017-10-13 10:43 UTC (permalink / raw)
To: Fabio Estevam, Mark Rutland, Rob Herring, Russell King,
Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel,
linux-kernel
Cc: Lothar Waßmann
Add .dts files for the TXUL module variants TXUL-5010, TXUL-5011,
TXUL-8013 on the TXUL-Mainboard.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 6 +-
arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts | 271 ----------------------
arch/arm/boot/dts/imx6ul-txul-5010-mainboard.dts | 48 ++++
arch/arm/boot/dts/imx6ul-txul-5011-mainboard.dts | 48 ++++
arch/arm/boot/dts/imx6ul-txul-mainboard.dtsi | 265 +++++++++++++++++++++
arch/arm/boot/dts/imx6ull-txul-8013-mainboard.dts | 48 ++++
6 files changed, 413 insertions(+), 273 deletions(-)
delete mode 100644 arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul-5010-mainboard.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul-5011-mainboard.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul-mainboard.dtsi
create mode 100644 arch/arm/boot/dts/imx6ull-txul-8013-mainboard.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6d25253..f61cee7 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -474,9 +474,11 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-pico-hobbit.dtb \
imx6ul-tx6ul-0010.dtb \
imx6ul-tx6ul-0011.dtb \
- imx6ul-tx6ul-mainboard.dtb \
+ imx6ul-txul-5010-mainboard.dtb \
+ imx6ul-txul-5011-mainboard.dtb \
imx6ull-14x14-evk.dtb \
- imx6ull-txul-8013.dtb
+ imx6ull-txul-8013.dtb \
+ imx6ull-txul-8013-mainboard.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-colibri-eval-v3.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts b/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
deleted file mode 100644
index 28d055e..0000000
--- a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
+++ /dev/null
@@ -1,271 +0,0 @@
-/*
- * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6ul.dtsi"
-#include "imx6ul-tx6ul.dtsi"
-
-/ {
- model = "Ka-Ro electronics TXUL-0010 Module on TXUL Mainboard";
- compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
-
- aliases {
- lcdif_24bit_pins_a = &pinctrl_disp0_3;
- mmc0 = &usdhc1;
- /delete-property/ mmc1;
- serial2 = &uart3;
- serial4 = &uart5;
- };
- /delete-node/ sound;
-};
-
-&can1 {
- xceiver-supply = <®_3v3>;
-};
-
-&can2 {
- xceiver-supply = <®_3v3>;
-};
-
-&ds1339 {
- status = "disabled";
-};
-
-&fec1 {
- pinctrl-0 = <&pinctrl_enet1 &pinctrl_etnphy0_rst>;
- /delete-node/ mdio;
-};
-
-&fec2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio &pinctrl_etnphy1_rst>;
- phy-mode = "rmii";
- phy-reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
- phy-supply = <®_3v3_etn>;
- phy-handle = <&etnphy1>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- etnphy0: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_etnphy0_int>;
- interrupt-parent = <&gpio5>;
- interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
- interrupts-extended = <&gpio5 5 IRQ_TYPE_EDGE_FALLING>;
- status = "okay";
- };
-
- etnphy1: ethernet-phy@2 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <2>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_etnphy1_int>;
- interrupt-parent = <&gpio4>;
- interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
- interrupts-extended = <&gpio4 27 IRQ_TYPE_EDGE_FALLING>;
- status = "okay";
- };
- };
-};
-
-&i2c_gpio {
- status = "disabled";
-};
-
-&i2c2 {
- /delete-node/ codec@0a;
- /delete-node/ touchscreen@48;
-
- rtc: mcp7940x@6f {
- compatible = "microchip,mcp7940x";
- reg = <0x6f>;
- };
-};
-
-&kpp {
- status = "disabled";
-};
-
-&lcdif {
- pinctrl-0 = <&pinctrl_disp0_3>;
-};
-
-®_usbotg_vbus{
- status = "disabled";
-};
-
-&usdhc1 {
- pinctrl-0 = <&pinctrl_usdhc1>;
- non-removable;
- /delete-property/ cd-gpios;
- cap-sdio-irq;
-};
-
-&uart1 {
- pinctrl-0 = <&pinctrl_uart1>;
- /delete-property/ uart-has-rtscts;
-};
-
-&uart2 {
- pinctrl-0 = <&pinctrl_uart2>;
- /delete-property/ uart-has-rtscts;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&uart6 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart6>;
- status = "okay";
-};
-
-&uart7 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart7>;
- status = "okay";
-};
-
-&uart8 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart8>;
- status = "disabled"; /* conflicts with LCDIF */
-};
-
-&iomuxc {
- hoggrp {
- fsl,pins = <
- MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x0b0b0 /* WLAN_RESET */
- >;
- };
-
- pinctrl_disp0_3: disp0grp-3 {
- fsl,pins = <
- MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
- MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
- MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
- MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
- MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
- MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
- MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
- MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
- MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
- MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
- /* LCD_DATA08..09 not wired */
- MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
- MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
- MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
- MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
- MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
- MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
- /* LCD_DATA16..17 not wired */
- MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
- MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
- MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
- MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
- MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
- MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
- >;
- };
-
- pinctrl_enet2_mdio: enet2-mdiogrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x0b0b0
- MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
- >;
- };
-
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x0b0b0
- MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x0b0b0
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x0b0b0
- MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x0b0b0
- >;
- };
-
- pinctrl_uart6: uart6grp {
- fsl,pins = <
- MX6UL_PAD_CSI_MCLK__UART6_DCE_TX 0x0b0b0
- MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX 0x0b0b0
- >;
- };
-
- pinctrl_uart7: uart7grp {
- fsl,pins = <
- MX6UL_PAD_LCD_DATA16__UART7_DCE_TX 0x0b0b0
- MX6UL_PAD_LCD_DATA17__UART7_DCE_RX 0x0b0b0
- >;
- };
-
- pinctrl_uart8: uart8grp {
- fsl,pins = <
- MX6UL_PAD_LCD_DATA20__UART8_DCE_TX 0x0b0b0
- MX6UL_PAD_LCD_DATA21__UART8_DCE_RX 0x0b0b0
- >;
- };
-};
diff --git a/arch/arm/boot/dts/imx6ul-txul-5010-mainboard.dts b/arch/arm/boot/dts/imx6ul-txul-5010-mainboard.dts
new file mode 100644
index 0000000..b2d3a51
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-5010-mainboard.dts
@@ -0,0 +1,48 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul-tx6ul-0010.dts"
+#include "imx6ul-txul-mainboard.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-5010/-0010 Module on TXUL Mainboard";
+};
diff --git a/arch/arm/boot/dts/imx6ul-txul-5011-mainboard.dts b/arch/arm/boot/dts/imx6ul-txul-5011-mainboard.dts
new file mode 100644
index 0000000..fbdea92
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-5011-mainboard.dts
@@ -0,0 +1,48 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul-tx6ul-0011.dts"
+#include "imx6ul-txul-mainboard.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-5011/-0011 Module on TXUL Mainboard";
+};
diff --git a/arch/arm/boot/dts/imx6ul-txul-mainboard.dtsi b/arch/arm/boot/dts/imx6ul-txul-mainboard.dtsi
new file mode 100644
index 0000000..8bb986f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-mainboard.dtsi
@@ -0,0 +1,265 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ aliases {
+ lcdif_24bit_pins_a = &pinctrl_disp0_3;
+ mmc0 = &usdhc1;
+ /delete-property/ mmc1;
+ serial2 = &uart3;
+ serial4 = &uart5;
+ };
+
+ /delete-node/ sound;
+};
+
+&can1 {
+ xceiver-supply = <®_3v3>;
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&fec1 {
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_etnphy0_rst>;
+ /delete-node/ mdio;
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio &pinctrl_etnphy1_rst>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+ phy-supply = <®_3v3_etn>;
+ phy-handle = <&etnphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ etnphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy0_int>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&gpio5 5 IRQ_TYPE_EDGE_FALLING>;
+ status = "okay";
+ };
+
+ etnphy1: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy1_int>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&gpio4 27 IRQ_TYPE_EDGE_FALLING>;
+ status = "okay";
+ };
+ };
+};
+
+&i2c_gpio {
+ status = "disabled";
+};
+
+&i2c2 {
+ /delete-node/ codec@0a;
+ /delete-node/ touchscreen@48;
+
+ rtc: mcp7940x@6f {
+ compatible = "microchip,mcp7940x";
+ reg = <0x6f>;
+ };
+};
+
+&kpp {
+ status = "disabled";
+};
+
+&lcdif {
+ pinctrl-0 = <&pinctrl_disp0_3>;
+};
+
+®_usbotg_vbus {
+ status = "disabled";
+};
+
+&usdhc1 {
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ /delete-property/ cd-gpios;
+ cap-sdio-irq;
+};
+
+&uart1 {
+ pinctrl-0 = <&pinctrl_uart1>;
+ /delete-property/ uart-has-rtscts;
+};
+
+&uart2 {
+ pinctrl-0 = <&pinctrl_uart2>;
+ /delete-property/ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart6>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart7>;
+ status = "okay";
+};
+
+&uart8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart8>;
+ status = "disabled"; /* conflicts with LCDIF */
+};
+
+&iomuxc {
+ hoggrp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x0b0b0 /* WLAN_RESET */
+ >;
+ };
+
+ pinctrl_disp0_3: disp0grp-3 {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
+ /* LCD_DATA08..09 not wired */
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
+ /* LCD_DATA16..17 not wired */
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
+ >;
+ };
+
+ pinctrl_enet2_mdio: enet2-mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x0b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart6: uart6grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__UART6_DCE_TX 0x0b0b0
+ MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart7: uart7grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA16__UART7_DCE_TX 0x0b0b0
+ MX6UL_PAD_LCD_DATA17__UART7_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart8: uart8grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA20__UART8_DCE_TX 0x0b0b0
+ MX6UL_PAD_LCD_DATA21__UART8_DCE_RX 0x0b0b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ull-txul-8013-mainboard.dts b/arch/arm/boot/dts/imx6ull-txul-8013-mainboard.dts
new file mode 100644
index 0000000..34d42e5
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-txul-8013-mainboard.dts
@@ -0,0 +1,48 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ull-txul-8013.dts"
+#include "imx6ul-txul-mainboard.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-8013 Module on TXUL Mainboard";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 7/7] ARM: dts: imx6ul-txul: add support for TXUL modules on MB7 baseboard
2017-10-13 10:42 [PATCH 0/7] ARM: dts: imx6ul: Update dts files for the Ka-Ro TXUL module series Lothar Waßmann
` (4 preceding siblings ...)
