From: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
To: Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Cc: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>,
Corentin Labbe
<clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org
Subject: [PATCH 2/2] ARM: dts: sun8i: a83t: Enable Ethernet on two boards
Date: Fri, 8 Dec 2017 15:31:57 +0800 [thread overview]
Message-ID: <20171208073157.14599-3-wens@csie.org> (raw)
In-Reply-To: <20171208073157.14599-1-wens-jdAy2FN1RRM@public.gmane.org>
The Cubietruck Plus has a Realtek RTL8211E RGMII PHY tied to the EMAC.
The AXP818 PMIC's regulators provide main power and secondary signaling
voltages to the PHY. The latter is always on, as it also supplies the
pingroup on the SoC, which has other uses.
The Bananapi M3 has a Realtek RTL8211E RGMII PHY tied to the EMAC.
The AXP818 PMIC's SW regulators provides power to the PHY.
This patch enables Ethernet with the EMAC on both these boards by
enabling the emac node and setting all the required properties.
A proper ethernet alias is added as well.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 19 +++++++++++++++++++
arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts | 17 +++++++++++++++++
2 files changed, 36 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
index c606af3dbfed..6550bf0e594b 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -52,6 +52,7 @@
compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -88,6 +89,24 @@
/* TODO GL830 USB-to-SATA bridge downstream w/ GPIO power controls */
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_sw>;
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii";
+ allwinner,rx-delay-ps = <700>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&mdio {
+ rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
index 7f0a3f6d0cf2..6da08cd0e107 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -52,6 +52,7 @@
compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -154,6 +155,22 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_dldo4>;
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&mdio {
+ rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
--
2.15.0
next prev parent reply other threads:[~2017-12-08 7:31 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-08 7:31 [PATCH 0/2] ARM: sun8i: a83t: Enable EMAC Ethernet Chen-Yu Tsai
[not found] ` <20171208073157.14599-1-wens-jdAy2FN1RRM@public.gmane.org>
2017-12-08 7:31 ` [PATCH 1/2] ARM: dts: sun8i: a83t: add dwmac-sun8i device node Chen-Yu Tsai
2017-12-08 7:31 ` Chen-Yu Tsai [this message]
2017-12-08 9:06 ` [PATCH 0/2] ARM: sun8i: a83t: Enable EMAC Ethernet Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171208073157.14599-3-wens@csie.org \
--to=wens-jday2fn1rrm@public.gmane.org \
--cc=clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org \
--cc=maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).