[PATCH v3 3/3] DT: leds: Add Qualcomm Light Pulse Generator binding

[Bjorn Andersson <bjorn.andersson@linaro.org>]

This adds the binding document describing the three hardware blocks
related to the Light Pulse Generator found in a wide range of Qualcomm
PMICs.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v2:
- Squashed all things into one node
- Removed quirks from the binding, compatible implies number of channels, their
  configuration etc.
- Binding describes LEDs connected as child nodes
- Support describing multi-channel LEDs
- Change style of the binding document, to match other LED bindings

Changes since v1:
- Dropped custom pattern properties
- Renamed cell-index to qcom,lpg-channel to clarify its purpose

 .../devicetree/bindings/leds/leds-qcom-lpg.txt     | 66 ++++++++++++++++++++++
 1 file changed, 66 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-qcom-lpg.txt

diff --git a/Documentation/devicetree/bindings/leds/leds-qcom-lpg.txt b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.txt
new file mode 100644
index 000000000000..9cee6f9f543c
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.txt
@@ -0,0 +1,66 @@
+Binding for Qualcomm Light Pulse Generator
+
+The Qualcomm Light Pulse Generator consists of three different hardware blocks;
+a ramp generator with lookup table, the light pulse generator and a three
+channel current sink. These blocks are found in a wide range of Qualcomm PMICs.
+
+Required properties:
+- compatible: one of:
+	      "qcom,pm8916-pwm",
+	      "qcom,pm8941-lpg",
+	      "qcom,pm8994-lpg",
+	      "qcom,pmi8994-lpg",
+	      "qcom,pmi8998-lpg",
+
+Optional properties:
+- qcom,power-source: power-source used to drive the output, as defined in the
+		     datasheet. Should be specified if the TRILED block is
+		     present
+- qcom,dtest: configures the output into an internal test line of the
+	      pmic. Specified by a list of u32 pairs, one pair per channel,
+	      where each pair denotes the test line to drive and the second
+	      configures how the value should be outputed, as defined in the
+	      datasheet
+- #pwm-cells: should be 2, see ../pwm/pwm.txt
+
+LED subnodes:
+A set of subnodes can be used to specify LEDs connected to the LPG. Channels
+not associated with a LED are available as pwm channels, see ../pwm/pwm.txt.
+
+Required properties:
+- led-sources: list of channels associated with this LED, starting at 1 for the
+	       first LPG channel
+
+Optional properties:
+- label: see Documentation/devicetree/bindings/leds/common.txt
+- default-state: see Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+The following example defines a RGB LED attached to the PM8941.
+
+&spmi_bus {
+	pm8941@1 {
+		lpg {
+			compatible = "qcom,pm8941-lpg";
+			qcom,power-source = <1>;
+
+			rgb {
+				led-sources = <7 6 5>;
+			};
+		};
+	};
+};
+
+The following example defines the single PWM channel of the PM8916, which can
+be muxed by the MPP4 as a current sink.
+
+&spmi_bus {
+	pm8916@1 {
+		pm8916_pwm: pwm {
+			compatible = "qcom,pm8916-pwm";
+
+			#pwm-cells = <2>;
+		};
+	};
+};
-- 
2.15.0