From: Bartosz Golaszewski <brgl-ARrdPY/1zhM@public.gmane.org>
To: Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>,
Linus Walleij
<linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>,
Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Bartosz Golaszewski <brgl-ARrdPY/1zhM@public.gmane.org>
Subject: [PATCH 2/2] eeprom: at24: add support for the write-protect pin
Date: Tue, 19 Dec 2017 17:14:32 +0100 [thread overview]
Message-ID: <20171219161432.29809-3-brgl@bgdev.pl> (raw)
In-Reply-To: <20171219161432.29809-1-brgl-ARrdPY/1zhM@public.gmane.org>
AT24 EEPROMs have a write-protect pin, which - when pulled high -
inhibits writes to the upper quadrant of memory (although it has been
observed that on some chips it disables writing to the entire memory
range).
On some boards, this pin is connected to a GPIO and pulled high by
default, which forces the user to manually change its state before
writing. On linux this means that we either need to hog the line all
the time, or set the GPIO value before writing from outside of the
at24 driver.
Make the driver check if the write-protect GPIO was defined in the
device tree and pull it low whenever writing to the EEPROM.
Signed-off-by: Bartosz Golaszewski <brgl-ARrdPY/1zhM@public.gmane.org>
---
drivers/misc/eeprom/at24.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/drivers/misc/eeprom/at24.c b/drivers/misc/eeprom/at24.c
index b44a3d2b2b20..8cb0883dd297 100644
--- a/drivers/misc/eeprom/at24.c
+++ b/drivers/misc/eeprom/at24.c
@@ -27,6 +27,7 @@
#include <linux/regmap.h>
#include <linux/platform_data/at24.h>
#include <linux/pm_runtime.h>
+#include <linux/gpio/consumer.h>
/*
* I2C EEPROMs from most vendors are inexpensive and mostly interchangeable.
@@ -77,6 +78,8 @@ struct at24_data {
struct nvmem_config nvmem_config;
struct nvmem_device *nvmem;
+ struct gpio_desc *wp_gpio;
+
/*
* Some chips tie up multiple I2C addresses; dummy devices reserve
* them for us, and we'll use them with SMBus calls.
@@ -442,12 +445,14 @@ static int at24_write(void *priv, unsigned int off, void *val, size_t count)
* from this host, but not from other I2C masters.
*/
mutex_lock(&at24->lock);
+ gpiod_set_value_cansleep(at24->wp_gpio, 0);
while (count) {
int status;
status = at24_regmap_write(at24, buf, off, count);
if (status < 0) {
+ gpiod_set_value_cansleep(at24->wp_gpio, 1);
mutex_unlock(&at24->lock);
pm_runtime_put(dev);
return status;
@@ -457,6 +462,7 @@ static int at24_write(void *priv, unsigned int off, void *val, size_t count)
count -= status;
}
+ gpiod_set_value_cansleep(at24->wp_gpio, 1);
mutex_unlock(&at24->lock);
pm_runtime_put(dev);
@@ -604,6 +610,12 @@ static int at24_probe(struct i2c_client *client, const struct i2c_device_id *id)
at24->num_addresses = num_addresses;
at24->offset_adj = at24_get_offset_adj(chip.flags, chip.byte_len);
+ at24->wp_gpio = devm_gpiod_get_optional(&client->dev,
+ "write-protect",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(at24->wp_gpio))
+ return PTR_ERR(at24->wp_gpio);
+
at24->client[0].client = client;
at24->client[0].regmap = devm_regmap_init_i2c(client, ®map_config);
if (IS_ERR(at24->client[0].regmap))
--
2.15.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2017-12-19 16:14 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-19 16:14 [PATCH 0/2] eeprom: at24: write-protect pin support Bartosz Golaszewski
[not found] ` <20171219161432.29809-1-brgl-ARrdPY/1zhM@public.gmane.org>
2017-12-19 16:14 ` [PATCH 1/2] dt-bindings: at24: new optional property - write-protect-gpios Bartosz Golaszewski
2017-12-19 22:25 ` Andy Shevchenko
2017-12-19 16:14 ` Bartosz Golaszewski [this message]
2017-12-20 8:27 ` [PATCH 0/2] eeprom: at24: write-protect pin support Bartosz Golaszewski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171219161432.29809-3-brgl@bgdev.pl \
--to=brgl-arrdpy/1zhm@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).