* [PATCH V3 1/2] ARM: dts: imx6ul: add 696MHz operating point @ 2018-01-08 2:04 Anson Huang 2018-01-08 2:04 ` [PATCH V3 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul Anson Huang 0 siblings, 1 reply; 4+ messages in thread From: Anson Huang @ 2018-01-08 2:04 UTC (permalink / raw) To: shawnguo, kernel, fabio.estevam, robh+dt, mark.rutland, linux, rjw, viresh.kumar Cc: linux-arm-kernel, devicetree, linux-kernel, linux-pm Add 696MHz operating point according to datasheet (Rev. 0, 12/2015). Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> --- changes since v2: add reviewed-by. arch/arm/boot/dts/imx6ul.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi index d5181f8..963e169 100644 --- a/arch/arm/boot/dts/imx6ul.dtsi +++ b/arch/arm/boot/dts/imx6ul.dtsi @@ -68,12 +68,14 @@ clock-latency = <61036>; /* two CLK32 periods */ operating-points = < /* kHz uV */ + 696000 1275000 528000 1175000 396000 1025000 198000 950000 >; fsl,soc-operating-points = < /* KHz uV */ + 696000 1275000 528000 1175000 396000 1175000 198000 1175000 -- 1.9.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH V3 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul 2018-01-08 2:04 [PATCH V3 1/2] ARM: dts: imx6ul: add 696MHz operating point Anson Huang @ 2018-01-08 2:04 ` Anson Huang 2018-01-08 3:43 ` Viresh Kumar 2018-01-09 10:27 ` Dong Aisheng 0 siblings, 2 replies; 4+ messages in thread From: Anson Huang @ 2018-01-08 2:04 UTC (permalink / raw) To: shawnguo, kernel, fabio.estevam, robh+dt, mark.rutland, linux, rjw, viresh.kumar Cc: linux-arm-kernel, devicetree, linux-kernel, linux-pm Add 696MHz operating point for i.MX6UL, only for those parts with speed grading fuse set to 2b'10 supports 696MHz operating point, so, speed grading check is also added for i.MX6UL in this patch, the clock tree for each operating point are as below: 696MHz: pll1 696000000 pll1_bypass 696000000 pll1_sys 696000000 pll1_sw 696000000 arm 696000000 528MHz: pll2 528000000 pll2_bypass 528000000 pll2_bus 528000000 ca7_secondary_sel 528000000 step 528000000 pll1_sw 528000000 arm 528000000 396MHz: pll2_pfd2_396m 396000000 ca7_secondary_sel 396000000 step 396000000 pll1_sw 396000000 arm 396000000 198MHz: pll2_pfd2_396m 396000000 ca7_secondary_sel 396000000 step 396000000 pll1_sw 396000000 arm 198000000 Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> --- changes since v2: add reviewed-by. drivers/cpufreq/imx6q-cpufreq.c | 46 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 45 insertions(+), 1 deletion(-) diff --git a/drivers/cpufreq/imx6q-cpufreq.c b/drivers/cpufreq/imx6q-cpufreq.c index 8bfb077..741f22e 100644 --- a/drivers/cpufreq/imx6q-cpufreq.c +++ b/drivers/cpufreq/imx6q-cpufreq.c @@ -136,6 +136,10 @@ static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index) clks[PLL2_PFD2_396M].clk); clk_set_parent(clks[STEP].clk, clks[SECONDARY_SEL].clk); clk_set_parent(clks[PLL1_SW].clk, clks[STEP].clk); + if (freq_hz > clk_get_rate(clks[PLL2_BUS].clk)) { + clk_set_rate(clks[PLL1_SYS].clk, new_freq * 1000); + clk_set_parent(clks[PLL1_SW].clk, clks[PLL1_SYS].clk); + } } else { clk_set_parent(clks[STEP].clk, clks[PLL2_PFD2_396M].clk); clk_set_parent(clks[PLL1_SW].clk, clks[STEP].clk); @@ -260,6 +264,43 @@ static void imx6q_opp_check_speed_grading(struct device *dev) of_node_put(np); } +#define OCOTP_CFG3_6UL_SPEED_696MHZ 0x2 + +static void imx6ul_opp_check_speed_grading(struct device *dev) +{ + struct device_node *np; + void __iomem *base; + u32 val; + + np = of_find_compatible_node(NULL, NULL, "fsl,imx6ul-ocotp"); + if (!np) + return; + + base = of_iomap(np, 0); + if (!base) { + dev_err(dev, "failed to map ocotp\n"); + goto put_node; + } + + /* + * Speed GRADING[1:0] defines the max speed of ARM: + * 2b'00: Reserved; + * 2b'01: 528000000Hz; + * 2b'10: 696000000Hz; + * 2b'11: Reserved; + * We need to set the max speed of ARM according to fuse map. + */ + val = readl_relaxed(base + OCOTP_CFG3); + val >>= OCOTP_CFG3_SPEED_SHIFT; + val &= 0x3; + if (val != OCOTP_CFG3_6UL_SPEED_696MHZ) + if (dev_pm_opp_disable(dev, 696000000)) + dev_warn(dev, "failed to disable 696MHz OPP\n"); + iounmap(base); +put_node: + of_node_put(np); +} + static int imx6q_cpufreq_probe(struct platform_device *pdev) { struct device_node *np; @@ -314,7 +355,10 @@ static int imx6q_cpufreq_probe(struct platform_device *pdev) goto put_reg; } - imx6q_opp_check_speed_grading(cpu_dev); + if (of_machine_is_compatible("fsl,imx6ul")) + imx6ul_opp_check_speed_grading(cpu_dev); + else + imx6q_opp_check_speed_grading(cpu_dev); /* Because we have added the OPPs here, we must free them */ free_opp = true; -- 1.9.