From mboxrd@z Thu Jan 1 00:00:00 1970 From: Corentin Labbe Subject: [PATCH v9 04/10] arm: dts: sunxi: h3/h5: represent the mdio switch used by sun8i-h3-emac Date: Tue, 24 Oct 2017 19:57:08 +0200 Message-ID: <20171024175714.15840-5-clabbe.montjoie@gmail.com> References: <20171024175714.15840-1-clabbe.montjoie@gmail.com> Return-path: In-Reply-To: <20171024175714.15840-1-clabbe.montjoie@gmail.com> Sender: linux-kernel-owner@vger.kernel.org To: robh+dt@kernel.org, mark.rutland@arm.com, maxime.ripard@free-electrons.com, wens@csie.org, linux@armlinux.org.uk, catalin.marinas@arm.com, will.deacon@arm.com, peppe.cavallaro@st.com, alexandre.torgue@st.com, andrew@lunn.ch, f.fainelli@gmail.com Cc: netdev@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, Corentin Labbe List-Id: devicetree@vger.kernel.org Since dwmac-sun8i could use either an integrated PHY or an external PHY (which could be at same MDIO address), we need to represent this selection by a MDIO switch. Signed-off-by: Corentin Labbe --- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 32 +++++++++++++++++++++++++++----- 1 file changed, 27 insertions(+), 5 deletions(-) diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index d762098fc589..0e97df490aba 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -422,14 +422,36 @@ #size-cells = <0>; status = "disabled"; - mdio: mdio { + mdio0: mdio { #address-cells = <1>; #size-cells = <0>; - int_mii_phy: ethernet-phy@1 { - compatible = "ethernet-phy-ieee802.3-c22"; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + mdio-parent-bus = <&mdio0>; + /* Only one MDIO is usable at the time */ + internal_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; reg = <1>; - clocks = <&ccu CLK_BUS_EPHY>; - resets = <&ccu RST_BUS_EPHY>; + #address-cells = <1>; + #size-cells = <0>; + + int_mii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + }; + }; + + external_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; }; }; }; -- 2.13.6