[PATCH] ARM: dts: introduce the sama5d2 ptc ek board

Ludovic Desroches
2017-12-05T14:23:12Z

Add the official SAMA5D2 Peripheral Touch Controller Evaluation
Kit board.

Signed-off-by: Ludovic Desroches <ludovic.desroches-UWL1GkI3JZL3oGB3hsPCZA@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 442 ++++++++++++++++++++++++++++++
2 files changed, 443 insertions(+)
create mode 100644 arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 043d7c720d0c..ed60582eb1da 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d27_som1_ek.dtb \
+ at91-sama5d2_ptc_ek.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
at91-tse850-3.dtb \
diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
new file mode 100644
index 000000000000..46e8bb668546
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
@@ -0,0 +1,442 @@
+/*
+ * at91-sama5d2_ptc_ek.dts - Device Tree file for SAMA5D2 PTC EK board
+ *
+ * Copyright (C) 2017 Microchip/Atmel,
+ * 2017 Wenyou Yang <wenyou.yang-UWL1GkI3JZL3oGB3hsPCZA@public.gmane.org>
+ * 2017 Ludovic Desroches <ludovic.desroches-UWL1GkI3JZL3oGB3hsPCZA@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Atmel SAMA5D2 PTC EK";
+ compatible = "atmel,sama5d2-ptc_ek", "atmel,sama5d2", "atmel,sama5";
+
+ aliases {
+ serial0 = &uart0;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x20000000 0x80000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <24000000>;
+ };
+ };
+
+ ahb {
+ usb0: gadget@300000 {
+ atmel,vbus-gpio = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci@400000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioA PIN_PB12 GPIO_ACTIVE_HIGH
+ 0
+ >;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+ };
+
+ usb2: ehci@500000 {
+ status = "okay";
+ };
+
+ ebi: ebi@10000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand_default>;
+ status = "okay"; /* conflicts with sdmmc1 and qspi0 */
+
+ nand_controller: nand-controller {
+ status = "okay";
+
+ nand@3 {
+ reg = <0x3 0x0 0x2>;
+ atmel,rb = <0>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ at91bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader@40000 {
+ label = "bootloader";
+ reg = <0x40000 0xc0000>;
+ };
+
+ bootloaderenv@0x100000 {
+ label = "bootloader env";
+ reg = <0x100000 0x40000>;
+ };
+
+ bootloaderenvred@0x140000 {
+ label = "bootloader env redundant";
+ reg = <0x140000 0x40000>;
+ };
+
+ dtb@180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x1f800000>;
+ };
+ };
+ };
+ };
+ };
+
+ sdmmc0: sdio-host@a0000000 {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ non-removable;
+ mmc-ddr-1_8v;
+ status = "okay";
+ };
+
+ apb {
+ spi0: spi@f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_default>;
+ status = "okay";
+ };
+
+ macb0: ethernet@f8008000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+ phy-mode = "rmii";
+ status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioA>;
+ interrupts = <56 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+
+ uart0: serial@f801c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+
+ uart2: serial@f8024000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+
+ i2c0: i2c@f8028000 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ status = "okay";
+ };
+
+ flx0: flexcom@f8034000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+
+ i2c2: i2c@600 {
+ compatible = "atmel,sama5d2-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <0>, <0>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx0_clk>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ atmel,fifo-size = <16>;