2017-10-13 10:43 ` [PATCH 6/7] ARM: dts: imx6ul: add support for TXUL modules on TXUL-Mainboard Lothar Waßmann
@ 2017-10-13 10:43 ` Lothar Waßmann
5 siblings, 0 replies; 11+ messages in thread
From: Lothar Waßmann @ 2017-10-13 10:43 UTC (permalink / raw)
To: Fabio Estevam, Mark Rutland, Rob Herring, Russell King,
Sascha Hauer, Shawn Guo, devicetree, linux-arm-kernel,
linux-kernel
Cc: Lothar Waßmann
Add a dtsi file for TXUL modules on the MB7 baseboard and use it to
create dts files for the various TXUL module variants on the MB7
baseboard.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 5 +-
arch/arm/boot/dts/imx6ul-txul-5010-mb7.dts | 48 +++++++++++++++++++
arch/arm/boot/dts/imx6ul-txul-5011-mb7.dts | 48 +++++++++++++++++++
arch/arm/boot/dts/imx6ul-txul-mb7.dtsi | 74 +++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6ull-txul-8013-mb7.dts | 48 +++++++++++++++++++
5 files changed, 222 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx6ul-txul-5010-mb7.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul-5011-mb7.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul-mb7.dtsi
create mode 100644 arch/arm/boot/dts/imx6ull-txul-8013-mb7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f61cee7..b7fc301 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -475,10 +475,13 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-tx6ul-0010.dtb \
imx6ul-tx6ul-0011.dtb \
imx6ul-txul-5010-mainboard.dtb \
+ imx6ul-txul-5010-mb7.dtb \
imx6ul-txul-5011-mainboard.dtb \
+ imx6ul-txul-5011-mb7.dtb \
imx6ull-14x14-evk.dtb \
imx6ull-txul-8013.dtb \
- imx6ull-txul-8013-mainboard.dtb
+ imx6ull-txul-8013-mainboard.dtb \
+ imx6ull-txul-8013-mb7.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-colibri-eval-v3.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-txul-5010-mb7.dts b/arch/arm/boot/dts/imx6ul-txul-5010-mb7.dts
new file mode 100644
index 0000000..73c5e8f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-5010-mb7.dts
@@ -0,0 +1,48 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul-tx6ul-0010.dts"
+#include "imx6ul-txul-mb7.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-5010/-0010 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/imx6ul-txul-5011-mb7.dts b/arch/arm/boot/dts/imx6ul-txul-5011-mb7.dts
new file mode 100644
index 0000000..cf325f1
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-5011-mb7.dts
@@ -0,0 +1,48 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul-tx6ul-0011.dts"
+#include "imx6ul-txul-mb7.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-5011/-0011 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/imx6ul-txul-mb7.dtsi b/arch/arm/boot/dts/imx6ul-txul-mb7.dtsi
new file mode 100644
index 0000000..7771c6b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-mb7.dtsi
@@ -0,0 +1,74 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ lcd-panel {
+ compatible = "edt,et057090dhu";
+ bus-format-override = "rgb24";
+ pixelclk-active = <0>;
+ };
+
+ /delete-node/ sound;
+};
+
+&can1 {
+ status = "disabled";
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&i2c2 {
+ rtc: mcp7940x@6f {
+ compatible = "microchip,mcp7940x";
+ reg = <0x6f>;
+ };
+};
+
+&sgtl5000 {
+ /*
+ * The SGTL5000 present on the MB7 baseboard cannot be used
+ * because the JTAG interface shares the SAI interface pins.
+ * Especially JTAG_TDI drives the SAI BITCLK via a level shifter.
+ */
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6ull-txul-8013-mb7.dts b/arch/arm/boot/dts/imx6ull-txul-8013-mb7.dts
new file mode 100644
index 0000000..0f16809
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-txul-8013-mb7.dts
@@ -0,0 +1,48 @@
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ull-txul-8013.dts"
+#include "imx6ul-txul-mb7.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-8013 Module on MB7 baseboard";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 11+ messages in thread