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH V3 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul 2018-01-08 2:04 ` [PATCH V3 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul Anson Huang @ 2018-01-08 3:43 ` Viresh Kumar 2018-01-09 10:27 ` Dong Aisheng 1 sibling, 0 replies; 4+ messages in thread From: Viresh Kumar @ 2018-01-08 3:43 UTC (permalink / raw) To: Anson Huang Cc: shawnguo, kernel, fabio.estevam, robh+dt, mark.rutland, linux, rjw, linux-arm-kernel, devicetree, linux-kernel, linux-pm On 08-01-18, 10:04, Anson Huang wrote: > Add 696MHz operating point for i.MX6UL, only for those > parts with speed grading fuse set to 2b'10 supports > 696MHz operating point, so, speed grading check is also > added for i.MX6UL in this patch, the clock tree for each > operating point are as below: > > 696MHz: > pll1 696000000 > pll1_bypass 696000000 > pll1_sys 696000000 > pll1_sw 696000000 > arm 696000000 > 528MHz: > pll2 528000000 > pll2_bypass 528000000 > pll2_bus 528000000 > ca7_secondary_sel 528000000 > step 528000000 > pll1_sw 528000000 > arm 528000000 > 396MHz: > pll2_pfd2_396m 396000000 > ca7_secondary_sel 396000000 > step 396000000 > pll1_sw 396000000 > arm 396000000 > 198MHz: > pll2_pfd2_396m 396000000 > ca7_secondary_sel 396000000 > step 396000000 > pll1_sw 396000000 > arm 198000000 > > Signed-off-by: Anson Huang <Anson.Huang@nxp.com> > Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> > --- > changes since v2: > add reviewed-by. > drivers/cpufreq/imx6q-cpufreq.c | 46 ++++++++++++++++++++++++++++++++++++++++- > 1 file changed, 45 insertions(+), 1 deletion(-) Acked-by: Viresh Kumar <viresh.kumar@linaro.org> -- viresh ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH V3 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul 2018-01-08 2:04 ` [PATCH V3 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul Anson Huang 2018-01-08 3:43 ` Viresh Kumar @ 2018-01-09 10:27 ` Dong Aisheng 1 sibling, 0 replies; 4+ messages in thread From: Dong Aisheng @ 2018-01-09 10:27 UTC (permalink / raw) To: Anson Huang Cc: shawnguo, kernel, fabio.estevam, robh+dt, mark.rutland, linux, rjw, viresh.kumar, linux-arm-kernel, devicetree, linux-kernel, linux-pm, linux-imx On Mon, Jan 08, 2018 at 10:04:51AM +0800, Anson Huang wrote: > Add 696MHz operating point for i.MX6UL, only for those > parts with speed grading fuse set to 2b'10 supports > 696MHz operating point, so, speed grading check is also > added for i.MX6UL in this patch, the clock tree for each > operating point are as below: > > 696MHz: > pll1 696000000 > pll1_bypass 696000000 > pll1_sys 696000000 > pll1_sw 696000000 > arm 696000000 > 528MHz: > pll2 528000000 > pll2_bypass 528000000 > pll2_bus 528000000 > ca7_secondary_sel 528000000 > step 528000000 > pll1_sw 528000000 > arm 528000000 > 396MHz: > pll2_pfd2_396m 396000000 > ca7_secondary_sel 396000000 > step 396000000 > pll1_sw 396000000 > arm 396000000 > 198MHz: > pll2_pfd2_396m 396000000 > ca7_secondary_sel 396000000 > step 396000000 > pll1_sw 396000000 > arm 198000000 > > Signed-off-by: Anson Huang <Anson.Huang@nxp.com> > Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> For this series: Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Regards Dong Aisheng ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2018-01-09 10:27 UTC | newest] Thread overview: 4+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2018-01-08 2:04 [PATCH V3 1/2] ARM: dts: imx6ul: add 696MHz operating point Anson Huang 2018-01-08 2:04 ` [PATCH V3 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul Anson Huang 2018-01-08 3:43 ` Viresh Kumar 2018-01-09 10:27 ` Dong Aisheng
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).