+ status = "okay";
+ };
+ };
+
+ shdwc@f8048010 {
+ atmel,shdwc-debouncer = <976>;
+
+ input@0 {
+ reg = <0>;
+ atmel,wakeup-type = "low";
+ };
+ };
+
+ watchdog@f8048040 {
+ status = "okay";
+ };
+
+ spi1: spi@fc000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+ status = "okay";
+ };
+
+ i2c1: i2c@fc028000 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ status = "okay";
+
+ at24@50 {
+ compatible = "24c02";
+ reg = <0x50>;
+ pagesize = <8>;
+ };
+ };
+
+ pinctrl@fc038000 {
+ pinctrl_flx0_default: flx0_default {
+ pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+ <PIN_PB29__FLEXCOM0_IO1>;
+ bias-disable;
+ };
+
+ pinctrl_i2c0_default: i2c0_default {
+ pinmux = <PIN_PD21__TWD0>,
+ <PIN_PD22__TWCK0>;
+ bias-disable;
+ };
+
+ pinctrl_i2c1_default: i2c1_default {
+ pinmux = <PIN_PC6__TWD1>,
+ <PIN_PC7__TWCK1>;
+ bias-disable;
+ };
+
+ pinctrl_key_gpio_default: key_gpio_default {
+ pinmux = <PIN_PA10__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_led_gpio_default: led_gpio_default {
+ pinmux = <PIN_PB6__GPIO>,
+ <PIN_PB8__GPIO>,
+ <PIN_PB10__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_macb0_default: macb0_default {
+ pinmux = <PIN_PB14__GTXCK>,
+ <PIN_PB15__GTXEN>,
+ <PIN_PB16__GRXDV>,
+ <PIN_PB17__GRXER>,
+ <PIN_PB18__GRX0>,
+ <PIN_PB19__GRX1>,
+ <PIN_PB20__GTX0>,
+ <PIN_PB21__GTX1>,
+ <PIN_PB22__GMDC>,
+ <PIN_PB23__GMDIO>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ pinmux = <PIN_PB24__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_nand_default: nand_default {
+ re_we_data {
+ pinmux = <PIN_PA22__D0>,
+ <PIN_PA23__D1>,
+ <PIN_PA24__D2>,
+ <PIN_PA25__D3>,
+ <PIN_PA26__D4>,
+ <PIN_PA27__D5>,
+ <PIN_PA28__D6>,
+ <PIN_PA29__D7>,
+ <PIN_PA30__NWE_NANDWE>,
+ <PIN_PB2__NRD_NANDOE>;
+ bias-pull-up;
+ };
+
+ ale_cle_rdy_cs {
+ pinmux = <PIN_PB0__A21_NANDALE>,
+ <PIN_PB1__A22_NANDCLE>,
+ <PIN_PC8__NANDRDY>,
+ <PIN_PA31__NCS3>;
+ bias-pull-up;
+ };
+ };
+
+ pinctrl_sdmmc0_default: sdmmc0_default {
+ cmd_data {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>,
+ <PIN_PA6__SDMMC0_DAT4>,
+ <PIN_PA7__SDMMC0_DAT5>,
+ <PIN_PA8__SDMMC0_DAT6>,
+ <PIN_PA9__SDMMC0_DAT7>;
+ bias-pull-up;
+ };
+
+ ck_cd_vddsel {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA11__SDMMC0_VDDSEL>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_spi0_default: spi0_default {
+ pinmux = <PIN_PA14__SPI0_SPCK>,
+ <PIN_PA15__SPI0_MOSI>,
+ <PIN_PA16__SPI0_MISO>,
+ <PIN_PA17__SPI0_NPCS0>;
+ bias-disable;
+ };
+
+ pinctrl_spi1_default: spi1_default {
+ pinmux = <PIN_PC1__SPI1_SPCK>,
+ <PIN_PC2__SPI1_MOSI>,
+ <PIN_PC3__SPI1_MISO>,
+ <PIN_PC4__SPI1_NPCS0>;
+ bias-disable;
+ };
+
+ pinctrl_uart0_default: uart0_default {
+ pinmux = <PIN_PB26__URXD0>,
+ <PIN_PB27__UTXD0>;
+ bias-disable;
+ };
+
+ pinctrl_uart2_default: uart2_default {
+ pinmux = <PIN_PD23__URXD2>,
+ <PIN_PD24__UTXD2>;
+ bias-disable;
+ };
+
+ pinctrl_usb_default: usb_default {
+ pinmux = <PIN_PB12__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ pinmux = <PIN_PB11__GPIO>;
+ bias-disable;
+ };
+
+ };
+
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+ bp1 {
+ label = "PB_USER";
+ gpios = <&pioA PIN_PA10 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_gpio_default>;
+ status = "okay";
+
+ red {
+ label = "red";
+ gpios = <&pioA PIN_PB10 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "green";
+ gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "blue";
+ gpios = <&pioA PIN_PB6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
--
2.12.2